a of 58719
TRANSCRIPT
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 1 of 154
Lot Item Code Item Description Target Specifications Yes No L001 0001\1 Digital Camera [1] 3 megapixel CCD [2] 3 x optical zoom [3] 3 x digital zoom, minimum [4] Movie mode up to card capacity [5] LCD screen [6] Lithium rechargeable battery (1 set) and
mains charger
[7] USB2.o connection [8] Built in flash [9] Includes 1 x 256 mb memory card [10] Includes wrist strap, software and case [11] Supplied with additional 128mb memory
card
L001 0001\2 Video Camera [1] Recording on DVD-R and DVD-RW [2] Video Actual: 640K Pixels minimum [3] Optical Zoom: 8X [4] Focusing: Auto & Manual Focus [5] LCD screen [6] Accessory Shoe [7] Video Input/Output [8] Audio Input/Output [9] USB 2.0 interface [10] Stereo Mic. Input [11] Software OS Compatibility: XP
Professional
[12] Weight: max 600g (without disc and battery)
[14 Includes 10x 30-minute rewritable recording media
[13] Including a suitable tripod [14] Including a Carry case [15] Including a set of rechargeable batteries [16] Including Mains charger L001 0001\3 Data Projector [1] Portable LCD projector [2] Built-in speaker [3] 2000 ansi lumens [4] 350:1 image contrast ratio [5] Fan noise maximum 30dB [6] 1.2 zoom factor [7] Video input : RGB, S-video, composite
video
[8] Digital video format: DTV [9] Lamp life: 2000 hours [10] Locking device [11] Password protection [12] Carry case
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 2 of 154
Lot Item Code Item Description Target Specifications Yes No L001 0001\4 Video Recorder [1] 4 video head stereo VHS with 19 micron
heads
[2] DVD+RW/+R, DVD-RW/-R and CD-R/RW playback
[3] VHS and S-VHS playback [4] DVD+RW/R, DVD-RW/RD writing
capacity
[5] Dubbing from VCR to DVD or DVD to VCR
[6] i.LINK@interface for DV/digital camcorders
[7] Variable bit rate recording [8] Remote control with multi-band TV
control
[9] Accessories: audi/video cable, power cable, 75ohm coaxial cable, AA batteries, instruction manual
L001 0001\5 Electronic Whiteboard System
WHITEBOARD
[1] Hard surface with brackets for wall and ceiling mounting
[2] Screen diagonal 1500 cm approx. [3] Supplied with pointer/electronic pen and
full accessories
[4] Ability to control application by touching screen DATA PROJECTOR
[5] 350:1 image contrast ratio [6] Built in speaker [7] 1.2 zoom factor [8] Video input : RGB, S-video, composite
video
[9] Fan noise 30dB [10] Projection range: up to 10 m [11] Digital video format: DTV [12] Lamp life: 2000 hours
WORKSTATION
[13] Replacement desktop computer with minimum 3 GHz Pentium 4 or equivalent processor
[14] 15'' TFT Display [15] 512 MB RAM [16] Minimum 60 GB HDD [17] Dedicated video adapter with 32MB
video memory
[18] DVD/CD-RW integrated combo drive [19] Audio interface integrated [20] Integrated 802.11 b/g wireless and
10/100 Mbps network controller
[21] Installed software: Windows XP, projection application software
[22] Colour printer
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 3 of 154
Lot Item Code Item Description Target Specifications Yes No TRAINING
[23] Includes installation and training L001 0001\6 Flipchart Stand [1] A1 capacity on easel [2] Fitted with paper hanging device [3] Adjustable height [4] Whiteboard surface [5] 10 rolls x A1 white plain flipchart paper x
10 rolls
[6] Marker pens - 10 pack, assorted colours [7] Whiteboard pens - 10 pack, assorted
colours
[8] Cleaning fluid [9] Eraser L001 0001\7 Display Board [1] Interlocking collapsible mobile panel
display system
[2] 6 panels each 900mm x 600mm minimum
[3] 2 headpanels 250mm x 600mm minimum [4] Carrying bag [5] Includes materials for fixing materials to
display boards
[6] System capable of expansion with the addition of further panels
L001 0001\11 Dictation Machine [1] Hand-held voice recording and playback system
[2] Digital operation [3] Capacity 15 hours minimum [4] With filing system and edit facilities [5] USB connection L001 0001\12 Comb Binder [1] For manual binding/bunching of 80g A4
paper
[2] Punch capacity 8 sheets minimum [3] Supplied with 500 comb spines in
assorted sizes and colours for A4 binding.
L001 0001\13 Office Trimmer [1] Melamine-faced or metal baseboard with guide rail
[2] Cutting width 660mm [3] Self-sharpening tungsten steel cutting
wheel
[4] Automatic clampstrip [5] Cut capacity 2 mm [6] Paper size - up to A2 L001 0001\14 Office Guillotine [1] Self-sharpening stainless steel blade [2] Safety guard and paper guide [3] Blade latch [4] Paper guides - A4, A5, A6 [5] Ruler calibrated in cm [6] Cutting width 300mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 4 of 154
Lot Item Code Item Description Target Specifications Yes No L001 0001\15 Laminating Machine [1] Photo quality [2] Hot roller technology [3] Variable temperature with electonically
controlled heat settings
[4] Cold function [5] 1 hour shut-off [6] Rejector anti-jam facility [7] Exit tray [8] A3 size [9] Pouch thickness 2 x 75 - 2X 125 microns [10] Heat up time - 5 mins [11] Speed (mm/min) 330 mm/min [12] 100 gloss pouches x 250 microns x 100
x 76mm (badge)
[13] 200 gloss pouches x 200 microns x A4 size
[14] 200 gloss pouches x 100 microns x A5 size
L001 0001\16 Business Planning Software
[1] Software to support the preparation of a business plan and marketing planning
[2] Windows XP compatible [3] Includes sample business plans and
built-in market researc
[4] Step-by-step financial guidance [5] Legal tools and funding guidance [6] Allows imports from MS Office [7] Allows generation of "what-if" cash flow
scenarios
[8] Includes sample marketing plans and SWOT analysis tool
[9] built-in graphic forecaster [10] Automatic chart generation [11] Allows importsfrom other packages [12] Facility for market demographics
analysis
L001 0001\17 Charting And Drawing Software
[1] Windows XP compatible
[2] To create diagrams, charts, graphs and illustrations
[3] Includes ready-made templates and specialised symbols for: flowcharts, organisation charts, Gantt charts, data flow diagrams, network diagrams, fishbone diagrams, phase diagrams and quality control charts
[4] With drag and drop facility L001 0001\19 CD Writer [1] External CD writer [2] Reads, writes and rewrites CD media [3] Reads DVD media [4] 48x CD write speed
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 5 of 154
Lot Item Code Item Description Target Specifications Yes No [5] 24x CD rewrite speed [6] USB connection L001 0001\20 Resuscitation Model -
Training System [1] Full-body resuscitation training mannekin
[2] To demonstrate resuscitation techniques [3] Shows expansion and contraction of
chest cavity
[4] Integrated recorder for objective performance evaluation
[5] Signal light box [6] Disposable airways L001 0001\21 Health And Safety
Videos [1] Set of materials covering the following topics:
[2] Fire safety [3] Manual handling and lifting [4] Control of dangerous substances and
those hazardous to health
[5] Personal protective equipment [6] Electrical safety [7] General workplace safety [8] Avoiding slips, trips and falls [9] DVD, CD or video format L001 0001\23 Instrument Drawing Set -
For Blackboard [1] Aluminium T-square 100 cm
[2] Aluminium square 30°/60° 50 cm [3] Aluminium square 45°/45° 50 cm [4] Aluminium protractor 180° 50 cm [5] Aluminium compasses 75 cm L001 0001\25 Stencils [1] Letter stencil set, size 5mm, 7mm, 10
mm, normal and italic
[2] Set of 6 circular stencils L001 0001\26 Technical Drawing
Software [1] Runs on Windows OS
[2] Suitable for engineering technical drawings, including sketches, layouts and electrical diagrams
[3] Library of symbols and toolsets [4] In-place text editing, automatic snap and
lock facilities
[5] Webpage compatibility L001 0001\27 Business Decision-taking
Simulator [1] To train junior managers in decision-taking techniques
[2] Replicates a manufacturing business [3] General areas covered: business
appreciation, objectives, finance & management, marketing, product mix, teamworking, presentations and operations
[4] Includes trainers pack L002 0002\1 Welding Trainer [1] Welding process: MIG,TIG & MMA
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 6 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Target patterns: inncludes drag, 7mm
stitch, 7mm weave
[3] Type of weld joints: butt, lap & inside corner
[4] Bead size 12.7mm [5] Arc length tolerance 8mm to 3mm [6] Angle limits 60 to 90° L002 0002\3.1 MIG Welding Set [1] Current: 35 to 350 Amps [2] Wheel-mounted, separate wire feeder [3] Output @ 60% duty cycle - 250 Amps [4] Open circuit voltage - 17 to 39V [5] Weldable wire sizes - 0.8 - 1.2mm [6] Output power settings - 24 [7] Wire drive wheels - 4 [8] Includes accessory kit L002 0002\3.2 DC Welding Rectifier
Type 1 [1] Electronically controlled, fan cooled, wheel mounted
[2] Dinse plug, hot start, anti stick circuit [3] Current range - 15 to 250 Amps [4] Infinitely variable electronic control L002 0002\3.3 DC Welding Rectifier
Type 2 [1] Electronically controlled, fan cooled, wheel mounted
[2] Dinse plug, hot start, anti stick circuit [3] Current range - 15 to 350 Amps [4] Infinitely variable electronic control L002 0002\4 MMA Welding Machine [1] Current range: 13Amp - 500Amp [2] Open circuit voltage - approx.85 V [3] Mains Supply - 380V/3-phase [4] Class H insulation [5] Supplied with accessory kit and remote
control unit
L002 0002\5 TIG Welding Set AC/DC [1] Current range - 6 to 160 Amps AC/DC [2] Duty cycle @ 60% - 96 Amps [3] Tungsten electrode Size - 1.0 to 2.4mm, [4] Open circuit voltage - 70V AC & 63V DC [5] Complete with TIG torch [6] Remote control facility L002 0002\6 Inverter Welding
Machine [1] Current range - 5 to 150 Amps
[2] DC output current [3] Duty cycle @ 60%: 120 Amps [4] Open circuit voltage: approx 55 V L002 0002\7 MMA Welding
Electrodes, type 1 [1] Primarily for horizontal / vertical / overhead welding
[2] Vodex 2.5mm x 350mm x 16.5kg [3] Vodex 3.2mm x 450mm x 22.2kg [4] Vodex 4.0mm x 450mm x 22.2kg
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 7 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Vodex 5.0mm x 450mm x 22.2kg L002 0002\8 MMA Welding
Electrodes, type 2 [1] Primarily for downhand welding.
[2] Super Fastex 3.2mm x 350mm x 13.2kg [3] Super Fastex 4.0mm x 450mm x 17.7kg [4] Super Fastex 5.0mm x 450mm x 17.4kg L002 0002\9 Tungsten Electrodes [1] Low carbon steel 2.4mm x 5kg [2] 18/8 - 308L 2.4mm x 5kg L002 0002\10 MIG Welding Wire [1] Bostrand LW1 0.8mm x 15kg [2] Bostrand LW1 1.0mm x 15kg L002 0002\11 Portable Flame Cutting
Machine [1] Single blowpipe - 240V
[2] Saffire 300 Series 1 ec regulator A-1.5 [3] Saffire 300 Series 1 ec regulator O-10 [4] Cutting nozzle A-Nm 1/32" [5] Cutting nozzle A-Nm 1/16" [6] Cutting nozzle A-Nm 3/32" L002 0002\12 Portable Pipe Cutting
Machine [1] Suitable for making right-hand and bevel cuts up to 45°
[2] Oxygen and gas hoses to be metal braided
[3] Range from 150mm to 1200mm OD pipe [4] Chain to be up to 1200mm [5] Materials thickness: 5mm to 50mm L002 0002\13 Accessories For Pipe
Cutting Machine [1] Single-stage, 2 gauge oxygen regulator
[2] Single-stage, 2 gauge acetylene regulator
[3] ANM cutting nozzles 0.8, 1.6 & 2.4 mm or equivalent
L002 0002\14 Portable Spotwelder [1] Output @ 50% - 2 kVA [2] Continuous output - 1.4 kVA [3] Standard arms L002 0002\15 Kit Of Electrodes [1] Arms with electrodes - L=500mm [2] Arms with electrodes - L=250mm x
200mm
L002 0002\16 Pedestal Spotwelding Machine
[1] Power @ 50% duty cycle = 15kVA
[2] Max. electrode force DAN @ 9 Bar = 250 [3] Max. open circuit voltage = 2.9 Volts [4] Max. electrode stroke = 50mm [5] Throat depth variable from 440mm to
150mm
L002 0002\17.1
Gas Welding And Cutting Set
[1] Welding up to 25mm - cutting up to 50mm.
[2] Welding shank and mixer with 4 welding nozzles
[3] Cutting attachment with 2 cutting nozzles [4] Multi stage oxygen and acetylene 2
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 8 of 154
Lot Item Code Item Description Target Specifications Yes No gauge regulators
[5] 10 metres Oxy/Acet hose with fittings [6] Combination spanner [7] Spindle key [8] Tip cleaners in Ali case with file [9] Spark lighter [10] 2 Adaptors for USA and European
regulators
[11] Welding goggles with clear & colour lenses.
L002 0002\17.2
Twin Welding Gas Cylinder Trolley
[1] Suitable for oxygen & acetylene cylinders
[2] Solid rubber tyres [3] Fitted with safety retaining chains L002 0002\17.
3 Flip Front Gas Welding Goggles
[1] Fitted with 50mm coloured and clear glass cover
[2] With anti-mist backing lens L002 0002\18 Electrode Drying
Equipment [1] Drying oven
[2] Heated electrode quiver L002 0002\19 Accessories For Welding
Workshop [1] Dinz cable socket and plug: 25 - 50mm
[2] 400 Amp earth clamp [3] CC11 screw type earth clamp [4] CC 7 cable lugs [5] Chipping hammer [6] 600 Amp electrode holder [7] 3-row wire brush [8] Anti-spatter spray L002 0002\20 Gas Regular Set [1] Saffire 300 series 1ec regulator 0 -10 [2] Saffire 300 series 1ec regulator A - 1.5 [3] Saffire 300 series 2+ regulator 0 - 10 [4] Saffire 300 series 2+ regulator A - 1.5 L002 0002\21 Oxygen And Acetylene
Hose [1] Blue hose 10 x 5m 3/8" Fittings
[2] Blue hose 10 x 10m 3/8" Fittings [3] Red hose 10 x 5m 3/8" Fittings [4] Red hose 10 x 10m 3/8" Fittings L002 0002\22 Hose Fittings [1] Nipple 10mm hose 3/8" BSP nut [2] Nut coupling 3/8" LH [3] Nut coupling 3/8" RH [4] 10x 10mm Hose O-clips [5] Hose coupler equal 3/8" LH [6] Hose coupler equal 3/8" RH L002 0002\23 Accessories For Welding
And Cutting Outfit [1] Spark lighter - Qty 5
[2] Regulator spanner - Qty 5
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 9 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Outfit spanner - Qty 5 [4] Spindle key - Qty 5 [5] "O" clip pliers - Qty 3 [6] Nozzle cleaners - Qty 5 [7] Cylinder trolley - Qty 3 [8] Gas economiser - Qty 2 [9] Chipping hammer - Qty 10 [10] 3-row wire brush - Qty 10 [11] Portable welding screen - Qty10 [12] 18"/90° blowpipe - Qty 10 [13] ANM cutting nozzles - Qty 8 [14] PNM cutting nozzles - Qty 8 [15] Acetylene gouging nozzles - Qty 8 [16] Acetylene flame cleaning heads - Qty 8 [17] Propane flame cleaning heads - Qty 8 [18] AHT heating nozzles - acetylene - Qty 5 [19] Propane super heating nozzles - Qty 5 L002 0002\24 Saffire [1] Copper coated, mild steel welding rods
2.4mm x 5kg
L002 0002\25 Welding Tables [1] Gas & arc welding bench [2] Approx. dimensions: 750 x 465 x 825mm
- W x D x H
[3] Facility for fume extraction at table level [4] Half of worktop area 30mm refractory
brick lining
[5] Other half of work area 2mm steel plate. L002 0002\27.
1 Workshop Welding Curtain And Frame
[1] Minimum area 1.25 x 1.8 m
[2] Self-supporting steel frame L002 0002\27.
