a.a.g. stucchi light management app user manual

A.A.G. StucchiLight Management App User Manual

Eng

Rev. 0

TABLE OF CONTENTS

PRESENTATION1.1 TECHNICAL CHARACTERISTICS OF A DALI CIRCUIT1.2 THE DALI SIGNAL1.3 TYPICAL INSTALLATION:1.4 CONNECTIVITY WITH THE ONETRACK PROGRAMMING SYSTEM1.5 ELECTRICAL CHARACTERISTICS1.6 CASAMBI MODULE USER AND INSTALLATION MANUAL

ANDROID APP2.1 INSTALL THE APPLICATION WITH THE “APK” FILE2.2 USING THE ANDROID ONETRACK PROGRAMMER APP2.3 MAIN SCREEN

DALI LAMP BRIGHTNESS CONTROL 3.1 CHANGING THE BRIGHTNESS CONTROL ADDRESS3.2 GROUP MODE BRIGHTNESS CONTROL

DALI LAMP CONFIGURATION PAGE4.1 SEARCH LAMPS4.2 SEARCH UNADDRESSED LAMPS4.3 CLEAR LAMP4.4 CLEAR LIST LAMPS4.5 MODIFY LAMPS ADDRESS 4.5.1 Aborting the new address assignment procedure4.6 TEST ON/OFF LIGHT4.7 CONFIGURE GROUP LAMPS 4.7.1 Clear Lamp Into Group 4.7.2 Test Lamps On Group (1..2..3..4) 4.7.3 Assigning a lamp to a group4.8 LAMP PROPERTIES 4.9 BOOTLOADER SERVICE 4.9.1 Checking the OneTrack module update

pag. 3pag. 3pag. 4pag. 5pag. 6pag. 6pag. 6

pag. 7pag. 7pag. 7pag. 7

pag. 11pag. 11pag. 13

pag. 14pag. 16pag. 17pag. 19pag. 20pag. 21pag. 23pag. 24pag. 25pag. 27pag. 27pag. 27pag. 29pag. 30pag. 32

1

2

3

4

1 PRESENTATION

This manual describes the operation of the DALI protocol compatible programmer for managing, installing and servicing networks controlled by the Casambi module and other objects capable of connecting to a bus of this type.

Modern lighting system cannot be limited to simply turning lights on and off. Lighting systems today are an integral element of the comfort of a location and its power management, a consideration which has given rise to the DALI (digital addressable lighting interface) control standard.

DALI is the outcome of a collaboration within the lighting industry and establishes a shared standard for the industry as a whole. DALI is thus not a system, but rather defines an interface for digital communications between a control module and the various electronic power supplies. It has therefore been included in EN 60929 for electronic power supplies as Annex E4, thus ensuring interchangeability between electronic PSU's made by different manufacturers.

A.A.G. Stucchi has developed a tool for configuring the Dali network during installation of the lighting equipment, called the ONETRACK Programmer.The programming tool, intended for System Integrators, scans the devices connected to the bus and handles or re-addresses them. This programming tool includes Android and iOS apps which guide the user in his use of the system.

9.5 V - 22.5 V, typically 16 V

Max. 250 mA (depending on the installed DALI supply power)

Data bitrate 1200 baud

L17L27L3/N = Three-phase power 16A/440VD+/D- 2x1A/50V FELV AC (DALI)

1.1 TECHNICAL CHARACTERISTICS OF A DALI CIRCUIT

3www.aagstucchi.it

DALI Voltage

DALI system current

A.A.G. Stucchi Light Management App User Manual

4www.aagstucchi.it

1.2 THE DALI SIGNAL

IDLE IDLE

MSB

833us 416us

Start LSB Stop Stop

1 1 1 1 10 0 0 0

The data is transmitted on the bus over the wires marked “D+” and “D-“.The “Idle” (standby) voltage is described in the above table.When data is sent over the bus, connected DALI systems receive a pulse train similar to the following:

This information contains the address to which the data is being sent.

The electrical signal is generated by the programmer and generates the data by shorting the 2 signals: “D+” and “D-“.

Interfacesaddess01011011

Interfacesinfo

00111011

DALIsignal

DALIcable

DALIinterfaces

DALIcontrollers


5www.aagstucchi.it

1.3 TYPICAL INSTALLATION

We show a typical installation below.

