adoption of the appendices and reference standards of · pdf fileepcot building code 1...

EPCOT Building Code 1

APPENDIX A

ADOPTION OF THE APPENDICES AND REFERENCE STANDARDS OF THE EPCOT BUILDING CODE

SECTION A-101 ADMINISTRATION

A-101.1 Scope. The appendices and Standards identified herein shall be enforced in accordance with the provisions of this Code. A-101.2 Criteria. The Standards listed herein are sponsored by nationally recognized technical and engineering organizations. Where no national standard is available, the EPCOT compilation as listed shall apply. Where the provisions of this Code and the EPCOT Standards are in conflict, the requirements of this Code shall apply.

SECTION A-201 APPENDICES

A-201.1 Legality. The appendices identified in this Subsection are legally a part of this Code and their provisions shall be enforced by the Building Official.

Appendix A Adoption of the Appendices and Referenced Standards of the EPCOT Building Code

Appendix B Fire Limits

Appendix C Calculated Fire Resistance

Appendix D Regulation of Signs and Outdoor Advertising Structures

Appendix E Regulation of Private Swimming Pools

Appendix F Regulation of Building Construction and Demolition Operations

Appendix G Regulations for Construction of Stages, Enclosed Platforms, Motion Picture Projection Rooms and Open-Air Event or Performance Platforms

Appendix H Regulation of Commercial Stables

Appendix I Regulation of Covered Walkways and Malls

Appendix J Group S-4 Occupancies and Manufactured Buildings

Appendix K Tentative Requirements Pertaining to Heat Radiation Between Buildings

Appendix L Tentative Design Criteria for Fire Protection of Exterior Structural Elements

Appendix M Regulations for Construction of Motion Picture and Television Soundstages

Appendix N Regulations for Membrane Structures and Tents

Appendix O Reserved

Appendix P Regulations Covering Building Dead Loads

Appendix Q Regulation of Animal Support Facilities

Appendix R Swimming Pools and Bathing Places

SECTION A-301

EPCOT REFERENCED STANDARDS

A-301.1 Legality. The Standards listed herein are legally part of this Code and their requirements shall be enforced by the Building Official.

EPCOT

Standard Number

Title of Standard

Author Designation and Year of Publication

Chapter 5 – Requirements Based on Occupancy

5-1 Elevators, Dumbwaiters, Escalators, Moving Walks, Manlifts and Transporting Assemblies

EPCOT Compilation

5-2 Health Care Facilities NFPA 99-2002 2010

5-3 EPCOT Accessibility Code for Building Construction

2009 2015 Edition

5-4 Flammable and Combustible Liquids Code

NFPA 30-2003 2010

5-5 Liquefied Petroleum Gas Code NFPA 58-2004 2011

5-6 Dry Cleaning Plants NFPA 32-2000 2011

5-7 Exhaust Systems for Air Conveying of Vapors, Gases, Mists and Noncombustible Particulate Solids

NFPA 91-1999 2010

5-8 Grandstands, Folding and Telescopic Seating, Tents, and Membrane Structures

NFPA 102-2006 2011

5-9 Heliports NFPA 418-2001 2011

5-10 Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements

ISO 10140-1-19972010(en)

5-11 Spray Application Using Flammable or Combustible Materials

NFPA 33-2007 2011

5-12 Safety Standard for Amusement Attractions and Amusement Buildings

EPCOT Compilation

5-13 Amusement Ride and Devices EPCOT Compilation

5-14 Incinerators and Waste and Linen Handling Systems and Equipment

NFPA 82-2004 2009

Chapter 6 – Requirements Based on Type of Construction

6-1 (a) Part 1 - Fire Tests of Building Construction and Materials

ASTM E 119-20002008a

(b) Part 2 - Fire-Resistive Time EPCOT


Periods for Building Components Compilation

6-2 Behavior of Materials in a Vertical Tube Furnace at 750 ° C

ASTM E 136-20042009

6-3 Surface Burning Characteristics of Building Materials

ASTM E 84-2004 2009

6-4 Surface Burning Characteristics of Building Materials

UL 723-2008

Chapter 7 – General Construction Requirements for Fire Safety

7-1 Fire Dampers – with Revisions through January 10, 2002

UL 555-999 2006

7-2 Fire Tests of Door Assemblies (Withdrawn 1995)

ASTM E 152-1981 E2

7-3 Fire Test of Window Assemblies (Withdrawn 1995)

ASTM E 163-1984 E1

7-4 Smoke Detectors for Fire Protective Signaling System – with Revisions through January 1999

UL 268-19962006

7-5 Tin-Clad Fire Doors – with Revisions through March 2003

UL 10-A-19982009

7-6 Fire Doors and Fire Windows NFPA 80-1999 2010

7-7 Fire-Retardant Roof Coverings EPCOT Compilation

7-8 Standards for Application of Veneer

EPCOT Compilation

7-9 Smoke and Heat Venting NFPA 204-2007 2012

7-10 (a) Installation of Sprinkler Systems

NFPA 13-2002 2013

7-10 (b) Sprinkler Systems – in Residential Occupancies up to and including Four Stories in Height

NFPA 13R-2002 2013

7-10 (c) Sprinkler Systems in One- and Two-Family Dwellings, and Manufactured Homes

NFPA 13D-2002 2013

7-11 (a) Low-, Medium, and High-Expansion Foam

NFPA 11-20052010

(b) Medium- and High-Expansion Foam Systems (Withdrawn)

NFPA 11A-20051999

7-12 Wetting Agents NFPA 18-2006 2011

7-13 Dry Chemical Extinguishing Systems

NFPA 17-2002 2009

7-14 Standpipe and Hose Systems NFPA 14-2003 2010

7-15 Portable Fire Extinguishers NFPA 10- 2002 2010

7-16 Halon 1301 Fire-Extinguishing Systems

NFPA 12A-1997 2009

7-17 Ventilation Control and Fire Protection of Commercial Cooking Operations

NFPA 96-20042014

7-18 Criteria for Acceptance of Foam Plastics

EPCOT Compilation

7-19 National Fire Alarm and Signaling Code

NFPA 72-2002 2010

7-20 Installation, Maintenance and Use of Protective Signaling Devices

NFPA 72-2002 2010

7-21 Automatic Fire Detectors NFPA 72-20022010

7-22 Installation, Maintenance and Use of Notification appliances for Protective Signaling Systems

NFPA 72-2002 2010

7-23 Household Fire Warning Equipment

NFPA 72-2002 2010

7-24 Fire Tests of Through-Penetration Fire Stops

ASTM E 814-20022008b

7-25 Installation of Private Fire Service Mains and Their Appurtenances

NFPA 24-20072013

7-26 Inspection, Testing and Maintenance of Water-Based Fire Protection System

NFPA 25-2011

7-27 National Electrical Code NFPA 70-2011

7-28 Standard for Air Leakage Tests of Door Assemblies

UL 1784-2001

7-29 Smoke Management Systems in Malls, Atria and Large Spaces

NFPA 92 B-2005

7-30 Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

ASTM D 2898-2010

7-31 Seamless Copper Pipe, Standad Sizes

ASTM B 42-2002e01

7-32 Seamless Red Brass Pipe, Standard Sizes

ASTM B 43-1998 (2004)

7-33 Seamless Copper Tube, Bright Annealed (Metric)

ASTM B 68-2002

7-34 Seamless Cooper Water Tube ASTM B 88-2003

7-35 General Requirements for Wrought Seamless Copper and Copper-Alloy Tube

ASTM B 251-2002e01

7-36 Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

ASTM B 280-2003

7-37 Cast Copper Alloy Solder Joint Pressure Fittings

ASME B16.18-2001 (Reaffirmed 2005)

7-38 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

ASME B16.22-2001 (Reaffirmed 2005)

7-39 Installation of Smoke Door Assemblies

NFPA 105-2010

7-40 Wet Chemical Extinguishing Systems

NFPA 17A-2009

7-41 Installation of Stationary Pumps for Fire Protection

NFPA 20-2010

7-42 Installation of Carbon Monoxide (CO) Detection and Warning Equipment

NFPA 720-2012


Chapter 9 – Design Requirements

9-1 Laboratory Compaction Characteristics of Soil Using Modified Effort

ASTM D 1557-2002 2007

9-2 Density and Unit Weight of Soil in Place by the Sand-Cone Method

ASTM D 1556-20002007

9-3 Test Method for Piles Under Static Axial Compressive Load (Withdrawn 2006)

ASTM D 1143/D 1143M -1981 (1994)el2007el

9-4 Establishing Allowable Stresses for Round Timber Piles

ASTM D 2899-2003 2012

9-5 Round Timber Piles ASTM D 25-1999el (2005)

9-6 Welded and Seamless Steel Pipe Piles

ASTM A 252-1998 (20022007)

9-7 Minimum Design Loads for Buildings and Other Structures

ASCE 7-2005 2010

9-8 Guide Specifications for Design of Metal Flagpoles

ANSI/NAAMM FP 1001-1997

9-9 Structural Standards for Steel Antenna Towers and Antenna Supporting Structures (Revised 2003)

ANSI/TIA -222F-1996

9-8 Approval Standard for Class 1 Insulated Steel Deck Roofs

FM 4450-1989

9-9 Approval Standard for Single-Ply, Polymer-Modified Bitumen Sheet, Built-Up Roof (BUR) and Liquid Applied Roof Assemblies for use in Class 1 and Noncombustible Roof Deck Construction

FM 4470-2012

9-10 Tests for Uplift Resistance of Roof Assemblies

UL 580-2006

9-11 Uplift Tests for Roof Covering Systems

UL 1897-2012

9-12 Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference

ASTM E 1592-2005 (2012)

Chapter 10* - Requirements Based On Quality, Design and Application of the

Materials of Construction

*The listing of EPCOT Standards for Chapter 10, because of its length, is subdivided into sections for each material. Except when Test Method is indicated, the Standard is a specification.

Section 1002-Aluminum

1002-1 Specifications for Aluminum Structures

Aluminum Association-2005

1002-2 Aluminum and Aluminum-Alloy Sheet and Plate

ASTM B 209-2004 2007

1002-3 Aluminum and Aluminum-Alloy Drawn Seamless Tubes

ASTM B 210-2004 2012

1002-4 Aluminum and Aluminum-Alloy ASTM B 211-

Rolled or Cold Finished Bars, Rods and Wire

2003 2012el

1002-5 Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

ASTM B 221-2008 2013

1002-6 Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers

ASTM B 234-20042010

1002-7 Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

ASTM B 241/B 241M-20022012el

1002-8 Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings and Rolled Ring Forgings

ASTM B 247-2002a2009

1002-9 Aluminum-Alloy 6061-T6 Standard Structural Profiles

ASTM B 308/B 308M-20022010

1002-10 Structural Welding Code-Aluminum

AWS D1.2

1002-11 Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods

ASTM B 316/B 316M-2002 2010

1002-12 Aluminum-Alloy Extruded Structural Pipe and Tube

ASTM B 429/B 429M-2006 2010el

Section 1003-Concrete Construction

1003-1 Building Code Requirements for Structural Concrete

ACI 318/318R-2005 2011

1003-2 Reserved Building Code Requirements for Structural Plain Concrete

ACI 318/318R-2002

1003-3 Portland Cement ASTM C 150-20042007

1003-4 Reserved

1003-5 Blended Hydraulic Cements ASTM C 595-20032008a

1003-6 Concrete Aggregates ASTM C 33/C 33M 2008-2003

1003-7 Lightweight Aggregates for Structural Concrete

ASTM C 330-20042005

1003-8 Organic Impurities in Fine Aggregates for Concrete

ASTM C 40-2004/C 40M-2011

1003-9 Air-Entraining Admixtures for Concrete

ASTM C 260-2006/C 260M-2010a

1003-10 Chemical Admixtures for Concrete ASTM C 494/C 494M-1999

1003-11 Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Concrete

ASTM C 618-20082012a

1003-12 Deformed and Plain Billet-Steel Bars for Concrete Reinforcement

ASTM A 615/A 615M-2004a2009

1003-13 Rail-Steel Deformed and Plain Bars for Concrete Reinforcement (Withdrawn)

ASTM A 616/A 616M-1996a -1979

1003-14 Axle-Steel Deformed and Plain Bars for Concrete Reinforcement

ASTM A 617 617-1979


(Withdrawn)