2 Mini Fume Extractor [1] Self-contained and portable
[2] Extraction rate: 150 cubic metres per hour
[3] 3m flexible extraction hose L002 0002\28 Self Contained Fume
Extractor [1] Single phase, 16 A rating
[2] Extraction rate: 1200 cubic metres per hour
[3] 3m extraction arm [4] Noise level 67 dBA maximum @ 4m [7] 4 castor wheels, 2 braked L002 0002\29 Welders Angle Clamps [1] 150mm angle jig and fixture clamp [2] 225mm angle jig and fixture clamp L002 0002\30 3-Piece Locking Welding
Clamp [1] 200mm bending clamp
[2] 225mm welding clamp [3] 275mm locking C-clamp
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 10 of 154
Lot Item Code Item Description Target Specifications Yes No L002 0002\31 Angle Grinder [1] 115mm diameter disc [2] 750 W motor [3] Carrying case [4] Side handle spanner and wheel flanges [5] 10x metal cutting discs [6] 10x metal grinding discs L002 0002\33 Welders Safety Wear [1] Flip top welding helmet [2] Leather gauntlet gloves [3] Leather full-length apron L002 0002\34 Fitters Working Tool Kit [1] Marking awl [2] Steel rule 300mm x 30mm [3] Tin snips 250mm long [4] Hacksaw frame, adjustable for 250 -
300mm blades
[5] 10 compatible blades [6] Set of files comprising [7] 255mm bastard cut hand file with wooden
handle
[8] 255mm second cut hand file with wooden handle
[9] 255mm smooth cut hand file with wooden handle
[10] 203mm smooth cut square file with wooden handle
[11] 203mm smooth cut round file with wooden handle
[12] 203mm smooth cut half-round file with wooden handle
[13] 203mm smooth cut hand file with wooden handle
[14] 203mm smooth cut 3-square file with wooden handle
[15] Tap and die set M3 to M12 ISO thread (a) Hand taps: taper, second and plug (b) Dies, die-stock and tap wrench
[16] Minimum 5-piece screwdriver including 3 plain slot size 100x 5.0, 100x 6.0 and 150x 8.0mm. 2 cross point, no 1 and 2.
[17] Minimum 8-piece hexagon key set, contents: 1.5, 2.0, 2.5, 3.0, 4.0, 5.0 and 6.0mm with ring
[18] Combination pliers 160mm approx [19] Tinsmiths shears, straight bladed &
curved blade
[20] Diagonal side cutters 130mm approx [21] Engineers ball pein hammer, weight
approximately 350g
[22] Plastic hammer [23] Minimum 5 piece chisel and punch set
containing: flat cold chisel, 2 parallel pin punches, 1 taper pin punch, centre punch.
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 11 of 154
Lot Item Code Item Description Target Specifications Yes No [24] Minimum 8 piece open end wrench set
6x7, 8x9,10x11, 12x13, 14x15, 16x17, 18x19, 20x22mm
[25] Minimum 8 piece offset ring wrench set 6x7, 8x9,10x11, 12x13, 14x15, 16x17, 18x19, 20x22mm
[26] Box-end wrench set 8 to 19mm [27] Pipe wrench, stillson pattern 280mm [28] High capacity steel fitters tool box L002 0011\1 Plumber Tool Kit [1] Set of tools in high capacity steel fitters
tool box
[2] Marking awl [3] Steel rule 300mm x 30mm wide [4] Tin snips 250mm long [5] Hacksaw frame, adjustable for 250 to
300mm blades
[6] 10x compatible blades, various TPI [7] Set of 6 files, approx. 200 to 250mm
long: single cut flat rough file, flat fine double cut file, square fine double cut file, round fine double cut file, semi-round double cut fine file and rectangular double cut fine file
[8] Tap and die set M3 to M12 ISO thread, HSS in wooden case, hand taps, taper, second and plug, dies, die-stock and tap wrench
[9] Minimum 5 piece screwdriver set to include 3 plain slot size 100 x 5.0, 100 x 6.0 and 150 x 8.0mm. 2x cross point, no 1 and 2
[10] Minimum 8 piece hexagon key set, contents: 1.5, 2.0, 2.5, 3.0, 4.0, 5.0 and 6.0mm with ring and wallet
[11] Combination pliers 160mm approx [12] Hand cutting machine with straight and
curved blade
[13] Minimum 8 piece open end wrench set 8, 10, 11, 12, 13, 14, 17 and 19mm
[14] Box-end wrench set 8 to 19mm L002 0011\2 Plastic Pipe Cutter [1] Tool with 3x rotating roller metal disc
bades
[2] Overall length of tool approximately 25cm [3] Threaded adjustable diameter of hook to
cut pipe from diameter 2.0 to 25 cm
L002 0011\3 Adjusting Pliers For Pipes, 45°
[1] Used for gripping steel pipes
[2] Approximate length of tool 35 cm [3] Made of chrome or stainless steel [4] Claw-shaped pinchers, angled at 45
degrees to the handle
[5] Distance between minimum and maximum of jaw is 1.0 to 25cm
L002 0011\4 Adjusting Pliers For Pipes, 90°
[1] Used for gripping steel pipes.
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 12 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Approximate length of tool 35 cm [3] Made of chrome or stainless steel [4] Claw-shaped pinchers, angled at 90
degrees to the handle
[5] Distance between minimum and maximum of jaw is 1.0 to 25 cm
L002 0011\5 Manual Device For Bending Copper Pipes
[1] For copper pipes of 12-28 mm diameter
L002 0011\6 Welder's Set [1] Pliers for gripping electrodes whilst welding: jaw diameter from 0.1 to 0.5cm
[2] Welding helmet [3] Hand-held welding mask [4] Welding goggles [5] Welding cables compatible with welding
electrodes
[6] Accessories for electric welding L002 0011\7 Compressor [1] Tank capacity: 150 litres [2] Maximum air pressure: 8 to 9 bar [3] Air flow rate: 380l/min L002 0011\8 Mini Excavator With
Direct Cup [1] Used to dig ground for external pipe installations in narrow spaces
[2] Rubber tracks [3] Bucket capacity up to 0.1 cubic meter L002 0011\9 Oxy-Acetylene Welding
& Cutting Set [1] Oxy-acetylene welding and cutting set
[2] A complete set of welding and cutting torches including: medium duty welding torches welding capacity 0.9 mm. to 6 mm; 6 sizes of welding tips, 2x for each size; cutting torch and tips with cutting capacity 3 to 50mm; heating tip, flow rate of 500 litres/min; cutting attachments for straight cut and curve cutting and wrenches, tip cleaner and spark lighter
[3] Flash back arresters for both oxygen and acetylene lines
[4] Pressure regulators: one for oxygen and one for acetylene.
[5] A pair of hoses with connectors, length min. 5 m.
[6] Trolley, steel tube structure, for carrying gas cylinders and gas welding & cutting accessories
[7] Acetylene cylinder valve wrench. L002 0011\10 Portable Welding
Transformer [1] With heating plate/electrofusion
[2] For polyethylene, polypropylene L002 0011\11 Portable Welding Panel [1] Used to shield the welder from the heat [2] Rectangular metal construction, approx.
1.8 x 2.0m
[3] Supported on legs
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 13 of 154
Lot Item Code Item Description Target Specifications Yes No L002 0011\12 Portable Fume Extractor [1] Wall-mounted fume extraction fan [2] Airflow: 1900 cu m/h [3] Two self-supporting extraction arms [4] Rigid aluminium arms with swivel joints,
3m
[5] Supplied with 180mm dia flexible hose, 3m
L002 0011\13 Welders Working Bench [1] Gas & Arc Welding Bench [2] Dimensions 750 x 460 x 800mm approx. [3] Fume extraction facility at table level [4] Electrode holder [5] Coppered working surface L002 0011\14 Arc Welding Set [1] Current range 55 to 300 A [2] Electrode size 2.0 to 3.25 mm,or
equivalent
[3] Open circuit voltage 220/250 V [4] With handle and wheels set [5] Supplied with welding cables, electrode
holder, hand mask and combination chipping hammer.
L002 0011\15 Welding And Cutting Set [1] Welding up to 25mm - cutting up to 50mm.
[2] Welding shank and mixer with 4 welding nozzles
[3] Cutting attachment with 2 cutting nozzles [4] Multi stage oxygen and acetylene 2
gauge regulators
[5] 10 metres Oxy/Acet hose with fittings [6] Combination spanner [7] Spindle key [8] Tip cleaners in case with file [9] Spark lighter [10] 2 Adaptors for USA and European
regulators
[11] Welding goggles with clear & colour lenses.
L002 0011\16 Welding Safety Equipment
[1] Welding helmet
[2] Hand held welding mask [3] Welder apron [4] Welding googles [5] Welding gloves L002 0011\17 Electrodes For Electric
Welding [1] Dimensions: 2.5; 3.25; 5mm
[2] Length 250 to 300mm L002 0011\18 Wire For Oxyacetylene
Welding [1] Metal wire 4mm diameter
L002 0011\19 Resin-cored Solder For Copper Soldering
[1] Soft solder Lp5
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 14 of 154
Lot Item Code Item Description Target Specifications Yes No L002 0011\20 Combi Boiler [1] Combination boiler for hot water system
and central heating
[2] Gas pressure 20mbar [3] Hot water flow 11 litres/minute [6] Power output: 24 kW L002 0011\21 Electric Boiler [1] Capacity 100 litres [2] Wall mounted [3] Power rating: 2kW min. L002 0011\22 Spirit Level [1] Graduated glass tube [2] Mounted on 500mm support L002 0011\23 Pressure Valve [1] Made of brass [2] Diameter 1/2 " [3] Maximum pressure 10 bar L002 0011\24 Water Meter [1] Flow 20 l /minute [2] Domestic meter used in Romania L002 0011\25 Gas Meter [1] Gas meter used in Romania [2] Domestic fittings L002 0011\26 Angle Grinder [1] 115mm diameter disc [2] 750 W motor [3] Carrying case [4] Side handle spanner & wheel flanges [5] 10x metal cutting discs [6] 10x metal grinding discs L002 0011\27 Manual Pipe Threading
Tool [1] With pipe-cutting dies: 6 to 50mm
L002 0011\28 Electric Pipe Threading Tool
[1] With pipe-cutting dies: 6 to 50mm
[2] 750W motor approx. L002 0011\29 Flaw Detector [1] Portable device todetect pipe installation
defects
[2] Depth: up to 15m L002 0011\30 Rotary Percussion Drill [1] Speed, variable approx. 0 to 2500 rpm [2] Drilling capacity in steel up to 13mm [3] 3-jaw geared chuck and key for drills [4] Locking trigger double pole switch [5] Double insulated [6] Approx. 3-m-rubber covered cable [7] In carrying case L002 0011\31 Pipe Cutter [1] For cutting brass, copper and lead tubes [2] Fitted with fast cutting high speed wheels
and round metal handle
[3] For pipes 6 to 25mm diameter L002 0011\33 Hydraulic Pipe Bending
Machine [1] For cold pipe bending
[2] With stand and former head attachments for pipes 12 to 50mm diameter
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 15 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Supplied complete with hydraulic
powerpack
L002 0011\34 Spark Lighter [1] Suitable for acetylene and propane butane
[2] Friction type [3] Approx. 25 spare flints for each lighter L002 0011\35 Ventilation And Air-
Conditioning Tool Kit [1] Set of marking, measurement and inspection tools:metal ruler, set of precision squares, compasses, tracing needles and protractor set
[2] To include cutting tools and devices: saw for metals, left and right hand sheet shears, anvil set, riveting hammer, foot operated guillotine, laying-out table, straightening table, electric hand shears, plain soldering iron and hammer set
L002 0011\36 Bidet [1] Sanitary porcelain [2] Horizontal stand [3] With mixer taps and drain L002 0011\37 Air Conditioning System [1] Split type air condition for either floor or
ceiling installation
[2] Cooling capacity not less than 25,000 BTU/Hr
[3] Automatic temperature controlled [4] Condensing Unit: rotary or piston type
compressor using R-22 refrigerant, with overload protection and time delay
[5] Fan Coil Unit: floor or ceiling type evaporator, with adjustable air flow direction and 3-speeds
[6] Room thermostat and speed control of fan installed on wall
L002 0011\38 Set Of Bathroom Sanitary Wear
[1] Sanitary objects: hand basin, lavatory (WC), bath, bidet, small wash basin for WC
[2] Pipes: PEX, PP, PB of 16 mm diameter, total length 25 metres
[3] Fittings: sufficient selection of elbows, Tee pieces, adaptors, traps and 110mm dia. flexible hoses
[4] Fixtures: single-lever mixer taps for all units, flexible shower fitting
L002 0011\39 Basin [1] Sanitary porcelain with taps and drain [2] For assembly and dissembly [3] Width 600 mm L002 0011\40 Lavatory [1] Sanitary porcelain [2] Lateral outflow [3] With flush tank and all fittings L002 0011\41 Shower Tub + Shower
Cabin [1] Shower tray: acrylic glass fibre, dimensions 80 x 80cm
[2] Shower cubicle: plastic walls [3] Hydromassage panel L002 0011\42 Bath [1] Bath, acrylic glass fiber 1.5 m
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 16 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Hydromassage system L002 0011\43 Fitting Set [1] For fitting exercises [2] Elbows 1/2" and 16 mm [3] Tee pieces 1/2" and 16 mm [4] Angle fittings with wall bearing 1/2" and
16 mm
[5] Female adaptor 1/2 " and 16 mm [6] Flexible traps [7] Flexible 110 mm diameter pipes for
sanitary evacuation
L002 0011\44 Carbon Monoxide Detector
[1] Natural gas 20 mbar
L002 0011\45 Gas Pressure Regulator [1] Diameter 1" [2] Pressure 0.2 to 0.05 mbar L002 0011\46 Fire Drencher [1] Non-automatic sprinkler head, without
water stored in pipes
[2] Water supply pipe diameter of approximately 1.25 cm with 1/2" thread
[3] Brass sprinkler head and screw fitting [4] Activates at approximately 70°C L002 0011\47 Digital Thermostat [1] Temperature range: +10 to 100°C [2] Connected to a circulating water bath to
ensure constant sample temperature for temperature-sensitive analysis
L002 0011\48 Insertion Tongs For Copper, Manual
[1] Manual press liner
[2] Vice clamp set: 16 to 25 mm L002 0011\49 Insertion Tongs For
Copper, Electric [1] Electric press liner
[2] Vice clamp set: 16-25 mm [3] Power supply: 500 watt L002 0011\50 Insertion Tongs For
Polyropylene, Manual [1] Manual press liner
[2] Vice clamp set: 16 to 25 mm L002 0011\51 Insertion Tongs For
Polyropylene, Electric [1] Electric press liner
[2] Vice clamp set: 16 to 25 mm [3] Power supply: 500W L002 0011\52 First Aid Kit [1] To include: 1 guidance card, 40
individually wrapped plasters, 9 sterile dressings - medium, 3 sterile dressings - large and 6 triangular bandages
[2] Also to include: 4 sterile eye pads, 12 safety pins and 2 pairs of disposable gloves
[3] Wall-mounting box L002 0011\53 Set of Safety Equipment [1] Safety helmets [2] Resistant googles [3] Dust mask [4] Ear defenders
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 17 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Protective gloves [6] One size overalls L002 0011\54 Installation Samples [1] Set of samples for installation for
plumbing, air-conditioning and gas fitting
[2] Bending profiles [3] Metal and plastic pipes [4] Elbows, drain cocks and Tee pieces [5] Valves, protective and safety devices [6] Accessories for sanitary fittings [7] Auxiliary materials: dowels, screws,
brackets
L002 0011\56 Technical Construction Sets
[1] Set of exercises covering equipment, technologies and design features involved with plumbing and including operation sheets
L002 0011\57 Set Of Transparencies [1] Set of transparencies covering equipment, technologies and design features involved with plumbing
[2] Modern equipments [3] Modern technologies [4] Modern materials [5] Design features L002
0011\58 Videos/CD sets [1] Set of audio-visual media covering equipment, technologies and design features involved with plumbing
[2] To include sections on protection of labour, fire prevention, health and safety rules, environment protection, emergency resuscitation, material retraining, toxic substances and flammable liquids