PROGRAMMING OF UPTO 64 LIGHTING FIXTURES

ProgrammingApp

Tablet

Tablet

Tablet

Smartphone

PATENT PENDING

MANAGEMENT

PROGRAMMING

Casambi App

ManagementApp

Smartphone

Smartphone

Sync via cloud


6www.aagstucchi.it

1.4 CONNECTIVITY WITH THE ONETRACK PROGRAMMING SYSTEM

1.5 ELECTRICAL CHARACTERISTICS

The ONETRACK programmer has been developed to support the Android and iOs platforms.

1.6 CASAMBI MODULE USER AND INSTALLATION MANUAL

Nominal input Voltage

Input voltage Range

Frequency

Power

Current

Ambient operating temperature

Max Output power

Output Channel

Output Voltage

Output current in short circuit

V AC

V AC

Hz

W

A

100-240

90-264

50/60

W

0.025 – 0.06

0 to +40°C

5 - 7 Watt

1

18 - 18.5 V DC

250 mA

Dedicatdhardware

DALI system current

ELECTRICAL CHARACTERISTICS

To configure the app - download the manual from: www.aagstucchi.it


7www.aagstucchi.it

2.1 INSTALL THE APPLICATION WITH “APK” FILE

Download the .apk file from www.aagstucchi.it.Now open the Download folder into which the you downloaded thw APK file.Select the file and follow the prompts to install the app by pressing Avanti (Next), Installa (Install) and Fine (End)in sequence.

2.2 USING THE ANDROID ONETRACK PROGRAMMER APP

When you have installed the Light Management app, you will find the following icon on your device's screen:.

2.3 MAIN SCREEN

This section presents the main screen and its functions

Select About in the menu to display information about the app:

Launch the application. We will now review its functions and how to use them.

2 ANDROID APP


8www.aagstucchi.it

Select BootLoader Service to enable the firmware update function, which allows us to reprogram the ONETRACK module (we will cover this later).

Select Connect, or tap the Connect icon to scan for installed modules, which are displayed in a table.


9www.aagstucchi.it

Select the module you wish to connect by tapping on it; this launches the connection between your smart device and the ONETRACK module.

Once the connection has been established, the following displays will appear:

If the module does not have a factory password, the following screen will prompt for a user password.


10www.aagstucchi.it

The following main page functions are available:

Disconnects from ONETRACK(you can also tap on the icon to do so)

Enters the DALI Setup page(you can also tap on the image to do so)

Disconnect controller

Setup DALI controller

Dimming Light

Check Firmware UpDate

Diagnostic DALI Bus

Change Password

About

Enters the Dimmer page(you can also tap on the image to do so)

This function interrogates the ONETRACK module and warns you if its firmware needs updating.

This function opens a session which displays the voltage of the DALI bus and the current draw of the connected DALI modules in real time.

This functions a session in which you can change the module's name and programming password.

We obtain information about the app


11www.aagstucchi.it

You can now use the functions to control the DALI devices.

3 DALI LAMP BRIGHTNESS CONTROL PAGE

This section explains how to set the brightness of the lamps in broadcast or single point mode, using the 64 addresses available with the DALI protocol.

Let's review the touch screen functions:

Tap the icon

The lamp whose address is shown above the icon switches to maximum

brightness; if you tap on it again,the lamp turns off.

Indirizzo Lampada 3

Drag the cursor

The lamp whose address is shownabove the icon changes brightness.

Drag the cursor

All the lamps connected to theDALI bus change brightness.

3.1 CHANGING THE BRIGHTNESS CONTROL ADDRESS

A DALI address can be assigned to each individual control so that the brightness of all lamps on the bus can be controlled.Up to 64 lamps can be controlled, per the DALI protocol specification.To do this, we select the menu options:

Set Address A

Set Address B

Set Address C

Set Address D

Dimming Group Lamp

Return to MainPage


12www.aagstucchi.it

Each option corresponds to a single control; select the option to open the page for changing the control's address:

Use “+” to increment and ”-“ to decrement the value of the address.

The address management keys are disabled when the controls are being used.


