addendum - associated builders & contractors · 2019. 3. 20. · astm e84 – standard test...

ADDENDUM BONNER SPRINGS GOVERNMENT SERVICES CENTER – POLICE FACILITY BONNER SPRINGS ADDENDUM NO. 03 ISSUED: 03/19/2019

1 sfs architecture inc | 2100 central suite #31 kansas city missouri 64108 | o.816.474.1397 f.816.421.8024 www.sfsarch.com

TO DOCUMENTS TITLED: BONNER SPRINGS GOVERNMENT SERVICES CENTER – POLICE FACILITY BID DOCUMENTS FEBRUARY 22, 2019

ARCHITECT-OF-RECORD: SFS Architecture Inc.

2100 Central Suite 31 Kansas City Missouri 64108

The Contract Documents for the above referenced project and the Work covered thereby are modified as described herein.

General Notes and Clarifications:

1. The 1918 Building will be open on Thursday, March 21, 2019 between 8:00 a.m. and 12:00 p.m. All

visitors shall sign in at the front desk at City Hall.

2. Attached is the sign-in sheet from the building walk-through on Thursday, March 14, 2019.

3. The revised bid form is attached to City Hall Addendum No. 3.

4. The City of Bonner Springs will hold the builder’s risk insurance. The AIA A201, General Conditions

of the Contract for Construction will list the insurance requirements and will be issued with the next

addendum.

Specifications:

1. SECTION 00 4100 – BID FORM

a. REMOVE section in its entirety. One bid form shall be submitted that includes a single offer

for the Police Facility and City Hall. A new bid form is attached to City Hall Addendum No. 3.

2. SECTION 00 5200 – AGREEMENT FORM

a. Remove section in its entirety. One agreement will be made for the Police Facility and City

Hall. See the agreement form included in the City Hall specifications.

3. SECTION 01 3000 – ADMINISTRATIVE REQUIREMENTS

a. ADD the following paragraph after paragraph 3.01.C.2.:

i. “3. OpCenter: www.opcenter.com/solutions.”



4. SECTION 04 4200 – STONE MASONRY VENEER

a. ADD the following paragraph after paragraph 2.01.A.5.c.:

i. “1) Acceptable Substitution: Kansas Cottonwood, Bottom Ledge.

a. Grain Direction: Horizontal.

b. Surface Texture: Honed.”

5. SECTION 07 5423 – THERMOPLASTIC POLYOLEFIN (TPO) MEMBRANE ROOFING

a. ADD the following paragraphs after paragraph 2.03.A.1.c.:

i. “d. Firestone UltraPly TPO XR 135 Membrane.

b. ADD the following paragraphs after paragraph 2.05.A.2.c.:

i. “d. Firestone ISO 95+ GL Insulation.

c. REVISE the following paragraphs after paragraph 2.06.A.:

i. “B. Accessories Basis of Design: Carlisle

1. Acceptable Substitutions: GAF, Versico, Johns Manville, Firestone”

6. SECTION 08 7100 – DOOR HARDWARE

a. REVISE Hardware Groups No. 09 and 16-CR as follows:

Hardware Group No. 09

For use on mark/door #(s): 209 212 213 217 218 221

Provide each SGL door(s) with the following:

Qty Description Catalog Number Finish Mfr 4 EA HINGE 5BB1HW 4.5 X 4.5 652 IVE 1 EA OFFICE/ENTRY LOCK L9050L M81A 626 SCH 1 EA ENTRANCE LOCK 8848 X SCHLAGE TRIM M81A 626 ACC 1 EA CYLINDER VERIFY TYPE REQ'D 626 1 EA WALL STOP WS406/407CCV 626 IVE 3 EA SILENCER SR64/65/66 @ NON-RATED GRY IVE

OPERATIONAL DESCRIPTION: LATCHBOLT RETRACTED BY KNOB/LEVER FROM EITHER SIDE UNLESS OUTSIDE IS MADE INOPERATIVE BY KEY OUTSIDE OR BY TURNING INSIDE THUMBTURN. WHEN OUTSIDE IS LOCKED, LATCHBOLT IS RETRACTED BY KEY OUTSIDE OR BY KNOB/LEVER INSIDE. INSIDE LEVER IS ALWAYS FREE FOR EGRESS.



Hardware Group No. 16-CR

For use on mark/door #(s): 116A-CR 201A-CR 205-CR 206-CR 207A-CR 207C-CR 219-CR 225-CR

Provide each SGL door(s) with the following:

Qty Description Catalog Number Finish Mfr 4 EA HINGE 5BB1HW 4.5 X 4.5 652 IVE 1 EA POWER TRANSFER EPT10 689 VON 1 EA EU MORTISE LOCK L9092LEU M81A RX LX CON 626 SCH 1 EA STOREROOM LOCK 8859 X SCHLAGE TRIM M81A 626 ACC 1 EA ELECTRIC STRIKE 6211AL FSE 628 VON 1 EA CYLINDER VERIFY TYPE REQ'D 626 1 EA SURFACE CLOSER 4050 RW/PA 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 626 IVE 1 EA WALL STOP WS406/407CCV 626 IVE 3 EA SILENCER SR64/65/66 @ NON-RATED GRY IVE 1 EA MULTITECH READER MT15 - WORK OF DIV. 28 BLK SCE 1 EA DOOR CONTACT 679-05 WHT SCE 1 EA POWER SUPPLY PS902 900-2RS LGR SCE

OPERATIONAL DESCRIPTION: DOOR CLOSED AND OUTSIDE LEVER LOCKED, ACCESS VIA CARD READER OR KEY OVERRIDE. FREE EGRESS AT ALL TIMES.

7. SECTION 09 6700 – FLUID-APPLIED FLOORING

a. ADD the following paragraph after paragraph 2.01.A.1.:

i. “2. Dur-A-Flex; www.dur-a-flex.com.”

8. SECTION 10 1400 – SIGNAGE

a. REVISE paragraph 2.04.A.1. to read as follows:

i. “Metal: Aluminum sheet, flat.”

b. ADD the following paragraphs after Section 2.04.A.2.:

i. “2. Finish (Letters): Brushed, satin.

ii. 3. Finish (Sunflower): Kynar finish, custom color.

iii. 4. Thickness: 3/8””

9. SECTION 10 2113.19 – PLASTIC TOILET COMPARTMENTS

a. ADD the following paragraphs after Section 1.01:

i. “1.02 REFERENCE STANDARDS”

1. “A. ASTM E84 – Standard Test Method for Surface Burning Characteristics

of Building Materials; 2016.”



2. “B. NFPA 286 – Standard Methods of Fire Tests for Evaluating Contribution

of Wall and Ceiling Interior Finish to Room Fire Growth; 2015.”

10. SECTION 10 5113 – METAL LOCKERS

a. ADD the following paragraph after Section 2.01.A.1.:

i. “2. ALB Plus Tactical Lockers; www.albplus.ca.”

11. SECTION 10 7316.13 – METAL CANOPIES

a. REPLACE section in its entirety with the attached revised section.

Drawings:

1. A150 – FINISH LEGEND AND SCHEDULE

a. ADD the following to finish type EP-1 – EPOXY-RESIN TYPE - 1:

i. “OR Dur-A-Flex; Dur-A-Quartz; Color as selected by Architect from Manufacturer’s

full range of standard colors.”

2. A561 – SIGNAGE

a. ADD detail B1/A561.

b. REVISE detail D5/A561 note to read “routed text” in lieu of “1/2” bevel relief characters”

3. M700 – MECHANICAL CONTROLS

a. REMOVE Z-FLT point from temperature sensor on details #2/M700 & #4/M700.

4. E202 – POWER BASEMENT & COURT FLOOR PLAN

b. ADD switch locations for the motorized shades and switch glass.

5. E203 – POWER GROUND FLOOR PLAN

a. ADD power connections to motorized shades and switch glass.

6. E612 – LIGHT FIXTURE SCHEDULE

a. ADD light fixture equal to the following fixture types:

i. A5/ A5E

ii. C1

iii. C2

iv. C3



7. E613 – LIGHT FIXTURE SCHEDULE

a. ADD light fixture equal to the following fixture types:

i. F5/F5E

ii. SW1/ SW1E

iii. SW2/ SW2E

iv. W5

v. X1

8. E622 – PANELBOARD SCHEDULE

a. ADD connections to existing spare breakers.

Attachments: Pre-Bid Walk-Through Attendees, dated 03/14/2019

SECTION 10 7316.13 – METAL CANOPIES

SHEETS A561, E611, E612

END OF ADDENDUM

SFS / 17973 Bonner Springs Government Services CenterPolice Facility

METAL CANOPIES Bid Documents02/22/2019

10 7316.13 - 1

SECTION 10 7316.13

METAL CANOPIES

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Extruded aluminum overhead hanger rod style metal canopies.

1.02 REFERENCE STANDARDS

A. ASTM A36/A36M - Standard Specification for Carbon Structural Steel; 2014.

B. ASTM A307 - Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000PSI Tensile Strength; 2014 (Editorial 2017).

C. ASTM A500/A500M - Standard Specification for Cold-Formed Welded and Seamless CarbonSteel Structural Tubing in Rounds and Shapes; 2013.

D. ASTM A572/A572M - Standard Specification for High-Strength Low-AlloyColumbium-Vanadium Structural Steel; 2015.

E. ASTM C1107/C1107M - Standard Specification for Packaged Dry, Hydraulic-Cement Grout(Nonshrink); 2014a.

F. ASTM F593 - Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs;2017.

G. ASTM F3125/F3125M - Standard Specification for High Strength Structural Bolts, Steel andAlloy Steel, Heat Treated, 120 ksi (830 MPa) and 150 ksi (1040 MPa) Minimum TensileStrength, Inch and Metric Dimensions; 2015a.

H. AWS D1.1/D1.1M - Structural Welding Code - Steel; 2015, with Errata (2016).

1.03 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.

B. Product Data: Submit product data sheets, including material descriptions and finishes, andpreparation instructions and recommendations.

C. Shop Drawings: Prior to commencement of fabrication, submit detailed shop drawings,showing profiles, sections of components, finishes, and fastening details.

D. Design Data: Submit comprehensive structural analysis of design for the specified loads.Stamp and sign calculations by professional engineer.

E. Manufacturer's Qualification Statement.

F. Warranty Documentation: Submit manufacturer warranty and ensure that forms have beencompleted in Owner's name and registered with manufacturer.

1.04 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in the manufacture of products similar tothose required for this project.

1. Not less than three years of documented experience.

1.05 DELIVERY, STORAGE, AND HANDLING

A. Deliver materials to project site ready for erection.

B. Package using methods that prevent damage during shipping and storage on site.

C. Store materials under cover and elevated above grade.

1.06 WARRANTY

A. See Section 01 7800 - Closeout Submittals, for additional warranty requirements.

B. Metal Canopies: Correct defective work within a two year period after Date of SubstantialCompletion.

Bonner Springs Government Services CenterPolice Facility

SFS / 17973

10 7316.13 - 2 Bid Documents02/22/2019

METAL CANOPIES

C. Finish Warranty: Provide manufacturer's one year warranty on factory finish against cracking,peeling, and blistering.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Metal Canopies:

1. Mapes Canopies: www.mapescanopies.com.

2. Peachtree Protective Covers, Inc.; www.peachtreecovers.com.

3. Substitutions: See Section 01 6000 - Product Requirements.

2.02 METAL CANOPIES

A. Shop Fabricated Metal Canopy Type: Hanger Rod Supported Flat Soffit Super Lumideck, 8" JFascia.

2.03 COMPONENTS

A. Structural Steel Framing:

1. Columns: ASTM A500/A500M, Grade B, round or rectangular tubing, sized to suit projectdesign load requirements.

2. Base and Top Plates: ASTM A36/A36M, with pre-drilled bolt holes.

3. Beams: Wide flange, ASTM A572/A572M, Grade 50.

4. Other Structural Steel Members: ASTM A36/A36M.

B. Covering:

1. Sheet Metal Decking: Interlocking metal panels.

a. Panel Size: 16 inches wide by 3 inches deep; 20 gauge, 0.0359 inch thickness.

b. Provide canopy manufacturer's standard clip type fasteners for attaching covering tostructural beams.