L002 0011\59 Metallic Manometer [1] Measurement range: 0-16 bar L002 0011\60 Manual Pressure Pump [1] Capacity 25 bar L002 0011\62 Thermometer [1] Temperature range: 0 to +150°C [2] With a 25 mm circular gauge [3] Stainless steel stem with a minimum
length of 90mm
[4] Supplied with protection sheaf L002 0011\63 Fire Sprinkler [1] Branch diameter 1/2" [2] Evacuation hole diameter 10mm [3] Made of brass [4] Bulb activation: 70°C L003 0003\1 Pneumatics &
Electropneumatics [1] Experimental unit for investigating pneumatics, electropneumatics and PLC devices
[2] Classroom compressor, power supply units, set of electrical cables with 4mm safety plugs, grid to mount components
[3] Plug-in system for: 5/2 way valves with selector; 3/2 way normally open; 3/2-way valves normally closed; Bourdon tube
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 18 of 154
Lot Item Code Item Description Target Specifications Yes No pressure gauge, range of indication 0-10 bar, 3/2-way roller lever valves, normally closed; 3/2-way roller lever valves with idle return, normally closed
[4] Also includes: 5/2-way pneumatic double pilot valves; 5/3-way pneumatic double both sides, normally closed; dual pressure valves (AND logic function valve) block of three separate AND valves; shuttle valves (OR logic function valve) block of three separate OR valves; 5/2-way pneumatic single pilot valves; one-way flow control; quick exhaust valves; vacuum generator and suction cup; pressure sequence valves
[5] To include: vacuum-controlled valves, single-acting cylinder; double-acting cylinder piston rod;on/off valve with filter regulator; 40m polyurethane tubing and connectors; time delay valves, normally closed; 3/2-way solenoid valves normally closed; manifold with quick plug-in locking; 5/2-way single solenoid valves, 5/2-way double solenoid valves; 5/3-way double solenoid valves, normally closed
[6] To include proximity sensor, capacitive; proximity sensor, inductive; proximity sensor, optical; electronic proximity sensor; limit switch, left actuated via trip cams; pneumatic-electric converter; limit switch, right mechanically actuated by a roller lever with spring return and wiring possibilities-normally open, normally closed or changeover contact
[7] To include tubing cutter; electrical input signal device with illuminated push-buttons and integrated optical indicators
[8] To include time relay unit for switch-on delay and 1 timer relay for switch-off delay, each relay with 2 normally open and 2 normally closed contacts; relays with 4 changeover contacts; emergency stop button optical display
[9] Circuit drawing and simulation software for pneumatics and electropneumatics
[10] 1x PC with Windows operating system L003 0003\2 Hydraulics &
Electrohydraulics [1] Experimental unit for investigating pneumatics, electrohydraulicsand PLC devices, with the following components
[2] Mounting system system for: pressure gauges, flow control valves; one-way flow control valves; shut off valves; non-return valves; Tee connectors; pressure relief/pressure sequence valves; pressure relief valves; 3-way pressure reducing valves; non-return valves, delockable; double-acting cylinders with control cam; bi-directional hydraulic motors; flow dividing
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 19 of 154
Lot Item Code Item Description Target Specifications Yes No valves; shut-off/counterbalancing valves
[3] To include loading weights for simulating a driving or tractive load; 4/2-way valves; 4/3-way valves with closed mid-position; 4/3-way valve with relieving mid-position; 2-way pressure compensated flow control valves; 4/3-way valve with recirculating mid-position, all hand lever operated All valves should be
[4] Includes: pressure switch; 4/2-way solenoid valves with spring return with manual override; 4/3-way solenoid valves, with closed mid-position with manual override; 4/3-way solenoid valves, with relieving midposition; 4/3-way solenoid valves with recirculating midposition
[5] Includes: proximity sensors, inductive, capacitive and optical diffuse operation with built-in protective circuit against polarity reversal, overload, and short circuit; limit switches, actuated from left and right both with mechanically actuated micro switch, actuated by a roller lever, with spring return and wiring possibilities - normally open, normally closed or changeover contact
[6] Includes: relays, 3 fold, each relay with 4 changeover contacts; electrical input signal devices with illuminated push-buttons; time relay units, two fold, each relay with 2 normally open and 2 normally closed contacts and adjustable time delay
[7] To include electrical cables with 4mm safety plugs, equipment tray for storing components, power supply unit, 10 litres of hydraulic oil, hose line of different lengths, hydraulic power pack
[8] Circuit drawing and simulation software for hydraulics and electrohydraulics
[9] 1 PC with Windows operating system L003 0003\3 Training Module For
Self-Study [1] Suitable for use in the classroom and for self-study
[2] Workbook: hydraulics- practical exercises with supplementary notes, worked examples and data sheets
[3] Workbook: electro-hydraulics - practical exercises with supplementary notes, worked examples and data sheets
[4] Workbook: pneumatics - practical exercises with supplementary notes, worked examples and data sheets
[5] Workbook: electro-pneumatics - practical exercises with supplementary notes, worked examples and data sheets
[6] Transparency set [7] Magnetical symbols - 1 set for pneumatic
and hydraulic
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 20 of 154
Lot Item Code Item Description Target Specifications Yes No [8] Cutaway model set of pneumatic
components
L003 0003\4 Training Module for PLC [1] For study of controls pneumatics and hydraulics process with PLC and connection of sensors and actuators to PLC I/Os
[2] Set includes: input/output data cable with IEEE 488 connectors
[3] Interface to convert 16 input signals and 16 output signals into serial data for RS-232 interface
[4] Programmable logic controller; integrated clip or plug-in adapters, 12 inputs / 8 outputs - status indicated by LED's; inputs - optional PNP or NPN switchable; RS232 programming interface or ethernet; programming software included
[5] Universal connection unit connecting all 4mm plugs with the IEEE 24-pin system connector; inputs: 3 safety sockets for each input for 8 x 3-wire sensors; outputs: 2 safety sockets for each output for 8 actuators [6] PC data cable RS232
[7] PLC with Ethernet interface adaptable for industrial applications to allow several controllers to be interconnected
[8] I/O cable with SysLink connector compatible with pneumatics and hydraulics equipment
[9] Software for 3D process simulation and modular production system
[10] 1 PC with Windows operating system L003 0003\5 Robot Workstation for
Mechatronics & Production Engineering
[1] Robot station to include industrial robot with drive unit, programmable cable and teachbox
[2] AC servo motors with Harmonic Drive gear unit
[3] Absolute encoder [4] Number controlled axis: 5 [5] Handling capacity: max. 2 kg [6] Drive Unit - 64-bit RISC processor,
multitasking operating system
[7] Contour control - PTP, linear and circular interpolation
[8] Programming languages - Melfa Basic IV, Movemaster Command
[9] Number of programs approx. 90 [10] Assembly station to work with Robot
station to supply assembly process
[11] Trolley, fully assembled control console with operating panel, communication panels, spare panel and membrane keypad start pushbutton with sockets for connection to PLC
[12] Programming cable, RS232 level
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 21 of 154
Lot Item Code Item Description Target Specifications Yes No converter for use with all products with TTL-RS232 interfaces
[13] Programming, testing, commissioning and service using software
[14] Workpiece set consisting of components for assembly and dissembly
L003 0003\6 Transducer Trainer [1] Workstation for experimentation on transducers
[2] To include sets of weights, signal switching unit, pressure distributor/manifold; double acting cylinder; 3/2-way panel mounted valve normally open, on/off valve with filter regulator; canalogueonnection unit; distributor unit; measuring bridge amplifier for voltage supply and signal amplification of sensors with strain gauges; force sensor; backpressure sensor; pressure distributor/manifold; pneumatic-electric converter, pressure switch; analogue pressure sensors
[3] Set of flexible electrical cables with 4mm safety plugs
L003 0003\7 Industrial Processing Model/Simulation
[1] Training unit to consist of:
[2] Conveyor module [3] Diffuse sensor to detect workpieces
placed on the conveyor
[4] Level sensor [5] Sensor to detect the workpiece properties [6] Valve terminal [7] Short-stroke cylinders [8] On/Off and emergency switch [9] Can be controlled from PC or PLC L003 0003\8 PIC Trainer Experimental system designed around
microcontroller (PIC) and have a programming area and 10 pre-wired applications
[1] PIC16C84 with program and data EEPROM memory.
[2] 20-key keypad [3] Reset switch [4] Six 7-egment displays. [5] Ten LED's. [6] Connectors for providing all port A lines
as inputs, all port B lines as outputs, output for connection of solid state relay and for connection to parallel printer port of PC
[7] RS232 connectors and cable for PC. [8] Buzzer [9] All software, including: Microchip
Technology's MPASM cross assembler software and PC based PIC programming software
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 22 of 154
Lot Item Code Item Description Target Specifications Yes No [10] A series of at least 10 experiments, with
their program listings, based on the PIC Trainer's pre-wired circuits, using the PIC16C84 EEPROM microcontroller
L003 0003\9 Mechanisms Industrial Maintenance Trainer
[1] A study module including:
[2] Mechanisms Trainer and Accessories [3] Mechanisms Core Knowledge Learning
Material, in on-screen and paper-based forms
[4] Mechanisms Core Knowledge Instructor's Guide
[5] Mechanisms Troubleshooting Learning Material, in on-screen and paper-based forms
[6] Mechanisms Troubleshooting Instructor's Guide
[7] Student workbooks [8] Supporting text books [9] The study module should cover: gears,
spur gears, changing speed, stepped pulleys and belt drives, cams, fixed pulleys, moveable pulleys, levers, inclined planes, couplings /clutches, bearings
[10] Should allow: mixing mechanisms together, troubleshooting, condition monitoring, pulley and belt faults, chain faults, gear faults, shaft and coupling faults
L003 0003\10 PLC Simulation Software [1] Should incorporate the basic functions used in PLC Ladder Logic programming
[2] A visual editing environment for graphical programming
[3] The simulation software should incorporate at least 10 simulations
[4] The internal simulations can be controlled from a PLC
[5] Should permit control of external devices [6] Courseware with a general introduction to
PLCs, the various programming methods available and the fundamentals of ladder logic programming.
[7] Windows compatible L003 0003\11 Simulation And
Modelling Software [1] Minimum requirements: Windows 98, ME, NT, 2000 or XP; PII 450 MHz or higher; 64MB RAM; 16-bit; soundcard optional; web browser
[2] School Site Licence for school or Concurrent User Licence for 20 computers
[3] Features: systems and control, electronics, mechanisms, programming, PICs and microcontrollers, measuring and graphing
L003 0003\12 DC And Synchronous Stepper Motor
[1] A module to cover: DC permanent magnet motors, control and drive systems, synchronous AC motors, stepping motors,
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 23 of 154
Lot Item Code Item Description Target Specifications Yes No automatic speed control for DC and AC motors, automatic digital position control for stepping motors, automatic analogue position control for stepping motors and fault simulation
[2] Test and interconnection points [3] Rapid modifications to circuits using
jumpers
[4] Power supply L003 0003\14 Simulation Site Licence
For Physics [1] Simulation software to analyse the basic philosophy of a robot and its structure
[2] To analyse of the motion techniques, interface problems to the computer, analysis of the control software (motion algorithms of stepper motors, motion with self learning), industrial application of the robot
[3] To have at least 5 motion axes [4] Windows compatible L003 0003\15 Simulation Site Licence
For Technology [1] To simulate electrical circuits using over 100 components
[2] To simulate optical systems using lenses, mirrors, prisms and your own images
[3] To provide interactive demonstrations and experiments of simple harmonic motion and Hooke's law
[4] Interactive demonstrations and experiments of collisions, acceleration, velocity, kinetic energy
[5] For modelling and testing designs in electronics, programming, mechanisms and PICs
[6] Permits measuring and graphing [7] Windows compatible L003
0003\16 Simulation Site Licence For Control Programming Concepts
[1] Simulation which allows simple on-screen programs to be written using flowcharts
[2] Flow chart controls on-screen animated inputs and outputs
[3] Demonstrates abstract programming concepts, such as variables, loops, functions and conditional statements
[4] Windows compatible L003 0003\17 Simulation Work Station
Licence For Electropneumatics
[1] Simulation on electropneumatics
[2] Windows compatible L003 0003\18 Simulation Work Station
Licence For Electrohydraulics
[1] Simulation on electrohydraulics
L004 0004\1 Motor Mechanics Tool Kit
[1] Minimum 8 piece open end wrench set 6x7, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19 & 20x22mm
[2] Minimum 8 piece offset ring wrench set 6x7, 8x9, 10x11, 12x13, 14x15, 16x17,
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 24 of 154
Lot Item Code Item Description Target Specifications Yes No 18x19 & 20x22mm
[3] Adjustable wrench length approximately 200mm, capacity 24mm
[4] Minimum 3 piece plier set , 160mm combination, 160mm radio pliers, 160mm diagonal side cutters
[5] Minimum 4 piece circlip plier set [6] Tin snips 250mm long [7] Minimum 7- piece screwdriver set to
include: 3 plain slot size 38 x 6.0mm, 100 x 6.0 and 150 x 8.0mm, cross point No 1 and 2, PZ No. 1 & 2
[8] Minimum 7-piece hexagon key set, contents: 1.5, 2.0, 2.5, 3.0, 4.0, 5.0, and 6.0mm with ring and wallet
[9] Hacksaw frame, adjustable for 250 to 300mm blades
[10 10 compatible blades various TPI [10] Minimum 5 piece chisel and punch set
containing: flat cold chisel 20 x 150mm, 2 parallel pin punches 3 x 150 & 5 x 150mm, 1 taper pin punch 3 x 120mm and centre punch 4 x 120mm.
