accelero twin tubro ii - images-na.ssl-images-amazon.com · 6 choose the correct mounting hole size...
TRANSCRIPT
Accessories
Heatsinks
*Please use the thermal adhesive immediately once opened. You may purchase additional heatsinks and thermal adhesive at arctic.ac/TT2
Dear Customer,
Thank you for choosing the Accelero Twin Turbo II.
The Twin Turbo II is an upgrade cooler with an unparalleled cooling/noise ratio, thus does not just offer superb GPU temperatures but everything at a low noise level. A complete set of VRM heatsinks and high performance thermal glue completes this solution.
I hope you enjoy this GPU cooler and we at ARCTIC look forward to further enriching your life with our products. If you would like to share how you use ARCTIC's products please do so at https://www.facebook.com/ARCTIC.en
ARCTIC is a fully carbon neutral company and your support helps us to compensate every kilogram of CO we produce. 2
Thank You.
Sincerely,
Magnus HuberARCTIC CEO
Accelero Twin Tubro IIWelcome Guide
Spacers(2.3 mm) x 1
*Thermal Adhesive (3g)
4-pin Fan Power Adapter x 1
M2 Screwsx 4
Washersx 4
Spacers(1.5 mm) x 1
Mounting Plate x 2
Spacers(3.5 mm) x 1
Insulation Tape(0.5cm x 10cm each) x 5
x 11 x 4 x 4x 2 x 5
support.arctic.ac/TT2
ES
1
2
43
21
Main Cable Set
Pin No.
Pin 1
Pin 2
Pin 3
Pin 4
Color
Black
Red
Yellow
Blue
Description
Ground
VDC
Signal
PWM
Not cleaning circuit components thoroughly with an eraser leads to no adhesiveness of the thermal adhesive at all.
Preparation
Please ensure that the fan connector pin assignment on your VGA board is in accordance with the following table.
Apply the insulation tape onto the circuit components in order to prevent short circuit caused by RAM and VR heatsink interference.
Apply the insulation tape onto the circuit components in order to prevent short circuit caused by RAM and VR heatsink interference.
5
3
4
Insulation Tape
6
Choose the correct mounting hole size and spacers:
Please note this table is for reference only. Refer to your own VGA card holes position during installation. The updated information is available at arctic.ac/TT2.
??
43.2 mm - use43.2 mm - use
53.2 mm - use53.2 mm - use51.0 mm - use51.0 mm - use58.4 mm - use58.4 mm - use
Mounting Plate
Mounting Hole Compatible Models
43.2 mm x 43.2 mm NVIDIA GeForce:GTX 650Ti, GT 740, 6600 (GT AGP,GT, LE, DDR2)AMD Radeon:HD 4770, 2600XT, X1650 (XT, Pro), X1600 (XT, Pro), X1550, X1300 (XT, Pro)
① ① 53.2 mm x 53.2 mm
②② 51.0 mm x 61.0 mm NVIDIA GeForce:GTX 560 (Ti, SE), 550 Ti, 460 (SE)
SpacersUsed
NVIDIA GeForce: GTX 580, 570, 480, 470, 465, 8800 (GTX, GTS)
③③ 58.4 mm x 58.4 mm
NVIDIA GeForce:GTX 650, GT 640AMD Radeon: HD 7790, 7770, 6770, 5770
NVIDIA GeForce:GTS 450, 250, 240 (OEM), 150 (OEM), GT 340, 330, 320, 130 (OEM), 9800 (GTX+, GTX, GT), 9600 (GT, GSO 512, GSO), 8800 (GTS 512, GTS, GT, GS), 7950 GT, 7900 (GTX, GT, GS), 7800 (GTX 512, GTX, GT), 6800 (Ultra Extreme, Ultra, GT, GS AGP, GS, AGP, XT AGP, XT, LE)
AMD Radeon:R9 285, R9 270 (X), R7 265, 260 (X), 250 (X), 240, HD 8870,8760, 7870, 7850, 6970, 6950, 6870, 6850, 6790, 5870, 5850, 5830, 4890, 4870, 4850, 4830, 3870, 3850, X1950 (XTX, XT, Pro, GT), X1900 (XTX, XT, GT), X1800 (XT, XL, GTO)
NVIDIA GeForce: GTX 980, 970, 770, 760, 680, 670, 660 (Ti), 650 Ti Boost
Spacers2.3 mm
Spacers1.5 mm
Spacers3.5 mm
Spacers3.5 mm
Spacers2.3 mm
Spacers2.3 mm
7b7a
Apply pressure (10 sec)Voltage regulator
RAM
Tips of Applying Thermal Adhesive
Since the thermal adhesive can be applied once only, fit thecooler to the card with the heatsinks accurately positioned before you apply the thermal adhesive.
Caution: Please ensure the heatsinks are not touching any circuit components on the VGA card to avoid short circuit.
Squeeze out all the glue with pliers.
*Thermal Adhesive (3g)
Cure time
Spacers 2.3 mm /Spacers 3.5 mm /Spacers 1.5 mm
Spacers 2.3 mm /Spacers 3.5 mm /Spacers 1.5 mm
1
Example of Installing Voltage Regulator and RAM Heatsinks
1
2
3
Install the heatsinks without touching the mounting plate.
4
x 8
Heatsinks
x 1
Heatsinks
x 1
Heatsinks
x 2
Heatsinks
Installation of Accelero Twin Turbo II
Washers
M2 Screws
2
If:X: < 55 mm X: 55 mm - 65 mm X: > 65 mm
ABC
3
4 Secure this cooler onto the VGA card by partially fastening each screw from 1 to 2 to 3 to 4 with two clockwise rotations. Repeat this until you have tightened all screws. Do not completely fasten any screw in one step.
M2 Screws1122
33
44
Thermal CompoundIf the cooler has to be installed a second time, we highly recommend using the MX-4 thermal compound from ARCTIC. Only this compound guarantees optimal performance in combination with the surface of our heatsinks.
WarrantyThis ARCTIC product includes a six-year limited warranty. For further information, please consult warranty.arctic.ac
© 2014 ARCTIC Switzerland AG. All Rights Reserved.No part of this manual including the products described in it, may be reproduced, transmitted, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purpose, without the express written permission of ARCTIC Switzerland AG. In no event shall ARCTIC its directors or employees be liable for any indirect damages, incidental or consequential damages arising from any defect or error in this manual or product.
Like us on facebookwww.facebook.com/ARCTIC.en