1003-15 Fabricated Welded Deformed Steel Bar Mats for Concrete Reinforcement

ASTM A 184-2006/A 184M 2006 (2011)

1003-16 Steel Wire, Plain, for Concrete Reinforcement

ASTM A 82-2002

1003-17 Steel-Welded Wire Reinforcement, Plain for Concrete

ASTM A 185-2002

1003-18 Steel Strand, Uncoated Seven-Wire for Prestressed Concrete

ASTM A 416-2002/A 416M 2006

1003-19 Uncoated Stress-Relieved Steel Wire for Prestressed Concrete

ASTM A 421/A 421M-2002

1003-20 Structural Welding Code- Reinforcing Steel

AWS D1.4-1998

1003-21 Low and Intermediate Tensile Strength Carbon Steel Plates

ASTM A 283/ A 283 M-2003 (2007)

1003-22 Index of Specifications for Ductile- Iron Pressure Pipe

ASTM A 377-2003 (2008)el

1003-23 Selecting ACI- Proportions for Normal, Heavyweight and Mass Concrete

ACI 211.1-1991 (Reapproved 2009)

1003-24 Selecting ACI- Proportions for Structural Lightweight Concrete

ACI 211.2-1998 (Reapproved 2004)

1003-25 Evaluation of Strength Test Results of Concrete

ACI 214/214R-2002 2011

1003-26 Making and Curing Concrete Test Specimens in the Laboratory

ASTM C 192/C 192M-20072014

1003-27 Sampling Freshly Mixed Concrete ASTM C 172-20042008

1003-28 Compressive Strength of Cylindrical Concrete Specimens

ASTM C 39-1999ael

1003-29 Obtaining and Testing Drilled Cores and Sawed Beams of Concrete

ASTM C 42/C 42M-1999

1003-30 Splitting Tensile Strength of Cylindrical Concrete Specimens

ASTM C 496/C 496M-2004el 2011

1003-31 Ready-Mixed Concrete ASTM C 94/C 94M-2004 2009

1003-32 Design and Control of Concrete Mixtures

PCA 14th 15th Edition

The following Standards appearing in other Sections also shall apply to Section 1003:

EPCOT Standard Number

Title of Standard


1009-12 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless Specification for Cast Iron Soil Pipe and Fittings

ASTM A 53-20072012

Section 1004-Gypsum Concrete and Precast Gypsum

1004-1 Reinforced Gypsum Concrete EPCOT Compilation

1004-2 Physical Testing of Gypsum, Gypsum Plaster and Gypsum Concrete

ASTM C 472-1999 (2004)

1004-3 Physical Testing of Gypsum Panel Products

ASTM C 473-2010 2007

1004-4 Gypsum Concrete ASTM C 317/C 317M-2000 (2005)

1004-5 Chemical Analysis of Gypsum and Gypsum Products

ASTM C 471M-2001 (2006)el




1003-16 ASTM A 82-2002

1003-17 ASTM A 185-2002/A 185M-2006 (2011)

1003-20 AWS D1.4-1998

1007-9 ASTM C 28-2000e01/C 28M-2000 (2005)

1009-20 ASTM A 242-2009 /A 242M-2013

Section 1005-Glass and Glazing

1005-1 Architectural Glazing Material CPSC16-CFR, Part 1201 (1977)-2002

1005-2 Safety Glazing Materials Used in Buildings -- Safety Performance Specifications and Methods of Test (Reaffirmed 1994)

ANSI Z97.1-1984 (R 1994)2009

1005-3 Glass Masonry Structures ACI 530-20052011 ASCE 5-20022011 TMS 402-20052011

Section 1006-Masonry

1006-1 Building Code Requirements for Masonry Structures

ACI 530-20052011 ASCE 5-20052011 TMS 402-052011

1006-2 Masonry Structures ACI 530.1-20052011 ASCE 6-20052011 TMS 602-20052011

1006-3 Building Brick (Solid Masonry Units Made from Clay or Shale)

ASTM C 62-20042008

1006-4 Calcium Silicate Face Brick (Sand-Lime Brick)

ASTM C 73-1999a2005


1006-5 Facing Brick (Solid Masonry Units Made from Clay or Shale)

ASTM C 216-2004a2007a

1006-6 Concrete Brick ASTM C 55-20032006e01

1006-7 Load-Bearing Concrete Masonry Units

ASTM C 90-20032008

1006-8 Reserved

1006-9 Non-Load-Bearing Concrete Masonry Units

ASTM C 129-20062014

1006-10 Structural Clay Load-Bearing Wall Tile

ASTM C 34-2003

1006-11 Structural Clay Non-Load-Bearing Tile

ASTM C 56-1996 (2001)2005

1006-13 Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

ASTM C 126-1999 (2005)

1006-14 Structural Clay Facing Tile ASTM C 212-2000 (2006)

1006-16 Masonry Cement ASTM C 91-2003a2005

1006-17 Quicklime for Structural Purposes ASTM C 5-2003

1006-18 Hydrated Lime for Masonry Purposes

ASTM C 207-20042006 (2011)

1006-19 Finishing Hydrated Lime (1984) ASTM C 206-2003

1006-20 Blended Hydraulic Cements ASTM C 595-2003/C 595M-2014

1006-21 Aggregates for Masonry Mortar ASTM C 144-20032011

1006-22 Aggregates for Masonry Grout ASTM C 404-20072011

1006-23 Mortar for Unit Masonry ASTM C 270-20042008a

1006-24 Sampling and Testing Brick, and Structural Clay Tile

ASTM C 67-2003ae012008

1006-25 Sampling and Testing Concrete Masonry Units and Related Units

ASTM C 140-20032008a

1006-26 Packaged, Dry, Combined Materials for Surface- Bonding Mortar

ASTM C 887-1979a (2001)2005

1006-27 Building Brick (Solid Masonry Units Made from Clay or Shale)

ASTM C 62-20042008

1006-28 Lightweight Aggregates for Concrete Masonry Units

ASTM C 331-20042005

1006-29 Grout for Masonry ASTM C 476-20022010

1006-30 Sampling and Testing Grout ASTM C 1019-2003 2009




1003-3 ASTM C 150-20042007

1003-12 ASTM A 615/A 615 M-2004a2009

1003-13 ASTM A 616/A 616 M-1996a1979

1003-14 ASTM A 617-1979

1003-15 ASTM A 184/A 184 M-2006 (2011)

1003-16 ASTM A 82-2002

1003-17 ASTM A 185-2002

Section 1007 - Plastering, Lathing and Installation of Wallboard

1007-1 (a) Application of Portland Cement-Based Plaster

ASTM C 926-1998a2006

(b) Installation of Interior Lathing and Furring

ASTM C 841-2003 (2008)el

1007-2 Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster

ASTM C 1063-20032008

1007-3 Gypsum Wallboard ASTM C 36/C 36M-2003

1007-4 Application and Finishing of Gypsum Board

GA 216-20042007

1007-5 Gypsum Backing Board, Gypsum, Coreboard and Gypsum Shaftliner Board

ASTM C 442/C 442M-2004

1007-6 Treated Core and Non-Treated Core Gypsum Sheathing Board

ASTM C 79-2004a

1007-7 Gypsum Lath ASTM C 37/C 37M-2001

1007-8 Inorganic Aggregates of Use in Gypsum Plaster

ASTM C 35 1995-2001 (2005)

1007-9 Gypsum Plasters ASTM C 28/C 28M-2000e012000 (2005)

1007-10 Gypsum Casting and Molding Plaster

ASTM C 59/C 59M-2000 (2006)

1007-11 Finishing Hydrated Lime ASTM C 206-2003

1007-12 Gypsum Keene’s Cement ASTM C 61/C 61M-2000 (2006)

1007-13 Adhesives for Fastening Gypsum Wallboard to Wood Framing

ASTM C 557-2003e01

1007-14 Joint Compound and Joint Tape for Finishing Gypsum Wallboard

ASTM C 475-2001 /C 475M-2002 (2007)





1003-3 ASTM C 150-20042007

1003-5 ASTM C 595-20032008a

1003-15 ASTM E A 184-1996 (Withdrawn 2002)/A 184M-2006 (2011)

1006-16 ASTM C 91-2003a2005

Section 1008-Plastics

1008-1 Ignition Properties of Plastics ASTM D 1929-1996 (2000)e01

1008-2 Rate of Burning and/or Extent of Time of Burning of Self-Supporting Plastics in a Horizontal Position

ASTM D 635-2003 2006

1008-3 Density of Smoke from the Burning or Decomposition of Plastics

ASTM D 2843-1999 (2004)e01

Section 1009-Steel

1009-1 Specifications for Structural Steel Buildings - Allowable Stress Design and Plastic Design (including Supplement No. 1, 2001)(Superceeds AISC 335-1989s1)

AISC 335-1989s1ANSI/AISC 360-2005

1009-2 (a) Specification for Design of Cold-Formed Steel Structural Members, with Supplement 1

AISI S100-2007/S1-2010 2002 Edition

(b) Specification for the Design of Cold-Formed Stainless Steel Structural Members

ASCE 8-2002

1009-3 (a) Standard Specifications for Open-Web Steel Joists K-Series

SJI K-2000

K-1.1-20052010

(b) Standard Specifications for Longspan Steel Joists, LH-Series and Deep Longspan Steel Joints, DLH Series

SJI-2000

LH/DLH-1.1-2005-2010

(c) Standard Specifications and for Load Tables and Weight Tables for Steel Joists and Joist Girders

SJI 42nd 43rd Edition-20022010

(d) Recommended Code of Standard Practice for Steel Joists and Joist Girders

SJI 42nd EditionCOSP-20022010

1009-4 Structural Applications of Steel Cables for Buildings

2002 ASCE 19-19962009

1009-5 (a) Structural Welding Code - Steel AWS D1.1-2004

(b) Structural Welding Code - Sheet Steel

AWS D1.3-1998

1009-6 Specification for Structural Joints Using ASTM A 325 or A 490 Bolts

RCSC-20041988

1009-7 Structural Steel ASTM A 36/A 36M-20042008

1009-8 Steel Casting, Carbon, for General Application

ASTM A 27/A 27M-20082013

1009-9 Gray-Iron Castings ASTM A 48/A 48M-20082003

(2012)

1009-10 (a) Carbon Steel Electrodes and Rods for Gas-Shielded Arc Welding

AWS A 5.18/A5.18M-2005

(b) Carbon Steel Electrodes for Flux-Cored Arc Welding

AWS A5.20/A5.20M-2005

1009-11 Reserved

1009-12 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless Specification for Cast-Iron Soil Pipe and Fittings

ANSI/ASTM A 53-20072012

1009-13 Structural Steel (SS), Sheet, Carbon Coil-Rolled, Carbon (Withdrawn)

ASTM A 611 611-1997

1009-14 Steel, Sheet and Strip, Carbon, Hot-Rolled (Withdrawn)

ASTM A 570/ A 507M-1998

1009-15 Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength

ASTM A 307-20032007b

1009-16 Structural Bolts, Steel, Heat-Treated, 120/105 ksi Minimum Tensile Strength

ASTM A 325-1994

1009-17 Quenched- and Tempered-Alloy Steel Bolts, Studs, and other Externally Threaded Fasteners

ASTM A 354-2007a2011

1009-18 Steel, Sheet and Strip, High-Strength, Low-Alloy, Hot-Rolled and Code-Rolled, with Improved Atmospheric Corrosion Resistance

ASTM A 606-2009 /A 606M-2009a

1009-19 Steel, Sheet and Strip, High-Strength, Low-Alloy, Columbium and/or Vanadium Hot-Rolled and Cold-Rolled (Withdrawn 2000)

ASTM A 607-1998

1009-20 High-Strength, Low-Alloy Structural Steel

ASTM A 242/ A 242M-2004 (2009)el2013

1009-21 High-Strength, Low-Alloy Structural Manganese Vanadium Steel (Withdrawn 1989)Columbium-Vanadium Structural Steel

ASTM A 572/A 572M-2007

1009-22 Steel Sheet, Zinc-Coated (Galvanized) by the Hot-Dip Process, Structural (Physical) Quality (Withdrawn 1994)

ASTM A 446/A 446M-1993

1009-23 Hex Cap Screws, BeltsBolts, and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