[11] Engineers ball pein hammer, weight 340g
[12] Engineers scriber [13] Steel rule 300mm / 12" [14] Metric feeler gauge set, 100mm long,
minimum 20 blades
[15] Minimum set of 12 files comprising flat, hand, half-round, round, square & 3-square second cut files with handles
[16] File brush [17] Slide caliper rule 150mm [18] Steel measuring tape 3m [19] Spring divider [20] Back square [21] Flat square [22] Plastic hammer [23] Mini hacksaw + 10 Blades [24] Triangular scraper [25] Cleaning towel [26] Dust brush [27] Rivet setters 3-4 mm [28] Rivet punch 3-4 mm [29] Soldering iron 60watt [30] Soldering iron support L004 0004\2 Carburettor & Fuel
Injection Tool Set [1] Comprehensive set packed in case to contain
[2] Bosch K mixture tool
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 25 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Bottom fitting tool [4] Nikki and Hitachi tool [5] Float needdle valve spanner [6] Aisan and Mikuni tool [7] Bosch mixture tool [8] Stromburg dual purpose tool [9] Tamper proof mixture tool [10] Weber tool L004 0004\3 Compression Test Set -
Petrol Engine [1] Scale - 0 to 290 psi / 0 to 20 bar
[2] 330mm of flexible hose fitted with side relief valve
[3] M14 / M18 adaptor 2 separate adaptors for 10 and 12mm
L004 0004\4 Diesel Engine Compression Tester
[1] Pressure relief valve for repetitive testing
[2] Suitable for car and light commercial vehicles with direct or indirect injection
[3] Dual scale fitted with protective cover [4] Supplied in fitted case. L004 0004\5 Automotive Diagnostics
Kit [1] For automotive engine diagnostics and fualt finding using suitable laptop / PC
[2] Kit to comprise: [3] PC based digital oscilloscope [4] Engine diagnostics sensor [5] 600A AC/DC current clamp [6] 60A DC current clamp [7] 20 : 1 attenuator [8] Multimeter probes [9] Clips and piercing probe [10] Test lead set x 2 [11] Secondary ignition pickup [12] 2 pin break out lead [13] Cigar lighter power lead [14] Automotive software CD [15] Quick start guide [16] Carry case L004 0004\6 Diesel Fuel Injector
Tester [1] For testing all types of automotive injectors
[2] Gauges 0-6000 psi / 0-400 bar with isolator valve
[3] Fuel pump type element, combined in a replacement cartridge
[4] Pump output: 1600 to 1800 mm per stroke
[5] Supplied with quick action pipe with nylon nipple enabling complete seal using only hand pressure
[6] Accommodates 14mm and 12mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 26 of 154
Lot Item Code Item Description Target Specifications Yes No threads
L004 0004\7 Automotive Electrical Simulator
[1] This training aid electrically equivalent to a standard motor car, to provide instruction in all aspects of automotive electrical systems
[2] For demonstration of the working functions of the various components
[3] Switchable fault conditions [4] Includes voltmeter, ammeter, electrical
tachometer and charge indicator on control panel
L004 0004\8 Electronic Fuel Injection Simulator
[1] An electronic fuel injection system mounted on a display board for use in instructional training and demonstrations
[2] Injectors mounted into a transparent tube so that their operation can be observed
[3] Electronic speed simulator operating over engine speed range of 500 to 5000rpm
[4] Built-in electronic ignition linked to engine speed
L004 0004\9.1 Brake Efficiency Tester [1] Self-contained portable brake tester [2] Test results stated in "G" units +/-0.02G [3] Measures peak, and average
deceleration, front and rear
[4] Measures Peak acceleration left / right [5] Vehicle pulls left / right indication and
value
[6] Calculates stopping distance and test speed
[7] To be supplied with data cable for downloading to PC
[8] Supplied with interpretation / printing software
L004 0004\9.2 Tool Set For Vehicle Electricians
[1] 8-piece open end spanners: 6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 17, 18 x 19, 20 x 22mm
[2] 8-piece screwdriver set: 3 x plain slot sizes - 6.0 x 38mm, 6.0 x 100mm, 8.0 x 150mm; 1 x plain slot with parallel tip size: 3.2 x 75mm; 2 x cross slot No. 1 & 2; 2 x PZ type No. 1 & 2
[3] Plain slot/PZ type angle screwdrivers: 5mm x No.1, 6mm x No.2
[4] 11-piece precision screwdriver set: 2 x plain slot - 2.4mm & 3.0mm; 2 x cross slot - No. 0 & 1; 2 x PZ type size - No. 0 & 1; 5 x TX-star sizes - T6, T7, T8, T9 & T10
[5] Set of 10 metric hexagon wrenches [6] 450g ball pein hammer [7] 110g cross pein hammer [8] Retractable knife. [9] Hacksaw frame + pack of 10 blades x
300mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 27 of 154
Lot Item Code Item Description Target Specifications Yes No [10] Junior hacksaw + 10 blades [11] 5-piece chisel and punch set [12] 12-piece 140mm needle file set; 6-piece
200mm engineers file set
[13] 3 metre tape measure [14] 3 piece set of soft grip pliers:
combination pliers - 180mm, long nose pliers - 160mm and diagonal side cutters - 160mm
[15] Soft grip wire stripping pliers - 160mm [16] 240mm water pump pliers [17] 5-way crimping & wire stripping kit [18] 200mm adjustable wrench [19] Soldering iron 40 W and solder sucker [20] Soldering iron stand and flux-cored
solder x 100g reel
[21] Insulating tape: black, red, yellow/green (8 rolls of each)
[22] Multimeter [23] Cantilever tool box with 4 cantilever
trays: approx. dimensions 500 x 200 x 200mm
L004 0004\12 2-Post Vehicle Lift [1] Capacity 2500kg gross weight [2] Electromechanical operation [3] Max. lift height approx 1800mm [4] Safety controls on raise and lower
buttons
[5] Fully adjustable support arms with rubber pads
[6] Single phase drive motor L004 0004\13 Transmission Jack [1] Capacity 500kg [2] 2-stage hydraulic cylinder [3] Lift - 1800mm approx. [4] Adjustable support cradle to
accommodate awkward shapes and sizes
[5] Safety chains for added security [6] Fully adjustable saddle with tilt & cross
controls
[7] Foot-operated release control L004 0004\14 Chain Hoist [1] Safe working load 2000kg [2] Standard lift 2.5 m [3] With mechanical load brake [4] Fitted with load hooks L004 0004\15 Mobile Floor Crane [1] Capacity at minimum jib length 1000kg [2] Max jib extension 1500mm approx. [3] Lift height 2700 mm approx. [4] Double acting hand pump [5] Mounted on wheels L004 0004\16 Universal Engine Stand [1] Head Swivels 360°
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 28 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Capacity - 900kg [3] Approx. dimensions: width - 800mm,
length - 1300mm, height - 1000mm
L004 0004\17 Trolley Jack [1] Capacity: 3 Tonnes [2] Lifting range: 150 - 500mm approx. [3] Overall dimensions: 660 x 350 x 160mm L004 0004\18 Axle Stands [1] All welded construction with pin and
chain load support
[2] Capacity: 5 tonne per pair [3] Min height 300mm approx. [4] Max height 500mm approx. L004 0004\19 Workshop Compressed
Air Supply [1] 1 x air compressor with 300 litre receiver
[2] 30 x air line quick couplings 1/2" BSP thread
[3] 20 x air line standard coupling adapter/tailpiece
[4] 40 x hose clips [5] 100m x galvanised steel air pipe 1/2" [6] 30 x galvanised steel elbows 1/2" [7] 10 x filter regulator lubricator [8] 40 x hose clips - jubilee pattern [9] 10 x air guns [10] 4 x combined filter regulator, dry air - for
spray guns
[11] 4 x air spray gun, 1 litre pot [12] 12 x 30m PVC reinforced air-line L004 0004\20 Air Compressor [1] Air Displacement: 175 l/m, min. [2] Free Air Delivered: 120 l/m, min. [3] Maximum Pressure: 8 bar [4] Receiver Capacity: 25 litres L004 0004\21 Air Impact Wrench Kit [1] 1/2" sq. drive [2] 10 chrome vanadium steel impact
sockets sizes - 9, 10, 11, 13, 14, 17, 19, 22, 24 and 27mm
[3] Chrome vanadium steel extension bar: 125mm
[4] 1/4" BSP nipple [5] Mini Oiler [6] Supplied in case L004 0004\22 Battery Charger [1] Vehicle battery starter / charger [2] 12 and 24 volt charge output: 28 A [3] 12 and 24 volt start output: 230 A [4] fuse protected for polarity and overload [5] Supplied with cables and 5 spare fuses L004 0004\23 Battery Hydrometer [1] Float calibrated from 1.100 to 1.300 [2] Fitted with flexible nozzle and
compressible bulb
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 29 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Approx. length: 100mm L004 0004\24 Battery Tester [1] Hand held battery tester for testing 12V
batteries
[2] Applies load across terminals and reads voltage performance
[3] Fitted with moving coil voltmeter L004 0004\25 Vacuum Brake Bleeder [1] One man operation using workshop air
supply
[2] Draws fluid from bleed nipple [3] Reservoir caps not required L004 0004\26 Hydraulic Hose Clamp [1] Single handed snap action [2] Length 200mm L004 0004\27 Pipe Flaring Tool Kit [1] For producing convex double lap flares
on automobile brake and clutch pipes
[2] Manually operated [3] Hardened and ground steel [4] For mounting in a bench vice [5] Formers mounted in revolving turret with
cam lever action
[6] Single and double flares sizes : 3/16" 4.75mm, 6mm, 8mm & 10mm
L004 0004\28 Caliper Wind Back Tool Kit
[1] To return brake piston into the caliper
[2] Universal set in case L004 0004\29 Brake Wrench Set [1] Set of 6 chrome vanadium spanners [2] To fit popular sizes of brake pipe and
nipples
L004 0004\30 Brake Fluid Tester [1] To check moisture content of brake fluid [2] Allows comparison with new fluid [3] Audible and visual test cycle L004 0004\31 Clutch Aligning Tool [1] Precision steel bushes [2] Suitable for use on most European and
Japanese cars and light commercial vehicles
L004 0004\32 Ball Joint Separator [1] Forged steel construction [2] Enables removal of worn ball joints up to
19mm diameter
[3] 19mm spanner or socket drive L004 0004\33 Universal Hub Puller [1] Chrome steel body with thrust bolt and
tommy bar
[2] Suitable for 4 and 5 stud hubs L004 0004\34 Coil Spring Compressor
Set [1] Forged hardened and tempered carbon steel claws
[2] Opening 200mm, min. [3] M16 x 1.5mm screw L004 0004\35 Bearing Puller And
Extracting Tool Set [1] Hydraulic pump
[2] 3 x puller legs [3] 6 x nuts and washers [4] 6 x link plates
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 30 of 154
Lot Item Code Item Description Target Specifications Yes No [5] 2/3 leg puller yoke [6] Hose adaptor [7] Min/max reach 0 to 150mm [8] Min/max spread 100 to 240 mm L004 0004\36 Side Level Grease Gun [1] Hand-lever grease gun [2] Capacity - 500cc [3] Delivery pressure - 10,000 psi or
equivalent
[4] 4-jaw coupler [5] Includes 5 x 400g grease cartridges L004 0004\37 Drain Pug Key Set [1] 11 x chrome vanadium steel keys [2] 1 x tommy bar [3] Suitable for sump plugs on engine,
gearbox and back axle
[4] Metric and imperial size L004 0004\38 Gravity Feed Oil Drainer GRAVITY FEED OIL DRAINER [1] Capacity - 75 Litres [2] Telescopic Steel Funne with filter Grid [3] Brass Drain Cock [4] "Full Drum" Device L004 0004\39 Torque Wrench [1] 3/8" square drive - range 5 to 22nm,
reversible ratchet head, display of torque values
[2] 3/8" square drive - range 15 to 50nm, reversible ratchet head, display of torque values
[3] 1/2" square drive - range 50 to 180nm, reversible ratchet head, display of torque values
[4] Supplied in moulded case with calibration certificate
L004 0004\40 Drive Socket Set [1] 21x 12 point sockets sizes - 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24, 26, 27, 28, 30 and 32mm
[2] 15x 12 point sockets sizes - 3/8" to 1 1/4" AF
[3] 10x 12 point deep sockets sizes - 10 to 24mm
[4] 6x 12 point deep sockets sizes - 7/16" to 3/4" af
[5] 3x spark plug sizes - 10mm, 12mm and 14mm
[6] Reversible ratchet [7] 3x extension bars - 75mm, 125mm and
250mm
[8] Sliding "t" bar [9] Flexible handle
{10] Offset handle
[10] Universal joint [11] Speed brace
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 31 of 154
Lot Item Code Item Description Target Specifications Yes No L004 0004\41 Spark Plug Kit [1] Insulated spark plug pliers [2] Miniature wire brush set - 3 pieces [3] Plug runner [4] Spark plug threads chaser 10 & 12mm -
14 & 18mm
[5] Universal joint magnetic spark plug socket 1/2" drive 10mm and 14mm with tee bar
L004 0004\42 Hex, Torx Socket Driver Bit Set
[1] Set manufactured from hardened chrome vanadium steel
[2] Includes 1/2" and 3/8" socket adaptors [3] Hex. bits 4, 5, 6, 7, 8, 10mm - 1 each 30
and 75mm long
[4] TORX multi-spline bits T20, T25, T30, T40, T45, T50, T55 - 1 each 30 and 75mm long
[5] TRX - STAR bits T60, T70 - 1 each 50 and 78mm
L004 0004\43 Valve Spring Compressor
[1] Capacity 55 - 95mm; 130mm throat
[2] Capacity 60 - 155mm; 160mm throat [3] Capacity 75 - 175mm; 150mm throat L004 0004\44 Valve Seat Cleaning Kit [1] Removes carbon deposits on cast iron
valve seats
[2] Cutters and pilots with 45 degree cone angle
[3] 4x chrome steel cutters & 7 precision pilots
[4] With screw - in holder and tee bar [5] Supplied in a metal case L004 0004\45 Valve Grinder Kit [1] With automatic lapping direction reversal [2] For clamping in a hand drill [3] Supplied with suction cups, 20, 25, 30
and 37mm diameter
L004 0004\46 Piston Ring Compressor [1] Capacity 45 to 75mm. depth 50mm [2] Capacity 60 to 100mm, depth 75mm [3] Capacity 75 to 140mm, depth 75mm [4] Capacity 70 to 150mm, depth 100mm L004 0004\47 Remover/Scraper Set [1] 2x multi-purpose scrapers - 210 and
275mm
[2] Scratch awl - 200mm [3] Cotter pin puller - 225mm [4] Radiator hose remover - 175mm L004 0004\48 Cylinder Leakage Tester [1] 3x glowplug adaptors - M10 x 1.25, M12
x 1.25, M14 x 1.25
[2] 2x dummy injectors - M24 [3] 1x stanadyne dummy injector [4] 2x glowplug adaptors - M10 x 1.25, M10
x 1.0
[5] Dummy injector - M20 x 1.5
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 32 of 154
Lot Item Code Item Description Target Specifications Yes No [6] Extension set - M14 [7] 3x spark plug adaptors M10, M12 & M18 [8] Clamp plate [9] Cylinder leak record pad [10] Male quick coupling adaptor - M18 L004 0004\49 Universal Cooling Sytem
Tester [1] For testing vehicle cooling systems under pressure
[2] Heavy duty radiator filler adaptor [3] Pump with pressure gauge [4] Hose and quick release coupling [5] Designed for most European and
Japanese vehicles
[6] Supplied in moulded case L004 0004\50 Digital Timing Light [1] Xenon timing light [2] 4-digit readout [3] 1.5 m coiled 12 volt power supply lead [4] Inductive coupler [5] Advance 0-60 degrees BTDC [6] 0 to 8000 rpm [7] Dwell accuracy 99% min. L004 0004\51 Digital Automotive
Analyser [1] DCV: 320mV, 3.2, 32, 320 and 600
[2] ACV: 3.2, 32, 320 and 600 [3] Resistance: 320, 3.2, 32K, 3.2M,
32MOhms
[4] Tachometer (x10rpm) 3, 4, 5, 6 and 8 Cylinder
[5] Dwell Angle 3, 4, 5, 6, and 8 Cylinder [6] Duty cycle 1 to 90% [7] Temperature Range: -4 to 140°C L004 0004\52 Injector Cleaning Kit [1] Kit of tools for cleaning fuel injector
nozzles, including: scraper, wire brush and 4x sets of pricker wires
L004 0004\53 Injector Stripping Jig [1] For use with injector cleaning kit L004 0004\54 Injector Extract Kit [1] Kit for the extraction of diesel injectors L004 0004\55 Diesel Exhaust
Smokemeter [1] For measurement of exhaust smoke
[2] Partial flow opacimeter for free acceleration or full load testing
[3] Integral 24-column dot matrix [4] Output: analogue: smoke value & engine
speed (for use with pen recorder)
L005 0005\1 Light And Temperature Control Module
[1] Light and temperature control module equipped with commonly used temperature and light sensors / transducers
[2] The connection points, light transducers and sensors shall be clearly laid out and identified on the front face of the module
[3] Module to include light source, drive
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 33 of 154
Lot Item Code Item Description Target Specifications Yes No circuit and three different types of transducers and amplification circuits
[4] Features included: light source and drive circuit, photo resistor measurement bridge, photodiode, phototransistor and ability to configure amplifier as threshold comparator
[5] Study topics to include: light intensity-to-voltage conversion, measurement of light intensity, proportional light control, on-off light control and the light-activated switch
[6] Module to include minimum four different types of commonly used temperature sensors (J-TC, NTC, PTC, bi-metallic switch)
[7] For study of open and closed loop temperature control
[8] Module to include: heating element and heat sink, J-type thermocouple, NTC, Pt 100 platinum resistor, bi-metallic thermic switch, reference-feedback summing node, adjustable gain amplifier and burst controller
[9] For study of characteristics and use of the 4 temperature transducers, linearizing techniques, open and closed loop temperature control, proportional and ON/OFF temperature controls and the duty cycle control technique
[10] To be supplied with interconnecting leads
L005 0005\2 Transducers Module [1] A set of experiment boards for studying transducers
[2] All components and functional blocks shown on module surface
[3] Trainer to include a PC interface module for complex remote control and simulated systemsmonitoring
[4] Modules shall include: strain gauge measurement, sound and vibration transducers, on / off sensors, air flow transducer, differential pressure transducer, rotational position encoders, linear variable differential transducer and level measurement
L005 0005\3 AD/DA Converter Module
[1] Input range: ranging between 0 to 8V and -8 to +8V
[2] Output range: ranging between 0 to 8 V and -8 to +8V
[3] Digital display of digital signals [4] Interface for PC [5] Analog signal display [6] Digital value configuration via switches [7] Variable frequency sine generator for A/D
conversion
[8] Fault simulation [9] Integrated power supply
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 34 of 154
Lot Item Code Item Description Target Specifications Yes No L005 0005\4 Process Simulator [1] To include functional blocks for study of
the simulated behaviour of various types of linear and non-linear processes and the different control techniques involved in each situation.
[2] The simulator module shall be divided into functional elements and identified on the front surface
[3] Features shall include: 2-input linear adder with complementary outputs, integrator, derivator and multiplier by a constant
[4] Also to include: 3-input linear adder and blocks to simulate common regulation impairments: offset generator and triangle wave drift simulator and blocks to simulate common non linearity of real systems: saturation, backlash and hysteresis
[5] Study topics shall include: open and closed-loop control systems, and also the gain, the effects of additive disturbances and the effect of multiplicative disturbances of negative-feedback closed-loop systems and also the bandwidth of closed-loop control systems, regulation error and first and second-order control systems
[6] Sockets for test and interconnection shall be provided
L005 0005\5 PID Process Control [1] The module shall be compatible with the Process Simulator above
[2] To study the behaviour of P, I, D control systems
[3] The module shall include a fault simulation system
[4] Features shall include: DC reference generator potentiometer, adjustable-frequency generator (triangle, square), 2-input summing amplifier, 3-term controller with separately adjustable parameters and an output adder for the 3-term controller
[5] Study topics shall include: applications, transfer functions, adjustment of PID controllers and fault simulation
[6] Sockets for test and interconnection shall be provided.
