a6: team rallye potable water still presented by: mike mcconnell november 2, 2006 nicole del rey...
TRANSCRIPT
A6: Team RallyeA6: Team RallyePotable Water StillPotable Water Still
Presented by:Presented by:Mike Mike
McConnellMcConnellNovember 2, November 2,
20062006Nicole Del Rey Mike McConnell Tim Rodts Eric
Sabelhaus
Project StatusProject Status
Project StatusProject Status
Design StatusDesign Status Power (…being assembled…)Power (…being assembled…)
Pedals Pedals Intermediate Gears Intermediate Gears Generator Generator Heat Source (assembled and tested)Heat Source (assembled and tested)
Heating bowl Heating bowl Sand Sand Baby bottle Baby bottle Condensing (assembled and tested)Condensing (assembled and tested)
Tygon tubing, 2Tygon tubing, 2ndnd baby bottle (tested well) baby bottle (tested well) Intelligence (show-stopper)Intelligence (show-stopper)
Temperature Sensor with DisplayTemperature Sensor with Display WebsiteWebsite
Semester OutlookSemester OutlookAssignments Prototype Other
19-Sep Trade study proposals submitted Website createdConcept memo submitted
26-Sep Preliminary cost estimation Determine intelligence functionsOrder nichrome wire
3-Oct Order generatorOrder polymerOrder sensorsOrder structural material
10-Oct Trade studies completed Order air pumpOrder pressure valvesProgram microcontroller
17-Oct24-Oct Manufacture polymer Initial CAD Assembly developed
Test heat sourceTest air pump
31-Oct Build structureTest pressure valves
7-Nov Assemble electronics, sensors, valves14-Nov Install components
Test fully operating prototype16-Nov Draft design doc. completed21-Nov Prototype demonstration28-Nov Concept design review5-Dec Design documentation due
!!
In the works
Show StoppersShow Stoppers IntelligenceIntelligence
Temperature sensor needsTemperature sensor needs Electrical connectionsElectrical connections Water proofingWater proofing Computer programmingComputer programming
Generator – Sprocket connectionGenerator – Sprocket connection Purchase a sprocket with set-screwPurchase a sprocket with set-screw Machine a part to interfaceMachine a part to interface
Action Items Action Items from last weekfrom last week
(Week 10)(Week 10)
-1--1- TASK: Order Bearings for Intermediate GearsTASK: Order Bearings for Intermediate Gears
ACTION:ACTION: Obtained gear system from a different bicycleObtained gear system from a different bicycle Gears already on a rotating shaftGears already on a rotating shaft Eliminates need to purchase bearingsEliminates need to purchase bearings Gear system has been installed in prototypeGear system has been installed in prototype
-2--2- TASK: Order a coupler to attach the generator shaft to TASK: Order a coupler to attach the generator shaft to
an adjacent shaft which rotates on bearings to absorb an adjacent shaft which rotates on bearings to absorb radial loadsradial loads
ACTION:ACTION: Contacted Windstream Power (generator manufacturer)Contacted Windstream Power (generator manufacturer) Learned that generator can support radial loadsLearned that generator can support radial loads Decided to directly drive the generator shaftDecided to directly drive the generator shaft Eliminates need for coupler, 2 additional bearingsEliminates need for coupler, 2 additional bearings
-3--3- TASK: Create CAD TASK: Create CAD
modelsmodels ACTION:ACTION:
Action Items Action Items for this weekfor this week
(Week 11)(Week 11)
-1--1- TASK: Prepare Temperature SensorTASK: Prepare Temperature Sensor
ACTION:ACTION: Consult Mr. Brownell to see if current temperature Consult Mr. Brownell to see if current temperature
sensors are usablesensors are usable Connect wires to sensor OR order new sensorsConnect wires to sensor OR order new sensors Begin programmingBegin programming
-2--2- TASK: Create 3-Way InterfaceTASK: Create 3-Way Interface
Generator output wire/Voltmeter leads/Female outletGenerator output wire/Voltmeter leads/Female outlet
ACTION:ACTION: Purchase wire capsPurchase wire caps Obtain and cut extension cordObtain and cut extension cord Attach proper connectionsAttach proper connections Seal with electrical tapeSeal with electrical tape Voltmeter
To heating element
-3--3- TASK: Create driveshaft/sprocket interfaceTASK: Create driveshaft/sprocket interface
ACTION:ACTION: Purchase a sprocket with set-screw (Windstream, Purchase a sprocket with set-screw (Windstream,
McMaster-Carr)McMaster-Carr) Design and machine any necessary interfacing Design and machine any necessary interfacing
partpart
Questions?Questions?