ADJUSTABLECOMFORT

ASSEMBLY INSTRUCTIONS

ADJUSTABLECOMFORT

ASSEMBLY INSTRUCTIONS

STEP 1: Carefully open the carton and remove all boxes then lay out the top and the bottom of the base as one unit as shown. Cut all zip ties and remove.

STEP 2: Attach the center tube with the two center legs and tighten the four center leg bolts with the allen wrench.

STEP 3: Attach each motor by sliding the pins through motor slot at-tached to the frame. The head motor will have a longer shaft than the foot motor.

STEP 4: The label on the motor should be facing up when you are at-taching the motor.

For customer service call 1-877-707-7533 or email azcustomerservice@classicbrands.org

ADJUSTABLECOMFORT

STEP 5: Before plugging each cable into the control box, remove the plug lock that is located between the ports for the cables and the color stickers on the control box. Use your forefinger and thumb to press on the sides of each plug lock to pull off. Plug the cables in the appropri-ate color ports and replace the plug lock. This lock will hold the cables in tightly.

STEP 8: Insert the mattress retainer bar into the grommets as shown.

STEP 6: For the remaining legs, choose the leg height that works for you. To attach the corner bed legs, rotate the end bolts into the holes in the corner brackets. Rotate the center legs into the hole in the pre-at-tached leg.

STEP 7: Put remaining legs on the base and tighten. When ready to flip the base over, make sure you do not use the legs as leverage as they may damage the legs and/or base.

ASSEMBLY INSTRUCTIONSFor customer service call 1-877-707-7533

or email azcustomerservice@classicbrands.org

ADJUSTABLECOMFORT

TV: Press to move the bed to TV position.

HEAD: Press and hold to raise or lower the head section.

M1, M2, M3: Press and hold for 5 seconds to program your favorite position.Press M1, M2, and M3 buttonsto recall positions.

MASSAGE TIMER: Press once to turn on for 10 minutes. Press twice to turn on for 20 minutes.

MASSAGE MODE: Press once to turn on consistent mode.Press twice to turn on slow pulse mode.Press three times to turn on fast pulse mode.Press four times to turn on slow wave mode.Press five times to turn on fast wave mode.

HEAD AND FOOT DOWN: Press and hold to lower the headand foot section at the same time.

FOOT: Press and hold to raise orlower the foot section.

HEAD AND FOOT UP: Press and hold to raise the headand foot section at the same time.

ZERO GRAVITY: Press to move the bed tozero-gravity position.

ANTI-SNORE: Press to move the bed toanti-snore position.

FLAT: Press to move head and footsection to flat position.

LIGHT: Press to turn on flashlight,press again to turn off flashlight.

FOOT MASSAGE: Press once to turn on low intensity.Press twice to turn on medium intensity.Press three times to turn on high intensity.Press four times to turn off.

HEAD MASSAGE: Press once to turn on low intensity.Press twice to turn on medium intensity.Press three times to turn on high intensity.Press four times to turn off.

SYNCING TWO TXL BASES FROM ONE REMOTE: Each base comes synced to its own remote. You can use only one remote so put the 2nd remote away for safekeeping. Bed “A” is already synced. Step 1: Unplug bed “A” and take the “A” remote and sync it to bed “B” Step 2: On the “A” remote press and hold the “head down” button and the “foot up” button at the same time for 10 seconds Step 3: Push the button on the side of the control box underneath bed “B” where it indicates reset coding. Do not press and hold the side button, just press and release. Step 4: Once you hear a beep on bed “B”, plug in bed “A” and they will function as one base.

SYNCING ONE REMOTE:Each base comes factory synced to its own remote. If not synced follow these instructions:Step 1: On the remote press and hold the “head down” button and the “foot up” button and at the same time push the button on the side of the control box underneath the bed where it indicates reset coding. Do not press and hold the side button, just press and release. Step 2: Once you hear a beep that will indicate that the re-mote is synced

HINT: To sync, press all three buttons at the same time.