L005 0005\6 PLC Process Control [1] A module for theoretical analysis and the experimentation on: fuzzy logic, fuzzy sets, member function, inferential motors, fuzzying and defuzzying methods and fuzzy conntrollers
[2] To include PID applications (luminosity control, temperature control, presure control)
[3] Fuzzy applications (temperature control, pressure control)
L005 0005\7 DC And Syncronous Stepper Motor Module
[1] To enable the experimentation and investigation of the SXS control technique and typical characteristics of step-by-step
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 35 of 154
Lot Item Code Item Description Target Specifications Yes No motors and their electronic drive circuits
[2] A module for studying stepper motors [3] The electronic section shall include a
phase-signal generator and power drive stage. The motor must be operated manually in single steps or sequentially from an on-board clock generator.
[4] The module shall include a PC data link for full remote operation and software.
[5] Features shall include: small size step-by-step motor, variable-frequency clock generator, phase-signal generator and manual or sequential operation
[6] Study topics shall include: full and half step operation, control diagram development, driver logic development, remote operation under PC control and operation at various speeds
[7] A module for studying DC servo control techniques and investigations of position, speed and speed + position
[8] The trainer shall include: DC motor, tacho-generator, optical encoder, servo potentiometer and inertial and resistive motor loads
[9] To include power stage capable of operation in the PWM mode and reference generator, loop amplifier, PID controller and signal conditioners for the analog transducers
[10] The system shall include monitoring outputs to analyze the performance of the system under test and produce signals for recording through a data acquisition system.
[11] Study topics shall include: speed control and position control operation, stability and stabilization, regulation errors versus loop gain, effects of additive and multiplicative disturbances versus loop gain, the PI, PD, PID controller, P, I, D parameter settings and cutoff frequency of the servo system
L005 0005\8 Mini Robot For Stepper Motors
[1] A system to allow analysis of the basic philosophy and structure of a robot
[2] To permit analysis of the motion techniques (use of stepper motors), problems with the computer interface, control software (motion algorithms of stepper motors, motion with self learning)
[3] To describe industrial robot applications [4] To have at least 5 motion axes L005 0005\9 Multistandard Color
Television Trainer [1] The trainer shall consist of a TV receiver system of the latest design, constructed in sturdy portable case
[2] Clear synoptic diagram displaying the functional blocks and component identities
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 36 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Front-mounted electronic circuits for easy
inspection and simplified reference with the synoptic diagram.
[4] Electronic circuits with transparent safety cover
[5] 14" cathode-ray tube [6] System, PAL B,G SECAM B,G,K NTSC
from AV input socket
[7] Programme menory 49 + 1 AV position [8] Infrared remote control
(b) Trouble shooting and fault simulation
[9] The trainer shall be equipped with fault simulation system giving a minimum of 20 faults
[10] Faults shall be automatically reset when the student precisely locates the component or group of components concerned
[11] All attempts performed by the student shall be stored in the system memory and can be retrieved, printed and checked by the instructor for evaluation
L005 0005\10 Compact Disk Trainer [1] This trainer shall consist of a commercial apparatus, transformed for didactic use
[2] Mounted to allow a clear view of the mechanics
[3] A circuit synoptic board which indicates the system functional block diagram shall incorporate test points for student measurements
[4] The system shall be equipped with a fault simulator, operating a set of concealed switches
[5] Technical Specification: multifunction digital display, DAC 1 bit, over- sampling x8, pre-programmed sound equalization
[6] Facilities: remote control, forward, reverse, skip, search, repeat and random play
[7] The trainer shall be supplied complete with cables and accessory kit
L005 0005\11 DVD Trainer [1] A commercial DVD apparatus, transformed for didactic use
[2] Mounted in a transparent enclosure allowing a clear view of the mechanics
[3] A circuit synoptic board which indicates the system functional block diagram shall incorporate test points for student measurements
[4] The system shall be equipped with a fault simulator operated by a set of concealed switches
[5] Ability to operate both DVD and CD disks [6] PAL/NTSC standard without
transcodification
[7] Digital and analogue signal outputs in all common standard formats
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 37 of 154
Lot Item Code Item Description Target Specifications Yes No [8] Standard EURO AV socket [9] SVHS output [10] Remote controller L005 0005\12 Learning Module For
Digital Logic [1] A series of modules for studying digital logic circuits
[2] Components used shall be representative of the types commonly in use: CMOS 40XX and 45XX families
[3] The trainer shall be supplied with a power supply delivering the voltages required to perform the experiments
[4] The following subjects and topcs shall be covered
[5] Transistor switch: the OFF state, the ON state, transition between states, speed-up techniques, transistor switch with capacitive load and bilateral switch with capacitive load
[6] Transistor multivibrators: bistable circuit, bistable with speed-up capacitors, toggle-mode operation of the bistable circuit, non-saturated bistable, with emitter coupling and astable circuit
[7] Schmitt trigger: open-loop dc gain of the amplifier, operation with positive feedback, hysteresis; applications: tank level control system, waveform shaper
[8] Transistor signal generators: blocking oscillator, triangalar wave generator
[9] Basic logic gates: logic addition (logic or), logic product (logic and), inverted logic addition (logic nor), inverted logic product (logic nand)
[10] Digital gates: nand operation, and operation, or operation, nor operation, rs bistable (flip-flop), astable circuit
[11] And/or/not gates: and operation, or operation, not operation
[12] Nand/nor gates: nand operation, nor operation
[13] Special logic functions: addition of binary numbers, half addition, full addition, subtraction of binary numbers
[14] Binary decimal converters [15] Quad d-type flip-flop module: frequency
divider, parallel register, binary up-counter, binary down-counter, presettable divide-by-n counter, shift register
[16] CMOS applications: frequency-controlled CMOS oscillator, CMOS Schmitt threshold circuit, generation of logic levels from slow-envolving signals, timer-delay generator, timing generator
[17] Output devices: bcd to /-segment converter, 8 logic state indicators, relay driver
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 38 of 154
Lot Item Code Item Description Target Specifications Yes No [18] Double IC holder and IC set: to allow
the study of aditional chips, a kit of ICs from the 40xx and 45xx family shall be included.
L005 0005\13 Digital Trainer [1] Based on large solderless breadboard [2] To include logic probe [3] Interconnection via solid 0.3 - 0.8mm wire [4] To include ajustable clock generator,
mains adapter, on-board 5v 1A regulator, 8 slide switches, 2 pushbutton switches
[5] Also includes two BNC connectors for connection to test equipment and two 4mm jacks
[6] Supplied with pack of integrated circuits (555, 7400, 7402, 7408, 7411, 741, 7474, 74138, 74112, 74147,74161, 74137, 74163, 74193, 74283) x 50 of each and resistors (100, 560, 1k, 2k2, 3k9, 10k, 100k, 1M)
L005 0005\14 Learning Module For Microprocessors 8bit
[1] For study of 8 bit microprocessor system programming and analysis of hardware structure
[2] To include: memory devices, data and address bus, instructions and addressing modes and interfacing of RAM and EPROM
[3] Provided with keyboard and display control, parallel and serial interface, A/D and D/A conversion and troubleshooting facility
[4] Toinclude: 8 bit microprocessor, at least 4 kbyte system EPROM, 4 kbyte user EPROM and 4 kbyte RAM
[5] With keyboard, display, PIO/ SIO interface, expansion bus interface, analogue input/output 8 A/D D/A converter
[6] To include at least 8 insertable fault conditions, at least 6 logic probes, monitor program in EPROM and power source
L005 0005\15 Electronic Lab Simulation Software
[1] Software to simulate processes in items 1 to 4
L005 0005\17 Virtual Scope, Type 1 [1] At least 8 bit resolution [2] 2x channels + external trigger [3] Voltage ranges +/- 50mV to 20V [4] Sampling rate at least 20Ms [5]Timebases from 100ns/div to 50 s/div [6] Spectrum 10MHz [7] Buffer size at least 8k [8] With output connection to PC parallel or
USB port
[9] Software included L005 0005\18 Virtual Scope, Type 2 [1] At least 8 bit resolution [2] 2x channels + external trigger [3] Voltage ranges +/- 50mV to 20V [4] Sampling rate at least 100Ms [5]Timebases from 100ns/div to 50 s/div
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 39 of 154
Lot Item Code Item Description Target Specifications Yes No [6] Spectrum 50MHz [7] Buffer size at least 8k [8] With output connection to PC parallel or
USB port
[9] Software included L005 0005\19 Aquisition Board [1] Sampling rate 10 to 15.000
samples/second or better
[2] Digital output 1 TTL minimum [3] Output connector to PC parallel or USB
port
[4] Includes software and sensors for sound, voltage, resistance, temperature, ligtht, pH and humidity
L005 0005\20 Digital Multimeter With Bargraph
[1] Dual display: digital and analogue bargraph
[2] Measuring ranges: 400mV to 600V DC/AC; 40 mA to 10A DC/AC; 400ohm to 40Mohm; 4nF to 40uF and 100Hz to 200kHz
[3] With conductivity/diode tester [4] Accuracy for AC voltage ranges: +/- 1
digit; accuracy for AC current ranges: +/- 2 digit
[5] With overload protection and recognition of changes in measurement value
L005 0005\21 Digital Multimeter [1] Large digit LCD display [2] 1000Vd.c. & 750Va.c. measurement [3] 400mA & 10A fused current ranges [4] Resistance, audible continuity & diode
test
[5] Frequency & rpm counter (max 200KHz) [6] Frequency display (Hz) [7] Display hold [8] 30-minute auto power off L005 0005\22 AC Power Supply [1] Primary: 230 V AC [2] Secondary: 12 V AC, 20 VA [3] Connection: female 4mm L005 0005\23 DC Power Supply [1] DC power supply: voltage continuously
adjustable from 0 to 30 V
[2] Short-circuit protection [3] Adjustable current 0-3 A min. [4] Ripple voltage 1 m Vrms max. or better. [5] Load regulation 3% approx. [6] Voltage meter, current meter. [7] Test lead, 1 set. L005 0005\24 Waveform Generator [1] For generating sine, triangular, square
wave or additional waveforms
[2] With DC offset [3] Frequency range: 10 Hz-10 MHz in 4
ranges or more
[4] Output level: 0 dB to -40 dB
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 40 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Output impedance at least 600 Ohm [6] Output sine wave: 10 Hz-10 MHz or
wider
[7] Output square wave: 10 Hz-100 KHz or wider
[8] Test lead 1 set. L005 0005\25 Digital Storage
Oscilloscope [1] Bandwidth: 0 to 50 MHZ or better
[2] Input impedance: 1 Mohm or better, 18 pF
[3] Screen: 8 x 10 cm with internal graticule [4] Time base: 0.5 s/cm...10 ns/cm, with X-
expansion x10 to 10 ns/cm
[5] Trigger source: CH1, Ch2, CH1 and Ch2 alternate, line and external
[6] Storage modes: refresh, roll, single, XY [7] Envelope, average, random sampling [8] 8 bit memory per channel [9] Sample rate: 100MSa/s or better [10] To include 100MHz probe and cable:
switchable, with spring-loaded hook tip; trimmer key, BNC adapter, probe tip, insulating covering, ground lead and 4-mm plug
L005 0005\26 Oscilloscope [1] Dual trace, 20MHz bandwidth [2] 2x screened connector leads [3] 1mV/div sensitivity [4] CH1 Output [5] ALT triggering function L005 0005\27 Frequency Counter [1] To measure frequency, period, pulse
duration and ratio measurement, and event counting
[2] Input A input: switchable between TTL and analog signal; frequency range: 1 Hz to 10 MHz
[3] Input B input: frequency range: 0 to 2 MHz, TTL level
[4] Digital display: 8-digit, 10 mm high; [5] Gate times: 10 s, 1 s, 0.1 s, 0.01 s L005 0005\29.
1 Experiment Module (Basic Electricity)
[1] Basic electricity experimentation on: measurements and symbols, Ohm's Law, series and parallel circuits, voltage dividers, attenuators, Kirchoff's laws, superimposition theorem, Thevenin's and Norton's theorem, DC power and power transfer
[2] Provided with means of investigating capacitance and capacitors, inductance and inductors
[3] Allows study of alternating signals: waveform, mean value, root mean square, value, period and frequency, AC resistive, inductive and capacity circuits, active and
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 41 of 154
Lot Item Code Item Description Target Specifications Yes No reactive power and transformers
[4] Pack of components (various types of connectors, cables, components mounted on support with metal terminals, electronic components)
L005 0005\29.2
Experiment Module (Electronic Circuits & Devices)
[1] Experimentation of electronic circuits and devices, including: PN junction, diode, rectifiers, smoothing and filtering circuits, clipping circuits, voltage doublers, clamping circuits, zener and varicap diodes, optoelectronic components, thermistors, NPN and PNP transistors, transistor connections, bias stabilisation, small signal parameters,
[2] To allow study of: dual load amplifier, multi-stage amplifier, differential amplifier, Darlington, cascade, boootstrap circuit, Class A, B, C amplifiers, oscillators, Schmidt trigger and multi-junction components
[3] Pack of components (various types of connectors, cables, components mounted on support with metal terminals, electronic components)
L005 0005\29.3
Experiment Module (Linear Micro-electronics)
[1] Investigations of operational amplifiers: typical parameters, applications (inverting and noninverting, summing, substractor, integrator, differentiator, comparator
[2] Allows study of: monostable and astable multivibrator, voltage-frequency converter, form generator, active filters, voltage regulators and audio amplifier
[3] Pack of components (various types of connectors, cables, components mounted on support with metal terminals, electronic components)
L005 0005\30 Development Module For Linear And Digital Electronic Circuits
[1] To include: power supply, function generator, TTL generator, hexadecimal keyboard, analogue inputs, display, logic indicators and breadboard
[2] The module will permit construction and will display the performance of: rectifiers, regulated power supply with discrete components and integrated circuits, amplifiers (differential, wide-band, selective, in class C), oscillators Meissner, Hartley and Colpitts, astable, monostable, and bistable multivibrator and Schmidt trigger, voltage regulators with UJT, SCR, DIAC, TRIAC
[3] To allow study of circuits with operational amplifiers, multivibrator, oscillator, active filter, or, and, not, nand, not ports with discrete components, networks with flip-flop RS, D, JK, latch, 4-bit shift registers, binary and decade counters and mux/demux circuit
[4] Pack of components (various types of connectors, cables, components mounted
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 42 of 154
Lot Item Code Item Description Target Specifications Yes No on support with metal terminals, electronic components)
L005 0005\32 Operational Amplifiers [1] This module enables experiments into: characteristics and parameters, offset voltage measurements, slew-rate measurement and open loop gain measurement
[2] Allows investigation into integrated operational amplifier applications: inverting amplifier, non-inverting amplifier, summing amplifier, subtractor amplifier, integrator amplifier, differentiator amplifier, comparator amplifier, logarithmic amplifier, monostable mutivibrator, Schmidt trigger, sine oscillator, waveform generator and filters
[3] Supplied with terminals for connections and measurements and at least two OA for performance evaluation
[4] All passive and active components necessary for circuit construction
L005 0005\33 Analogue Signal Processing
[1] To enable theoretical analysis and experimentation into: sum and difference of analogue signals, attenuation of an analogue signal, exponent/ logarithmic functions, multiplication, division, raising to a power, square root, integration, shunt, peak detector, AGC, AM modulation and demodulation, VCO and PLL
[2] To include terminal for connection and measurements and attenuator 0 to 15dB in steps of 1dB
[3]Supplied with signal generator, with variable frequency and fixed frequency signal generator
[4] PLL with variable frequency gain and 2 multiplier blocks
L005 0005\34 Module For Digital Electronics
[1] The module enables analysis of and experimentation into: AND, OR, NOR, NAND, XOR logic ports with two inputs, inverter, TTL and CMOS logic families, 3-state buffer, flip-flop, latch, BCD and shift registers
[2] Includes: 4-bit comparators, 4-bit complete adder, multiplexer and demultiplexer, monostable, 9-bit parity generator, BCD-decimal decoder, BCT/ 7 segment decoder/driver and 7 segment display, decimal-BCD coder and BCD selector
[3] To feature protection against wrong voltages and switches and displays to set and view the required logic state
L005 0005\35 Logic Families And Interfaces
[1] To investigate parameters of logic families: logic levels, switching speed, immunity to noise, power dissipation, fan in, fan out
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 43 of 154
Lot Item Code Item Description Target Specifications Yes No [2] TTL, CMOS, HCT, ECL logic family [3] Interfacing between different logic
families
[4] Analysis of the behaviour with resistive and capacitive loads
L005 0005\36 Personal Computer - Maintenance And Troubleshooter
[1] personal computer IBM compatible PC at least P4 at 2500 MHz at least 256 MB DDR SVGA with at least 128MB RAM at least 40 GB Hard disk Minimum 8x DVD/ 48x CD Player mouse, keyboard serial, parallel and USB interface win XP operating system with licence
[2] detection card for POST and solution codes plug in PCI card autonomous CPU integrated into a card POST address selection test sequential indicator switch for code/reset display 3 digit display POST codes and solution codes 3 led indicator for logic probe logic probe
[3] fault simulation unit membrane switch keyboard lcd display insertion of at least 12 faults (cut off or shortcircuit) use of the unit in TEacher mode in the first fault programming phase and Student mode in the next phase for research and detection of the same faults test points of the main signals of the mother board
[4] power supply [5] diagnostic software
system test:configuration and ratio advanced diagnostic test processor mother plate memory FDD and HDD CDROM, DVDROM, ZIP, SCSI devices serial and parallel ports modem, printers mouse and joystick audio video BURN-IN controls
L005 0007\1 Soldering Workstations [1] Low voltage soldering iron, at least 40W
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 44 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Selection of 2 interchangeable soldering
iron tips (fine point and wedge tip)
[3] Soldering iron power supply with mains-on lamp and externally accessible fuse
[4] Soldering iron stand and cleaning sponge L005 0007\2 Electronic Tool Kit [1] Wire stripper approximate length 130mm,
diagonal wire cutter, approximately 140 mm semi-flush 10mm cut
[2] Long nose pliers, approximately 150 mm, half-round tapered serrated jaws
[3] Pozidriv screwdriver, approximate blade length 75mm
[4] Flat blade screwdriver, approximate blade length 75mm
[5] Steel rule approximately 150mm long [6] Straight, fine-point tweezers,
approximately 115mm with serrated jaws
L005 0007\3 Desoldering Pump [1] Manual suction pump [2] Approximately 20 cm in length [3] Rigid connection nozzle L005 0007\4 Stripboard Track Cutter [1] For breaking tracks in PCB, stripboard
etc.
