acrylic bath installation general installthe bath · legal rights. applies to the uk only. ceramic...

2
INSTALLATIO N ACRYLIC BATH Tel: 0870 8505551, Fax: 0870 8505552, Website: www.kohleruk.com Kohler Mira Limited, December 2007 CHA_craddlefeet_11/12/2007 Install the Bath 1. Make sure that the bath is installed by a competent installer. 2. Before installation carefully inspect the new fixture for any signs of damage. General 1. Install the cross bar onto the bottom of the bath by feeding it through the bracket. 2. Make sure the cross bars are evenly spaced aboutthe centre of the bath and secure them inposition with the bolts. 3 4. Install the end of the steel bars onto the plastic parts. 5. Install the “V shape” onto the threaded bars. 6. Manually Tighten the nuts until the “V shape” is in full contact with the underneath of the bathtub rim and tighten a further 1/2 turn with a spanner. 7. Install and tighten the washers and nuts onto the threaded bars above the plastic parts. . Installthe feet onto the cross bars and secure them in position with the nuts. 10. If required, mark the positions of the holes forthe taps and drill with a suitable tool. Note! The positions of the mounting holes forthe taps depend on the type of bath that you are installing. The mounting holes can be at either end of the bath or on a centralledge. 11. Fitthe taps and the waste onto the bath in accordance with the manufacturer‘s instructions. Note! If the bath is to be installed with a side against a walland the bath does nothave an integralupstand, we recommend the use of a tiling-in bead. Referto the instructions packed with the tiling-in bead. Apply sealant in accordance with the manufacturer‘s instructions to sealthe bath to the surrounding structure. Complete the finished wall surface (e.g. tiling) arond the bath as required. Fillthe bath with waterand sealaround the bath edge with silicone sealant. Allow the sealant to cure before draining the bath. If necessary, install the bath panel. Refer to seperate instructions. Nuts Feet 8. Position the bath in the desired location and make sure that it is level. Adjust the feet on the bath to obtain a height of 545 mm (+ 2 mm/ - 0 mm) between the floor and the rim of the bath. 9. With the bath in position and level, secure the feet to the floor with suitable screws. 12. 13. 14. 15. 16. Connect the services to the taps and the waste. 545 mm (+2/0) end bars need to be against the rim 20 mm min 19 Bolt Cross Bar 19 plastic part steel bar threaded bar

Upload: others

Post on 19-Aug-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: ACRYLIC BATH INSTALLATION General Installthe Bath · legal rights. Applies to the UK only. Ceramic Ware and Cast Products Stainless Steel Products and Acrylic Baths Shower Valves,

INSTALLATIO N

ACRY LIC BATH

Tel: 0870 8505551, Fax: 0870 8505552, Website: www.kohleruk.com

Kohler Mira Limited, December 2007CHA_craddlefeet_11/12/2007

Install the Bath

1. Make sure that the bath is installed by a competentinstaller.

2. Before installation carefully inspectthe new fixture forany signs of damage.

G eneral

1. Install the cross bar onto the bottom of the bath byfeeding it through the bracket.

2. Make sure the cross bars are evenly spaced aboutthecentre ofthe bath and secure them inposition with thebolts.

3

4. Install the end of the steel bars onto the plastic parts.

5. Install the “V shape” onto the threaded bars.6. Manually Tighten the nuts until the “V shape” is in full contact with the underneath of the bathtub rim and tighten a further 1/2 turn with a spanner.7. Install and tighten the washers and nuts onto the threaded bars above the plastic parts.

. Installthe feetonto the cross bars and secure theminposition with the nuts.

10. If required, markthe positions of the holes forthe tapsand drill with a suitable tool.Note! The positions ofthe mounting holes forthe tapsdepend on the type ofbath thatyou are installing. Themounting holes can be at eitherend of the bath orona central ledge.

11. Fitthe taps and the waste onto the bath in accordancewith the manufacturer‘s instructions.Note! If the bath is to be installed with a side againsta walland the bath does nothave an integralupstand,we recommend the use ofa tiling-in bead. Referto theinstructions packed with the tiling-in bead.

Apply sealant in accordance with the manufacturer‘sinstructionsto sealthe bathto the surroundingstructure.Complete the finished wall surface (e.g. tiling) arondthe bath as required.Fillthe bath with waterand sealaround the bath edgewith silicone sealant. Allow the sealant to cure beforedraining the bath.