C. Fascia: Manufacturer's standard flat profile.

D. Anchor Bolts: ASTM A307 or ASTM A572/A572M, formed with bent shank, assembled withtemplate for casting into concrete.

1. Minimum exposed thread of 7 inches above footing and 23 inch minimum embedment.

2. Provide nuts and washers as required for column leveling and plumbing.

E. Exposed Gutters and Downspouts: Galvanized steel with baked enamel finish, color to matchcanopy covering, manufacturer's recommended size for canopy specified.

2.04 SHOP FABRICATION

A. Extruded aluminum canopy shipped with the materials precut to size for field assembly.

B. All connections shall be mechanically assembled utilizing 3/16 fasteners with a minimum shearstress of 350 lb. Pre-welded or factory-welded connections are not acceptable.

C. Perform welding in accordance with AWS D1.1/D1.1M.

D. Concealed drainage. Water shall drain from covered surfaces into intermediate trough and bedirected to Front Scupper.

2.05 FINISHES

A. Class II Clear Anodized:

1. Shop Primer: Rust-inhibitive red oxide.

B. Steel Decking: Polyester baked enamel finish; color as selected from manufacturer's standardrange.

C. Fascia: Polyester baked enamel finish; color as selected from manufacturer's standard range.

2.06 ACCESSORIES

A. Structural Bolts: ASTM F3125/F3125M, Grade A325, minimum 3/4 inch diameter.

B. Trim, Closure Pieces, and Flashings: Same material, thickness and finish as sheet metaldecking; factory-fabricated to required profiles.

SFS / 17973 Bonner Springs Government Services CenterPolice Facility

METAL CANOPIES Bid Documents02/22/2019

10 7316.13 - 3

1. Exposed Fasteners: Not permitted.

C. Grout: ASTM C1107/C1107M; non-shrinking; premixed compound consisting of non-metallicaggregate, cement, water-reducing and plasticizing agents.

D. Fasteners, Non-Structural: ASTM F593 stainless steel or ASTM A307 carbon steel.

PART 3 EXECUTION

3.01 EXAMINATION

A. Examine substrates and site area for conditions that might prevent satisfactory installation.

B. Verify that foundation, electrical utilities, and placed anchors are in correct position.

C. Do not proceed with installation until all conditions are satisfactory.

3.02 INSTALLATION - FRAMING

A. Provide for erection and wind loads. Provide temporary bracing to maintain structure plumband in alignment until completion of erection and installation.

B. Set column base plates with non-shrink grout to achieve full plate bearing.

C. Fasten columns to anchor bolts.

D. Do not field cut or alter structural members without approval.

E. After erection, prime welds, abrasions, and surfaces not shop primed.

3.03 INSTALLATION - CANOPY COVERING

A. Install in accordance with manufacturer's instructions.

B. Fasten metal decking to steel support members, aligned level and plumb.

C. Install fascia panels, trim, and flashing.

D. Separate dissimilar metals using concealed bituminous paint.

E. Touch-up damaged finish coating using material provided by manufacturer to match originalcoating.

3.04 TOLERANCES

A. Maximum Variation from Level: Plus/Minus 1/8 inch.

3.05 CLEANING

A. Clean surfaces of dust and debris; follow manufacturer's cleaning instructions for the finishused.

3.06 PROTECTION

A. Protect canopy after installation to prevent damage due to other work until Date of SubstantialCompletion.

END OF SECTION 10 7316.13

PICTOGRAM; REFER TO SCHEDULE

SIGNAGE TYPE 3 NOTES:

MESSAGE

1 7

/8"

1 3

/8"

2 5

/8"

1"

1" 2 1/2" 1 1/8"

3/8

"5

/8"

9"

1 1

/8"

9"

1. SIGN BODY SHALL BE 1/16" ALUMINUM-BACKED PHOTOPOLYMER, NATURAL FINISH W/ VERTICAL GRAIN, WITH 3/16" CLEAR ACRYLIC BACKPLATE.

2. SIGN MESSAGE AND PICTOGRAM SHALL BE 3/32" TACTILE LETTERING INTEGRAL TO PHOTOPOLYMER, COLOR: BLACK, FINISH: MATTE, TEXT FONT: CALIBRI.

3. GRADE 2 BRAILLE RAISED .25"-.37" SHALL BE USED.4. THERE SHALL BE A MINIMUM OF 3/8" CLEARANCE AROUND ALL

FOUR SIDES OF BRAILLE.5. SIGNS SHALL BE MANUFACTURED IN COMPLIANCE WITH ALL

LOCAL CODE AND ADA REQUIREMENTS FOR BACKGROUND AND LETTER CONTRAST, CHARACTER HEIGHTS AND WIDTHS, MOUNTING LOCATIONS, ETC.

6. REFER TO SIGNAGE SCHEDULE FOR PICTOGRAM TYPE. PICTOGRAM SHALL ALIGN WITH LEFT SIDE OF TEXT.

TYP

9"

TY

P

9"

TYPE AMEN

TYPE BWOMEN

TYPE CFAMILY

TYPE DAED

TYPE ESTAIRS

TYPE FELEVATOR

TYPE GSTAIR DIRECTION

MAXIMUM OCCUPANCY

XXX

EQ

EQ

4 1

/2"

3"

1"

1/2

"

SIGNAGE TYPE 2 NOTES:EQ EQ

9"






6. REFER TO SIGNAGE SCHEDULE FOR OCCUPANCY COUNT.

MESSAGEMESSAGE

1/2

"1

3/8

"

4 1

/2"

5/8

"

9"

EQ EQ

SIGNAGE TYPE 1 NOTES:






6. REFER TO SIGNAGE SCHEDULE FOR ROOM NAME.

3' -

3"

3' - 3" 6" 14' - 2 1/2"

6"

6"

5' - 8 7/8"

1' -

0"

DIMENSIONAL LETTER SIGNAGE(10 1400)

DIMENSIONAL LETTER SIGNAGE(10 1400)

2' - 2"

1' -

0"

1" DEEP BEVEL RELIEF CHARACTERS ALL TEXT AND FONTS TO BE COMPLIANT WITH CITY OF BONNER SPRINGS STANDARDS ARCHITECT TO PROVIDE VECTOR GRAPHICS FOR RELIEF LETTERING

RETAINING WALL, BUFF-COLORPIGMENTED,SMOOTH RUBBED FINISH (RE:CIVIL)

9"

2"

3' - 9 3/8"

1/2" DEEP BEVEL RELIEF CHARACTERS ALL TEXT AND FONTS TO BE COMPLIANT WITH CITY OF BONNER SPRINGS STANDARDS ARCHITECT TO PROVIDE VECTOR GRAPHICS FOR RELIEF LETTERING

STONE MASONRY VENEER,LIMESTONE (04 4200)

EQ EQ

5' - 0"

3' -

4"

6"

4 3

/4"

TY

P.

1 1

/2"

TY

P.

1 1

/2"

3"

6"

ROUTED ACRYLIC SIGN ONMETAL (10 1400)

MOUNTED ON IMPALING Z-CLIPS

ROUTED TEXT, ALL TEXT AND FONTS TO BE COPMLIANTWITH CITY OF BONNER SPRINGS STANDARDS.ARCHITECT TO PROVIDE VECTOR GRAPHICSFOR RELIEF LETTERING.

1/2" DEEP BEVEL RELIEF POLICEDEPARTMENT SEAL TO BECOMPLIANT WITH CITY OFBONNER SPRINGS STANDARDSARCHITECT TO PROVIDEVECTOR GRAPHICS FOR RELIEFSEAL (10 1400)

1/2" DEEP BEVEL RELIEFCHARACTERS ALL TEXT ANDFONTS TO BE COMPLIANT WITHCITY OF BONNER SPRINGSSTANDARDS ARCHITECT TOPROVIDE VECTOR GRAPHICSFOR RELIEF LETTERING (101400)

STONE MASONRY VENEER,LIMESTONE (04 4200)

2' - 9 3/8"

3' -

6"

6' - 4" 2' - 0 1/4"

1' -

6 1

/4"

© 2018 SFS ARCHITECTURE

2 1

0 0

C

e n

t r

a l

S t . S

u i

t e 3

1 K

a n

s a

s C

i t y

, M

O 6

4 1

0 8

(O)

8 1 6. 4

7 4. 1

3 9 7 (

F)

8 1 6. 4

2 1. 8

0 2 4 w

w

w

. s

f s

a r

c h. c

o m

sfsarchitecture

© 2

018

54321

D

C

B

A

MARK DATE DESCRIPTION

C:\U

sers

\dfo

lso

m\D

ocu

me

nts

\179

73_

Bon

ne

rSp

rin

gsG

overn

me

ntS

erv

ice

sC

en

ter_

Po

lice_

R1

8_d

fols

om

@sfs

arc

h.c

om

.rvt

3/1

4/2

01

9 3

:10:2

4 P

M

A561

SIGNAGE

CIT

Y O

F B

ON

NE

R S

PR

ING

S, K

AN

SA

S

BO

NN

ER

SP

RIN

GS

GO

VE

RN

ME

NT

SE

RV

ICE

S C

EN

TE

RP

OL

ICE

FA

CIL

ITY

SFS PROJECT NO: 17973

ISSUE DATE: 02/22/2019

ISSUED FOR: BID DOCUMENTS

21

5 C

ED

AR

ST

.B

ON

NE

R S

PR

ING

S, K

S 6

60

12

3" = 1'-0"A561

B5 SIGNAGE - Type 3

1 1/2" = 1'-0"A561

A5 SIGNAGE - Pictograms

3" = 1'-0"A561

C5 SIGNAGE - Occupancy

3" = 1'-0"A561

C5.1 SIGNAGE - Room ID

1/2" = 1'-0"A561

A1 SIGNAGE - EXTERIOR FACILITY SIGNAGE

1/2" = 1'-0"A561

A2 SIGNAGE DETAIL - 215 ADDRESS1/2" = 1'-0"A561

A3 SIGNAGE DETAIL - HONOR RESPECT REMEMBER

1" = 1'-0"A561

D5 SIGNAGE DETAIL - ON MY HONOR

SIGNAGE

Number Type Pictogram Description Sign Message Sign Message 2Sign Mounting

LocationRoom:

Number Room: Name Comments

101 TYPE 3 TYPE A ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS RESTROOM BRAILLE WALL 101 MENS SHOWER

102 TYPE 3 TYPE A ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS RESTROOM BRAILLE WALL 102 MENS SHOWER

103 TYPE 3 TYPE B ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS RESTROOM BRAILLE WALL 103 WOMENS SHOWER

104 TYPE 3 TYPE A ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS MEN'S LOCKER BRAILLE WALL 104 LOCKER MEN'S.

105 TYPE 3 TYPE B ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS WOMEN'S LOCKER BRAILLE WALL 105 LOCKER WOMEN'S

106 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS ARMORY BRAILLE WALL 106 ARMORY

108 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS PLUMBING BRAILLE WALL 108 PLUMBING ROOM

109 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS EVIDENCE HOLDING BRAILLE WALL 109 EVI. HOLD

110 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS EVIDENCE STORAGE BRAILLE WALL 110 EVIDENCE STORAGE

112 TYPE 3 TYPE F ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS ELEVATOR BRAILLE WALL 100 ELEV.

112 TYPE 3 TYPE F ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS STAIR BRAILLE WALL 100 ELEV.

112 TYPE 3 TYPE E ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS STAIR BRAILLE WALL 112 CORRIDOR

114 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS ELECTRICAL BRAILLE WALL 114 ELECTRICAL RM.