ASTM A 449-2007b 2010

1009-24 Heat-Treated Steel Structural Bolts, 150 ksi Minimum Tensile Strength

ASTM A 490-1993

1009-25 Rivets, Steel, Structural ASTM A 502-2003 (2009)

1009-26 High-Strength, Low-Alloy Columbium-Vanadium Structural Steel

ASTM A 572/ A 572M-20042007

1009-27 Seamless Carbon Steel Pipe for High-Temperature Service

ASTM A 106/A 106M-20082014


1009-28 Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes

ASTM A 500-2007/A 500M-2013

1009-29 Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

ASTM A 501-2007

1009-30 Steel Castings, High-Strength for Structural Purposes

ASTM A 148/A 148M-2008

1009-31 Steel Forgings, Carbon and Alloy, for General Industrial Use

ASTM A 668/A 668M-2004 2013el

1009-32 High-Strength, Low-Alloy Structural Steel with 50 psi Minimum Yield Point to 4 Inches Thick

ASTM A 588/ A 588M-20042005

1009-33 Steel Bars, Carbon, Merchant Quality, Mechanical Properties

ASTM A 663/A 633M-1989 (2006)2012

1009-34 Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties

ASTM A 675/A 675 M-2003 20092014

1009-35 Mechanical Testing of Steel Products

ANSI/ASTM A 370-2009a2014

1009-36 High-Yield-Strength, Quenched- and Tempered-Alloy Steel Plate, Suitable for Welding

ASTM A 514/ A 514M-20052014

1009-37 High-Strength Carbon-Manganese Steel of Structural Quality

ASTM A 529/A 529M-2005 (2009)

1009-38 Steel Joists Shop Paint Primer/Metal Building Primer

SSPC SSPC-Paint 15

1009-39 Steel Deck Institute Design Manual for Composite Decks, Form Decks and Roof Decks

SDI # 31-2007

1009-40 Load and Resistance Factor Design Specifications for Structural Steel Buildings

AISC 360-20052010

The following Standards appearing in other Sections apply to the use of steel pipe piles, welding and reinforcing steel:



9-6 ASTM A 552 (Withdrawn)252-1998(2007)

1003-12 ASTM A 615-2004a /A 615M-2009

1003-13 ASTM A 616-1996a 1979 (Withdrawn)

1003-14 ASTM A 617 -1979 (Withdrawn)

1003-15 ASTM A 184-2006/A 184M 2006 (2011)

1003-16 ASTM A 82-2002

1003-17 ASTM A 185-

2002

1003-18 ASTM A 416-2002 /A 416M 2006

1003-19 ASTM A 421-2002/A 421M 2002

1003-20 AWS D1.4-1998

1003-21 ASTM A 283-2003 /A 283M 2003 (2007)

1003-22 ASTM A 377-2003 (2008)e1

Section 1010-Wood

1010-1 (a) National Design Specification for Wood Construction (with 2005 Supplement)

AF&PA NDS-20052012

(b) Special Design Provisions for Wind and Seismic

AF&PA SDPWS-2005 2008

1010-2 (a) Span Tables for Joists and Rafters

AF&PA-2005 2012 ANSI/AF&PA

(b) Design Values for Joists and Rafters

AF&PA-2005

1010-3 Wood Construction Data No. 4, Plank and Beam Framing for Residential Buildings

AF&PA WCD-4-2003 ANSI/AF&PA

1010-4 Structural Glued-Laminated Timber of Softwood Species – Design Requirements – Standard Specifications for Structural Glued-Laminated Timber of Softwood Species – Manufacturing Requirements

AITC 117-2004 2010

1010-5 Reserved

1010-6 Reserved

1010-7 Reserved

1010-8 Plywood Design Specification (Revised 1998)

APA PDS-Y510J-1997 2004

1010-9 Wood

1010-10 Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber

ASTM D 245-2006 (2011)

1010-11 Standard Specification for Grades of Southern and Tidewater Red Cypress

SCMA-June 1, 1986

1010-12 Southern Pine Inspection Bureau Grading Rules

SPIB-20022014

1010-13 Standard Grading Rules for West Coast Lumber

WCLIB 17 17-2004

1010-14 Standard Specifications for Grades of California Redwood Lumber

California Redwood Association-2000 Edition

1010-15 Western Lumber Standard Grading Rules for Western Lumber

WWPA g-5-19982011


1010-16 Official Grading Rules for Northern Hardwood and Pine

NHPMA

1010-17 Standard Grading Rules for North- eastern Lumber

NeLMA-2006 2013

1010-18 Structural Glued-Laminated Timber

AITC/ANSI A 190.1-19922007

1010-19 U.S. Product Standard for Construction and IndustrialStructural Plywood

National Bureau of Standards PS1-1995NIST-2009

1010-20 (a) All Timber Products – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C1-2000 2003

(b) Lumber, Timber, Bridge Ties and Mine Ties – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C2-2001 2002

(c) Piles – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C3-1999 2003

(d) Poles – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C4-1999 2003

(e) Sawn Timber Piles Used To Support Residential and Commercial Structures (Withdrawn)

AWPA C24-19962003

(f) Posts – Pressure Treatment (Withdrawn)

AWPA C5 C5-2003 (Withdrawn)

(g) Plywood – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C9-20002003

(h) Wood Block for Floors and Platforms Pressure Treatment (Withdrawn)

AWPA C11 C11-2001

(i) Wood for Commercial-Residential Construction – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C15-2000 2003

(j) Round Poles and Posts Used in Building Construction – Preservative Treatment by Pressure Processes (Withdrawn)

AWPA C23-2000 2003

(k) Structural Glued-Laminated Members and Laminations Before Gluing (Withdrawn)

AWPA C28-1999 2003

1010-21 (a) Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

ASTM D 2898-1999 2007

(b) Hygroscopic Properties of Fire-Retardant Wood and Wood-Base Products

ASTM D 3201-1998el 2008a

(c) Structural Lumber, Fire-Retardant Pressure Treatment (Withdrawn)

AWPA C20 C20-2002

(d) Plywood -- Fire-Retardant Treated by Pressure Processes (Withdrawn)

AWPA C27-2002

1010-22 American Standard Specifications and Dimensions for Piles and

ANSI 05.1-2002

Poles, Wood Poles (Cancelled)

1010-23 Federal Specification for Insulating Fiberboard and Block Insulation Board, Thermal (Cellulosic Fiber) (Cancelled)

LLL-1-535B 535B-1977

1010-24 Fiberboard Nail-Base Sheathing (Withdrawn 1992)

ASTM D 2277-1987

1010-25 Federal Specifications for Nails, Wire, Brads, and Staples and Spikes: Wire, Cut and Wrought

FF-N-105b105B-March 17, 1971

1010-26 Cellulostic Fiber Insulating Board ASTM C 208-1995 (2001)2008aASTM C 209-1998

1010-27 (a) Basic Hardboard AHA A 135.4-1995 2004

(b) Prefinished Hardboard Paneling

AHA A 135.5-1995 2004

(c) Hardboard Siding AHA A 135.6-1998

1010-28 Building Board (Wood Particleboard) Hard Pressed, Vegetable Fiber (S/S by ANSI A208.1) (Cancelled)

ANSI/ A 208.1-1999

1010-29 Evaluating Properties for Wood-Base Fiber and Particle Panel Materials

ASTM D 1037-2006a 2012

1010-30 Residential & Commercial Design/APA Engineered Wood Construction Guide

APA APA-2011

1010-31 National Design Standards For Metal-Plate-Connected Wood Truss Construction

TPI 1-2002 2007

1010-32 Performance Standards and Policies for Structural-Use Panels

APA PRP 108

1010-33 Adhesives for Field-Glueing Plywood to Wood Framing

APA AFG-01-March 1991

1010-34 Wood Construction Data No. 6, Design of Wood Frame Structures for Permanence

AF&PA WCD6-2001 2006

1010-35 Test Method for Evaluating the Flexural Properties of Fire-Retardant-Treated Softwood Plywood Exposed to the Elevated Temperatures

ASTM D 5516-2003

1010-36 Technical Report No. 7, The Permanent Wood Foundation System. (Replaced)

AF&PA TR 7-March 1987

1010-37 Zinc Coated (Hot-Dip) on Iron and Steel Hardware

ASTM A 153/A 153M-2005

1010-38 Coatings of Zinc Mechanically Deposited on Iron and Steel Strip for Building Construction

ASTM B 695-2004

The following Standard referenced in other Sections shall also apply to Section 1010:




6-3 ASTM E 84-20042009

7-8 EPCOT Compilation

9-4 ASTM D 2899-20032012

9-5 ASTM D 25-1999 (2005)

1007-1 ASTM C 926-2006

Section 1011 – Thermal Insulating Material

1011-1 EPCOT Energy Efficiency Code for Building Construction

20092015

1011-2 Energy Standard for Buildings, Except Low-Rise Residential Buildings, I-P Edition

ANSI/ASHRAE/ IESNA 90.1-20072013

1011-3 Advanced Energy Design Guide for Small Office Buildings (Guide)

ANSI/ASHRAE-2004

Appendix N – Regulations for Membrane Structures and Tents

N-1 Standard Practice for Design, Manufacture, Operation, and Maintenance of Inflatable Amusement Devices

ASTM F2374-2010

Appendix R – Swimming Pools and Bathing Places

R-1 Circulation System Components and Related Materials for Swimming Pool, Spas/Hot Tubs

NSF/ANSI 50-2007

R-2 Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs

ASTM F1346-1991 (R2003)

R-3 Standard for Public Swimming Pools

ANSI/NSPI-1-2003

R-4 Standard for Public Spas ANSI/NSPI-2-1999 R-5 Standard for Suction Entrapment

Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins

ANSI/APSP-7-2006

R-6 Drinking Water Treatment Chemicals – Health Effects

NSF/ANSI 60-2005

R-7 Dimensional Standards National Collegiate Athletic Association-1998

R-8 Federation Internationale de Natation Amateur Handbook

FINA 1998-2000

R-9 Official Rules of Diving & Code Regulation of United States Diving Inc.

1998-1999

R-10 United States Swimming Rules and Regulations

1998

R-11 National Federation of State High School Associations

1997-1998

R-12 Federation Internationale de Natation Amateur Handbook

FINA 2005-2009

R-13 National Electrical Code NFPA 70-2011 R-14 Suction Fitting for use in Pools,

Spas & Hot Tubs - Marking ASME/ANSI A112.19.8-2007

R-15 USEPA Ultraviolet Disinfectant Guidance Manual

EPA 815-R-06-007-Nov. 2006

EPCOT Standard 5-1

5-1-1 Safety Code for Elevators and Escalators – with A17.1a/CSA B44a-2008 Addenda

ASME A17.1-2008

5-1-2 Guide for Inspection of Elevators, Escalators, and Moving Walks

ASME A17.2-2012

5-1-3 Safety Standard for Belt Manlifts ASME A90.1-2003 5-1-4 Safety Code for Conveyors,

Cableways and Related Equipment

ASME B20.1-2003

5-1-5 Safety Code for Existing Elevators and Escalators

ASME A17.3-1996

5-1-6 Safety Standard for Platform Lifts and Stairways Chairlifts

ASME A18.1-2008

5-1-7 Elevator and Escalator Electrical Equipment

ASME A 17.5

EPCOT Fuel Gas Code 1

CHAPTER 11

REFERENCED STANDARDS

This Chapter lists the standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title, and the section or sections of this document that reference the standard.