13www.aagstucchi.it

Select the option Dimming Group Lamp to enable brightness control by groups.The ONETRACK system can handle up to 4 separate groups of lamps.

As above, you can control the brightness of each group by tapping on the 4 bulb icons, or withthe slider control.

3.2 GROUP MODE BRIGHTNESS CONTROL

In this section we will see how to set the brightness of the lamps in broadcast and group mode.

To return to the previous session and control the lamps individually, select Dimmer Single Lamp; to return to the main page, select Return To Main Page.i


14www.aagstucchi.it

4 DALI LAMP CONFIGURATION PAGE

This section explains how to configure and manage the DALI bus and the connected lamps.

As explained in the main section, to enter the configuration section, simply tap on the icon:

The following interface displays:

Here we can manage the installation of a DALI lamp system, test the on/off controls, and configure logical and group addresses.


DALI Bus

1

2

21

40 54 63

15www.aagstucchi.it

To return to the main page, select Return To Main Page.

Let's take a closer look at these functions.

The menu is structured as follows:

Lamps Property

Locate Lamps

Return to Main Page

Modify Lamps Address

Test On/Off Light

Configure Group Lamps

Search Unandressed Lamps

Search Lamps

Clear Lamp

CleaList Lamp

Queries the status and configuration of the lamp.

The system searches for lamps which have a logical address - which are therefore already configured.

This option deletes the selected lamp from the bus.

This option deletes all lamps on the bus.

This option replaces the logical address assigned during the scan.

This option visually locates the lamp.

This search is slower since it scans randomly to obtain a response from the devices.The system now assigns addresses to the devices in increasing order from 0 to 63.

The system searches for lamps which have not been installed and configured on the DALI bus.

This DALI function groups a set of logical addresses into a single group address.

Lamp group configuration service.

Lamp location service - turns all lamps on the bus on and off automatically.


16www.aagstucchi.it

The DALI protocol has 64 logical addresses (“0” to “63”), so that up to 64 lamps can be installed(per the Dali specification).

4.1 SEARCH LAMPS

When this option is selected, the application will search for all previously addressed and configured lamps on the bus.

This search only scans previously assigned addresses.

Select Stop Searching Lamps to stop the scan.


17www.aagstucchi.it

4.2 SEARCH UNADDRESSED LAMPS

When this option is selected, the application will search for any lamps on the bus which have NOT been addressedand configured.

An unconfigured DALI device responds to the dimming command in broadcast mode only; no access requests are considered since the device does not have a logical address.This scan is slower than the previous one; the system first scans for devices on the bus to check for active logical addresses, and then scans for unaddressed devices.When the application finds a new device, it assigns it a free logical address in increasing order.

The service displays as follows:


18www.aagstucchi.it

When the scan terminates, the following message displays:

For each new logical address it assigns, the system flashes the lamp for one second.To return to the main page, select Return To Main Page.


19www.aagstucchi.it

4.3 CLEAR LAMP

When this option is selected, the application sends the delete command over the bus and the selected lamp's logical address is cancelled.You must first select the lamp to delete its logical address.

The application will prompt you to confirm the deletion option.

If you then want to re-install the lamp, use the Search Unaddressed Lamps option

Press No to abort the operation.Press Yes to delete the lamp.


20www.aagstucchi.it

If you then want to re-install the lamp, use the Search Unaddressed Lamps option

4.4 CLEAR LIST LAMP

This option deletes the addresses of all scanned lamps, and sends the delete command for all listed lamps overthe bus.

Select Clear List Lamps

The application will prompt you to confirm the deletion option.

Press No to abort the operation.Press Yes to delete the lamp.


21www.aagstucchi.it

4.5 MODIFY LAMPS ADDRESS

This option allows you to modify the logical addresses assigned to the listed lamps during the scan.

Select Modify Lamps Address to display a new list of lamps in the positions assigned during the scan.

The menu changes, and Modify Lamps Address is replaced by List Lamps Address.

To edit an address, select a lamp and follow the instructions:


22www.aagstucchi.it

Now choose a free address (free addresses are marked “n Free”, where “n” is the unassigned address).

The lamp is now displayed in the new position with its new address.

Select No to quit the procedure, and Yes to update the list with the address change code “<*>” assigned to the selected lamp, as shown below.