115 TYPE 3 TYPE C ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS FAMILY RESTROOM BRAILLE WALL 115 TOILET

117 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS INTERVIEW BRAILLE WALL 117 INTERVIEW

119 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS STORAGE BRAILLE WALL 119 STORAGE

120 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS JANITOR'S CLOSET BRAILLE WALL 120 JAN.

120 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS JUVINILE INT. BRAILLE WALL 118 JUV. INTER.

121 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS BONDING BRAILLE WALL 121 BOND

124 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS K9 STORAGE BRAILLE WALL 124 K9 STOR.


128 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS GYM & LOCKERS BRAILLE WALL 128 EXERCISE ROOM

201 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS TRAINING ROOM BRAILLE GLASS 201 TRAINING

201 TYPE 2 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS MAXIMUM OCCUPANCY - 60 BRAILLE GLASS 201 TRAINING

202 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS STORAGE BRAILLE WALL 202 TRAINING STORAGE

203 TYPE 2 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS MAXIMUM OCCUPANCY - 187 BRAILLE WALL 203 VEST.

205 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS RECORD CLERK BRAILLE WALL 205 RECORD CLERK

206 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS SARGENT TECHNICAL BRAILLE GLASS 206 SGT TECH



207 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS OFFICE BRAILLE GLASS 213 OFFICE


208 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS INTERVIEW MONITOR BRAILLE WALL 208 INT. MONITOR

209 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS SARGENT INVESTIGATIVE BRAILLE GLASS 209 SGT INVESTIGATIVE

210 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS INTERVIEW HARD BRAILLE WALL 210 INT. HARD

211 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS INTERVIEW SOFT BRAILLE WALL 211 INT. SOFT

212 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS CORPORAL DETECTIVE BRAILLE GLASS 212 CORP. DETECTIVE

215 TYPE 3 TYPE B ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS WOMEN'S TOILET BRAILLE WALL 215 WOMEN TLT

216 TYPE 3 TYPE A ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS MEN'S TOILET BRAILLE WALL 216 MEN TLT

217 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS OFFICE BRAILLE GLASS 217 OFFICE

218 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS MAJOR BRAILLE GLASS 218 MAJOR

219 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS SERVER BRAILLE WALL 219 SERVER

220 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS INTERVIEW BRAILLE WALL 220 INT. ROOM

221 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS CHIEF BRAILLE GLASS 221 CHIEF

222 TYPE 3 TYPE A ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS MEN'S RESTROOM BRAILLE WALL 222 MEN'S RR

223 TYPE 3 TYPE B ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS WOMEN'S RESTROOM BRAILLE WALL 223 WOMEN'S RR

224 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS BREAKROOM BRAILLE WALL 224 BREAK/ VEND.

225 TYPE 1 - ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITHOUT SYMBOLS CONFERENCE BRAILLE GLASS 225 CONFERENCE

227 TYPE 3 TYPE D ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS AED BRAILLE WALL 227 CORRIDOR

227 TYPE 3 TYPE G ADA ROOM ID; RAISED LETTERS; GRADE 2 BRAILLE; WITH SYMBOLS STAIR DIRECTION BRAILLE GLASS 227 CORRIDOR

PIN MOUNTED METAL PAN SIGN, SUNFLOWER MUST BE COMPLIANT WITHCITY OF BONNER SPRINGS STANDARDS, ARCHITECT TO PROVIDE VECTORGRAPHIC IMAGE (10 1400)

3 03/19/19 ADDENDUM 3

3

1/2" = 1'-0"A561

B1 SIGNAGE - INTERIOR FACILITY SIGNAGE

3

FAXTEL


2 1

0 0

C

e n

t r

a l

S t . S

u i

t e 3

1 K

a n

s a

s C

i t y

, M

O 6

4 1

0 8

(O)

8 1 6. 4

7 4. 1

3 9 7 (

F)

8 1 6. 4

2 1. 8

0 2 4 w

w

w

. s

f s

a r

c h. c

o m

sfs

archite

ctu

re

© 2

014

54321

D

C

B

A


(816) 663-8700 (816) 663-8701KANSAS CITY, MO 64108

1801 MAIN, SUITE 300

WWW.HENDERSONENGINEERS.COM

C:\R

evit\P

roje

cts\

Bo

nne

r S

prin

gs P

olic

e_

ME

P_

ma

ria

un

ruh

_2

01

90

319

10

54

01.r

vt

3/1

9/2

019

10:5

8:2

1 A

M

E611

LIGHT FIXTURESCHEDULE

CIT

Y O

F B

ON

NE

R S

PR

ING

S, K

AN

SA

S

BO

NN

ER

SP

RIN

GS

GO

VE

RN

ME

NT

SE

RV

ICE

S C

EN

TER

-PO

LIC

E F

AC

ILIT

Y


ISSUE DATE: 02 / 22 /2019


20

0 E

3R

D S

T.

BO

NN

ER

SP

RIN

GS

, K

S 6

60

12

AN

DR

EA

C. M

ULV

AN

Y

1850002088KS. CORPORATE NO: E-325

EXPIRES 12/31/2020

OR PRE-APPROVED EQUAL MANUFACTURER

BY

FLOOD-34 DEGREE 1200 LUMENS

MAS3B2-TI-RD/ (3) LED-530-2850K- 3 95 CRI, 2850K BEAM.

D1A MODULAR INTERNATIONAL LED (3) LED 120 90 95 SAME AS TYPE D1 EXCEPT WITH INDIVIDUAL 34 DEGREE OPTICAL SYSTEMS YIELDING A NOMINAL 2,000 CANDELA 1,2,3

5% OF FULL OUTPUT.

DRIVERS SUITABLE FOR 30 WATT MODULE AND ELV DIMMING WITH PHASE ADAPTIVE MODULE FOR DIMMING TO

TO YIELD NOMINAL 7,000 MAIN BEAM CANDELA. MANUFACTURER TO FURNISH FIXTURE WITH INDIVIDUAL DIMMABLE

OR PRE-APPROVED EQUAL MANUFACTURER ADJUSTABLE DOUBLE GIMBAL LED MODULE FOR 45 DEGREE AIMING AND INTEGRAL 21 DEGREE OPTICAL SYSTEM

BY EACH APERTURE TO CONTAIN MANUFACTURER'S DEDICATED NATIVE BORN

SPOT-21 DEGREE 1200 LUMENS 3-PORT HOUSING. INTERIOR TO BE WHITE.

M3(30)LEDxTI-REC-TR-SC/ (3) LED-530-2850K- 3 95 CRI, 2850K RECESSED MULTI-LAMP WARM WHITE 2850K LED FIXTURE WITH INDIVIDUAL LED MODULES ON 6" CENTERS WITHIN

D1 MODULAR INTERNATIONAL LED (3) LED 120 90 95 3 MULTIPLE TRIMMED FIXTURED. NOMINAL 4" DIAMETER APERTURE WITH 20-1/8" LONG X 7-3/4" WIDE X 8" DEEP 1,2,3

S7075 SERIESOR EQUAL BY SCOTT ARCH LIGHTING 95 CRI DETERMINED BY ARCHITECT. CONTRACTOR TO PROVIDE AN ALLOWANCE BASED ON SPECIFIED FIXTURE.

OR AS OTHERWISE SELECTED BY ARCHITECT 2700K CONTRACTOR TO PROVIDE WITH SPECIFIED LED REPLACEMENT LAMPS FROM SORAA. EXACT FIXTURE TO BE

1609F-OB 927-01 DIFFUSER AND OXIDIZED BRONZE FINISH WITH ONE (1)) MEDIUM BASE SOCKET U.L LISTED FOR 100 WATTS EACH.

EDISON COLLECTION 1 SA19-11-OMNI ONLY LED REPLACEMENT LAMP. FIXTURE EQUIPPED WITH FROSTED GLASS "SCHOOLHOUSE" STYLE FROSTED GLASS

C3 HUDSON VALLEY LIGHTING LED (1) SORAA 120 11 13 NOMINAL 12" DIAMETER X 11.5" DEEP SURFACE MOUNTED DECORATIVE MEDIUM BASE SOCKET FIXTURE WITH 1,2,3



19-OB-1612 927-01 DIFFUSER AND OXIDIZED BRONZE FINISH WITH ONE (1)) MEDIUM BASE SOCKET U.L LISTED FOR 100 WATTS EACH.


C2 HUDSON VALLEY LIGHTING LED (1) SORAA 120 11 13 NOMINAL 11.75" DIAMETER X 14.50" DEEP PENDANT MOUNTED DECORATIVE MEDIUM BASE SOCKET FIXTURE WITH 1,2,3



19-OB-1615 927-01 DIFFUSER AND OXIDIZED BRONZE FINISH WITH ONE (1)) MEDIUM BASE SOCKET U.L LISTED FOR 100 WATTS EACH.


C1 HUDSON VALLEY LIGHTING LED (1) SORAA 120 11 13 NOMINAL 15" DIAMETER X 17.25" DEEP PENDANT MOUNTED DECORATIVE MEDIUM BASE SOCKET FIXTURE WITH 1,2,3

LOCATE EMERGENCY SECTION PER PLAN OR NEAREST TO THE PATH OF EGRESS.

OR EQUAL BY AXIS BEAM 4 60,000 HOURS

OR EQUAL BY FINELITE HP4 SERIES 875 LUMNES/FT

FS4ML-FL-875LF-35K-1C-UNV-LD1-X-EM-WH-(XFT) 80 CRI, 3500K

A9E-X' FOCAL POINT - LED UNV 9.1W/FT 10W/FT SIMILAR TO TYPE A2E WITH 875 LUMEN OUTPUT PER LINEAR FOOT. 1,2,3,5

ADJACENT FIXTURES TO BE CONTINUOUS RUNS. LENGTHS TO BE EVENLY DIVIDED.

WHITE FIXTURE HOUSING FINISH. REFER TO DRAWINGS FOR FIXTURE LENGTH.


OR EQUAL BY FINELITE HP4 SERIES 875 LUMNES/FT

FS4ML-FL-875LF-35K-1C-UNV-LD1-X-WH-(XFT) 80 CRI, 3500K

A9-X' FOCAL POINT - LED UNV 9.1W/FT 10W/FT SIMILAR TO TYPE A2 WITH 875 LUMEN OUTPUT PER LINEAR FOOT. 1,2,3,5

PROVIDE DRYWALL FRAME KIT AS REQUIRED PER FIXTURE.

OR EQUAL BY AXIS DIALED SERIES 50,000 HOURS CONTRACTOR TO COORDINATE WITH FINAL SPECIFIED CEILINGS AND

OR EQUAL BY FOCAL POINT FEQ SERIES 4300 LUMENS WHITE POWDER COAT FINISH. DIFFUSE OPTICAL DISTRIBUTION PATTERN. INTEGRAL 0-10V DRIVER.

HPR LED-A-2X2-DCO-B-835-277V-SC-C 80 CRI, 3500K AND 20 GAUGE STEEL.

A8 FINELITE - LED UNV 37 41 2'X2' RECESSED LED FIXTURE WITH ANGLE LENS AND HOUSING FORMED FROM EXTRUDED ALUMINUM 1,2,3

OR EQUAL BY AXIS DIALED SERIES 50,000 HOURS

OR EQUAL BY FOCAL POINT FEQ SERIES 4800 LUMENS

HPR LED-A-2X4-DCO-B-835-277V-C 80 CRI, 3500K FOR A MINIMUM OF 90 MINUTES.

A7E FINELITE - LED UNV 35 39 SAME AS TYPE A7 WITH INTEGRAL EMERGENCY DRIVER CAPABLE OF DELIVERING 1500 LUMENS 1,2,3

PROVIDE DRYWALL FRAME KIT AS REQUIRED PER FIXTURE.