AGA

Amercian Gas Association 400 North Capitol Street, NW Suite 450 Washington, DC 20001

Standard Reference number

Title Referenced in code

section number

3—87 Requirements for Gas Connectors for Connection of Fixed Appliances for Outdoor Installation, Park Trailers and Manufactured (Mobile) Homes to the Gas Supply

315.6

ANSI

American National Standards Institute 11 West 42nd Street 13th Floor 25 West 43rd Street 4th Floor New York, NY 10036



section number

LC 1—97 Standard for Interior Fuels Gas Piping Systems Using Corrugated Steel Tubing

306.2

Z21.8—94 (2002) Installation of Domestic Gas Conversion Burners 512

Z21.10.1—04 Gas Water Heaters, Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu per Hour or Less, with Addenda Z21.10.1a—02

504.6.1

Z21.10.3—01 Gas Water Heaters, Volume III, Storage Water Heaters with Input Ratings Above 75,000 Btu per Hour, Circulating and Instantaneous Water Heaters, with Addenda Z21.10.3a—03 and Z21.10.3b—04

504.6.1

Z21.12—90(R2000) Draft Hoods 604.4

Z21.15—97 Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves, with Addenda Z21.15a—01 (R2003)

306.10

Z21.21—9712 Automatic Valves for Gas Appliances, with Addenda Z21.21a—97 and Z21.21b—97 69a—2003

306.10

Z21.69—02 Connectors for Movable Gas Appliances 403.1.1

Z83.4—9113 Direct Gas-Fired Makeup Air Heaters 514.1.1

Z83.18—9012 Direct Gas-Fired Industrial Air Heaters, with Addenda Z83.18a—91 515.1.1

API American Petroleum Institute 1200 L Street, NW Washington, DC 20005



section number

1104—1014 Welding of Pipelines and Related Facailites—20th Edition,

Includes Errata 1 (2007) and 2 (2008)

306.5.3


ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers 1791 Tullie Circle NE Atlanta, GA 30329



section number

ASHRAE—80 Handbook and Product Directory Systems 507.6

ASME American Society of Mechanical Engineers Three Park Avenue New York, NY 10016



section number

B1.20.1—02(R2006) Pipe Threads 307.1

B16.33—02 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes 1/2 through 2)

306.10

B31.1—0712 Power Piping 306.5.3

B36.10M—0004 Welded and Seamless Wrought-Steel Pipe 306.1, 902.1.1

ASTM American Society for Testing and Materials 100 Barr Harbor Drive West Conshohocken, PA 19428

1916 Race Street

Philadelphia, PA 19103



section number

A 53/A 53M—0206a Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless Steel Pipe

306.1

A 106—04/A 106a—06a Specification for Seamless Carbon Steel Pipe for High-Temperature Service

306.1

A 254—97(02) Specification for Copper-Brazed Steel Tubing 306.2

A 539—99 (Withdrawn 2004) Specification for Electric-Resistance-Welded Coiled Steel Tubing for Gas and Fuel Oil Lines

902.1.1

B 88—03 Specification for Seamless Copper Water Tube 306.2, 902.1.1

B 280—0313 Specification for Seamless Copper Water Tube for Air-Conditioning and Refrigeration Field Service

902.1.1

D 2385—87 (Withdrawn 1995)

Test for Hydrogen Sulfide and Mercaptan Sulfur in Natural Gas (Cadmium-Sulfate Iodemetric Titration Method)

306.1, 306.2

D 2420—8613 Test for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method)

306.2

D 2513—04a07a Specification for Thermoplastic Gas Pressure Pipe, Tubing and Fittings 306.3

D 2517—81 (1987)06 (2011) Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings 306.3

D 2683—8814 Specification for Socket-Type Polyethylene for Outside Diameter-Controlled Polyethylene (PG) Pipe

902.1.1

D 3261-88a12e1 Specification for Butt Heat-Fusion Polyethylene Plastic Fittings for Polyethylene Plastic Pipe and Tubing

902.1.1


CODES This model code is intended to be utilized in conjunction with the other model codes that are adopted by the jurisdiction.



section number

EPCOT Building Code—2009 2015 Edition Chapter 1, 201.3, 309.1, 407

EPCOT Energy Efficiency Code for Building Construction—2009 2015 Edition

525.1

EPCOT Fire Prevention Code—2009 2015 Edition 201.3

EPCOT Mechanical Code—2009 2015 Edition Chapter 1, 201.3, 507.9, 507.12

EPCOT Plumbing Code—2009 2015 Edition Chapter 1, 201.3, 504.2.2, 507.14.3

HUD US Department of Housing and Urban Development 451 7th Sreet, SW Washington, DC 20410



section number

24 CFR, Part 3280—0608 Manufactured Home Construction and Safety Standards 406

HYDI The Hydronics Institute 35 Russo Place

Berkeley Hights, NJ 07922

2107 Wilson Boulevard Suite 600 Arlington, VA 22201



section number

IBR 200—89 Installation Guide for Residential Hydronic Heating Systems 507.6

IBR 250—95 Advanced Installation Guide for Hydronic Heating Systems 507.6

NFPA National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169



section number

37—0206 Stationary Combustion Engines and Gas Turbines 524

52—8813 Compressed Natural Gas Vehicular Fuel Systems 529

54—0915 National Fuel Gas Code 511.1, D103.1

70—0911 National Electrical Code Chapter 1, 309.12.1, 404.1

90A—9615 Installation of Air-Conditioning and Ventilating Systems 507.9.2

90B—9615 Residence-Type Warm-Air Heating and Air-Conditioning Systems 507.9.2


UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, IL 60062



section number

842—93(R2011) Valves for Flammable Fluids 306.10

SECTION 1101

REFERENCED STANDARDS 1101.1 Guide to Various Standards. The following Subsection provides lists intended to be used as a guide to the diverse standards for materials, equipment and accessories, which are required by this Code. Standards for installation also are included.

1101.1.1 Standards for Material Specifications.

Aluminum Pipe and Tubing

Standard Designation Title

ASTM B 210—9512 Standard Specification for Aluminum-Alloy Drawn Seamless Tubes

ASTM B 241—96/B 24M—12el Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

Copper-Alloy Fittings


ANSI/ASME B16.22—8913 Wrought Copper and Copper Alloy Solder Solder-Joint Pressure Fittings

ANSI/ASME B16.26—8813 Cast -Copper -Alloy Fittings for Flared Copper Tubes

Copper and Brass Pipe and Tubing


ASTM B 88—9603 Standard Specification for Seamless Copper Water Tube

ASTM B 280—9813 Standard Specification for Seamless Copper Water Tube for Air Conditioning and Refrigeration Field Service

Corrugated Stainless Steel Tubing


ANSI/AGA LC-1—97/CSA 6.26—14 Standard for Interior Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing

Flanges


ANSI B16.1—9909 (R2004) Standard for Cast Iron Pipe Flanges and Flanged Fittings—Classes 25, 125, 250 and 800

ANSI B16.5—8113 Standard for Steel Pipe Flanges and Flanged Fittings, Including Ratings for Classes 150, 300, 400, 600, 900, 1500 and 2500

ANSI B16.20—9312 Standard for Ring-Joint Gaskets and Grooves for Steel Pipe Flanges

ANSI/AWWA A21.11/C111—0612 Standard for Rubber Gasket Joints for Ductile Iron Pressure Pipe Fittings

Miscellaneous


ANSI B2.1—68ANSI/ASME B1.20.1—13 Standard for Pipe Threads (Except Dryseal)Pipe Threads, General Purpose (Inch)

ANSI/MSS SP-58—9309 Standard Practice for Pipe Hangers and Supports—Materials, Design and Manufacturer Selection, Application and Installation

ASME BPVC—9515 Boiler and Pressure Vessel Code (1995 Edition)

ASTM D 2385—87 (Withdrawn 1995) Standard Test for Hydrogen Sulfide and Mercaptan Sulfur in Natural Gas


(Cadmium Sulfate-Iodometric Titration Method)

ASTM D 2420—8613 Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method)

Plastic Piping, Tubing and Fittings


ASTM D 2513—9807a Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing and Fittings

ASTM D 2517—81 (1987)06 (2011) Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings

ASTM D 2683—8814 Standard Specification for Socket-Type Polyethylene Fittings for Outside- Diameter-Controlled Polyethylene (PE) Pipe and Tubing

ASTM D 3261—88a12e1 Standard Specification for Butt Heat Fusion Polyethylene Plastic Fittings for Polyethylene Plastic (PE) Pipe and Tubing

Steel Pipe and Tubing


ANSI A21.52—76 (Withdrawn 1981) Standard for Ductile Iron Pipe, Centrifugally Cast in Metal Molds or Sand-Lined Molds, for Gas

ASME B36.10/B36.10M—7904 Standard for Welded and Seamless Wrought-Steel Pipe

API 56—80 Carbon Steel Pipe Gas Line

ASTM A 53—88a/A53M—06a Standard Specification for Black and Hot-Dipped, Zinc Coated Welded and Seamless Steel PipePipe, Steel, Black and Hot Dipped, Zinc Coated, Welded and Seamless

ASTM A 106/A106M—96a06a Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service

ASTM A 254—88 Standard Specification for Copper-Brazed Steel Tubing

ASTM A 377—8414 Standard Index of Specifications for Gray Iron and Ductile Iron Pressure Pipe

ASTM A 539—8890a Standard Specification for Electric Resistance- Welded Coiled Steel Tubing for Gas and Fuel Oil Lines

1101.2.2 Standards for equipment and accessory equipment.

Accessory equipment


ASCE/SEI 25—06 Earthquake Actuated Automatic Gas Shutoff Devices

ANSI Z21.2—92 Gas Hose Connectors for Portable Indoor Gas-Fired Appliances(Note: Included in ANSI Z21.101)

ANSI Z21.12—90 (R2000) Draft Hoods

ANSI Z21.15—97 Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves

ANSI Z21.17—9198 (R2014) Domestic Gas Conversion Burners

ANSI Z21.18—8707 (R2012) Gas Appliance Pressure Regulators, with Addenda Z21.18a—89, and Z21.18b—92

ANSI Z21.20—8914 Automatic Gas Ignition Systems and Components, with Addenda Z21.20a—91 and Z21.20b—92Electrical Controls for Household and Similar Use

ANSI Z21.21—8712 Automatic Valves for Gas Appliances, with Addenda Z21.21a—89 and Z21.21b—92

ANSI Z21.22—8699 (R2014) Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems, with Addenda Z21.22a—90

ANSI Z21.23—8910 Gas Appliance Thermostats, with Addenda, Z21.23a—91

ANSI Z21.24—8706 (R2011) Metal Connectors for Gas Appliances, with Addenda Z21.24a—90 and Z21.24b—92

ANSI Z21.35—8905 (R2011) Pilot Gas Filters


ANSI Z21.41—8914 Quick-Disconnect Devices for Use With Gas Fuel, with Addenda, Z21.41a—90, and Z21.41b—92 Appliances

ANSI Z21.45—9295 Flexible Connectors of Other Than All-Metal Construction for Gas Appliances

ANSI Z21.54—8714 Gas Hose Connectors for Portable Outdoor Gas-Fired Appliances, with Addenda Z21.54a—92

ANSI Z21.66—8896(R2001) Electrically Operated Automatic Vent Damper Devices for Use with Gas Fired Appliances, with Addenda, Z21.66a—90 and Z21.66b—91

ANSI Z21.69—9702 Connectors for Movable Gas Appliances

ANSI Z21.70—81 Earthquake Actuated Automatic Gas Shutoff Systems (Note: Included in ASCE/SEI 25.)