[2] Steel cutting tool [3] Plastic or wooden handle L005 0007\5 Simple Eye Glass [1] Approximately nine times magnification [2] Plastic lens with a focal length of
approximately 3cm
[3] Fixed in a plastic mounting L005 0007\6 Boxed Crimping Kit [1] To include 1x insulated crimp tool, with
crimp connectors red sleeve: 25 each of 2 B.A., 4 B.A. eyelets, 4 B.A. spades, flat pins, 0.25" receptacles and blue sleeve: 25 each of 2 B.A. eyelets, 4 B.A. spades and butts. Yellow sleeve: 15 each of 0 B.A. and 2 B.A. eyelets
[2] Supplied in plastic case L005 0007\7 Soldering Station And
Stripping, Wrapping & Unwrapping Tools
[1] Soldering and desoldering station with temperature display: 150-400°C
[2] Low voltage soldering iron [3] Low voltage desoldering iron with
desoldering tip
[4] Electric foot switch [5] Holder for soldering iron [6] Tip holder [7] Holder [8] Desoldering tip support [9] Cleaning brush [10] Vacuum meter [11] 1x tool for cable, wire,
strip/wrap/unwrap, regular wrap, 30 awg
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 45 of 154
Lot Item Code Item Description Target Specifications Yes No [12] 1x tool for wirewrapping,
strip/wrap/unwrap, modified wrap, 26 awg
L005 0007\8 Guillotine [1] Bench mounted PCB shears for cutting 1.6mm epoxy, bakelite and aluminium
[2] Reversible steel blade [3] Automatic board clamp [4] Supplied with rear stopper L005 0007\9 Hacksaw Junior [1] Square bar steel frame, with moulded
plastic handle, enclosed for finger protection
[2] Quick lever-action blade locking and change feature.
[3] Supplied with two spare 150mm × 32 tpi blades.
L005 0007\10 Engineer’s Vice [1] Bench mounting with 100mm jaw widths, for general purpose gripping applications
[2] Body and sliding jaw in cast iron [3] Jaw width : approximately 5cm [4] Jaw opening: approxately 2cm [5] Jaw depth: approximately 7cm [ L005 0007\11 File Set [1] Set of 4x engineers pattern second cut
files
[2] To include hand, half-round, flat and round
[3] With handles L005 0007\12 Needle File Set [1] Set of 12 needle files, 28 teeth/cm [2] To include hand, flat, round, half-round,
square, 3-square, crossing, joint, knife, oval, marking and barrette type
[3] Overall length: approximately 160mm [4] supplied complete in wallet L005 0007\13 BNC Spanner Set [1] A set of 2 zinc-plated hardened steel
spanners
[2] For tightening cable clamps on BNC connectors: AF sizes 1/2", 7/16", and 9/16"
L005 0007\14 Adjustable Spanner, Small
[1] Approx 150mm long
[2] Precision, hardened steel [3] Parallel jaws L005 0007\15 Adjustable Spanner,
Medium [1] Approx 200mm long
[2] Precision, hardened steel [3] Parallel jaws L005 0007\16 Drill/ Screwdriving Kit [1] To include 10x Ti-N coated HSS twist
drills
[2] To include 5x tungsten carbide tipped masonry drills
[3] To include 5x HSS wood drill bits and 1x countersinking bit
[4] To include 3x pozidriv bits, 3x philips bits, 2x slotted bits and 3x torx bits
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 46 of 154
Lot Item Code Item Description Target Specifications Yes No [5] To include 4x hexagon bits and 4x hex
sockets plus socket adaptor
[6] To include magnetic universal bit holder [7] To include reversible ratchet screwdriver
and 3m measuring tape
L005 0007\17 Heavy Duty Drill [1] 17-position adjustable torque control [2] Keyless chuck capacity: 1.5 to 10mm [3] To include 2x batteries, 1x charger and
carry case
[4] Torque: 18Nm min. L005 0007\18 Miniature Screwdriver
Set [1] Set of 12 screwdrivers
[2] To include: 5x slotted drivers: 1x35, 1.2x35, 1.5x35, 2x35 and 2.5x35; 2x Phillips drivers: No. 00 and No. 0; 2x Torx drivers: T6 and T7 and 3x Hexagon drivers: 0·9, 1·3 and 1·5mm
L005 0007\19 PCB Manufacturing Facility
[1] 4-tube, 15W UV exposure unit with 0 to 500 sec. timer
[2] Bubble etch tank with integral spray, water fill connections and front-mounted temperature controls
[3] 5 kg ferric etchant powder [4] 1kg photoresist developer powder [5] 4x seno applicators [6] Scrub block [7] Pack of 100 sheets of laser print film [8] 10x packs ofg assorted etch resist
transfers
[9] 10 latex gloves L005 0007\20 Eye Wash Station [1] 300ml of sterile saline water [2] In eyewash bottle L005 0007\21 Plastic Protective Apron [1] For protection against spills from PCB
manufacturing facility
[2] Approximately 100cm x 100cm L005 0007\22 Safety Glasses [1] Clear polythene [2] Universal bridge nose [3] Fixed side shields L005 0007\23 PCB Drill [1] Portable power tool [2] For use with DC supply: 6 to 18V [3] No-load speed approx 14,000 rpm [4] 4x collets to accept shank diameters from
0.6 to 3mm dia.
[5] To include tommy bar [6] Stall torque approximately 500 g.cm L005 0007\24 General Purpose Drill Bit
Set [1] For use with PCB drill
[2] High speed steel [3] Sizes to include: 0.9mm, 1.5mm, 2mm
and 2.5mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 47 of 154
Lot Item Code Item Description Target Specifications Yes No L005 0007\25 ESD Protected Area
Poster [1] To warn against electrostatic discharge hazard
[2] Glossy paper poster [3] Approx. 15 x 30cm [4] Standard ESD black warning symbols L005 0007\26 ESD Portable
Workstation [1] Rubber studded mat
[2] Wrist band [3] Shoe strap [4] Earthing lead with crocodile clip L005 0007\27 SMD Rework Station [1] To include power source, desoldering
iron, soldering iron, thermal pick handpiece, thermal tweezers, handpiece stands, tip maintenance station and accessory kit
[2] 3-channel rework station with self contained vacuum pump for hot air or desoldering
[3] Temperature range up to 475°C minimum displayed digitally
[4] Temperature offset retained in memory [5] Allows removal and placement of many
SMT components including PLCCs, SOICs etc.
L005 0008\1 Analogue Communications
[1] For studies and experiments on the basic properties of AM, FM, PM, single and double sideband operation and their circuits
[2] Allows investigation into the efficiency, linearity, modulation index and deviation rate of modulators and asynchronous and synchronous detection
[3] Demonstrates principles of IF amplifiers, gain, bandwidth, stability, AGC, detectors, discriminators and PLL demodulators
[4] Modular format with each circuit identified by silk screen printing
[5] On-board carrier frequency generator, adjustable in level and frequency
[6] Audio-frequency generator, to provide a modulating signal
[7] AM modulator, configurable to produce AM-DSB with carrier or with suppressed-carrier (AM-DSBSC)
[8] SSB filter, to produce an SSB wave from the AM-DSBSC
[9] PLL phase modulator, also usable as an FM demodulator
[10] IF amplifier with AGC generator and envelope AM detector
[11] SSB demodulator and PM detector [12] FM ratio discriminator [13] Audio-frequency output amplifier [14] On-board transmission media simulator,
with adjustable attenuator and noise
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 48 of 154
Lot Item Code Item Description Target Specifications Yes No generator
[15] To be supplied with set of connecting leads and power supply
L005 0008\2 FM Modulator/ Demodulator
[1] To familiarise students with the principles of PLL systems and its main applications
[2] To consist of a single large-size board with circuits clearly illustrated
[3] Voltage controlled oscillator, reference oscillator, frequency divider, phase comparator, loop filter
[4] Modules and circuit blocks to demonstrate the frequency shift keying
[5] Keying modulation/demodulation process, FM demodulation and frequency synthesis.
[6] To be supplied with set of connecting leads and power supply
L005 0008\3 AM Transmitter [1] For the study of structure and operation of AM receivers, analysis of AM waveform and sidebands, modulation index, modulation linearity and power
[2] Trainer to consist of complete transmitter capable of amplitude modulation with carrier and suppressed carrier double-sideband modulation
[3] To consist of a single board with circuits clearly illustrated
[4] The transmitter shall operate in the frequency range 550 to 1600kHz and be compatible with AM receiver
[5] Built-in tone generator to be used as a modulating signal reference
[6] Balanced modulator, AM/DSB [7] Output power limited to approx. 100mW [8] Built-in resistive dummy load to be
connected in place of antenna to prevent radiation
[9] Fault-simulating system for at least 8 different fault situations introduced by concealed switches
[10] To be supplied with set of connecting leads and power supply
L005 0008\4 AM Receiver [1] To allow study of the receiver's front-end, multi-stage selective amplifier (IF amplifier), audio amplifier, alignment and calibration procedures
[2] Allows measurements on all stages and on the whole system and study of troubleshooting techniques
[3] Shall consist of an AM receiver of modern design, operating in the 550 to 1600kHz band
[4] To be compatible with AM Transmitter [5] To consist of a single board with circuits
clearly illustrated
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 49 of 154
Lot Item Code Item Description Target Specifications Yes No [6] Provided with a switch-activated fault
simulating system for a minimum of 8 different fault situations
[7] Receiver front end with antenna [8] Combined RF amplifier, local oscillator
and mixer
[9] IF amplifier with automatic gain control and AM detector
[10] Audio amplifier and loudspeaker [11] Set of interconnecting cables and power
supply
L005 0008\5 Frequency Division Multiplexing
[1] A training module for theoretical study with exercices of frequency division multiplexing used in the simultaneous communication of telephone channels
[2] A complete frequency-division multiplex (FDM) system showing how two voice-frequency signals can be combined in the same transmission and be separated in the receiver
[3] To include carrier generators, test tone oscillators etc.
[4] To consist of a single board with circuits clearly illustrated
[5] Two signal amplifiers used to adapt impedance and level
[6] Two AM modulators for frequency-band translation of the two test signals
[7] One adder/transmission amplifier and one receiving amplifier
[8] Two channel filters with AM demodulators
[9] Two channel amplifiers and two test tone generators
[10] Two carrier generators, derived from an unique precise source
[11] Set of internonnecting cables and power supply
L005 0008\7 Pulse Modulation [1] To consist of modules necessary to build and study pulse modulation transmission systems of various types
[2] Modulation mode topics to include: pulse-amplitude, pulse-width, pulse-position and time-division multiplex transmission
[3] To consist of a singleboard with circuits clearly illustrated
[4] Sinewave test signal generator, as signal source
[5] TX timing generator [6] Analog multiplexer [7] PAM, PWM, PPM coders [8] Rx timing generator [9] Rx input amplifiers and decoders [10] Demultiplexers
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 50 of 154
Lot Item Code Item Description Target Specifications Yes No [11] Output amplifiers and filters [12] Set of cables L005 0008\8 4-Channel PCM
Multiplex [1] Module to study the principles of digital coding and pulse modulation techniques
[2] Consisting of a single board with circuits clearly illustrated
[3] Input amplifiers for 4 audio channels (0.3 to 3kHz bandpass)
[4] Sampler and A/D converter stage [5] Time-division multiplexer [6] PCM encoder and transmitter [7] Receiver, demultiplexer and PCM
decoder
[8] D/A converter stage [9] Output filters and amplifiers [10] Test facilities including sinewave test
tone generator with independent TX and RX timing generators
[11] Supplied complete with cables L005 0008\9 Fixed Telephone Trainer [1] To represent a fully functional digital
telephone exchange, with 6 extension lines minimum and facilities for investigation of digital switching techniques
[2] Digital, time-division switching network of the time-space-time configuration
[3] Each switching stage provided with memories whose contents can be displayed by indicators and monitored by a PC
[4] Two multiplexer/demultiplexer stages, each one to processing the signals of the 4 digital sources/destinations
[5] Channel banks to provide A/D and D/A conversion
[6] Line signalling interface, to process the signals to/from the phone lines according to the standards in use (ring, seizure, pulse and tone dialling, etc.)
[7] Dual-tone, multi-frequency receiver with pulse-dialling mode asalternative
[8] Exchange operating at standard rate (8k samples/sec) or in STEP mode
[9] Serial interface for use with PC for off-line monitoring of the exchange operation
[10] The trainer shall be complete with 6 phone sets with both pulse and tone dialing capability, cables, accessories kit, software monitor program and manual.
[11] Suitable for mains supply operation L005 0008\10 Telefax Trainer [1] The unit shall consist of an industry-
standard machines in current commercial use, of well known make, modified for didactic use
[2] To allow the operation of the system to be analyzed and studied using test points on
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 51 of 154
Lot Item Code Item Description Target Specifications Yes No a mimic diagram, on each section of equipment
[3] ITU-T (CCITT) G3 mode compatibility [4] Half-duplex transceiver [5] Modified Huffman compression scheme [6] Manual/automatic operation [7] 8-tone grey-scale L005 0008\11 Telephone Switching
And Transmission [1] A trainer suitable for teaching the structure and organization of modern PBXs and to familiarize the student with its systems and equipment
[2] The unit shall include 6x internal subscriber terminals, two trunk line interfaces and an operator's position
[3] These shall be routed by a solid-state analog exchange matrix
[4] The trainer shall also include on-board tone and ring generators
[5] Microprocessor system control [6] To include a fault simulating system,
programmable, operating a set of minimum of 8 concealed switches
[7] To have the capability of linking to a PC for monitoring and studying its operation and for troubleshooting
[8] Minimum of 6 telephones sets [9] Supplied with system monitoring software L005 0008\12 Mobile Telephone
Trainer [1] For familiarisation of the structure, system orgainisation and physical aspects of mobile phones
[2] Topics to include: use of radio channels for the conversation and control signals, types of modulation used, functional characteristics, measurement on various cellular telephone sets and troubleshooting
[3] Consisting of a commercial GSM mobile phone, disembled, mounted on a training panel
[4] Internal structure to be exposed with some components removed and mounted on training panel
[5] Panel to be printed with system block diagram with test access points
[6] System to be provided with switch-activated fault simulator
[7] Capable of operating in standard GSM 900 and GSM 1800 bands
[8] Number of channels 1320 - GSM 900 and 885 - GSM 1800
L005 0008\13 Optical Fibres [1] Module to cover: fibre characteristics, optical sources and detectors, LED polarisation, responsivity of a photodetector, optical fiber attenuation, analogue and digital communication, data coding/decoding
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 52 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Signal sources: TTL generators, data and
audio, microphone, video generator
[3] Data coders/decoders (NRZ, Manchester, biphase)
[4] 8x channel TDM data mux/demux [5] Optical sources and detectors [6] 5 different types of optical cables [7] ST - ST adapter [8] Reception circuits [9] Video/audio mux/demux [10] Fault simulator [11] Power supply L005 0008\14 Personal Computer -
Maintenance And Troubleshooting
[1] To consist of a Pentium class PC, adapted for use in practical laboratory courses for computer maintenance
[2] The system electronics shall be accessible for experimentation and includes transparent covers to protect the equipment
[3] To include a fault simulation system with minimum 12 different fault situations
[4] The programmable faults shall cover all subassemblies/sections of the system and be programmed by concealed operating keys
[5] Additional faults may be generated by inserting a faulty component into the main board.