OR EQUAL BY AXIS DIALED SERIES 50,000 HOURS CONTRACTOR TO COORDINATE WITH FINAL SPECIFIED CEILINGS AND

OR EQUAL BY FOCAL POINT FEQ SERIES 4300 LUMENS WHITE POWDER COAT FINISH. DIFFUSE OPTICAL DISTRIBUTION PATTERN. INTEGRAL 0-10V DRIVER.

HPR LED-A-2X4-DCO-B-835-277V-SC-C 80 CRI, 3500K AND 20 GAUGE STEEL.

A7 FINELITE - LED UNV 35 39 2'X4' RECESSED LED FIXTURE WITH ANGLE LENS AND HOUSING FORMED FROM EXTRUDED ALUMINUM 1,2,3


OR EQUAL BY AXIS BEAM 4 WHITE FIXTURE HOUSING FINISH. REFER TO DRAWINGS FOR FIXTURE LENGTH.

OR EQUAL BY FINELITE HP4 SERIES 60,000 HOURS WITH INTEGRAL CONSTANT CURRENT REDUCTION. 0-10V DIMMING DRIVER. POLYESTER POWDER COAT MATTE

WH-(XFT) 625 LUMNES/FT CONTRACTOR TO COORDINATE CEILING CONFIGURATION WITH FINAL CEILING SPECIFICATION. FIXTURE EQUIPPED

FS4ML-FL-625LF-35K-1C-UNV-LD1-TF- 80 CRI, 3500K ALUMINUM HOUSING AND CONTINUOUS APPEARANCE FROSTED ACRYLIC FLUSH SATIN FINISH LENS.

A6-X' FOCAL POINT - LED UNV 6.5W/FT 7W/FT NOMINAL 4" WIDE X 5" HIGH X VARYING FEET LONG RECESSED LINEAR LED. FIXTURE CONSISTS OF EXTRUDED 1,2,3,5

OR EQUAL BY L.C. DOANE CRF SERIES

OR EQUAL BY LITHONIA VRTL SERIES 50,000 HOURS

OR EQUAL BY COOPER 2VR SERIES 5700 LUMENS

HASEDI-24-55C43K-DCC-DV-2F-2H-SYM/9-LEL 80 CRI, 3700K OF OPERATING 700 LUMENS IN EMERGENCY MODE FOR A MINIMUM OF 90 MINUTES.

A5E KENALL - LED UNV 55 64 SAME AS FIXTURE TYPE A5 EXCEPT WITH EMERGENCY DRIVER. EMERGENCY DRIVER SHALL BE CAPABLE 1,2,3

OR EQUAL BY L.C. DOANE CRF SERIES

OR EQUAL BY LITHONIA VRTL SERIES 50,000 HOURS IP65 / UL WET LOCATION LISTED.

OR EQUAL BY COOPER 2VR SERIES 5700 LUMENS WHITE POWDER COAT FINISH. 18 GAUGE STEEL CONSTRUCTION.

HASEDI-24-55C43K-DCC-DV-2F-2H-SYM/9 80 CRI, 3700K CONTINUOUS HINGE SECURED WITH TAMPER RESISTANT FASTENERSA AND LENS SEALED TO DOORFRAME.

A5 KENALL - LED UNV 55 62 2'X4' RECESSED LENSED LED TROFFER WITH ONE-PIECE SEAM-WELDED HOUSING, INSET DOORFRAME 1,2,3


REFER TO DRAWINGS FOR FIXTURE LENGTH.

OR EQUAL BY AXIS PERIMETER SERIES 60,000 HOURS 0-10V DIMMING DRIVER.POLYESTER POWDER COAT MATTE WHITE FINISH.

OR EQUAL BY FINELITE HP-WS SERIES 300 LUMENS/FT CONTRCTOR TO COORDINATE CEILING CONFIGURATION WITH FINAL CELING SPECIFICATION.

FTRL-AC-LL1-35K-1C-UNV-LD1-XF-WH-XX' 80 CRI, 3500K ALUMINUM LED HOUSING WITH 20 GAUGE STEEL FIXTURE HOUSING. RIBBED EXTRUDED FROSTED ACRYLIC LENS.

A4 FOCAL POINT - LED UNV 5.75/FT 7/FT NOMINAL 4" WIDE X 7.3" HIGH X VARYING FEET LONG RECESSED COVE HOUSING WITH FROSTED LENS. EXTRUDE 1,2,3,5

OF OPERATING 10 WATTS IN EMERGENCY MODE FOR A MINIMUM OF 90 MINUTES.

PROVIDE WITH EMERGENCY DRIVER. EMERGENCY DRIVER SHALL BE CAPABLE


OR EQUAL BY AXIS BEAM 4 60,000 HOURS REFER TO DRAWINGS FOR FIXTURE LENGTH.

OR EQUAL BY FINELITE HP4 SERIES 875 LUMNES/FT POLYESTER POWDER COAT MATTE WHITE FIXTURE HOUSING FINISH.

FS4ML-FL-875LF-35K-1C-UNV-LD1-SM-WH-(XFT) 80 CRI, 3500K EXTRUDED ALUMINUM HOUSING AND CONTINUOUS APPEARANCE FROSTED ACRYLIC FLUSH SATIN FINISH LENS.

A3E-X' FOCAL POINT - LED UNV 10W/FT 12W/FT NOMINAL 4" WIDE X 4.5" HIGH X VARYING FEET LONG SURFACE MOUNT LINEAR LED. FIXTURE CONSISTS OF 1,2,3

LOCATE EMERGENCY SECTION PER PLAN OR NEAREST TO THE PATH OF EGRESS.


OR EQUAL BY FINELITE HP4 SERIES 625 LUMNES/FT LOCATE IN LAST 4'-0" SEGMENT OF FIXTURE.

FS4ML-FL-625LF-35K-1C-UNV-LD1-X-EM-WH-(XFT) 80 CRI, 3500K OF OPERATING 10 WATTS IN EMERGENCY MODE FOR A MINIMUM OF 90 MINUTES.

A2E-X' FOCAL POINT - LED UNV 6.5W/FT 7W/FT SAME AS FIXTURE TYPE A2-X' EXCEPT WITH EMERGENCY DRIVER. EMERGENCY DRIVER SHALL BE CAPABLE 1,2,3,5


WHITE FIXTURE HOUSING FINISH. REFER TO DRAWINGS FOR FIXTURE LENGTH.

OR EQUAL BY AXIS BEAM 4 60,000 HOURS WITH INTEGRAL CONSTANT CURRENT REDUCTION. 0-10V DIMMING DRIVER. POLYESTER POWDER COAT MATTE

OR EQUAL BY FINELITE HP4 SERIES 625 LUMNES/FT CONTRACTOR TO COORDINATE CEILING CONFIGURATION WITH FINAL CEILING SPECIFICATION. FIXTURE EQUIPPED

FS4ML-FL-625LF-35K-1C-UNV-LD1-X-WH-(XFT) 80 CRI, 3500K ALUMINUM HOUSING AND CONTINUOUS APPEARANCE FROSTED ACRYLIC FLUSH SATIN FINISH LENS.

A2-X' FOCAL POINT - LED UNV 6.5W/FT 7W/FT NOMINAL 4" WIDE X 5" HIGH X VARYING FEET LONG RECESSED LINEAR LED. FIXTURE CONSISTS OF EXTRUDED 1,2,3,5

OF 90 MINUTES. X' IN MODEL NUMBER REFER TO SPECIFIC INDIVIDUAL FIXTURE LENGTHS.

OR EQUAL BY LUMENWERX V3PERL 50,000 HOURS PROVIDE BATTERY PACK IN MIDDLE 4 FT SECTION CAPABLE OF DELIVERING 1000 LUMENS FOR A MINIMUM

OR EQUAL BY FOCAL POINT, FLUSH MOUNT -FLO 800 LUMENS/FT INTEGRAL 0-10V 5% DIMMING DRIVER.

SCPLED-800-80-25-FL-X'-W-UNV-D-1-DS-B# 80 CRI, 4000K ALUMINUM HOUSING AND CONTINUOUS APPEARANCE FROSTED ACRYLIC FLUSH SATIN FINISH LENS.

A1E AXIS - LED UNV 8.8/FT 10/FT NOMINAL 2" X 3" WALL MOUNT RECESSED PERIMETER WITH FLUSH SPACKLE FLANGE, EXTRUDED 1,2,3,5

NO. TYPE VOLT WATTS VA

TYPE MANUFACTURER/MODEL # LAMPS INPUT INPUT DESCRIPTION NOTES

LIGHT FIXTURE SCHEDULE

OR EQUAL BY PHILIPS

OR EQUAL BY HUBBELL

OR EQUAL BY EATON 50,000 HOURS

WLF#-CMB-E15WCP 6000 LUMENS

VAP-6000LM-FST-WD-MVOLT-GZ10-35K-80CRI- 3500K, 80 CRI 1500 LUMENS.

F3E LITHONIA - LED UNV 50 54 SAME AS TYPE F3 WITH INTEGRAL EMERGENCY BATTERY PACK CAPABLE OF DELIVERING 1,2,3

OR EQUAL BY PHILIPS

OR EQUAL BY HUBBELL EQUIPPED WITH INTEGRAL 10% 0-10V DRIVER.

OR EQUAL BY EATON 50,000 HOURS FITTINGS (WLF#) AS REQUIRED FOR INSTALLAITON.

WLF#-CMB 6000 LUMENS AND LENS. CHAIN HUNG WITH SUSPENSION BRACKET FROM MANUFACTURER. PROVIDE WET LOCATION

VAP-6000LM-FST-WD-MVOLT-GZ10-35K-80CRI- 3500K, 80 CRI AND NSF SPLASH ZONE RATED FOR SUSPENDED APPLICATIONS. FROSTED POLYCARBONATE HOUSING

F3 LITHONIA - LED UNV 50 54 NOMINAL 54" LONG LENSED, GASKETED VAPORIGHT LINEAR LED FIXTURE UL LISTED FOR WET LOCATIONS 1,2,3

CABLES. NO SOLDERING OF SECTIONS ALLOWED. STANDARD ALUMINUM FINISH.

CUTTBALE AND SECTIONS CONNECTED TOGETHER VIA IP20 INDOOR LOCATION STYLE JUMPER/ QUICK CONNECT

OR EQUAL LUMINII MANUFACTURER PER LOCATION AND COORDINATED WITH DIMMING SYSTEM FOR FINAL COMPATIBILITY. SYSTEM TO BE FIELD

OR EQUAL BY EDGE LIGHITNG BY SECOND COURTROOM. SYSTEM TO INCLUDE REMOTE MLV TRIAC 277/ 24V DIMMING TRANSFORMER SIZED ACCORDINGLY

DRVWDIM24-300 2500LM/ FOOT 24V FOOT FOOT 85% COEFFICIENT TRANSMISSION FROSTED LENS FOR A STRAIGHT RUN WITHIN ARCHITECTURAL COVES IN

CH-AT11-F-HI-20-24-4.4-24-5-MLV/ 90+ CRI, 2,700K PRIMARY PER PER VERY WARM WHITE 2,700K LINEAR LED TAPELIGHT SYSTEM WITHIN ALUMINUM HOUSING, MOUNTING CLIPS AND

F2 ACOLYTE LED LED 277V 4.4 WATT 5 WATT NOMINAL 3/4" WIDE X 1/2" HIGH X VARYING LENGTH SURFACE MOUNTED DAMP LOCATION IP20 RATED LOW VOLTAGE 1,2,3,5

CABLES. NO SOLDERING OF SECTIONS ALLOWED. UL WET LOCATION LISTED.