ANSI Z21.71—8193 (R2007) Automatic Intermittent Pilot Ignition Systems for Field Installation, with Addenda, Z21.71a—85 and Z21.71b—89

ANSI Z21.101/CSA 8.5—12 Gas Hose Connectors for Portable and Moveable Gas Appliances

UL 144—857th Edition Pressure Regulating Valves for LP-Gas

UL 441—9606 (R2010) Gas Vents

Equipment


ANSI Z21.1—9610 Household Cooking Gas Appliance

ANSI Z21.5.1—9506 (R2012) Gas Clothes Dryers, Volume I, Type 1 Clothes Dryers

ANSI Z21.5.2—9513 Gas Clothes Dryers, Volume II, Type 2 Clothes Dryers

ANSI Z21.10.1—9814 Gas Water Heaters, Volume I, Storage Water Heaters with Input Ratings of 75,000 Btu Per Hour or Less

ANSI Z21.10.3—9814 Gas Water Heaters, Volume III, Storage with Input Ratings Above 75,000 Btu Per Hour Circulating and Instantaneous Water Heaters

ANSI Z21.11.1—91 Gas-Fired Room Heaters, Volume I, Vented Room Heaters

ANSI Z21.11.2—9613 Gas-Fired Room Heaters, Volume II, Unvented Room Heaters

ANSI Z21.13—9114 Gas-Fired Low-Pressure Steam and Hot Water Boilers

ANSI Z21.19—9014 Refrigerators Using Gas Fuel, with Addenda Z21.19a-92

ANSI Z21.40.1—96 (R2012) Gas-Fired, Absorption Summer Air Conditioning AppliancesHeat Activated Air Conditioning and Heat Pump Appliances

ANSI Z21.42—9313 Gas-Fired Illuminating Appliances

ANSI Z21.44—9194 (Withdrawn) Gas-Fired Gravity and Fan Fan-Type Direct Vent Wall Furnaces, with Addenda, Z21.44a—92

ANSI Z21.47—9312 Gas-Fired Central Furnaces (Except Direct Vent Central Furnaces)

ANSI Z21.48—92 Gas-Fired Gravity and Fan Type Floor Furnace

ANSI Z21.49—92 Gas-Fired Gravity and Fan Type Vented Wall Furnaces

ANSI Z21.50—9614 Vented Decorative Gas Appliances Fireplaces

ANSI Z21.56—9414 Gas-Fired Pool Heaters

ANSI Z21.58—9507 Outdoor Cooking Gas Appliances

ANSI Z21.60—9612 Decorative Gas Appliances for Installation in Solid-Fuel Burning Appliances

ANSI Z21.61—83 (R2004) Gas-Fired Toilets

ANSI Z21.64—90 Direct Vent Central Furnaces (Note: included in Z21.47-12)

ANSI Z21.86—08 Vented Gas-Fired Space Heating Appliances

ANSI Z21.88—14 Vented Gas Fireplace Heaters

ANSI Z83.4—9113 Non-Recirculating Direct Gas-Fired Make-Up Air HeatersIndustrial Heaters

ANSI Z83.6—90 Gas-Fired Infrared Heaters (Note: included in ANSI Z21.88-14)

ANSI Z83.8—9613 Gas Unit Heaters, Gas Packaged Heaters, Gas Utility Heaters and Gas-Fired Duct Furnaces

ANSI Z83.9—90 Gas-Fired Duct Furnaces (Note: included in ANSI Z83.8-13

ANSI Z83.11—9606 (R2012) Gas Food Service Equipment-Ranges and Unit Broilers, with Addenda, Z83.11a—97 and Z83.11b—91

ANSI Z83.12—89 Gas Food Service Equipment-Baking and Roasting Ovens, with Addenda,


Z83.12a—90 and Z83.12b—91

ANSI Z83.13—89 Gas Food Service Equipment-Deep Fat Fryers, with Addenda, Z83.13a—90 and Z83.13b—91

ANSI Z83.14—89 Gas Food Service Equipment-Counter Appliances, with Addenda, Z83.14a—90 and Z83.14b—91

ANSI Z83.15—89 Gas Food Service Equipment-Kettles, Steam Cookers and Steam Generators, with Addenda, Z83.15a—90 and Z83.15b—91

ANSI Z83.16—82 Gas-Fired Unvented Commercial and Industrial Heaters, with Addenda, Z83.16a—84 and Z83.16b—89

ANSI Z83.18—9012 Recirculating Direct Gas-Fired Industrial Air Heaters, with Addenda, Z83.18a—91

UL 391—8910 Solid-Fuel and Combination Fuel Control Central and Supplementary Furnaces

UL 795—9511 Commercial-Industrial Gas Heating Equipment

SECTION 1102

ORGANIZATIONS

The purpose of this reference index is to catalog, by name and address, those agencies, associations, institutions and others that are referred to in this Code by name, initials or symbols. Further, there are those listed, for convenience, whose technical and other services are made available to the Chief Mechanical Inspector. ACCA Air-Conditioning Contractors of America

2800 Shirlington Road Suite 300 Arlington, VA 22206 www.acca.org

AGA American Gas Association 400 North Capitol Street NW Suite 450 Washington, DC 20001 www.aga.org

AHRI Air-Conditioning, Heating and Refrigeration Institute [Formerly Air-Conditioning and Refrigeration Institute (ARI)] 2111 Wilson Boulevard Suite 500 Arlington, VA 22201 www.ahrinet.org

ANSI American National Standards Institute 25 West 43rd Street 4th Floor New York, NY 10036 www.ansi.org

API American Petroleum Institute 1220 L Street, NW Washington, D.C. 20005 www.api.org

ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers 1791 Tullie Circle NE Atlanta, GA 30329 www.ashrae.org

ASME American Society of Mechanical Engineers Three Park Avenue New York, NY 10016 www.asme.org


ASTM American Society for Testing and Materials 100 Barr Harbor Drive West Conshohocken, PA 19428 www.astm.org

AWWA American Water Works Association 6666 West Quincy Avenue Denver, CO 80235 www.awwa.org

HUD US Department of Housing and Urban Development 451 7th Street, SW Washington, DC 20410

GAMA Gas Appliance Manufacturers Association [Formerly The Hydronics Institute (HYDI)] 2107 Wilson Boulevard Suite 600 Arlington, VA 22201 www.gamanet.org

ICC International Code Council 500 New Jersey Avenue NW 6th Floor Washington, DC 20001 www.iccsafe.org

MSS Manufacturers Standardization Society of the Valve and Fittings Industry 127 Park Street NE Vienna, VA 22180 www.mss-hq.com

NACE National Association of Corrosion Engineers International 1440 South Creek Drive Houston, TX 77084 www.nace.org

NFPA National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169 www.nfpa.org

UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, IL 60062 www.ul.com

EPCOT Mechanical Code 1

CHAPTER 16


This Chapter lists the standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title, and the section or sections of this document that reference the standard.

ACCA

Air-Conditioning Contractors of America 2800 Shirlington Road Suite 300 Arlington, VA 22206



section number

Manual D Residential Duct Systems, Second Edition 602

Manual J Residential Load Calculation, Eighth Edition A-102

Manual N Commercial Load Calculation, Fifth Edition A-102

Manual Q Commercial Low-Pressure, Low-Velocity Duct System Design, First Edition

602

ACGIH

American Conference on Governmental Industrial Hygienists 1330 Kemper Meadow Drive Cincinnati, OH 45240



section number

ACGIH Manual Industrial Ventilation: A Manual of Recommended Practice for Design, 27th Edition

Chapter 17

ADC

Air Diffusion Council 1901 North Roselle Road Suite 800 Schaumburg, IL 60195



section number

Flexible Duct Performance and Installation Standards, Fifth Edition 602, Appendix B

ANSI

American National Standards Institute 25 West 43rd Street 4th Floor New York, NY 10036



section number

ASHRAE 15—0113 Safety Code for Mechanical Refrigeration 302.3, 1101.2, 1107.2.1, 1107.2.2

ASHRAE 34—0413 Number Designation and Safety Classification of Refrigerants 1101.7, Table 1102, 1102.1

ASME B31.9—0814 Building Services Piping Table 1203

AWS A2.4-0712 Standard Symbols for Welding, Brazing and Non-Destructive Examination

Chapter 17

AWS A3.0/A3.0M—10 Standard Welding Terms and Definitions, Including Terms for Adhesive Bonding, Brazing, Soldering, Thermal Cutting and Thermal Spraying

Chapter 17

AWS B1.10/B1.10M—09 Guide for the Non-Destructive Examination of Welds Chapter 17

AWS B2.1/B2.1M—09 Specification for Welding Procedure and Performance Qualification Chapter 17


AWS C5.2—01 Recommended Practices for Plasma Arc Cutting and Gouging Chapter 17

AWS C5.4—93 Recommended Practices for Stud Welding Chapter 17

AWS C5.5/C5.5M—03 Recommended Practices for Gas Tungsten Arc Welding Chapter 17

AWS C5.6—89R Recommended Practice for Gas Metal Arc Welding Chapter 17

AWS C5.7—00(R2006) Recommended Practices for Electro-Gas Welding Chapter 17

AWS D10.7/D10.7M—08 Guide for the Gas-Shielded Arc Welding of Aluminum and Aluminum-Alloy Pipe

Chapter 17

AWS D10.11/D10.11M—07 Guide for Root-Pass Welding of Pipe without Backing Chapter 17

B31.1—9514 Power and Process Piping Package Chapter 17

B36.10M—04 Welded and Seamless Wrought-Steel Pipe 1201.4.1, 1402.1.2

B73.1—0712 Horizontal End Suction Centrifugal Pumps for Chemical Process 1201.2.1

B77.1—9511/B77.1a—12 Passenger Ropeways—Aerial Tramways, Aerial Lifts, Surface Lifts, Tows and Conveyors—Safety Requirements

Chapter 17

C50.11—65 Synchronous Motors (Withdrawn) 1201.2.2

Z21.13—1014 Gas-Fired, Low-Pressure Steam and Hot Water Boilers 1001.2

Z21.59—74 Gas-Fired, High-Pressure Steam and Hot Water Boilers, Second Edition (Withdrawn)

1001.2

ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers 1791 Tullie Circle NE Atlanta, GA 30329



section number

62.1—0413 Ventilation for Acceptable Indoor Air Quality 402

ASHRAE—0412 Handbook, HVAC Systems and Equipment 302.3, 602

ASHRAE—0513 Handbook, Fundamentals 1106.1.1, A-102

ASHRAE—0711 Handbook, HVAC Applications, Chapter 30, Solar Energy Utilization 1501.6




section number

ASME—0413 Boiler and Pressure Vessel Code: Section I, Power Boilers; Section IV, Heating Boilers; and Section IX, Welding and Brazing Qualifications

1001.2, 1003.2, 1701.3

B1.20.1—83(R2001)13 Pipe Threads 1203.12.1




section number

A 53/A 53M—0212 Specification for Pipe, Steel, Black and Hot-Dipped Zinc-Coated Welded and Seamless

Table 1203, Table 1204

B 42—02e0110 Specification for Seamless Copper Pipe, Standard Sizes 1106.2.3, Table 1203

B 43—0414 Specification for Seamless Red Brass Pipe, Standard Sizes 1106.2.3, Table 1203

B 88—0314 Specification for Seamless Copper Water Tube 1106.2.4, Table 1203, Table 1204


B 280—0313 Specification for Seamless Copper Water Tube for Air-Conditioning and Refrigeration Field Service

1106.2.5

B 813—00e0110 Standard Specification for Liquid and Paste Fluxes for Soldering Application of Copper and Copper-Alloy Tubes

1203.3

B 828—0210 Standard Practice for Making Capillary Joints by Soldering of Copper and Copper-Alloy Tube and Fittings

1203.3

C 177—1013 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded Hot-Plate Apparatus

Appendix B

C 315—02 11 Clay Flue Linings Figure 813A

C 411—9711 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation

605, 1506.5

C 518—10 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

Appendix B

D 1693—0113 Test Method for Environmental Stress-Cracking of Ethylene Plastics Table 1206.2A

D 1785—0412 Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

Table 1204

D 2104—0301 Specification for Polyethylene (PE) Plastic Pipe, Schedule 40 (Withdrawn)

Table 1204

D 2239—0312a Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR), Based on Controlled Inside Diameter

Table 1204

D 2241—04a09 Specification for Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)

Table 1204

D 2513—04a14e1 Specification for Thermoplastic Gas Pressure Pipe Tubing and Fittings Table 1206.2A

D 2581—09 Specification for Polybutylene (PB) Plastics Molding and Extrusion Materials

Table 1206.2A

D 2662—96 Specification for Polybutylene (PB) Plastic Tubing (Withdrawn) Table 1204

D 2666—96 Specification for Polybutylene (PB) Plastic Tubing (Withdrawn) Table 1204

D 2683—9814 Specification for Socket-Type Polyethylene Fittings for Outside-Diameter-Controlled Polyethylene Pipe and Tubing

Table 1206.2B

D 3000—95 Specification for Polybutylene (PB) Plastic Pipe (SDR-PR) Based on Outside Diameter (Withdrawn)

Table 1204

D 3261—0312e1 Specification for Butt Heat-Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

Table 1206.2B

D 3309—96a(2002) Specification for Polybutylene (PB) Plastic Hot Water Distribution Systems

Table 1203, Table 1204

D 3350—02a14 Specification for Polyethylene Plastics Pipe and Fittings Materials Table 1206.2A

D 3667—8505(2010) Specification for Rubber Seals Used in Flat-Plate Solar Collectors 1505.2

D 3771—03(2007) Specification for Rubber Seals Used in Concentrating Solar Collectors 1505.2