[6] Computer specification to include: VGA colour screen, 256 Mbytes RAM, floppy disk drive, CD-ROM drive, hard disk, keyboard, mouse, multiple USB ports, parallel and serial port
L005 0008\15 Telecommunications Simulation Software
[1] To be used with any PC having following characteristics: IBM compatible, 128 MB RAM, SVGA card, CD reader, windows 98se and higher operating systems
[2] Fourier analysis and synthesis [3] Analog modulations/demodulations (AM,
FM, DSB and SSB)
[4] Signal processing (filters, power amplifiers, mixers)
[5] PLL [6] Digital modulations (PAM and TDM,
PCM)
[7] Communications system (FDM, transmitter/receiver for optical fibres
L005 0008\16 LAN WAN Simulation Sofware
[1] To be used with any PC having following characteristics: IBM compatible, 128 MB RAM, SVGA card, CD reader, windows 98se and higher operating systems
[2] Elements of LAN communication infrastructure, users and servers, transmission means
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 53 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Proprietary wiring and structured wiring [4] Architecture: star, ring, bus, tree [5] Network active components [6] Signal coding [7] ISO/OSI model and LAN/IEEE model [8] IEEE802.3 / Ethernet [9] IEEE802.2 u - Fast ethernet [10] Token ring [11] Protocols of 3,4 level [12] LAN configuration [13] Mixed configurations [14] Network control and management [15] Network operative systems [16] Internet/intranet L005 0008\17 Telematics Simulation
Software [1] To be used with any PC having following characteristics: IBM compatible, 128 MB RAM, SVGA card, CD reader, windows 98se and higher operating systems
[2] For instruction on data transmission, data codes and format, modulation techniques and international recommendations
[3] For instruction on equipment and devices, including serial interfaces, measurement instruments and measurements, modems
[4] To cover protocols: osi model, communication, BSC, HDLC, SDLC and communication software packets
L005 0008\18 Virtual Oscilloscope - Medium
[1] At least 8 bits resolution
[2] 2x channels: BNC + external trigger [3] Voltage ranges +/- 50mV to 20V [4] Overload protection +/- 100V [5] Sampling rate at least 20Ms [6] Accuracy approx. 3% [7] Oscilloscope timebase: 100ns/div to
50s/div
[8] Frequency range 10MHz [9] To include power supply and output
connection to PC via parallel or USB port
[10] Software included L005 0008\19 Virtual Oscilloscope-
Fast [1] 8 bits resolution minimum
[2] 2x channels: BNC + external trigger [3] Voltage ranges +/- 50mV to 20V in 9
ranges
[4] Overload protection +/- 100V [5] Sampling rate at least 100Ms [6] Accuracy min. 3%
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 54 of 154
Lot Item Code Item Description Target Specifications Yes No [7] Timebase: from 100ns/div to 50 s/div [8] Frequency range 50MHz [9] To include power supply and output
connection to PC parallel or USB port
[10] Software included L005 0008\20 Aquisition Board [1] Sampling rate 10 to 15,000
samples/second or better
[2] Overload protection +/- 30V or better [3] Digital output 1 TTL or better [4] Output connector to PC, parallel or USB
port
[5] Software included [6] Sensors included: sound, voltage,
resistance, temperature, light, pH, humidity
L005 0008\21 Digital Multimeter With Bargraph
[1] Dual display: digital and analogue bargraph
[2] Measuring ranges: 400mV to 600V DC/AC; 40 mA to 10A DC/AC; 400ohm to 40Mohm; 4nF to 40uF and 100Hz to 200kHz
[3] With conductivity/diode tester [4] Accuracy for AC voltage ranges: +/- 1
digit; accuracy for AC current ranges: +/- 2 digit
[5] With overload protection and recognition of changes in measurement value
L005 0008\22 Digital Multimeter [1] Large digit LCD display [2] 1000Vd.c. & 750Va.c. measurement [3] 400mA & 10A fused current ranges [4] Resistance, audible continuity & diode
test
[5] Frequency & rpm counter (max 200KHz) [6] Frequency display (Hz) [7] Display hold [8] 30-minute auto power off L005 0008\23 AC Power Supply [1] Single phase primary [2] Secondary: 12 V AC, 20 VA [3] Connection: 4mm safety sockets L005 0008\24 DC Power Supply [1] DC power supply: voltage continuously
adjustable from 0 to 30 V
[2] Short-circuit protection [3] Adjustable current 0-3 A min. [4] Ripple voltage 1 m Vrms max. or better. [5] Load regulation 3% approx. [6] Voltage meter, current meter. [7] Test lead, 1 set. L005 0008\25 Waveform generator [1] For generating sine, triangular, square
wave or additional waveforms
[2] With DC offset [3] Frequency range: 10 Hz-10 MHz in 4
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 55 of 154
Lot Item Code Item Description Target Specifications Yes No ranges or more
[4] Output level: 0 dB to -40 dB [5] Output impedance at least 600 Ohm [6] Output sine wave: 10 Hz-10 MHz or
wider
[7] Output square wave: 10 Hz-100 KHz or wider
[8] Test lead 1 set. L005 0008\26 Digital Storage
Oscilloscope [1] Bandwidth: 0 to 50 MHZ or better
[2] Input impedance: 1 Mohm or better, 18 pF
[3] Screen: 8 x 10 cm with internal graticule [4] Time base: 0.5 s/cm...10 ns/cm, with X-
expansion x10 to 10 ns/cm
[5] Trigger source: CH1, Ch2, CH1 and Ch2 alternate, line and external
[6] Storage modes: refresh, roll, single, XY [7] Envelope, average, random sampling [8] 8 bit memory per channel [9] Sample rate: 100MSa/s or better [10] To include 100MHz probe and cable:
switchable, with spring-loaded hook tip; trimmer key, BNC adapter, probe tip, insulating covering, ground lead and 4-mm plug
L005 0008\27 Oscilloscopes [1] Dual trace, 20MHz bandwidth [2] 2x screened connector leads [3] 1mV/div sensitivity [4] CH1 Output [5] ALT triggering function L005 0008\28 Frequency Counter [1] To measure frequency, period, pulse
duration and ratio measurement, and event counting
[2] Input A input: switchable between TTL and analog signal; frequency range: 1 Hz to 10 MHz
[3] Input B input: frequency range: 0 to 2 MHz, TTL level
[4] Digital display: 8-digit, 10 mm high; [5] Gate times: 10 s, 1 s, 0.1 s, 0.01 s L005 0008\29 Notepad Computer [1] To act as interface for portable kits [2] Mobile Intel Pentium 4 processors - up to
3.06 GHz
[3] 256MB or more [4] Minimum to 60 GB hard drive [5] Integrated NIC [6] V.92 modem [7] 802.11b and 802.11g Wireless LAN [8] Full-size keyboard with 5 Quick Launch
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 56 of 154
Lot Item Code Item Description Target Specifications Yes No Buttons
[9] Microsoft Windows XP Professional [10] Pointing Device - Touch pad [11] One Type II PC Card slot with support
for 16-bit PCMICIA and 32-bit Cardbus
[12] 1.44 MB Diskette Drive [13] DVD/CD-RW combo Drive [14] Integrated Speakers L005 0008\30 PABX [1] Digital switching system, Euro-ISDN
compatible
[2] Capacity: 48 interior, 8 trunk [3] 20 digital terminals [4] 28 analogue terminals [5] DISA interface [6] ISDN interface [7] PC management L005 0008\31 Multimedia Projector [1] LCD Projector for connection to computer [2] Projection distance: Adjustable from
500cm to 10m, with brackets allowing fastening to wall or to ceiling
[3] Picture Brightness: 1,800 ANSI Lumens [4] Video Formats PAL, SECAM, NTSC,
NTSC-4.43, PAL-M and PAL-N format
[5] Contrast Ratio; at least 200:1 [6] Audio Stereo: built in speakers [7] With picture-in-picture technology, digital
zoom and freeze frame, remote control functions and digital keystone correction
[8] Connection Terminals: RGB input; audio Input (Mini jack x 2); RGB Output; USB mouse connection; AV Input (RCA) and ext. speaker outlet
L005 0008\32 Spectrum Analyzer For TV Cable
[1] Tunning range: from 5 to 862 MHz, 10KHz resolution
[2] Level measurement: from 25 to 120dBuV [3] Input impedance: 75ohm [4] Audio and video level carrier ratio form 0
to 40dB
[5] Carrier to noise level ratio measured within required channel >30dB measurement range
[6] Sound demodulation AM/FM [7] Transient detector [8] Accumulators with external fast charger [9] CSO-CTB intermodulation (Analogue
channels)
L005 0008\33 LAN Analyzer [1] Cable types supported UTP, STP, FTP, SSTP, RG6, RG59, audio, security
[2] Qualification autotests 1000BASET, 100BASETX, 10BASET, VOIP, 1394b
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 57 of 154
Lot Item Code Item Description Target Specifications Yes No S100,TELCO, Wiremap only, Coax
[3] Supported tests Wiremap, length, cable signal performance, digital toner, analog toner, Ethernet port detection and identification, analog telephone detection, blink port light, continuity, speaker test, cable fault finding, video signal detection
[4] Detects split pairs [5] Measures crosstalk and impedance and
compares against limits
[6] Detects location of large point sources as well as distributed sources in the cabling
[7] Stores up to 250 qualification test results L006 0009\1 Solid Handling Study
Bench [1] Bench-mounted apparatus for investigation of flow characteristics of solid materials including powders, pellets and aggregates
[2] Vibratory shaker and sieves for statistical analysis of particle size distribution comparison of sieving efficiency to screen size and vibration time
[3] Cylindrical hopper to compare discharge rates with exit orifice size and initial load
[4] Horizontal cylinder, to determine the density and angle of repose of bulk solids
[5] Solid mixing vessel, for batch mixing studies
[6] Ball mill with variable rotation speed [7] Cyclone and pneumatic system for
demonstration of conveying and subsequent cyclone action
[8] To include a balance refractometer and measuring cylinder
L006 0009\2 Micro Rotary Evaporator [1] Electrical stainless steel heating bath, capacity around 500 W, 1 litre
[2] 3x round-bottom receiving flask [3] Long inlet feed tube/stopcock [4] Long steam duct [5] Clamps [6] 3x evaporator glass flask, rotation speed
80 - 200 rpm, heating temperature regulated to 30-100°C, approx.
[7] Vertical glass cooler/condenser [8] All glass-to-glass standard taper joints [9] Four-way connector for vertical and
refrigerant condenser setups
[10] Motor and stand L006 0009\3 Distillation Column [1] To separate of mixtures of liquids made
up of single liquids that are soluble in each other by distillation and rectification or countercurrent distillation
[2] To include a reboiler to evaporate the liquid starting mixture, a column and a
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 58 of 154
Lot Item Code Item Description Target Specifications Yes No water-cooled condenser
[3] May be used continuously or batchwise, with and without reflux with two different columns: a sieve plate column and a packed column
[4] Sieve plate column fitted with feed connections to examine the separation behaviour at various heights
[5] Relevant measurements are recorded with sensors and displayed digitally and can also be transferred to a PC
[6] Sieve plate column to have minimum of 8 plates with overflow and packed column with Raschig rings
[7] Columns with 8 temperature measuring points
[8] Phase separation tank [9] Water jet pump for vacuum distillation [10] Bottom product heat exchanger [11] Three-phase electicity supply [12] PC data acquisition software using
USB, LabView software under Windows 98/XP/2000
L006 0009\4 Chemical Reactors Training Equipment
[1] Bench-top unit to allow experimentation on the kinetics of reactions and the conversion of reactants during a saponification reaction can be performed
[2] Experiments to include: variation of the contact time of the two chemicals, variation of the reaction temperature, adiabatic reaction in a batch reactor and isothermic reaction in a batch reactor
[3] To include combined measuring unit for conductivity 0 to 200mS and reaction temperature 0 to 100°C
[4] Hot water circuit with pump for moderating the reaction
[5] Electrical heater [6] Electronic two-point controller [7] Self-sealing rapid action hose couplings [8] Continuous stirrer tank reactor with
following characteristics:
[9] Overflow adjustable, reaction volume 0.4 to 1.5 litre approx.
[10] Glass tank wall and electrical motor stirrer
[11] Stainless steel heat exchanger coil and rapid action hose couplings
[12] Tubular flow reactor with following characteristics:
[13] Reaction tube wound into a spiral tube [14] Hose length 20 m, reactor volume 0.4
litre approx.
[15] Glass tank wall
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 59 of 154
Lot Item Code Item Description Target Specifications Yes No [16] Rapid action hose couplings [17] 3x stirred tank reactors in series with
flow delay section, with following characteristics:
[18] Capacity each 1 litre approx. [19] Glass tank wall [20] 3x electric motor driven stirrers [21] Delay section length 2.5 m approx.,
effective section capacity 0.2 litre
[22] Batch reactor for isothermic or adiabatic reaction with following characteristics:
[23] Tank designed as a Dewar vessel, additional foam insulation for the lid
[24] Reactor capacity approx. 1.0 litre [25] Electrical motor stirrer [26] Stainless steel heat exchanger coil and
rapid action hose couplings
L006 0009\5 Fixed And Fluidised Bed Apparatus
[1] Self-contained table unit for the observation and investigation of fluidised beds
[2] Observation of the fluidisation process in different media (air and water) and effect of particle size on fluidisation
[3] Measurement of pressure loss with air flow and water flow
[4] Allows determination of loosening speed, separation of mixtures or varying particle sizes and sedimentation
[5] Investigates the relationship between volumetric flow rate and height of the fluidised bed
[6] 2x tubes acting as test tanks, approx. 1.2 litres and 2-tube manometer, 0 to 500mm WG
[7] Diaphragm compressor for the air supply, max. 2.0 bar
[8] Compressed air reservoir 2 litre [9] Single tube manometer for air 0 to 2.0
kPa
L006 0009\6 Drying Cabinet [1] Stainless steel cabinet [2] Temperature controlled by digital thermo-
regulator
[3] Supplied with 3 metal shelves min. [4] Capacity 25 litres approx. [5] Temperature range 0 to 250°C L006 0009\7 Abbe Refractometer [1] Direct reading refractometer with digital
display
[2] LED lens illumination [3] Refractive index read directly from a
scale divided to 0.001
[4] Complete with digital thermometer, traceable standardisation plate and contact liquid
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 60 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Power supply [6] Sodium D line calibration tables L006 0009\8 Chomatography Set [1] Thin layer chromatography kit, student
type
[2] Glass chromatographic column, diameter = 50 to 60 mm, length: 1m max.
[3] Accessories: clamps, sieves for fixing the chromatographic bed, working bench, collector vessel
[4] Ellution solvent [5] Chromatographic bed [6] Washing solvent [7] Working standards [8 Stopwatch [8] Whatman chromatography paper [9] Working standards for paper
chromatography
L006 0009\9 Digital Turbidimeter [1] Range 0 to 2000 FTU [2] Pushbutton calibration and operation [3] Selected unit results display [4] Automatic performance of calculations L006 0009\11 Oven [1] Electrical laboratory oven, capacity
approx. 50 litres
[2] Approximate temperature range 40 to 200°C
[3] Electronic controller and safety back-up controller
[4] Natural convection [5] Supplied with 2 shelves [6] Minimum number of shelf positions 3 [7] Complete with thermometer and holder L006 0009\12 Soxhlet Extraction
System [1] Complete assembly with nominal capacity of 100ml
[2] Flask: round bottom, short neck, capacity 250ml, socket 24/29
[3] Extractor: nominal capacity 100ml, socket 40/38, cone 24/29
[4] Condenser, Allihn: effective length 250mm, cone 40/38
L006 0009\13 Mohr-Westphal Balance [1] For measuring liquid densities greater or less than water
[2] Capacity 0.0001 to 2.222 [3] Beam type [4] Beam riders [5] Hard sided case L006 0009\14 Centrifuge [1] Laboratory centrifuge, bench top [2] Maximum g: 2500 approx. [3] Max. speed, 5000 approx. [4] Timer: 0 to 30 minutes
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 61 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Complete with rotor and sleeves for 10x
6ml tubes
[] Supplied with set of 30 round-bottom glass tubes
L006 0009\15 Digital Colorimeter [1] Wavelength range: 440 to 700nm [2] Filter wavelengths: 440, 470, 490, 520,
550, 580, 590, 680
[3] Bandpass: 40nm [4] Resolution: absorbance, A 0.02 @ 1A ,
transmission, 2%
[5] Ranges: absorbance, V 0 to 1.99, transmission, 0 to 199%
L006 0009\16 Chemical Exhaust Hood (mobile)
[1] Bench top, vertical laminar flow cabinet
[2] Constructed from mild steel with epoxy powder coating
[3] Filters: 99.997% efficient at 0.3 microns [4] Low-air alarm system [5] External Dimensions: 1300 x 010 x 1300
mm min.