CUTTBALE AND SECTIONS CONNECTED TOGETHER VIA IP67 WET LOCATION STYLE JUMPER/ QUICK CONNECT

OR EQUAL LUMINII MANUFACTURER PER LOCATION AND COORDINATED WITH DIMMING SYSTEM FOR FINAL COMPATIBILITY. SYSTEM TO BE FIELD

OR EQUAL BY EDGE LIGHITNG BY SECOND ENTRY BUMP-OUT. SYSTEM TO INCLUDE REMOTE MLV TRIAC 277/ 24V DIMMING TRANSFORMER SIZED ACCORDINGLY

DRVWDIM24-300 120LM/ FOOT 24V FOOT FOOT 85% COEFFICIENT TRANSMISSION FROSTED LENS FOR A STRAIGHT RUN ALONG TOP BUILDING BAND AND AROUND

CH-AS2-F-HI-65-24-2.2-24-6-MLV/ 90+ CRI, 2,400K PRIMARY PER PER VERY WARM WHITE 2,400K LINEAR LED TAPELIGHT SYSTEM WITHIN ALUMINUM HOUSING, MOUNTING CLIPS AND

F1 ACOLYTE LED LED 277V 2 WATT 2 WATT NOMINAL 1/2" WIDE X 1/2" HIGH X VARYING LENGTH SURFACE MOUNTED WET LOCATION IP65 RATED LOW VOLTAGE 1,2,3,5

OR PRE-APPROVED EQUAL

F5000-75-90-SD-NC HALOGEN 90 MINUTES OF OPERATION. PROVIDE WITH SELF DIAGNOSTIC.

EM CONCEALITE LED QUARTZ 120 45 50 RECESSED BUG-EYE EMERGENCY LIGHT FIXTURE WITH TWO (2) QUARTZ HALOGEN LAMPS CAPABLE OF 1,2,3

PROVIDE MOUNTING BARS AS REQUIRED.

REMOVABLE THROUGH APERTURE. DAMP LOCATION LISTED.

OR EQUAL BY AMERLUX EVOC SERIES MANUFACTURER STANDARD 0-10V DIMMING DRIVER SUITABLE FOR ENERGY SAVING 10% OF FULL OUTPUT WITH DRIVER

OR EQUAL BY GOTHAM EVO SERIES BY DOWNLIGHT WITH HIGH 90+ CRI SINGLE CHIP LED MODULE. FIXTURE FURNISHED WITH INTEGRAL 4-WIRE

927K-DN-WD-NP 3000 LUMEN REFLECTOR WITH OVERLAPPING FLANGE. FIXTURE EQUIPPED WITH INTEGRAL 60 DEGREE BEAM SPREAD

FLC4D-RO-3000L-277-LD1-BH-LC4-RD-3000L- 90 CRI, 2,700K WITH NEW CONSTRUCTION HOUSING FOR DRYWALL CEILING CONDITIONS, PROPRIETARY WARM DIFFUSE ALZAK

D8 FOCAL POINT LED LED 120 45 50 NOMINAL 4" DIAMETER APERTURE X 5-1/2" DEEP RECESSED WARM WHITE 2,700K LED FIXED DOWNLIGHT FIXTURE 1,2,3

OR EQUAL BY AMERLUX EVOC SERIES 50,000 HOURS

OR EQUAL BY FLC44D SERIES 1000 LUMENS

EVO-SQLW-WDIM-HALR/10-4AR-LSS-277 80 CRI, 3500K

D7WW GOTHAM LIGHTING - LED 277 19 21 SIMILAR TO TYPE D7 WITH LENSED WALL WASH OPTICS. 1,2,3



EVO4SQSH-35/15-4DFR-SMO-MVOLT-EZ10 80 CRI, 3500K FIXTURE EQUIPPED WITH INTEGRAL 0-10V DIMMING DRIVER. UL RATED LISTED FOR WET LOCATION.

D7W GOTHAM LIGHTING - LED 277 17 19 SIMILAR TO TYPE D7 WITH IP66 RATING, REGRESSED WIPE DOWN, SMOOTH LENS 1,2,3



EVO-SQ-35/15-4AR-LSS-277-GZ10-E10WCP 80 CRI, 3500K OF OPERATING 600 LUMENS IN EMERGENCY MODE FOR A MINIMUM OF 90 MINUTES.

D7E GOTHAM LIGHTING - LED 277 17 19 SAME AS FIXTURE TYPE D7 EXCEPT WITH EMERGENCY DRIVER. EMERGENCY DRIVER SHALL BE CAPABLE 1,2,3

OR EQUAL BY AMERLUX EVOC SERIES 50,000 HOURS FIXTURE EQUIPPED WITH INTEGRAL 0-10V DIMMING DRIVER. UL RATED LISTED FOR WET LOCATION.

OR EQUAL BY FLC44D SERIES 1500 LUMENS PROVIDE MOUNTING BARS AS REQUIRED.

EVO-SQ-35/15-4AR-LSS-277-GZ10 80 CRI, 3500K SEMI-SPECULAR FINISH. 16 GAUGE GALVANIZED STEEL CONSTRUCTION.

D7 GOTHAM LIGHTING - LED 277 17 19 NOMINAL 4" SQUARE APERTURE X 7" DEEP RECESSED LED DOWNLIGHT WITH CLEAR APERTURE AND 1,2,3

OR EQUAL BY PRESCOLITE LF4 SERIES 50,000 HOURS

OR EQUAL BY HE WILLIAMS L45 SERIES 750 LUMENS

EVO-SQ-35/15-4WH-LD-277-GZ10-E10WCP 80 CRI, 3500K OF OPERATING 750 LUMENS IN EMERGENCY MODE FOR A MINIMUM OF 90 MINUTES.

D6E GOTHAM LIGHTING - LED UNV 10 12 SAME AS FIXTURE TYPE D6 EXCEPT WITH EMERGENCY DRIVER. EMERGENCY DRIVER SHALL BE CAPABLE 1,2,3

OR EQUAL BY PRESCOLITE LF4 SERIES 50,000 HOURS FIXTURE EQUIPPED WITH INTEGRAL 0-10V DIMMING DRIVER. UL RATED LISTED FOR WET LOCATION.

OR EQUAL BY HE WILLIAMS L45 SERIES 750 LUMENS PROVIDE MOUNTING BARS AS REQUIRED.

EVO-SQ-35/07-4AR-LSS-277-GZ10 80 CRI, 3500K SEMI-SPECULAR FINISH. 16 GAUGE GALVANIZED STEEL CONSTRUCTION.

D6 GOTHAM LIGHTING - LED UNV 10 12 NOMINAL 4" SQUARE APERTURE X 7" DEEP RECESSED LED DOWNLIGHT WITH CLEAR APERTURE AND 1,2,3

OR EQUAL BY AMERLUX EVOC SERIES 50,000 HOURS FIXTURE EQUIPPED WITH INTEGRAL 0-10V DIMMING DRIVER.

OR EQUAL BY FSC44AA SERIES 1500 LUMENS PROVIDE MOUNTING BARS AS REQUIRED.

ICO -SQ-35/15-4AR-LSS-50D-277-GZ10 80 CRI, 3500K SEMI-SPECULAR FINISH. 16 GAUGE GALVANIZED STEEL CONSTRUCTION.

D5 GOTHAM LIGHTING - LED 277 17 19 NOMINAL 4" SQUARE APERTURE X 7" DEEP ADJUSTABLE LED DOWNLIGHT WITH CLEAR APERTURE AND 1,2,3

OR EQUAL BY AMERLUX EVOC SERIES MANUFACTURER

OR EQUAL BY GOTHAM EVO SERIES BY

LCS4-RD-AA-WD-NP 2,500 LUMEN

FLCS4-RO-2500L-927K-NFL-277-L11-BH- 90 CRI, 2,700K FOR A MINIMUM OF 90 MINUTES.

D4E FOCAL POINT LED LED 277 42 47 SAME AS TYPE D4 WITH INTEGRAL EMERGENCY DRIVER CAPABLE OF DELIVERING 7 WATTS 1,2,3


DRIVER REMOVABLE THROUGH APERTURE. DAMP LOCATION LISTED.

4-WIRE STANDARD 0-10V DIMMING DRIVER SUITABLE FOR LOW LEVEL DIMMING TO 1% OF FULL OUTPUT WITH

OR EQUAL BY AMERLUX EVOC SERIES MANUFACTURER MAIN BEAM CANDELA AND WITH HIGH 90+CRI SINGLE CHIP LED MODULE. FIXTURE FURNISHED WITH INTEGRAL

OR EQUAL BY GOTHAM EVO SERIES BY VERTICAL AND 360 DEGREE HORIZONTAL ADJUSTABILITY AND 25 DEGREE NARROW DISTRIBUTION YIELDING 7,000

LCS4-RD-AA-WD-NP 2,500 LUMEN ALZAK REFLECTOR WITH OVERLAPPING FLANGE. FIXTURE EQUIPPED WITH INTEGRAL MANUAL LOCKING 40 DEGREE

FLCS4-RO-2500L-927K-NFL-277-L11-BH- 90 CRI, 2,700K FIXTURE WITH NEW CONSTRUCTION HOUSING FOR DRYWALL CEILING CONDITIONS, PROPRIETARY WARM DIFFUSE

D4 FOCAL POINT LED LED 277 42 47 NOMINAL 4" DIAMETER APERTURE X 6-3/4" DEEP RECESSED WARM WHITE 2,700K LED ADJUSTABLE ACCENT 1,2,3

FOCAL POINT FLCS44 SERIES

USAI BEVELED2.1-3131 SERIES

4SQABV-CD-WHSF-WET-EMI20 3,200 LUMEN

AX4SQ A - 32LM-35K-80CRI-GZ1-277- 80 CRI, 3,500K FOR A MINIMUM OF 90 MINUTES.

D3E ACULUX LED LED 277 36 38 SAME AS TYPE D3 WITH INTEGRAL EMERGENCY DRIVER CAPABLE OF DELIVERING 20 WATTS 1,2,3

FOCAL POINT FLCS44 SERIES

USAI BEVELED2.1-3131 SERIES PROVIDE MOUNTING BARS AS REQUIRED.

4SQABV-CD-WHSF-WET 3,200 LUMEN FIXTURE EQUIPPED WITH INTEGRAL 0-10V DIMMING DRIVER. UL RATED LISTED FOR WET LOCATION.

AX4SQ A - 32LM-35K-80CRI-GZ1-277- 80 CRI, 3,500K REFLECTOR. TRIM FINISH AS DETERMINED BY ARCHITECT.

D3 ACULUX LED LED 277 36 38 NOMINAL 4" SQUARE APERTURE X 7" DEEP ADJUSTABLE LED DOWNLIGHT WITH CLEAR DIFFUSE 1,2,3

OR EQUAL BY AMERLUX EVOC SERIES MANUFACTURER

OR EQUAL BY GOTHAM EVO SERIES BY

927K-DN-WD-NP 3000 LUMEN

FLC4D-RO-3000L-277-LD1-BH-LC4-RD-3000L- 90 CRI, 2,700K FOR A MINIMUM OF 90 MINUTES.

D2E FOCAL POINT LED LED 277 45 50 SAME AS TYPE D2 WITH INTEGRAL EMERGENCY DRIVER CAPABLE OF DELIVERING 7 WATTS 1,2,3


REMOVABLE THROUGH APERTURE. DAMP LOCATION LISTED.