If necessary, install the bath panel. Refer to seperateinstructions.

Nuts

Feet

8. Positionthe bath inthe desired locationand make surethat it is level. Adjust the feet on the bath to obtain aheight of 545 mm (+ 2 mm/-0 mm) between the floorand the rim of the bath.

9. With the bath in position and level, secure the feet tothe floor with suitable screws.

12.

13.

14.

15.

16.

Connect the services to the taps and the waste.

545 mm(+2/0)

end bars need to beagainst the rim

20 mm min

19

Bolt

Cross Bar

19

plastic part

steel bar

threaded bar

Page 2: ACRYLIC BATH INSTALLATION General Installthe Bath · legal rights. Applies to the UK only. Ceramic Ware and Cast Products Stainless Steel Products and Acrylic Baths Shower Valves,

WC’s and BidetsCaution! Risk of product damage. Most toilet bowl cleaners are not harmful to the vitreous china surface of the toilet bowl. Please follow the bowl cleaner manufacturer’s instructions carefully.Caution! Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage.

Cast Iron ProductsKeep your cast iron product looking new by rinsing it out thoroughly after each use.

FurnitureDoor and Cabinet Care: Usually regular cleaning with a damp cloth is sufficient. Never use strong detergents or abrasive cleaners as this may damage the surface finish of your furniture.Bathroom furniture may deteriorate if subjected to heavy water spillage or prolonged condensation. Any edges that may come into contact with water must be sealed. We strongly recommend that all installations are well ventilated, failure to do so may invalidate your guarantee.Glass Care: When cleaning glass panels or mirrors, use a damp cloth with washing-up liquid or soft soap. Do not use washing powders or any other substance containing abrasives, as these will scratch the glass.

GUARANTEE OF QUALITY

CUSTOMER SERVICE

Kohler Mira LimitedCromwell Road,Cheltenham, GL52 5EP

1059476-W2-B © Kohler Mira Limited, August 2006

Kohler UK guarantee products against any defect of materials or workmanship for the following periods:

Our confidence in the quality and reliability of our superior products enables us to offer a comprehensive guarantee for all products.To register and fully benefit from this guarantee you must return the enclosed product registration card indicating the Kohler items you have purchased.Within the guarantee period we will undertake to resolve any material defects, by providing replacement parts, modules or complete product, as we deem appropriate. To be free of charge, work must be undertaken by Kohler UK approved personnel.To ensure that any problems can be promptly resolved you must contact Kohler UK directly.Proof of purchase must be provided with any claims.This guarantee covers products in domestic use, installed, operated and maintained in accordance with the instructions. It covers the purchaser only and is not transferable.

Commercial / Business UseAny Kohler Bathroom product used within a commercial / business premise is guaranteed for 1 year against any defect of materials or workmanship.

Not Covered by this GuaranteeDamage or defects arising from incorrect installation, improper use or lack of maintenance. Installed product damaged in transit, consequential loss, damage or product removal and installation costs. General wear and tear.This guarantee is in addition to your statutory and other legal rights. Applies to the UK only.

Ceramic Ware and Cast Products

Stainless Steel Products and Acrylic Baths

Shower Valves, Taps, Cistern Fittings, Toilet Seats and Bath Panels

Bathroom Furniture and Accessories

Whirlpool / Spa Baths

25 Years10 Years

5 Years2 Years

1 Year

CLEANING

GENERALMake sure that the item is installed by a competent installer.Make sure that these instructions are left with the user.

GeneralCaution! Risk of product damage. Many cleaners contain abrasive and chemical substances, and should not be used for cleaning stainless steel, enamel, plated or plastic fittings. These finishes should be cleaned using a mild washing up detergent or soap solution, rinsed and then wiped dry with a soft clean cloth.

Kitchen and Bathroom Taps and AccessoriesTel: 0870 240 7896Fax: 01242 282 595email: [email protected]: www.kohleruk.com

Showers and FittingsTel: 0870 241 0888Fax: 01242 282 595email: [email protected]: www.kohleruk.com

All other Kohler ProductsTel: 0870 850 5551Fax: 0870 850 5552email: [email protected]: www.kohleruk.com

CONTACT US

The company reserves the right to alter product specifications without notice.