D 3832—79(2011) Specification for Rubber Seals Contacting Liquids in Solar Energy Systems

1505.2

E 84—0414 Test Method for Surface-Burning Characteristics of Building Materials 202, 307.1, 1506.4, 1507.2

E 136—0412 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

202

F 714—1013 Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

Table 1206.2A

AWS American Welding Society 550 NW LeJeune Road Miami, FL 33126



section number

D9.1M/D9.1—0612 Sheet Metal Welding Code 604.1.1.1





section number

EPCOT Building Code—2009 2015 Edition 101.1, 101.4.2, 102.2, 104.4, 201.3, 202, 301.3.1,

301.4.1, 303.6.1, 303.7.1, 401.4, 403.1, 405.4, 407.2,

504.8, 605.1.8, 608.2.2.1, Table 810, 903.3.6,

904.5.1, 1006.2, 1102.2, 1103.2, 1104.2.1, 1105.4.2,

1201.3.1, 1501.4, 1501.5, 1504.2, 1504.3

EPCOT Fire Prevention Code—2009 2015 Edition 201.3

EPCOT Energy Efficiency Code for Building Construction—2009 2015 Edition

A-101

EPCOT Fuel Gas Code—2009 2015 Edition 101.1, 101.4.4, 102.2, 201.3, 301.6, 801.7,

813.11, 814.1, 904.9.6, 1101.6, 1302, 1303,

1401.2.3

EPCOT Plumbing Code—2009 2015 Edition 101.1, 101.4.6, 102.2, 105.6, 201.3, 510.2,

608.1.1, 1001.3, 1101.5, 1201.3.2, 1201.4.1,

1201.4.2, 1203.11, 1508.2, 1511.3.2, 1511.4, 1511.5, 1511.8, 1511.10, 1512.1,

1512.2, 1513.1

M-1 Industrial Ventilation Manual 1701.1

M-2 Aerial Passenger Tramways 1701.1, 1701.3(d)

M-3 Gas Piping 1701.1

M-4 Power Piping 1701.1

M-5 Welding Standards 1701.1

M-6 Boiler and Pressure Vessel Code, Division 1 1701.1

HYDI The Hydronics Institute 2107 Wilson Boulevard Suite 600 Arlington, VA 22201



section number

C-30—84 Cooling Load Calculation Guide A-102

H-22—98 Heat Loss Calculation Guide A-102

NAIMA North American Insulation Manufacturers Association 44 Canal Center Plaza Suite 310 Alexandria, VA 22314



section number

AH 116—02 Fibrous Glass Duct Construction Standards, Second Edition 602

AH 124—02 Fibrous Glass Duct Liner Standard, First Edition 602





section number

12—0815 Carbon Dioxide Extinguishing Systems 506.3

13—0213 Installation of Sprinkler Systems 506.3

16—0715 Installation of Foam-Water Sprinkler and Foam-Water Spray Systems 506.3

17—0209 Dry-Chemical Extinguishing Systems 506.3

17A—0209 Wet-Chemical Extinguishing Systems 506.3

31—0111 Installation of Oil-Burning Equipment 814.2

70—0811 National Electrical Code 101.1, 101.4.3, 102.2, 308.1, 403.2, Table 1103A,

1105.6, 1105.7

72—0710 National Fire Alarm Code 405.1

82—0409 Incinerators Waste- and Linen-Handling Systems and Equipment 601.3, 904.2

90A—0215 Installation of Air-Conditioning and Ventilating Systems 302.3

90B—0615 Installation of Warm-Air Heating and Air-Conditioning Systems 302.3

91—0410 Exhaust Systems for Air Conveying of Vapors, Gases, Mists and Noncombustible Particulate Solids

509.1

96—0408 Ventilation Control and Fire Protection of Commercial Cooking Operations

506.3

214—0511 Water-Cooling Towers 302.3

SMACNA Sheet Metal and Air-Conditioning Contractors National Association 4201 Lafayette Center Drive Chantilly, VA 20151



section number

SMACNA—0310 Fibrous Glass Duct Construction Standards 602

SMACNA—9505 HVAC Duct Construction Standards, --Metal and Flexible, First Edition 602

UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, IL 60062



section number

103—0110 Factory-Built Chimneys 803.2, Table 810

127—9605 Factory-Built Fireplaces 803.3, 903.1

181—96(R-98)13 Factory-Made Air Ducts and Air Connectors, Seventh Edition 602, 603.2, 608.1.2

181A—0513 Closure Systems For Use with Rigid Air Ducts and Air Connectors, Parts I, II and III, Second Edition

602

181B—0513 Closure Systems For Use with Flexible Air Ducts and Air Connectors, Parts I and II

602

555—9906 Fire Dampers 202, 609.1.1

555S—9914 Leakage-Rated Dampers for Use in Smoke Control Systems 202

737—9611 Fireplace Stoves 903.2


910—98 Test Method for Flame-Propagation and Smoke-Density Values for Electrical and Optical-Fiber Cables Used in Spaces Transporting Environmental Air (Withdrawn)

608.1.2

1482—9811 Room Heaters, Solid-Fuel Type 903.2

1777—0407 Chimney Liners 805.2.6, 805.4, 806.4

SECTION 1601

ORGANIZATIONS

The purpose of this reference index is to catalog, by name and address, those agencies, associations, institutions and others that are referred to in this Code by name, initials or symbols. Further, there are those listed, for convenience, whose technical and other services are made available to the Chief Mechanical Inspector. ACCA Air-Conditioning Contractors of America

2800 Shirlington Road Suite 300 Arlington, VA 22206 www.acca.org

ACGIH American Conference of Governmental Industrial Hygienists 1330 Kemper Meadow Drive Cincinnati, OH 45240 www.acgih.org

ADC Air Diffusion Council 1901 North Roselle Road Suite 800 Schaumburg, IL 60195 www.flexibleduct.org

AGA American Gas Association 400 North Capitol Street NW Suite 450 Washington, DC 20001 www.aga.org

AHRI Air-Conditioning, Heating and Refrigeration Institute (Formerly ARI) 2111 Wilson Boulevard Suite 500 Arlington, VA 22201 www.ahrinet.org

AISI American Iron and Steel Institute 1140 Connecticut Avenue NW Suite 705 Washington, DC 20036 www.steel.org


ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers 1791 Tullie Circle NE Atlanta, GA 30329 www.ashrae.org



ASSE American Society of Sanitary Engineering 901 Canterbury Suite A Westlake, OH 44145 www.asse-plumbing.org


AWS American Welding Society 550 NW LeJeune Road Miami, FL 33126 www.aws.org

CDA Copper Development Association 260 Madison Avenue 16th Floor New York, NY 10016 www.copper.org

CISPI Cast Iron Soil Pipe Institute 1064 Delaware Avenue SE Atlanta, GA 30316 www.cispi.org

FM Factory Mutual Engineering Division Standards-Laboratories Department 1151 Boston-Providence Turnpike P.O. Box 9102 Norwood, MA 02062 www.fmglobal.com

FS Federal Specifications U.S. General Services Administration One Constitution Square 1275 First Street NE Washington, DC 20417 www.gsa.gov

GAMA Gas Appliance Manufacturers Association [Formerly The Hydronics Institute (HYDI)] 2107 Wilson Boulevard Suite 600 Arlington, VA 22201 www.gamanet.org

ICC International Code Council 500 New Jersey Avenue NW 6th Floor Washington, DC 20001 www.iccsafe.org

MSS Manufacturers Standardization Society of the Valve and Fittings Industry 127 Park Street NE Vienna, VA 22180 www.mss-hq.com

NAIMA North American Insulation Manufacturers Association 44 Canal Center Plaza Suite 310 Alexandria, VA 22314 www.naima.org



NIST National Institute of Standards and Technology [Formerly National Bureau of Standards (NBS)] 100 Bureau Drive Stop 1970 Gaithersburg, MD 20899 www.nist.gov

NPGA National Propane Gas Association 1899 L Street NW Suite 350 Washington, DC 20036 www.npga.com

NSF NSF International 789 North Dixboro Road PO Box 130140 Ann Arbor, MI 48113 www.nsf.org

PPI Plastics Pipe Institute 105 Decker Court Suite 825 Irving, TX 75062 www.plasticpipe.org

SGA Southern Gas Association 3030 LBJ Freeway Suite 1300 Dallas, TX 75234 www.southerngas.org

SMACNA Sheet Metal and Air-Conditioning Contractors National Association 4201 Lafayette Center Drive Chantilly, VA 20151 www.smacna.org

UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, IL 60062 www.ul.com

EPCOT Plumbing Code 1

CHAPTER 14


This Chapter lists the standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title, and the section or sections of this document that reference the standard. The application of the referenced standards shall be as specified in Subsection 102.8.

ANSI

American National Standards Institute 25 West 43rd Street 4th Floor New York, NY 10036

Standard Reference number Title

Referenced in code

section number

A118.10—99 Load Bearing, Bonded, Waterproof Membranes for Thin Set Ceramic Tile and Dimension Stone Installation

417.5.7

Z4.3—95(R2005) Minimum Requirements for Non-Sewered Waste-Disposal Systems 311.1

Z21.22—99(R2003R2014) Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems— with 1990 Addendum

504.2, 504.5

Z124.1—95 Plastic Bathtub Units (Note: Included in Z124.1.2) 407.1

Z124.1.2—9505 Plastic Shower Receptors and Shower StallsBathtub and Shower Units 407.1, 417.1

Z124.3—9505 Plastic LavatoriesLavatory Units 416.1, 416.2

Z124.4—9606 Plastic Water Closet Bowls and Tanks 420.1

Z124.6—9707 Plastic Sinks 415.1, 418.1

AHRI Air-Conditioning, Heating and Refrigeration Institute 2111 Wilson Boulevard Suite 500 Arlington, VA 22201


Referenced in code

section number

1010—9402 Self-Contained, Mechanically Refrigerated Drinking-Water Coolers (Withdrawn)

410.1



Referenced in code

section number

A13.1—9607 Scheme for the Identification of Piping Systems 608.8

A112.1.2—0412 Air Gaps in Plumbing Systems 608.1

A112.6.1M—97(R2002R2012) Supports for Off-the-Floor Plumbing Fixtures for Public Use 405.4.3

A112.6.9—05 Siphonic Roof Drains 1112.1

A112.14.1—03(R2012) Backwater Valves 715.3

A112.18.1M—0305/CSA B125.1—05

Brass Plumbing Fixture Units—with 1995 ErrataPlumbing Supply Fittings

424.1, 424.5, 424.7

A112.18.3—02(R2008) Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

424.7

A112.19.1M—9913 Enameled Cast-Iron and Enameled Steel Plumbing Fixtures 407.1, 410.1, 415.1, 416.1, 418.1

A112.19.2—0308/CSA B45.1—08

Vitreous ChinaCeramic Plumbing Fixtures—with 1996 Errata 405.9, 408.1, 410.1, 416.1, 418.1, 419.1, 420.1, 407.1, 409.1, 410.1, 415.1, 416.1, 417.1, 418.1, 420.1


A112.19.3—0008/CSA B45.4—08

Stainless Steel Plumbing Fixtures (Designed for Residential Use) 415.1, 416.1, 418.1, 420.1

A112.19.4M—99 Porcelain-Enameled-Formed Steel Plumbing Fixtures 407.1, 416.1, 418.1

A112.19.5—9911 Flush Valves and Spuds for Water Closets, Urinals, and Tanks (with Update No. 1)Trim for Water Closet Bowls, Tanks and Urinals

425.4

A112.19.6—95 Hydraulic Performance Requirements for Water Closets and Urinals 419.1, 420.1

A112.19.7—9512/CSA B45.10—12

Whirlpool Bathtub AppliancesHydromassage Bathtub Systems 421.1

A112.19.8—9607 Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, Hot Tubs and Whirlpool Bathtub Appliances

421.4

A112.19.9—98(R2002)/A112.19.9M—91(R2002)

Non-Vitreous Ceramic Plumbing Fixtures 407.1, 409.1, 410.1, 415.1, 416.1, 417.1,

418.1, 420.1

A112.21.1—98A112.6.3—01(R2007)