OR EQUAL BY AMERLUX EVOC SERIES MANUFACTURER STANDARD 0-10V DIMMING DRIVER SUITABLE FOR ENERGY SAVING 10% OF FULL OUTPUT WITH DRIVER

OR EQUAL BY GOTHAM EVO SERIES BY DOWNLIGHT WITH HIGH 90+ CRI SINGLE CHIP LED MODULE. FIXTURE FURNISHED WITH INTEGRAL 4-WIRE

927K-DN-WD-NP 3000 LUMEN REFLECTOR WITH OVERLAPPING FLANGE. FIXTURE EQUIPPED WITH INTEGRAL 60 DEGREE BEAM SPREAD

FLC4D-RO-3000L-277-LD1-BH-LC4-RD-3000L- 90 CRI, 2,700K WITH NEW CONSTRUCTION HOUSING FOR DRYWALL CEILING CONDITIONS, PROPRIETARY WARM DIFFUSE ALZAK

D2 FOCAL POINT LED LED 277 45 50 NOMINAL 4" DIAMETER APERTURE X 5-1/2" DEEP RECESSED WARM WHITE 2,700K LED FIXED DOWNLIGHT FIXTURE 1,2,3




3

3

3 03/19/19 ADDENDUM 3

FAXTEL


2 1

0 0

C

e n

t r

a l

S t . S

u i

t e 3

1 K

a n

s a

s C

i t y

, M

O 6

4 1

0 8

(O)

8 1 6. 4

7 4. 1

3 9 7 (

F)

8 1 6. 4

2 1. 8

0 2 4 w

w

w

. s

f s

a r

c h. c

o m

sfs

archite

ctu

re

© 2

014

54321

D

C

B

A


(816) 663-8700 (816) 663-8701KANSAS CITY, MO 64108

1801 MAIN, SUITE 300

WWW.HENDERSONENGINEERS.COM

C:\R

evit\P

roje

cts\

Bo

nne

r S

prin

gs P

olic

e_

ME

P_

ma

ria

un

ruh

_2

01

90

319

10

54

01.r

vt

3/1

9/2

019

10:5

8:2

5 A

M

E612

LIGHT FIXTURESCHEDULE

CIT

Y O

F B

ON

NE

R S

PR

ING

S, K

AN

SA

S

BO

NN

ER

SP

RIN

GS

GO

VE

RN

ME

NT

SE

RV

ICE

S C

EN

TER

-PO

LIC

E F

AC

ILIT

Y


ISSUE DATE: 02 / 22 /2019


20

0 E

3R

D S

T.

BO

NN

ER

SP

RIN

GS

, K

S 6

60

12

AN

DR

EA

C. M

ULV

AN

Y

1850002088KS. CORPORATE NO: E-325

EXPIRES 12/31/2020

UPLIGHT CONDITIONS.

OR EQUAL BY LUMIERE TRANSFORMER MOUNTED TO BUILDING. FIXTURE AND STAKE FURNISHED IN WRINKLE BRONZE. U.L LISTED FOR

OR EQUAL BY LUMASCAPE VOLTAGE WIRES INTO AND OUT OF STAKE FOR CONNECTION TO REMOTE 150 WATT 120V/ 12V MLV WET LOCATION

OR EQUAL BY HK LIGHTING MANUFACTURER ONLY THREADED 1/2" NPT STEM CONNECTED TO 12" DEEP COMPOSITE CONSTRUCTION HOLLOW STAKE TO ALLOW LOW

BY SECOND WEEP HOLES AND INTERNAL 30 DEGREE REFLECTOR YIELDING A NOMINAL 1,100 MAIN BEAM CANDELA. FIXTURE'S

TR-150-120 400 LUMEN 12V GASKETING FOR WATER-TIGHT INSTALLATION. LIGHT FIXTURE EQUIPPED WITH 45 DEGREE 1" DEEP BEZEL CAP WITH

DS-LED-E65-WFL-BZW-11-A/ PP-S-12-BZW/ 80 CRI 3,000K PRIMARY ADJUSTABLE UPLIGHT FIXTURE CONSTRUCTED OF MACHINED ALUMINUM WITH HIGH TEMPERATURE SILICON O-RING

S6 BK LIGHTING LED LED 120 7 9 NOMINAL 2-1/4" DIAMETER X 7" LONG SURFACE MOUNTED WET LOCATION WARM WHITE 3,000K LED LANDSCAPE 1,2,3

FOR 90 MINUTES.

OR PRE-APPROVED EQUAL 1156 LUMEN PROVIDE WITH INTEGRAL EMERGENCY BATTERY PACK CAPABLE OF DELIVERING FULL OUTPUT

IBL-4-3Q-30-BK-277 70 CRI 3,000K PERFORMACE. DIE-CAST AND LOW-IRON ALUMINUM FIXUTRE BODY WITH CONTINUOUS GASKETS.

S5AE SELUX LIGHTING LED LED 277 20 22 NOMINAL 7-15/16" DIAMETER X 48" HIGH SURFACE MOUNTED WET LOCATION WARM WHITE 3,000K LED PERFORMACE 1,2,3

OR PRE-APPROVED EQUAL 1156 LUMEN

IBL-4-2Q90-30-BK-277-EM 70 CRI 3,000K FOR 90 MINUTES.

S5E SELUX LIGHTING LED LED 277 17 18 SAME AS TYPE S5 WITH INTEGRAL EMERGENCY BATTERY PACK CAPABLE OF DELIVERING FULL OUTPUT 1,2,3

OR PRE-APPROVED EQUAL 1156 LUMEN

IBL-4-2Q90-30-BK-277 70 CRI 3,000K PERFORMANCE. DIE-CAST AND LOW-IRON ALUMINUM FIXTURE BODY WITH CONTINUOUS GASKETS.

S5 SELUX LIGHTING LED LED 277 17 18 NOMINAL 7-15/16" DIAMETER X 48" HIGH SURFACE MOUNTED WET LOCATION WARM WHITE 3,000K LED PERFORMACE 1,2,3

DIRECTED BY ARCHITECT TO MATCH ADJACENT SURFACE. UL LISTED FOR WET LOCATIONS AND IP 66 RATED.

BUILDING EXTERIOR WITH INTEGRAL 0-10V DIMMING DRIVER. FIXTURE FINISHED IN BRONZE FINISH OR AS OTHERWISE

WET LOCATION STO CORD AND GLAND FROM FIXTURE TO CONTRACTOR PROVIDED JUNCTION BOX AT FACE OF

OR EQUAL BY ACCLAIM MANUFACTURER SNOOT WITH BLACK INTERIOR FINISH AND EXTERIOR PAINTED TO MATCH FIXTURE. MANUFACTURER FURNISHED

OR EQUAL BY INSIGHT BY LED DIODE ARRAY WITH STANDARD 40 DEGREE FLOOD DISTRIBUTION AND STANDARD FULL CUT-OFF 360 DEGREE

LBGSN-BRZ-BK 5,600 LUMEN ALUMINUM FORMED YOKE, STAINLESS STEEL HARDWARE, SILICONE GASKETING, CLEAR TEMPERED GLASS FACE AND

LBG-277-30K-FL-BRZ-DIM- 80 CRI 3,000K FLOODLIGHT FIXTURE CONSTRUCTED OF LOW COPPER CONTENT DIE-CAST ALUMINUM HOUSING WITH HEAVY

S4 LUMENPULSE LED LED 277 100 105 NOMINAL 13-1/2" DIAMETER X 5-3/4" DEEP YOKE MOUNTED WET LOCATION WARM WHITE 3,000K LED PRECISE OPTIC 1,2,3

ARCHITECT TO MATCH ADJACENT SURFACE. UL LISTED FOR WET LOCATIONS AND IP 66 RATED.

WITH INTEGRAL 0-10V DIMMING DRIVER. FIXTURE FINISHED IN BRONZE FINISH OR AS OTHERWISE DIRECTED BY

CORD AND GLAND FROM FIXTURE TO CONTRACTOR PROVIDED JUNCTION BOX AT FACE OF BUILDING EXTERIOR

INTERIOR FINISH AND EXTERIOR PAINTED TO MATCH FIXTURE. MANUFACTURER FURNISHED WET LOCATION STO

OR EQUAL BY ACCLAIM MANUFACTURER DEGREE DISTRIBUTION. MANUFACTURER TO FURNISH FIXTURE WITH STANDARD CUT-OFF VISOR WITH BLACK

OR EQUAL BY INSIGHT BY LED DIODE ARRAY WITH STANDARD 60 DEGREE FLOOD DISTRIBUTION WITH ADDED LENS TO MODIFY BEAM TO 100

LBGVS-BRZ-BK 5,600 LUMEN ALUMINUM FORMED YOKE, STAINLESS STEEL HARDWARE, SILICONE GASKETING, CLEAR TEMPERED GLASS FACE AND

LBG-277-57K-WFL-100 DEGREE LENS-BRZ-DIM- 80 CRI 5,700K OPTIC FLOODLIGHT FIXTURE CONSTRUCTED OF LOW COPPER CONTENT DIE-CAST ALUMINUM HOUSING WITH HEAVY

S3 LUMENPULSE LED LED 277 100 105 NOMINAL 13-1/2" DIAMETER X 5-3/4" DEEP YOKE MOUNTED WET LOCATION VERY COOL WHITE 5,700K LED PRECISE 1,2,3

UL WET LOCATION LISTED FOR UPLIGHT CONDITIONS.

OR EQUAL BY LUMIERE CONCRETE POUR APPLICATIONS. BRONZE WRINKLE FINISH FOR FIXTURE AND VAULT.

OR EQUAL BY LUMASCAPE WITH INTEGRAL 120V/12V 20 WATT INCANDESCENT DIMMING DRIVER. VAULT EQUIPPED WITH GROUT MASK FOR

OR EQUAL BY HK LIGHTING MANUFACTURER ONLY THREADED 1/2" NPT STEM CONNECTED TO 14" DEEP GROUND RECESSED CORROSION-FREE COMPOSITE VAULT


1,100 LUMEN 12V GASKETING FOR WATER-TIGHT INSTALLATION. LIGHT FIXTURE EQUIPPED WITH 45 DEGREE 1" DEEP BEZEL CAP WITH

DE-LED-X62-FL-BZW-A/ HP2-D20INC-GM-R 80 CRI 3,000K PRIMARY ADJUSTABLE UPLIGHT FIXTURE CONSTRUCTED OF MACHINED ALUMINUM WITH HIGH TEMPERATURE SILICON O-RING

S2 BK LIGHTING LED LED 120 20 22 NOMINAL 3" DIAMETER X 10" LONG SURFACE MOUNTED WET LOCATION WARM WHITE 2,700K LED LANDSCAPE 1,2,3

UL WET LOCATION LISTED FOR UPLIGHT CONDITIONS.

OR EQUAL BY LUMIERE CONCRETE POUR APPLICATIONS. BRONZE WRINKLE FINISH FOR FIXTURE AND VAULT.

OR EQUAL BY LUMASCAPE WITH INTEGRAL 120V/12V 20 WATT INCANDESCENT DIMMING DRIVER. VAULT EQUIPPED WITH GROUT MASK FOR

OR EQUAL BY HK LIGHTING MANUFACTURER ONLY THREADED 1/2" NPT STEM CONNECTED TO 14" DEEP GROUND RECESSED CORROSION-FREE COMPOSITE VAULT


1,100 LUMEN 12V GASKETING FOR WATER-TIGHT INSTALLATION. LIGHT FIXTURE EQUIPPED WITH 45 DEGREE 1" DEEP BEZEL CAP WITH

DE-LED-X61-FL-BZW-A/ HP2-D20INC-GM-R 80 CRI 2,700K PRIMARY ADJUSTABLE UPLIGHT FIXTURE CONSTRUCTED OF MACHINED ALUMINUM WITH HIGH TEMPERATURE SILICON O-RING

S1 BK LIGHTING LED LED 120 20 22 NOMINAL 3" DIAMETER X 10" LONG SURFACE MOUNTED WET LOCATION WARM WHITE 2,700K LED LANDSCAPE 1,2,3


OR EQUAL BY FINELITE HP4 SERIES 625 LUMENS/FT REFER TO DRWAINGS FOR FIXTURE LENGTH. LENGTHS TO BE EVENLY DIVIDED.

