adhesion method
TRANSCRIPT
-
7/24/2019 Adhesion Method
1/18
NSUR2-1 WhisperteksurfaceDual installaton guide
Span ideaon system
-
7/24/2019 Adhesion Method
2/18
WHAT YOULL NEED
Laser level 3" roller
Two (2) people toinstall the surface.
TABLE OF CONTENTS
Before you begin
Step 1 Measure and mark
Step 2
Aligning surface 1
Step 3 Adhering surface 1
3
4
6
9
Measuring tape
Step 4 Mounting surface 2 14
-
7/24/2019 Adhesion Method
3/18
WhisperTek
TM
Surface installationhttp://nureva-span.uservoice.com/knowledgebase/articles/603927
70F 21C
To avoid cracking, ensure your surfaces have reached
room temperature before removing from the boxes. Allow the
surfaceto rest and flatten for 2 to 3 hours before installation.
BEFORE YOU BEGIN
-
7/24/2019 Adhesion Method
4/18
STEP 1
MEASURE AND MARK
-
7/24/2019 Adhesion Method
5/18
Measure and markSet up the laser lever and project a line 1" above the projected image.
Find the overall centerline of the system. Each surface is 124" (314 cm) long and should extend 1" past the projectedimage. Once you have found the centerline, use a straight edge to mark the entire length of the centerline.
-
7/24/2019 Adhesion Method
6/18
STEP 2
ALIGNING SURFACE 1
-
7/24/2019 Adhesion Method
7/18
Peel the adhesive linerCarefully flip one of the surfaces so the adhesive liner is facing up. Fold down a 6-inch widfrom the edge of the surface to where the liner is cut in the center. Fold down a corner of
on the other side of the cut line.
-
7/24/2019 Adhesion Method
8/18
Align surface 1
Do not let the exposed adhesive touch the wall during this step.
-
7/24/2019 Adhesion Method
9/18
STEP 3
ADHERING SURFACE 1
-
7/24/2019 Adhesion Method
10/18
Adhere the top of the surface
Person B presses the exposed adhesive
against the wall ensuring it is level
with the laser line then firmly smoothes
the top of the surface against the wall.
Hold the surface in place
Once the surface is aligned, person A holds thesurface firmly against the wall.
-
7/24/2019 Adhesion Method
11/18
Remove the adhesive liner
While person A holds their side of the surface, person B pulls the bottom of the surface away fromthe wall to remove the release liner . Do not bend the surface at a sharp angle as this can causekinking.
-
7/24/2019 Adhesion Method
12/18
Begin adhering the surface to the wall
Starting from the top of the surface and moving downward, person B begins to press the surface against the
wall with overlapping up-and-down strokes to prevent bubbles from forming under the surface.
-
7/24/2019 Adhesion Method
13/18
Adhere the second half of surface 1
Once the first half is adhered, person A pulls the surface away from the wall from the side carefully while avoiding
kinking the surface in the center. Person B goes behind the surface to remove the adhesive liner from the second half of
the surface.
Person A holds the outside edge of the surface while person B smoothes it against the wall using up-and-down stokes.
-
7/24/2019 Adhesion Method
14/18
STEP 4
MOUNTING SURFACE 2
-
7/24/2019 Adhesion Method
15/18
Peel the adhesive liner
Carefully flip the other surface so the adhesive liner is facing up. Fold down a 6-inch wide vethe surface that will touch the system centerline. Fold down the corner of the liner on the o
-
7/24/2019 Adhesion Method
16/18
Align and secure surface 2
Person A and person B hold the surface up to the wall. Person A aligns the inside edge of the surface with thesurface that has already been installed. Once the center edge is completely aligned, person A smoothes downthe exposed adhesive to secure the edge of surface 2 against surface 1.
-
7/24/2019 Adhesion Method
17/18
Person B walks the edge of the surface away from the wall so person A can get behind the surface to remove the linerfrom where it was folded.
While person B holds the outside edge, person A goes back to the front of the surface and smoothes that half of thesurface against the wall starting at the centerline using overlapping up-and-down strokes.
Once person A adheres that side of the surface, person A then goes behind the surface again to remove the second
half of the liner to smooth that side of the surface against the wall.
-
7/24/2019 Adhesion Method
18/18
Roller both surfaces
Apply pressure to both the surfaces using the 3" roller to promote proper adhesion. The surface is now readyfor use.
2016 Nureva Inc. All rights reserved. Nureva, Span, WhisperTek and the Span logo are trademarks of Nureva Inc. in the United States, Canada and other countries.