Floor and Trench Drains 412.1

A112.21.2—836.4—12 Roof, Deck and Balcony Drains 1102.6

B1.20.1—99(R2003)13 Pipe Threads, General Purpose (inch) 605.10.3, 605.12.3, 605.14.4, 605.16.3, 605.17.1, 605.20.3,

705.2.3, 705.4.3, 705.7.4, 705.10.1,

705.12.1

B16.3—9811 Malleable-Iron-Threaded Fittings Table 605.6, Table 702.4, Table 1102.7

B16.4—9811 Cast-Iron-Threaded Fittings Table 605.6, Table 702.4, Table 1102.7

B16.9—03 Factory-Made Wrought Steel Buttwelding Fittings Table 605.6, Table702.4, Table

1102.7, Table 605.6, Table 702.4, Table

1102.7

B16.11—0111 Forged Steel Fittings, Socket-Welding and Threaded Table 605.6, Table 702.4, Table 1102.7

B16.12—9809(R2014) Cast-Iron-Threaded Drainage Fittings Table 605.6, Table 702.4, Table 1102.7

B16.15—9413 Cast-Bronze-Threaded Fittings Table 605.6, Table 702.4, Table 1102.7

B16.18—0112 Cast-Copper-Alloy Solder Joint Pressure Fittings Table 605.6, Table 702.4, Table 1102.7

B16.22—0113 Wrought-Copper and Copper-Alloy Solder Joint Pressure Fittings Table 605.6, Table 702.4, Table 1102.7

B16.23—0213 Cast-Copper-Alloy Solder Joint Drainage Fittings (DWV)—with

1994 Errata Table 605.6, Table

702.4, Table 1102.7

B16.26—8813 Cast-Copper-Alloy Fittings for Flared Copper Tubes Table 605.6, Table 702.4, Table 1102.7

B16.28—949--12 Factory-Made Wrought Steel Buttwelding Short Radius Elbows

and ReturnsFittings Table 605.6, Table

702.4, Table 1102.7

B16.29—0112 Wrought-Copper and Wrought-Copper-Alloy Solder Joint Drainage Fittings—DWV

Table 605.6, Table 702.4, Table 1102.7

B16.32—92 Cast-Copper-Alloy Solder Joint Fittings for Sovent Drainage Systems Table 605.6, Table 702.4, Table 1102.7

B36.10—04(R2010) Welding and Seamless Wrought Steel Pipe 1304.6.3

ASPE American Society of Plumbing Engineers 8614 Catalpa Avenue Suite 1007 Chicago, IL 60656


Referenced in code

section number

45—07 Siphonic Roof Drainage Systems 1112.1


ASSE American Society of Sanitary Engineering 901 Canterbury Suite A Westlake, OH 44145


Referenced in code

section number

1001—02 Performance Requirements for Pipe-Applied Atmospheric-Type Vacuum Breakers

425.2, Table 608.1, 608.13.6

1002—9908 Performance Requirements for Water Closet Flush Tank Ball Cocks 425.3.1, Table 608.1

1003—0109 Performance Requirements for Water Pressure-Reducing Valves for Domestic Water Supply Systems

604.8

1004—9008 Performance Requirements for Commercial Dishwashing Machines 409.1

1005—99 Performance Requirements for Water Heater Drain Valves—with 1986 Revision

501.3

1006—89 Performance Requirements for Residential Use (Household) Dishwashers

409.1

1007—92 Performance Requirements for Home Laundry Equipment 406.1, 406.2

1008—8906 Performance Requirements for Household Food Waste Disposer Units 413.1

1009—90 Performance Requirements for Commercial Food Waste Grinder Units 413.1

1010—9604 Performance Requirements for Water Hammer Arresters—with 1982 Revision

604.9

1011—9304 Performance Requirements for Hose Connection Vacuum Breakers Table 608.1, 608.13.6

1012—0209 Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent

Table 608.1, 608.13.3, 608.16.1,

608.16.2

1013—9909 Performance Requirements for Reduced Pressure Principle Backflow Preventers

Table 608.1, 608.13.2, 608.16.2

1014—9005 Performance Requirements for Hand-Held Showers 424.3

1015—9909 Performance Requirements for Double Check Backflow Prevention Assembly—with 1993 Revision

Table 608.1, 608.13.7

1016—9605 Performance Requirements for Individual Thermostatic, Pressure Balancing and Combination Control Valves for Bathing Facilities

424.4

1018—01 Performance Requirements for Trap Seal Primer Valves; Water Supply Fed—with 1986 Revision

1002.4

1019—9711 Performance Requirements for Wall Hydrants, Freezeless, Automatic-Draining, Anti-Backflow Types

Table 608.1, 608.13.6

1020—9804 Performance Requirements for Pressure Vacuum Breaker Assembly Table 608.1, 608.13.5

1024—04 Performance Requirements for Dual Check-Valve-Type Backflow Preventers (for Residential Supply Service or Individual Outlets)

Table 608.1

1025—78 Performance Requirements for Diverters for Plumbing Faucets with Hose Spray, Anti-Siphon-Type, Residential Applications

424.2

1032—04(R2011) Performance Requirements for Dual Check-Valve-Type Backflow Preventers for Carbonated Beverage Dispensers—Post-Mix Types

Table 608.1, 608.16.1

1035—0208 Performance Requirements for Laboratory Faucet Backflow Preventers Table 608.1, 608.13.6

1037—90 Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

425.2

1044—01 Performance Requirements for Trap Seal Primer Valves; Drainage Type

1002

1047—9911 Performance Requirements for Reduced Pressure Detector Assembly Backflow Preventers

Table 608.1

1048—9911 Performance Requirements for Double Check Detector Assembly Backflow Preventer

Table 608.1, 608.13.7

1049—09 Performance Requirements for Individual and Branch Type Air Admittance Valves for Chemical Waste Systems

917.8

1050—09 Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems

917.1

1051—0209 Performance Requirements for Air Admittance Valves for Plumbing Drainage Systems, Fixture and Branch Devices

917.1

1052—9304 Performance Requirements for Hose Connection Backflow Preventers Table 608.1, 608.13.6


1056—0113 Backsiphonage Vacuum Breaker Table 608.1, 608.13.8

1069—05 Performance Requirements for Automatic Temperature Control Mixing Valves

424.5

1070—04 Performance Requirements for Water-Temperature Limiting Devices 408.3

5010-1013-1—9909 Field Test Procedure for a Reduced Pressure Principle Assembly Using a Differential Pressure Gauge—with August 1992 Revisions

312.9

5010-1015-1—9809 Field Test Procedure for a Double Check-Valve Assembly Using a Duplex Gauge—with August 1992 Revisions

312.9

5010-1015-2—9909 Field Test Procedure for a Double Check-Valve Assembly Using a Differential Pressure Gauge—High- and Low-Pressure Hose Method—with August 1992 Revisions

312.9

5010-1015-3—9109 Field Test Procedure for a Double Check-Valve Assembly Using a Differential Pressure Gauge—High-Pressure Hose Method—with August 1992 Revisions

312.9

5010-1015-4—9109 Field Test Procedure for a Double Check-Valve Assembly Using a Sight Tube —with August 1992 Revisions

312.9

5010-1020-1—9109 Field Test Procedure for a Pressure Vacuum Breaker Assembly 312.9

5010-1047-1—9109 Field Test Procedure for a Reduced Pressure Detector Assembly Using a Differential Pressure Gauge—with August 1992 Revisions

312.9

5010-1048-1—9109 Field Test Procedure for a Double Check Detector Assembly Using a Duplex Gauge—with August 1992 Revisions

312.9

5010-1048-2—9109 Field Test Procedure for a Double Check Detector Assembly Using a Differential Pressure Gauge—High- and Low-Pressure Hose Method—with August 1992 Revisions

312.9

5010-1048-3—9109 Field Test Procedure for a Double Check Detector Assembly Using a Differential Pressure Gauge—High-Pressure Hose Method—with August 1992 Revisions

312.9

5010-1048-4—9109 Field Test Procedure for a Double Check Detector Assembly Using a Sight Tube—with August 1992 Revisions

312.9



Referenced in code

section number

A 53—0212 Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless


A 74—0413 Specification for Cast-Iron Soil Pipe and Fittings Table 702.1, Table 702.2, Table 702.3, Table 702.4, 708.2,

Table 1102.4, Table 1102.5

A 106/A 106M—1014 Specification for Seamless Carbon Steel Pipe for High-Temperature Service

1304.6.3

A 733—0313 Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples

Table 605.8

A 888—04a13 Specification for Hubless Cast-Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Application

Table 702.1, Table 702.2, Table 702.3, Table 702.4, Table

1102.4, Table 1102.5, Table 1102.7

B 32—0308(2014) Specification for Solder Metal 605.14.3, 605.15.4, 705.7.3, 705.8.3

B 42—02e0110 Specification for Seamless Copper Pipe, Standard Sizes Table 605.4, Table 605.5, Table 702.1

B 43—0414 Specification for Seamless Red Brass Pipe, Standard Sizes Table 605.4, Table 605.5, Table 702.1

B 75—0211 Specification for Seamless Copper Tube Table 605.4, Table 605.5, Table 702.1, Table 702.2, Table

702.3, Table 1102.4

B 88—0314 Specification for Seamless Copper Water Tube Table 605.4, Table 605.5, Table 702.1, Table 702.2, Table


702.3, Table 1102.4

B 152—0013 Specification for Copper Sheet, Strip Plate and Rolled Bar 402.3, 425.3.3, 902.2

B 251—02e0110 Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube


702.3, Table 1102.4

B 302—0212 Specification for Threadless Copper Pipe Table 605.4, Table 605.5, Table 702.1

B 306—0213 Specification for Copper Drainage Tube (DWV) Table 702.1, Table 1102.4

B 447—0212 Specification for Welded Copper Tube Table 605.4, Table 605.5

B 687—99(2011) Specification for Brass, Copper and Chromium-Plated Pipe Nipples Table 605.8

B 813—00e0110 Standard Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper-Alloy Tube

605.14.3, 605.15.4, 705.7.3, 705.8.3

B 828—02(2010) Practice for Making Capillary Joints by Soldering of Copper and Copper-Alloy Tube and Fittings

605.14.3, 605.15.4, 705.7.3, 705.8.3

C 4—0304(2014) Specification for Clay Drain Tile Table 702.3, Table 1102.4, Table 1102.5

C 14—0311 Specification for Concrete Sewer, Storm Drain and Culvert Pipe Table 702.3, Table 1102.4

C 76—0414 Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

Table 702.3, Table 1102.4

C 425—04(2013) Specification for Compression Joints for Vitrified Clay Pipe and Fittings 705.13, 705.14

C 428—0205(2011) Specification for Asbestos-Cement Non-Pressure Sewer Pipe Table 702.2, Table 702.3

C 443—0312 Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets

705.6, 705.14

C 564—04a14 Specification for Rubber Gaskets for Cast-Iron Soil Pipe and Fittings 705.5.2, 705.5.3, 705.14

C 700—0213 Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength and Perforated


C 1053—00(2010) Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste and Vent (DWV) Applications


D 1527—99(2005) Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

Table 605.4

D 1785—0412 Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

Table 605.4

(Note: ASTM D 1861—88 has been discontinued and has not been replaced by ASTM.)