FSM4LW-FL-625LF-35K-1C-UNV-LD1-C48-WH-X' 80 CRI, 3500K FIXTURE CAPABLE OF DELIVERING 1000 LUMENTS FOR 90 MINUTES.

P3E-X' FOCALPOINT - LED UNV 6.5/FT 7/FT SAME AS TYPE P4(XFT) WITH INTEGRAL EMERGENCY BATTERY PACK INSTALLED IN LAST 4' SEGMENT OF 1,2,3,5


OR EQUAL BY FINELITE HP4 SERIES 625 LUMENS/FT

FSM4LW-FL-625LF-35K-1C-UNV-LD1-C48-WH-X' 80 CRI, 3500K REFER TO DRWAINGS FOR FIXTURE LENGTH. LENGTHS TO BE EVENLY DIVIDED.

P3-X' FOCALPOINT - LED UNV 6.5/FT 7/FT SIMILAR TO TYPE P1 WITH DIRECT OUTPUT ONLY. 1,2,3,5

OR PRE-APPROVED EQUAL 100,000 HOURS

CLV48-WH-6'-C6 1000 LUMENS/FT

FNRS-FL40-1000LF-35K-1C-UNV-LD1-HS- 80 CRI, 3500K FROSTED ACRYLIC DIFFUSER. 40/60 DISTRIBUTION

P2-X' FOCAL POINT - LED 277 10W/FT 12W/FT 6'-0" X 7.79" WIDE X 1.60" DEEP EXTRUDED ALUMINUM WITH DIE-CAST ALUMINUM END CAPS. SUSPENDED. 1,2,3,5

OR EQUAL BY AXIS BEAM 4

OR EQUAL BY FINELITE HP4 SERIES 61,000 HOURS

C96-WH 875 LUMENS/FT REFER TO DRWAINGS FOR FIXTURE LENGTH. LENGTHS TO BE EVENLY DIVIDED.

FSM4BS-FLFL-875DN-625UP-35K-2C-UNV-LD1- 80 CRI, 3500K FIXTURE CAPABLE OF DELIVERING 1000 LUMENTS FOR 90 MINUTES.

P1E-X' FOCAL POINT - LED 277 10W/FT 12W/FT SAME AS TYPE P1(XFT) WITH INTEGRAL EMERGENCY BATTERY PACK INSTALLED IN LAST 4' SEGMENT OF 1,2,3,5

REFER TO DRAWINGS FOR FIXTURE LENGTH. LENGTHS TO BE EVENLY DIVIDED.

OR EQUAL BY AXIS BEAM 4 COAT MATTE WHITE FIXTURE HOUSING FINISH. INDIRECT AND DIRECT PORTION TO BE CONTROLLED SEPARATELY.

OR EQUAL BY FINELITE HP4 SERIES 61,000 HOURS EQUIPPED WITH INTEGRAL CONSTANT CURRENT REDUCTION. 0-10V DIMMING DRIVER. POLYESTER POWDER

C96-WH 875 LUMENS/FT CONTRACTOR TO COORDINATE CEILING CONFIGURATION WITH FINAL CEILING SPECIFICATION. FIXTURE EQUIPPED

FSM4BS-FLFL-875DN-625UP-35K-2C-UNV-LD1- 80 CRI, 3500K OF EXTRUDED ALUMINUM HOUSING AND CONTINUOUS APPEARANCE FROSTED ACRYLIC FLUSH SATIN FINISH LENS.

P1-X' FOCAL POINT - LED 277 10W/FT 12W/FT NOMINAL 4" WIDE X 5.13" HIGH X VARYING FEET LONG PENDANT INDIRECT/DIRECT LINEAR LED. FIXTURE CONSISTS 1,2,3,5

OR PRE-APPROVED EQUAL SECOND SYSTEM TO INCLUDE REMOTE POWER SUPPLY SIZED ACCORDINGLY.

PSX-100-277-24-NO-WH (AS REQUIRED) 900 LUMENS/FT 24V FIXTURE TO BE WHITE.

LOGR RO-XX-24VDC-XX-30K-10X60-UMPR-WH 80 CRI, 3000K PRIMARY 3000K LINEAR LED WALL WASH IN EXTRUDED ALUMINUM HOUSING, MOUNTING CLIPS.

F8 LUMENPULSE - LED 277V 7.5W/FT 34 2-7/16" WIDE X 1-5/16" TALL X VARYING LENGTH SURFACE MOUNTED LOW VOLTAGE 1,2,3,5

OR EQUAL BY COLUMBIA LXEM 60,000 HOURS NEMA 4X. UL LISTED FOR WET LOCATIONS.

OR EQUAL BY METALUX 4VT2 SERIES 4000 LUMENS NEMA 4X GASKET. STAINLESS STEEL (#316) LATCHES.

FEM-L48-4000LM-LPAFL-MD-277-35K-80CRI-STSL 80 CRI, 3500K ONLY ONE-PIECE 5VA FIBERGLASS HOUSING WITH INTEGRAL PERIMETER CHANNEL UTILIZING PURIND IN PLACE

F7 LITHONIA LIGHTING - LED 120 30 34 4'-0" LED STRIP FIXTURE. PENDANT OR SURFACE MOUNTED. FULLY ENCLOSED AND GASKETED. 1,2,3,5

INDICATED ON PLAN BY "-X'" IN FIXTURE DESIGNATION.

SECOND MANUFACTURER FOR COMPLETE INSTALLATION. PROVIDE MATERIALS NECESSARY FOR RUN LENGTH

OR EQUAL BY CALI 150LM/ FOOT 24V #APS-10-24, LOCATED INSIDE BUILDING. PROVIDE MOUNTING CLIPS, CLEAR LENS, AND END CAPS FROM

OR EQUAL BY Q-TRAN 95+ CRI, 2,700K PRIMARY PROVIDE REMOTE NON-DIMMING 150W POWER SUPPLY FROM MANUFACTURER,

F6-X' ACCLAIM FLX444 / FLEXOSE27 / FLX LP CL4 - LED 277V 9 10 PROVIDE FIELD-CUT LOW PROFILE FLEXIBLE CHANNEL AND IP68 RATED TAPE LIGHT. 1,2,3,5

OR EQUAL BY COLUMBIA LIGHTING

OR EQUAL BY HE WILLIAMS

OR EQUAL BY LITHONIA 50,000 HOURS CHAIN HANGER KIT FOR SURFACE MOUNTED LOCATIONS. NOMINAL 4000 LUMEN OUTPUT. WHITE FINISH.

4SNLED-LD5-41SL-LW-UNV-EL7W-L835-CD1 3500K, 80 CRI 500 LUMENS. PROVIDE WITH CHAIN HANGER KIT FROM MANUFACTURER FOR INSTALLATION. PROVIDE LESS

F5E EATON - LED UNV 34 35 4' LINEAR LED STRIP LIGHT WITH INTEGRAL EMERGENCY BATTERY PACK CAPABLE OF DELIVERING MIN. 1,2,3

OR EQUAL BY COLUMBIA LIGHTING

OR EQUAL BY HUBBELL

OR EQUAL BY HE WILLIAMS 50,000 HOURS PROVIDE LESS CHAIN HANGER KIT FOR SURFACE MOUNTED LOCATIONS. NOMINAL 4000 LUMEN OUTPUT.

OR EQUAL BY LITHONIA 3500K, 80 CRI PROVIDE WITH CHAIN HANGER KIT FROM MANUFACTURER FOR INSTALLATION.

4SNLED-LD5-41SL-LW-UNV-L835-CD1

F5 EATON - LED UNV 34 35 4' LINEAR LED STRIP LIGHT. WHITE FINISH. 1,2,3

MANUFACTURER PER LOCATION. SYSTEM TO BE FIELD CUT TO FIT FINAL CASE WIDTH.

OR EQUAL BY LUMINII BY SECOND SYSTEM TO INCLUDE REMOTE MLV TRIAC 277/ 24V DIMMING TRANSFORMER SIZED ACCORDINGLY

OR EQUAL BY EDGE LIGHTING 120LM/ FOOT 24V FOOT FOOT LENS FOR A STRAIGHT RUN WITHIN TOP DISPLAY CASE COMPARTMENT.

CH-AC3-S2-90-IP20-24V-5.0-27-2-MLV 90+ CRI, 2,700K PRIMARY PER PER WARM WHITE 2,700K LINEAR LED TAPELIGHT SYSTEM WITHIN ALUMINUM HOUSING, MOUNTING CLIPS, NO

F4 ACOLYTE LED LED 277V 5 WATT 5 WATT NOMINAL 3/4" WIDE X 3/4" HIGH X VARYING LENGTH SURFACE CORNER MOUNTED LOW VOLTAGE 1,2,3,5




OR EQUAL BY DUAL LITE LE SERIES

OR EQUAL BY PHILIPS CHLORIDE

OR EQUAL BY EATON SURELITE

EDGR-REL REFER TO DRAWINGS FOR DIRECTIONAL INDICATORS, NUMBER OF FACES AND MOUNTING.

X1 LITHONIA - LED 277 2 3 RECESSED EDGE-LIT EXIT SIGNS. RED ON CLEAR. 1,2,3

OR PRE-APPROVED EQUAL 346 LUMENS

S.6320W-UNV-01-S.6329 80 CRI, 3000K COPPER FREE. STAINLESS STEEL SCREW. RECESSED IN WALL.

W7 SISTEMALUX - LED 277 12 15 12.25" X 2.5" X 2" DEEP LED STEP LIGHT. WHITE FINISH. DIE-CAST ALUMINUM MARINE GRADE, 1,2,3

OR EQUAL BY AXIS BEAM 4 SERIES. 70,000 HOURS MINIMUM OF 90 MINUTES. WHITE FINISH.

OR EQUAL BY FINELITE HP4 SERIES 3500 LUMENS PROVIDE WITH EMERGENCY BATTERY CAPABLE OF OPERATING 1400 LUMENS IN EMERGENCY MODE FOR A

FSM4LW-FL-875LF-35K-LD1-EM-WH-4' 80 CRI, 3500K 48" LONG.

W6E FOCAL POINT - LED 277 37 41 FIXTURE SIMILAR TO TYPE P1 WITH WALL MOUNTING AND DIRECT OPTICS ONLY, FLUSH SATIN LENS. 1,2,3

OR EQUAL BY L.C. DOANE SC SERIES MOUNT AS HIGH ON WALL AS POSSIBLE WITHIN SPACE.

OR EQUAL BY CERTOLUX VRW 80,000 HRS FURNISH WITH INTEGRAL BATTERY PACK CAPABLE OF SUPPLYING 500 LUMENS FOR 90 MINUTES.

OR EQUAL BY EATON FWLDL SERIES 3700 LUMENS POWDER COAST FINISH, .125" PRISMATIC POLYCARBONATE LENS.

CC-4-0-45L35K-DCC-DV-2-1-LEL 80 CRI, 3500K HOUSING WITH CONTINUOUS WELDED SEAMS, FULLY RECESSED SCREWS, WHITE POLYESTER

W5 KENALL - LED UNV 45 50 NOMINAL 9" X 9" X 4' ANGLED WALL MOUNT HIGH ABUSE FIXTURE. SINGLE-PIECE DIE-FORMED 1,2,3


FOCAL POINT 2400 LUMENS

LP2WGF-S2-MED/80/3500-N-DG-MED/80/3500- 80 CRI, 3500K ALUMINUM HOUSING. FIXTURE TO BE WHITE AND BE PROVIDED WITH INTEGRAL DUST GUARD.

W4 ALW - LED 277 20 24 NOMINAL 2-1/4" DEEP X 4" TALL X 2'-0" LONG SURFACE MOUNTED LED VANITY FIXTURE WITH EXTRUDED 1,2,3

$900 PER FIXTURE. UL OR ETL LISTED FOR WET LOCATIONS.