23www.aagstucchi.it

4.5.1 Aborting the new address assignment procedure

If you have selected the wrong lamp, simply select it again and follow the prompts:

Select List Lamps Address to return to the list of individual lamps.


24www.aagstucchi.it

4.6 TEST ON/OFF LIGHT

This option allows to you identify which lamps have been addressed and their locations, by turning them on at maximum brightness.

Select Test On/Off Light to display a new list of lamps in the positions assigned during the scan.

Select a lamp to display the on/off test option.

Items which display (n) Free are unassigned addresses.


25www.aagstucchi.it

4.7 CONFIGURE GROUP LAMPS

This option enables you to group sets of lamps on the Dali bus together, so that they can be controlled using a single group address.The DALI protocol provides for up to 16 groups of lamps, but the application is limited to 4 groups.A group can be represented graphically as follows:

Select Configure Group Lamps to run a service which reads the configuration of the DALI network.


Addr1 2 3 4 5 6

Addr

Addr23 24 30 33 41 45

12 14 15 16 17 18Group 0

Group 1

Group 2

Scans for lamps in existing groups.Search Lamps Into Group

Clear Lamp Into Group

Test Lamps on Group 0




Return To Main Page

Turns a group of lamps on and off

Deletes a lamp from a group

4.7.1 Clear lamp into group

This option displays:

As shown in the picture to delete a lamp from a a group simpy press the lamp itself for a few seconds.

26www.aagstucchi.it

Once the configuration has been scanned, the following options are available:


27www.aagstucchi.it

4.7.2 Test lamps on group (1..2..3..4)

Select an option to run the guided procedure for turning the group of lamps on and off.

4.7.3 Assigning a lamp to a group

Proceed as follows:

To return to the main page, select Return To Main Page.

Select the lamp as shown in the figure by pressing it for a few seconds.

The lamp is now marked with “<*>”.

Now select the menu option Memo Lamp into Group (1..2..3..4).


28www.aagstucchi.it

To abort the procedure, simply select Abort Assign Group Procedure or touch the lamp marked “<*>” again.


29www.aagstucchi.it

4.8 LAMP PROPERTIES

This option displays the lamp's factory settings.Simply select the option, select a lamp and wait for the system read its properties.


30www.aagstucchi.it

4.9 BOOTLOADER SERVICE

AAG Stucchi products are continually evolving, and our firmware and software can be updated to ensure that they are compa-tible with the full range of commercial products.

This option allows you to update the firmware of the A.A.G. ONETRACK module.

When you launch the app, as described in par. 2.3 the following menu will display, which provides access to the module update page.

To update the module, press Connect Controller.


31www.aagstucchi.it

Now press Download to start the update.Wait for the update to terminate.Press OK to return to the main page.

You will be prompted to turn the ONETRACK module off and back on again, since the update service only initiates during the first 5 seconds after power on, after which the programming app executes.Shut off power to the programmer, and wait 10 seconds to ensure that it has turned off completely.After 10 seconds, press OK on the app and power the ONETRACK module back on again.

The application will automatically connect to the update routine and display the following interface:


32www.aagstucchi.it

The following message will display:

The update procedure is now complete.

4.9.1 Checking the ONETRACK module update

To make sure the update was successful, connect to the ONETRACK module and select Check Update.

Always check that the ONETRACK module's firmware is up to date when you install a new version of the app.


A.A.G. STUCCHI s.r.l. u.s.Via IV Novembre 30/32, 23854 Olginate (LC) - ITALYPh. +39-0341-653111Fax [email protected]

A.A.G. STUCCHI NORTH AMERICA, INC.3400 Peachtree Road NE, Ste 945 Atlanta, GA 30326 - USAPh. +1-404-806-5399Fax [email protected]

A.A.G. STUCCHI ASIA PACIFIC LTD.Regional officeRoom 01, 11/fl., New Treasure Centre N° 10 Ng Fong Street, Kowloon - HONG KONGPh. +852-2578-8988Fax [email protected]

A.A.G. STUCCHI SHANGHAI LTD. Rm 3007, №738, Chang Yang Rd YangPu area, 200082 - SHANGHAIPh. +86-21-52389291Fax [email protected]

a.a.g. stucchi light management app user manual

Documents