D 2235—0104(2011) Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

605.10.2, 705.2.2

D 2239—0312 Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Table 605.4

D 2241—04a09 Specification for Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR-Series)

Table 605.4

D 2282—99e199(2005) Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

Table 605.4


D 2464—9913 Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80


D 2466—0213 Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40


D 2467—0413 Specification for Socket-Type Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80


D 2468—96a Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40


D 2564—0212 Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

605.20.2, 705.12.2


D 2609—0214 Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe


D 2657—9707 Standard Practice for Heat-Joining Polyolefin Pipe and Fittings 605.18.2, 605.19.2

D 2661—0214 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40Plastic Drain, Waste and Vent Pipe and Fittings

Table 702.1, Table 702.2, Table 702.3,

705.2.2, Table 1102.4

D 2662—96a Specification for Polybutylene (PB) Plastic Pipe (SDR-PR) Table 605.4

D 2665—04ae0114 Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste and Vent Pipe and Fittings


Table 1102.4

D 2666—96a Specification for Polybutylene (PB) Plastic Tubing Table 605.4

D 2672—0396a(2009) Specification for Joints for IPS PVC Pipe Using Solvent Cement Table 605.4

D 2729—96a11 Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings Table 1102.4

D 2737—0312 Specification for Polyethylene (PE) Plastic Tubing Table 605.4

D 2751—96a05 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings


D 2846—9914 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems

Table 605.4, Table 605.6, 605.16.2

D 2855—02 Standard Practice for Making Solvent-Cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings

605.20.2, 705.12.2

D 2949—01a10 Specification for 3.25-Inch Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste and Vent Pipe and Fittings


D 3034—0414 Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings


D 3139—98(2011) Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

605.10.1, 605.20.1

D 3212—0307(2013) Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

705.2.1, 705.12.1

D 3309—97a(2002) Specification for Polybutylene (PB) Plastic Hot Water Distribution Systems

Table 605.4, Table 605.5, 605.18.2,

605.18.3

D 3311—0211 Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns Table 702.4

D 4551—96(2001)12 Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane

417.5.3

F 405—9713 Specification for Corrugated Polyethylene (PE) Tubing and Fittings Table 1102.5

F 409—0212 Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings


F 437—9909 Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80


F 438—0409 Specification for Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40


F 439—02e0113 Specification for Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule


F 441—0213 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80


F 442—9913 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)


F 477—02e0114 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe 605.21, 705.14

F 493—0414 Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

605.16.2

F 628—0112 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste and Vent Pipe with a Cellular Core


705.2.2, Table 1102.4

F 656—0210 Specification for Primers for Use in Solvent-Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

705.12.2

F 876—0413 Specification for Cross-Linked Polyethylene (PEX) Tubing Table 605.4

F 877—02e0111 Specification for Cross-Linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems


F 891—00e0110 Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core


Table 1102.4, Table


1102.5

F 1281—0311 Specification for Cross-Linked Polyethylene/Aluminum/Cross-Linked Polyethylene (PEX-AL-PEX) Pressure Pipe


F 1282—0310 Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

Table 605.4

F 1412—09 Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

917.8

F 1488—0309 Standard Specification for Coextruded Composite Pipe Table 702.1, Table 702.2, Table 702.3

F 1807—0414 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring SDR 9 Cross-Linked Polyethylene (PEX) Tubing

Table 605.6, 605.17.2

AWS American Welding Society 550 NW LeJeune Road P. O. Box 351040 Miami, FL 33126


Referenced in code

section number

A5.8—0411 Specifications for Filler Metals for Brazing 605.12.1, 605.14.1, 605.15.1, 705.4.1,

705.7.1, 705.8.1

AWWA American Water Works Association 6666 West Quincy Avenue Denver, CO 80235


Referenced in code

section number

C110—9812 Standard for Ductile Iron and Gray Iron Fittings, 3 Inches through 48 Inches, for Water and Other Liquids


C151—0209 Standard for Ductile Iron Pipe, Centrifugally Cast for Water or Other Liquids

Table 605.4

C510—0007 Double Check-Valve Backflow Prevention Assembly Table 608.1, 608.13.7

C511—0007 Reduced Pressure Principle Backflow Prevention Assembly Table 608.1, 608.13.2, 608.16.2

C651—9905 Standard for Disinfecting Water Mains 610.1

C652—9211 Standard for Disinfection of Water-Storage Facilities 610.1

CISPI Cast Iron Soil Pipe Institute 1064 Delaware Avenue SE Atlanta, GA 30316


Referenced in code

section number

301—0012 Specification for Hubless Cast-Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications


1102.4, Table 1102.5

310—9712 Specification for Coupling for Use in Connection with Cast-Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

705.5.3



Referenced in code

section number

EPCOT Accessibility Code for Building Construction–2015 Edition 404.1, 417.4


EPCOT Building Code–2015 Edition 103.4, 103.6, 108.2, 201.3, 305.4, 307.1,

307.2, 307.3, 309.1.1, 309.1.2, 310.1, 310.3,

403.1, Table 403.1, 404.1, 407.3, 417.6,

606.5.2, 1107.5, 1203.1

EPCOT Electrical Code–2015 Edition 502.1, 1101.7

EPCOT Energy Efficiency Code for Building Construction–2015 Edition 313.1, 607.2

EPCOT Gas Code–2015 Edition 502.1, 1202.1, 1203.1

EPCOT Mechanical Code–2015 Edition 201.3, 310.1, 502.1, 613.1, 1204.1, 1302.1

CSA Canadian Standards Association 178 Rexdale Boulevard Rexdale (Toronto), Ontario Canada M9W 1R3


Referenced in code

section number

A257.1—9214 Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings Table 702.3, Table 1102.4

A257.3—9214 Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

705.6, 705.14

B45.1—02(R2013) Ceramic Plumbing Fixtures 408.1, 416.1, 418.1, 419.1, 420.1

B45.2—02(R2013) Enameled Cast-Iron Plumbing Fixtures 407.1, 415.1, 416.1, 418.1

B45.3—02(R2013) Porcelain-Enameled Steel Plumbing Fixtures 407.1, 416.1, 418.1

B45.4—02(R2013) Stainless Steel Plumbing Fixtures 415.1, 416.1, 418.1, 420.1

B45.5—02(R2013) Plastic Plumbing Fixtures 407.1, 416.2, 417.1, 419.1, 420.1, 421.1

B64.7—9411 Vacuum Breakers, Laboratory-Faucet Type (LFVB) Table 608.1, 608.13.6

B64.10—0111 Manual for the Selection, Installation, Maintenance and Field Testing of Backflow Prevention Devices

312.9

B79—94 (2000)08(R2013) Floor, Area and Shower Drains, and Cleanouts for Residential Construction

412.1

B137.1—0213 Polyethylene Pipe, Tubing and Fittings for Cold Water Pressure Services

Table 605.4

B137.6—0213 CPVC Pipe, Tubing and Fittings for Hot and Cold Water Distribution Systems —with Revisions through May


B181.1—0213 ABS Drain, Waste and Vent Pipe and Pipe Fittings Table 702.1, Table 702.2, Table 702.4,

705.2.2, 715.3

B182.2—0213 PVC Sewer Pipe and Fittings (PSM Type) Table 702.3, Table 1102.4, Table 1102.5

CAN3-B137.8—9913 Polybutylene (PB) Piping for Pressure Applications—with Revisions through July 1992

Table 605.4, Table 605.5, 605.18.2,

605.18.3

CAN/CSA-A257.2—9214 Reinforced L Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings


CAN/CSA-B64.1.1—0111 Vacuum Breakers, Atmospheric Type (AVB) 425.2, Table 608.1, 608.13.6

CAN/CSA-B64.2—0111 Vacuum Breakers, Hose-Connection Type (HCVB) Table 608.1, 608.13.6

CAN/CSA-B64.2.2—0111 Vacuum Breakers, Hose-Connection Type (HCVB) with Automatic Draining Feature

Table 608.1, 608.13.6

CAN/CSA-B64.3—0111 Backflow Preventers, Dual Check-Valve Type with Atmospheric Port (DCAP)

Table 608.1, 608.13.3, 608.15.2

CAN/CSA-B64.4—0111 Backflow Preventers, Reduced Pressure Principle Type (RP) Table 608.1,


608.13.2, 608.15.2

CAN/CSA-B125.3—9405 Plumbing Fittings 408.8, 424.1, 424.2, 424.3, 424.4, 424.5,

424.6, 425.3.1, 425.4, Table 608.1

CAN/CSA-B137.2—9313 PVC Injection-Moulded Gasketed Fittings for Pressure Applications Table 605.6, Table 1102.7

CAN/CSA-B137.3—9313 Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications Table 605.4, 605.20.2, 705.12.2

CAN/CSA-B137.5—8913 Cross-Linked Polyethylene (PBX) Tubing Systems for Pressure Applications—with Revisions through September 1992


CAN/CSA-B137.9—0213 Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems

Table 605.4

CAN/CSA-B137.10—0213 Cross-Linked Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems


CAN/CSA-B181.2—9611 PVC Drain, Waste and Vent Pipe and Pipe Fittings—with Revisions through December 1993

Table 702.1, Table 702.2, 705.12.2,

715.3

CAN/CSA-B181.3—0211 Polyolefin Laboratory Drainage Systems—with Revisions through October 1990


CAN/CSA-B182.1—9211 Plastic Drain and Sewer Pipe and Pipe Fittings 705.12.2

CAN/CSA-B182.4—0211 Profile PVC Sewer Pipe and Fittings Table 702.3, Table 1102.4, Table 1102.5

CAN/CSA-B602—0210 Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe 705.2.1, 705.5.3, 705.6, 705.12.1, 705.13, 705.14

CSA-B45(Supplement 1)—8813 Hydromassage Bathtubs 421.1

FS Federal Specification* U.S. General Services Administration One Constitution Square 1275 First Street, NE Washington, DC 20417


Referenced in code

section number

TT-P-1536a—75 Federal Specification for Plumbing Fixture Setting Compound * Standards are available from the Supt. of Documents, U.S. Government Printing Office, Washington, DC 20402-9325.

405.4



Referenced in code

section number

50—01 Bulk Oxygen Systems at Consumer Sites 1303.1

51—0207 Oxygen-Fuel Gas Systems for Welding, Cutting and Allied Processes 1303.1

70—0511 National Electrical Code 502.1, 1111.3.3

99C—0205 Gas and Vacuum Systems 1302.1

NIST National Institute of Standards and Technology [Formerly National Bureau of Standards (NBS)] 100 Bureau Drive Stop 1070 Gaithersburg, MD 20899


Referenced in code

section number

31 NSB Monograph 31 Table 916.5.1


NSF NSF International 789 N. Dixboro Road P.O. Box 130140 Ann Arbor, MI 48113


Referenced in code

section number

14—0314 Plastic Piping Components and Related Materials 303.3

42—02e14 Drinking Water Treatment Units—Aesthetic Effects 611.1

53—02e14 Drinking Water Treatment Units—Health Effects 611.1

58—0413 Reverse Osmosis Drinking Water Treatment Systems 611.2

61—03e14 Drinking Water System Components—Health Effects 605.4, 605.5, 605.6

PDI Plumbing & Drainage Institute 800 Turnpike Street Suite 300 North Andover, MA 01845


Referenced in code

section number

G101—0312 Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data

1003.3

SECTION 1401 ORGANIZATIONS

The following is a list by name and address of those agencies, associations, institutes and others that are referred to in this Code by name, initials or symbols. Further, there are those listed, for convenience, whose technical and other services are made available to this Code. AGA American Gas Association

400 North Capitol Street NW Suite 450 Washington, DC 20001 www.aga.org

AHRI Air-Conditioning, Heating and Refrigeration Institute (Formerly ARI) 2111 Wilson Boulevard Suite 500 Arlington, VA 22201 www.ahrinet.org



ASPE American Society of Plumbing Engineers 8614 Catalpa Avenue Suite 1007 Chicago, IL 60656


ASSE American Society of Sanitary Engineering 901 Canterbury Suite A Westlake, OH 44145 www.asse-plumbing.org


AWWA American Water Works Association 6666 West Quincy Avenue Denver, CO 80235 www.awwa.org

CDA Copper Development Association 260 Madison Avenue 16th Floor New York, NY 10016 www.copper.org

CISPI Cast Iron Soil Pipe Institute 1064 Delaware Avenue SE Atlanta, GA 30316 www.cispi.org

CSA Canadian Standards Association 178 Rexdale Boulevard Rexdale (Toronto), Ontario Canada M9W 1R3 www.csa-international.org

FM Factory Mutual FM Approvals Standards-Laboratories Department 1151 Boston-Providence Turnpike P.O. Box 9102 Norwood, MA 02062 www.fmglobal.com

FS Federal Specifications U.S. General Services Administration One Constitution Square 1275 First Street NE Washington, DC 20417 www.gsa.gov


NISI National Institute of Standards and Technology [Formerly National Bureau of Standards (NBS)] 100 Bureau Drive Stop 1970 Gaithersburg, MD 20899 www.nist.gov

NSF NSF International 789 North Dixboro Road PO Box 130140 Ann Arbor, MI 48113 www.nsf.org


PDI Plumbing & Drainage Institute 800 Turnpike Street Suite 300 North Andover, MA 01845 www.pdionline.org

PPI Plastics Pipe Institute 105 Decker Court Suite 825 Irving, TX 75062 www.plasticpipe.org