WINONA LIGHTING 95 CRI FIXTURE TO BE DETERMINED BY ARCHITECT FROM PHOTOGRAPHS. CONTRACTOR TO PROVIDE AN ALLOWANCE OF

VISA LIGHTING 2700K CONTRACTOR TO PROVIDE WITH SPECIFIED LED REPLACEMENT LAMPS FROM SORAA. EXACT DIMENSIONS OF CUSTOM

OR AS OTHERWISE APPROVED BY 927-01 DIFFUSER AND FINISH TO MATCH EXISTING PHOTOGRAPHS OF ENTRY SCONCE WITH ONE (1)) MEDIUM BASE SOCKET .

CUSTOM FIXTURE 1 SA19-11-OMNI ONLY SOCKET FIXTURE WITH LED REPLACEMENT LAMP. FIXTURE EQUIPPED WITH FROSTED GLASS GLOBE STYLE

W3 LIMBURGH GLASS LED (1) SORAA 120 11 13 NOMINAL 6" DIAMETER X 12-1/2" DEEP SURFACE MOUNTED WET LOCATION CUSTOM DECORATIVE MEDIUM BASE 1,2,3

OR PRE-APPROVED EQUAL 346 LUMENS WET LOCATION LISTED.

S.6320W-UNV-14-S.6329 80 CRI, 3000K COPPER FREE. STAINLESS STEEL SCREW. RECESSED IN WALL.

W2 SISTEMALUX - LED 277 12 15 12.25" X 2.5" X 2" DEEP LED STEP LIGHT. ALUMINUM GRAY FINISH. DIE-CAST ALUMINUM MARINE GRADE, 1,2,3


N-DG-WH-UNV 4800 LUMENS

LP2WGF-S4-MED/80/3500-N-DG-MED/80/3500- 80 CRI, 3500K ALUMINUM HOUSING. FIXTURE TO BE WHITE AND BE PROVIDED WITH INTEGRAL DUST GUARD.

W1 ALW - LED 277 40 45 NOMINAL 2-1/4" DEEP X 4" TALL X 4'-0" LONG SURFACE MOUNTED LED VANITY FIXTURE WITH EXTRUDED 1,2,3

OR EQUAL BY AMERLUX

OR EQUAL BY EDISON PRICE

TR2 LSI RECESSED CONTROL TRAC NA NA 120 NA NA RECESSED FLANGLESS TRACK. WHITE FINISH. TWO CIRCUIT. 1,2,3

OR EQUAL BY AMERLUX

OR EQUAL BY EDISON PRICE

TR1 LSI RECESSED CONTROL TRAC NA NA 120 NA NA RECESSED FLANGLESS TRACK. WHITE FINISH. ONE CIRCUIT. 1,2,3

OR EQUAL BY AMERLUX

OR EQUAL BY EDISON PRICE CONTROL AND WHITE EXTERIOR FINISH AS CONFIRMED WITH ARCHITECT. 120 VOLT ONLY

W/ HOOD-CIN 3,000 LUMEN OPTICAL SYSTEM YIELDING NOMINAL 30 DEGREE BEAM FOR NOMINAL 6,000 MBCP, AND 0-10V DIMMING.

LX2084-T19-30-98-35-00-10-120- 98 CRI 3500K ALUMINUM HOUSING AND LOCKING STEM CONFIGURATION.

T2A LIGHTING SERVICES INC LED LED 120 39 42 NOMINAL 5-3/4" DIAMETER X 10" DEEP CANOPY MOUNTED WARM WHITE 3,500K LED TRACK FIXTURE WITH 1,2,3

OR EQUAL BY AMERLUX CONTROL AND WHITE EXTERIOR FINISH AS CONFIRMED WITH ARCHITECT. 120 VOLT ONLY

OR EQUAL BY EDISON PRICE FIXTURE ALSO EQUIPPED WITH EXTENDED HOOD FOR GLARE


LX2084-T19-30-98-35-00-10-120- 98 CRI 3500K ALUMINUM HOUSING AND LOCKING STEM CONFIGURATION.

T2 LIGHTING SERVICES INC LED LED 120 39 42 NOMINAL 5-3/4" DIAMETER X 10" DEEP CANOPY MOUNTED WARM WHITE 3,500K LED TRACK FIXTURE WITH 1,2,3

OR EQUAL BY AMERLUX

OR EQUAL BY EDISON PRICE WHITE EXTERIOR FINISH AS CONFIRMED WITH ARCHITECT. 120 VOLT ONLY


LX2044-T19-10-83-27-M4-00-10-120- 83 CRI 2,700K ALUMINUM HOUSING AND LOCKING STEM CONFIGURATION.

T1 LIGHTING SERVICES INC LED LED 120 11 13 NOMINAL 4-3/16" DIAMETER X 10" DEEP CANOPY MOUNTED WARM WHITE 2,700K LED TRACK FIXTURE WITH 1,2,3

OR EQUAL BY HUBBELL GEOPAK SERIESOR EQUAL BY PHILIPS GARDCO 101L SERIES

OR EQUAL BY EATON ENC SERIES 3050 LUMENS

WSQ-LED-P1-40K-SR2-MVOLT-PE-E20WC-DBLXD 80 CRI, 4000K CAPABLE OF DELIVERING 1500 LUMENS.

SW2E LITHONIA - LED UNV 20 22 SAME AS TYPE SW2 WITH INTEGRAL EMERGENCY 90-MINUTE BATTERY 1,2,3

OR EQUAL BY HUBBELL GEOPAK SERIES

OR EQUAL BY PHILIPS GARDCO 101L SERIES


WSQ-LED-P1-40K-SR2-MVOLT-PE-DBLXD 80 CRI, 4000K

SW2 LITHONIA - LED UNV 20 22 SAME AS TYPE SW1 WITH TYPE 2 DISTRIBUTION. 1,2,3




WSQ-LED-P1-40K-SR4-MVOLT-PE-E20WC-DBLXD 80 CRI, 4000K CAPABLE OF DELIVERING 1500 LUMENS.

SW1E LITHONIA - LED UNV 20 22 SIMILAR TO TYPE SW1 WITH REDUCED OUTPUT AND INTEGRAL EMERGENCY 90-MINUTE BATTERY 1,2,3



OR EQUAL BY EATON ENC SERIES 3050 LUMENS FOR WET LOCATIONS. TYPE 4 DISTRIBUTION. INTEGRAL PHOTOCELL.

WSQ-LED-P2-40K-SR4-MVOLT-PE-DBLXD 80 CRI, 4000K GASKETED DOOR FRAME. MOLDED ACRYLIC LENS WITH BLACK POWDERCOAT FINISH. LISTED

SW1 LITHONIA - LED UNV 29 31 NOMINAL 18" WIDE X 9" TALL ROUNDED WALL SCONCE WITH DIE-CAST ALUMINMUM HOUSING AND 1,2,3


ULI-21173-80W-T2-W40-01-16'-120/277V 80 CRI, 4000K 7,8

SP2 LIGMAN - LED UNV 80 90 SAME AS TYPE SP1 WITH TYPE 2 DISTRIBUTION. 1,3,6,


ULI-21173-80W-T4-W40-01-16'-120/277V-HSS 80 CRI, 4000K 7,8

SP1S LIGMAN - LED UNV 80 90 SAME AS TYPE SP1 WITH HOUSE SIDE SHIELD. 1,3,6,

BASE PLATE SHALL BE MOUNTED FLUSH WITH GRADE.

OR PRE-APPROVED EQUAL 7646 LUMENS TO SQUARE ALUMINUM POLE WITH BASE COVER, COLOR AND FINISH TO MATCH FIXTURE.

ULI-21173-80W-T4-W40-01-16'-120/277V 80 CRI, 4000K IP 65 RATING, INTEGRAL NON-DIMMING DRIVER, BLACK POWDER COAT PAINT. MOUNTS 7,8

SP1 LIGMAN - LED UNV 80 90 RECTILINEAR AREA LIGHT WITH TYPE 4 DISTRIBUTION, DIE CAST ALUMINUM HOUSING, 1,3,6,

INSTALLATION PROPOSED IN CUSTOM-FABRICATED BOLLARD PER ARCHITECT. SEE SHEET AS503.

FIXTURE INSTALLATION REQUIRES TOOL KIT RENTAL FROM MANUFCTURER.

OR PRE-APPROVED EQUAL 50,000 HOURS PROVIDE P70418-500 REMOTE 26 WATT DRIVER FROM MANUFACTURER.

750-3-3-2-2 111 LUMENS STAINLESS STEEL FINISH. 90-DEGREE ASYMMETRIC DISTRIBUTION.

S8 ALPHABET - 3000K LED 3V 1.5 2 NOMINAL 16 MM DIAMETER THINK WALL, FLAT FACE PUCK LIGHT WITH 3.5" WIRE LEADS. PROVIDE IN 1,3

TESTED FOR UPLIGHT CONDITIONS.GROUT MASK AS NEEDED FOR CONCRETE PLAZA CONDITIONS.

BRONZE FACEPLATE FINISH AND INTERNAL ACCESSORY HOLDER. UL LISTED FOR WET LOCATIONS AND

FIXTURE EQUIPPED WITH INTEGRAL 120 VOLT ONLY DIMMING DRIVER FOR TRIAC/MLV DIMMING.

CHAMBER AND WITH ADDED STABILITY FLANGE FOR CONCRETE PLAZA CONDITIONS

FIXTURE TO CONTAIN ANTI-WICKING/ ANTI-SIPHONING DEVICE TO PREVENT WATER FROM ENTERING LAMP

OR EQUAL BY LUMIERE EQUIPPED WITH INTERNAL OPTICS YIELDNG 25 DEGREE BEAM WITH 15 DEGREE VERTICAL ADJUSTMENT.

OR EQUAL BY LUMASCAPE ONLY COMPOSITE HOUSING, 1/4" THICK TEMPERED CLEAR GLASS FACE AND OVERALPPING FLANGE. FIXTURE

12-D34INC-AH/ GM-R WET LOCATION, WARM WHITE 3,000K LED ADJUSTABLE UPLIGHT FIXTUREWITH CORROSION-FREE

S7 BK LIGHTING HP2-LED-TR-X62-NFL-BZW-12 1 2000 LUMENS 120 34 35 7-1/4" DIAMETER FACEPLATE WITH 4" APERTURE X 14" DEEP GROUND RECESSED DIRECT BURIAL 1,2,3

UPLIGHT CONDITIONS.

OR EQUAL BY LUMIERE TRANSFORMER MOUNTED TO BUILDING. FIXTURE AND STAKE FURNISHED IN WRINKLE BRONZE. U.L LISTED FOR

OR EQUAL BY LUMASCAPE VOLTAGE WIRES INTO AND OUT OF STAKE FOR CONNECTION TO REMOTE 150 WATT 120V/ 12V MLV WET LOCATION

OR EQUAL BY HK LIGHTING MANUFACTURER ONLY THREADED 1/2" NPT STEM CONNECTED TO 12" DEEP COMPOSITE CONSTRUCTION HOLLOW STAKE TO ALLOW LOW


TR-150-120 400 LUMEN 12V GASKETING FOR WATER-TIGHT INSTALLATION. LIGHT FIXTURE EQUIPPED WITH 45 DEGREE 1" DEEP BEZEL CAP WITH

DS-LED-E65-WFL-BZW-11-A/ PP-S-12-BZW/ 80 CRI 3,000K PRIMARY ADJUSTABLE UPLIGHT FIXTURE CONSTRUCTED OF MACHINED ALUMINUM WITH HIGH TEMPERATURE SILICON O-RING

S6 BK LIGHTING LED LED 120 7 9 NOMINAL 2-1/4" DIAMETER X 7" LONG SURFACE MOUNTED WET LOCATION WARM WHITE 3,000K LED LANDSCAPE 1,2,3




3

3

3

3

3 03/19/19 ADDENDUM 3