[6] Work Area Dimensions: 1200 x 680 x 700 mm min.
[7] Airflow: 0.30 to 0.55m/sec approx. L006 0009\17 Orsat Apparatus [1] Orsat apparatus [2] Fitted with glass pipettes for measuring
CO2 ,O2 and CO
[3] Storage case L006 0009\18 Water Analysis
Equipment [1] Portable, for field use
[2] Measures up to 24 water quality parameters
[3] Digital calorimeter [4] Titration testing [5] Ph meter [6] Reagent refill kit [7] Hard sided case L006 0009\19 Laboratory Still [1] Minimum output 3 litres per hour approx. [2] Electric heaters [3] Borosilicate glass construction [4] Output conductivity: <2.5uS/cm L006 0009\20 Water Still [1] Heater with built-in thermostat for low-
water protection
[2] Clear borosilicate glass boiler with coil-condenser and strong metal stand for bench or wall mounting
[3] Stopcock for draining [4] Distilled water output at 25° to 35°C for
up to 4 litres per hour
L006 0009\21 Precision Balance [1] Capacity 180g, readability 0.0001g [2] Pan diameter 75mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 62 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Standard three sided glass windshield [4] Detachable front panel [5] Below-pan weighing facility L006 0009\22 Balance Stand [1] Anti-vibration stand for balance L006 0009\23 Water Tester [1] Contaminants studied to understand
water pollution
[2] Use of test ions and reagents to determine positive test
[3] Includes materials for testing the following ions: chloride, nitrate, phosphate, magnesium, chromate, lead, and mercury
[4] Includes glass dropper and colour chart L006 0009\24 Fume Hood - Static [1] Constant volume/bypass air flow system
to remove fumes and vapours
[2] Two-speed blower and face velocity adjustment for wide range of duct conditions
[3] Laminated safety glass vertical sash [4] Inside dimensions: 450 x 800 x 1000mm
approx.
[5] Sash opening: 1/2 700 x 800 x 700mm approx.
[6] Interior illumination [7] With 10m ducting to outside L006 0009\25 Fume Hood Cabinet [1] Base cabinet for supporting fume hood [2] Two hinged doors [3] One adjustable shelf [4] Epoxy resin work surface L006 0009\26 Burette [1] For accurate fluid dispensing and
measuring
[2] With fully wrapped black markings [3] Capacity: 50ml [4] Calibrated at 20°C [5] Including: teflon stopcock L006 0009\27 Burette Clamp [1] For holding burette with 2 arms [2] Centre arm under spring tension [3] Rubber sleeve on each center arm [4] Heavy-gauge steel with stain-resistant
coating
L006 0009\28 Magnetic Stirrer [1] Rugged, chemical resistant housing [2] Plastic top [3] Speed range 100 to 1000 rpm [4] Capacity: 1 litre L006 0009\29 Density Meter [1] Oscillating tube method [2] LCD matrix [3] Measurement range: 0 to 2g/cc, [4] Accuracy: ±0.001g/cc L006 0015\6 Water Analysis
Multimeter [1] Parameter range: pH 0 to14, +/-1250mV, -5 to +110°C
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 63 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Resolution: pH 0.1, mV 1 or better [3] Accuracy: pH +/-0.1, +/-1/0.2 mV, +/-
0.1°C or better
[4] Temperature compensation: 0 to +100°C or better
[5] Setting range for ion selective measurement 0.01 to 999.9 mg/l
[6] Oxygen/BOD: 0.00 to 30.00mg/l and 30.0 to 300.0 mg/l; saturation 0.0 to 100.0% and 100 to 999%, Mbar: 0.0 to 300 and 300 to 250; temperature: -5 to +60 degree C
[7] Accuracy: +/-0.5% of value +/-1 digit [8] Salinity adjustment range: 0.0 to 99 [9] Includes: electrodes, temperature
sensors, calibration and maintenance supplies, universal pH simulator, magnetic stirrer, stand and electric holder, measuring and storage vessels
[10] ORP: electrodes, calibration and maintenance supplies
[11] Ion: sensitive electrodes, ISA/TISAB standard solution
[12] Oxygen/BOD sensors, sensor accessories, calibration and storage vessels
[13] Condutivity: cell, measuring cells for special applicators
[14] Photometry: reagents, solutions, free-tests
[15] Software, printer and accessories L006 0015\7 Weather Recording
Station [1] For measuring air pressure, rainfall, wind speed, sun hours and air temperature
[2] Allows connection to internet forecasts [3] Includes computer connection cables and
software
L006 0017\1 Veterinary Post Mortem Set
[1] Supplied in metal box for field use
[2] Comprises: bow saw, chopper, variety of knives, scissors, forceps, scalpels and needles
L006 0017\2 Livestock Multi-Dosing Set
[1] Multidose syringe, 50ml
[2] Gives 1, 2, 3, 4 or 5ml injections L006 0017\3 Artificial Insemination Kit [1] 100 of insemination tube, clear [2] 100 of shoulder gloves [3] 6 of syringes, 600ml [4] 6 of adaptors, syringe/AI tube [5] Supplied in carrying case L006 0017\4 Pregnancy Testing Kit [1] Internal Universal Pregnancy Kit [2] For sow, cow, mare and ewe [3] Ultrasonic system with internal & external
detectors
[4] Supplied with one set of headphones,
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 64 of 154
Lot Item Code Item Description Target Specifications Yes No battery and bottle of gel
[5] Training tape included L006 0017\5 Veterinary Diagnostic
Set [1] Ophthalmoscope with magnification up to 40x
[2] Otoscope with 2x magnification [3] Set of assorted speculae [4] Dilating speculum [5] Bent arm throat lamp [6] Examination mirror L006 0017\6 Hypodermic Needles [1] Set of 20 reusable needles for veterinary
use
[2] Sub-cutaneous, intra-muscular and intravenous
L006 0017\7 Goat Artificial Insemination Kit
[1] 2x large speculums
[2] 2x small speculums [3] 1x tweezers [4] 1x straw cutter [5] 1x insemination gun [6] 25x sheaths for gun [7] 1x thawing box for frozen straws [8] 1x metal AI thermometer [9] 1x AI light source [10] 1x tube lubricating jelly L006 0017\8 Pig Artificial Insemination
Kit [1] 2x large speculums
[2] 2x small speculums [3] 1x tweezers [4] 1x straw cutter [5] 1x pig insemination gun [6] 25x sheaths for gun [7] 1x thawing box for frozen straws [8] 1x metal AI thermometer [9] 1x AI light source [10] 1x tube lubricating jelly L006 0017\9 Gerber Fat
Determination Kit [1] Centrifuge for 6 to 8 tubes
[2] Electric drive with speed and time control [3] 20x Gerber test tubes L006 0017\10 Ultraviolet Lamp [1] For purifying the air and sanitizing work
surfaces
[2] Wavelength: 365 nm, intensity 750uW/cm2
[3] Dimensions: 600 x 150 x 100cm approx. [4] For ceiling mounting L006 0017\11 Water Still [1] Heater with built-in thermostat for low-
water protection
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 65 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Clear borosilicate glass boiler with coil-
condenser and strong metal stand for bench or wall mounting
[3] Stopcock for draining [4] Distilled water output at 25° to 35°C for
up to 4 litres per hour
L006 0017\12 Spatula [1] Combination of round blade and square blade
[2] Made of stainless steel with mirror-like finish
[3] Length: 22cm L006 0017\13 Test Tube Rack [1] 2 row, suitable for autoclaving [2] Capacity for approx. 15 tubes [4] Diameter of opening: 26 mm L006 0017\14 Dissection Set [1] 9 pieces stainless steel [2] Supplied in PVC roll L006 0017\15 Pipettes & Tips [1] 25x 200ml pipettes with rubber bulb [2] 1000x disposable, autoclavable, sterile,
polypropylene pipette tips
L006 0017\16 Erlenmeyer Flask, Small [1] Heavy duty top and wide mouth [2] Conical-shaped flasks [3] Graduated [4] White square marking space [5] Capacity: 250 ml L006 0017\17 Erlenmeyer
Flask,Medium [1] Heavy duty top and wide mouth
[2] Conical-shaped flasks [3] Graduated [4] White square marking space [5] Capacity: 500 ml L006 0017\18 Porcelain Mortar And
Pestle [1] Porcelain mortar with pouring lip
[2] Glazed outside, rough inside [3] Diameter: 100 ml L006 0017\19 Pharmacy Balance [1] Capacity 180g, readability 0.0001g [2] Pan diameter 75mm [3] Standard three sided glass windshield [4] Detachable front panel [5] Below-pan weighing facility L006 0017\20 Electronic Balances [1] Digital display of weight [2] Capacity: 300 - 500g; auto-cal calibration [3] Stainless steel pan and spill ring [4] Readability: 0.1g [5] Pan diameter: 120mm [6] RS232 socket L006 0017\21 Spirit Lamp [1] Metal or glass L006 0017\22 Culture Spreader [1] For spreading material on agar jelly for
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 66 of 154
Lot Item Code Item Description Target Specifications Yes No bacterial culture
[2] Made of glass L006 0017\23 Table For Instrument
Sets [1] Metal, with glass surface
[2] 80cm height min. L006 0017\24 Stands For Microscope
Slides [1] Metal stands
[2] Capacity: 200 slides min. L006 0017\25 Parasitology Testing Kit [1] Wills and Baerman techniques [2] For identifying parasitic eggs in faeces [3] Low power liquidiser [4] Including beakers, pipettes and 20
microscope slides
L006 0017\26 Surgery Pathology Instruments 1
[1 For incisions and sections
[1] Various scalpels, various scissors, saw, trepan, jales paper
L006 0017\27 Surgery Pathology Instruments 2
[1] For destroying and removing tissue
[2] Curettes, renettes, Buss knives, chisel, thermo-cautery, electric cautery
L006 0017\28 Surgery Pathology Instruments 3
[1] For linear sections, homeostasis and castration
[2] Ovariotom, castration clips L006 0017\29 Surgery Pathology
Instruments 4 [1] Instruments for homeostasis
[2] Haemostatic clips, garret (for stopping blood)
L006 0017\30 Surgery Pathology Instruments 5
[1] Instruments for tissue protection
[2] Anatomical and surgery clips, separators, clips for clipping the surgery field
[3] Instruments for suturing [4] Various surgery needles L006 0017\31 Surgery Pathology
Instruments 6 [1] Butonate, canelate and gastric probes for pathology drainage
L006 0017\32 Surgery Pathology Instruments 7
[1] Instruments for punctures, drainage and explorations
[2] Buttoned and canalled probes, gastric probes, catheter, rubber drainage tube, trocars
L006 0017\33 Surgery Pathology Instruments 8
[1] Instruments for injections
[2] Perfusion equipment L006 0017\34 Surgery Pathology
Instruments 9 [1] Instruments for special usages
[2] Buccal speculum, extraction tongs, shaving file, tracheotomy equipment, trachea cannel, tongs and saw for cutting horns
L006 0017\35 Set Of Kidney Bowls [1] Set of 8 renal rectangular plates, cassolettes, sterilizer (boiler), of various
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 67 of 154
Lot Item Code Item Description Target Specifications Yes No sizes and capacities
L006 0017\36 Obstetrical Instruments [1] For blooding and non-bloodinginterventions, examination of mammary glands and AI
[2] Vaginal speculum for cows and sheep, digital embryotome, mammary probe, mammary expander, obstetric spatulas, obstetric lines, front lamp, inoculation pistol
L006 0017\37 Bolus Thrower [1] Made of metal [2] Tube (approx 20 cm diameter) with piston L006 0017\38 Graduated Pipettes [1] For preparing medicines [2] Glass, graduated, autoclavable [3] Set of 10 capacities from 10ml L006 0017\39 Refrigerator [1] Net storage capacity: 170 litres approx. [2] Exterior finish: Stainless steel [3] Interior finish: Aluminium [4] Refrigerant: R134a [5] 2 x coated wire shelves with shelf clips [6] Micro-processor control with digital
display
[7] Fan assisted [8] Automatic defrosting L006 0017\40 Pharmacy Sieve [1] Metal sieve and plastic spoon [2] Mesh diameter: 0.1 to 1mm [3] External diameter of the sieve: approx.
10cm
[4] Supplied with pharmacy spoon L006 0017\41 Case For Medicines [1] Pharmacology: for medicine storage [2] Metal, with locks [3] 1.8 m height, approx. 1m width [4] Separanda compartment, venena
compartment and 4-6 shelf compartments
L006 0017\42 Detection Equipment [1] Parasitological examination, for trichinosis detection examination
[2] With display [3] Supplied with glass compressors, 6mm
width, divided into 14+14 microscopic stages
L006 0017\43 Consulting Table For Examining Small Animals
[1] Metal structure with tiled work surface
[2] Approx. 80cm height [3] Approx. surface dimensions 0.7 x 1 m L006 0017\44 Cases For Instruments [1] Pharmacologic, for keeping surgery
instruments
[2] Made of metal, with glass in the upper half of the doors and side walls
[3] Locking device [4] With 3 or 4 shelves L006 0017\45 Table For Interventions [1] Metal structure with tiled work surface
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 68 of 154
Lot Item Code Item Description Target Specifications Yes No On Small Animals
[2] Approx. 80cm height [3] Approx. surface dimensions 0.7 x 1 m [4] Supplied with metal rings for restraining
the animals
L006 0017\46 Scialithic Lamp [1] For mounting on the surgery room ceiling L006 0017\47 Stethoscopes [1] Membrane acoustic inlet [2] Two rubber tubes with metal/plastic ends
for ears
L006 0017\48 Veterinary Thermometer [1] Graduated glass with mercury [2] Triangular cross-section L006 0017\49 Veterinary Reflex
Hammer [1] Metal handle, approx. 25 cm length
[2] Tough rubber head, fixed to the handle with a metal ring
L006 0017\50 Isothermal Thermos For Seminal Material
[1] Cylindrical metal body, 2 litre capacity min.
[2] Low temperature maintained by liquid nitrogen
L006 0017\51 Nitrogen Tank, Small Capacity
[1] Liquid Nitrogen tank set for sperm storage
[2] Tank capacity min. 25 litres [3] Completed with all accessories including
special tong for holding work pieces
[4] Supplied with protective hand gloves L006 0017\52 Teaching Veterinary
Stethoscope [1] Standard veterinary stethoscope
[2] With two pairs of earpieces L006 0018\1 Egg Incubator [1] Capacity at least 240 eggs [2] Electronic temperature control [3] Forced air ventilation [4] Fully automatic turning L006 0018\2 Egg Candler [1] Single egg, hand-held model [2] Mains electricity operation [3] High intensity light [4] With spare bulb L006 0018\3 Poultry Feeder [1] Suspended cylinder type [2] Capacity approx 20 kg [3] Open top [4] Galvanised iron body [5] Includes suspension chain L006 0018\4 Poultry Drinker [1] Suspended fountain drinker [2] Approx 10L capacity [3] Heavy gauge enamel steel [4] Complete with suspension chain L006 0018\5 Bee Hive [1 National type hive or similar [1] Floor with alighting board, entrance
block, brood chamber, crownboard roof,
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 69 of 154
Lot Item Code Item Description Target Specifications Yes No queen excluder
[2] 1L brood chamber frames complete with foundation
[3] 2 supers/honey chambers [4] 22 super frames complete with wired
foundation
[5] Cedar construction, corrosion resistant roof
L006 0018\6 Bee Super Chamber [1] National type or similar [2] Chamber [3] 1L super frames complete with wired
foundation
[4] Cedar construction L006 0018\7 Wax Foundation [1] 30 sheets wired foundation for brood
chamber
[2] 100 sheets wired foundation for super chamber
L006 0018\8 Pin Hammer [1] For fitting foundation to frames in hives [2] Approx 100g head [3] Hardwood handle L006 0018\9 Smoker [1] Body galvanised iron/wood construction [2] Firebox approx 8cm diameter, 18cm high L006 0018\10 Hive Tool [1] 1x steel hive tool [2] 1x frame-lifter & scraper L006 0018\11 Honey Extraction
Centrifuge [1] Four frame tangential centrifuge
[2] Stainless steel cage and body [3] Manual operation [4] Includes tank & filter [5] Suitable for 4x supers or 2 brood frames L006 0018\12 Uncapping Knife [1] For cold uncapping [2] Stainless steel [3] 25 cm blade [4] Hollow ground blade L006 0018\13 Beekeepers Protective
Clothing [1] 5 hats with integrated veil
[2] 1 pair small beekeeping gloves, latex or similar
[3] 2 pairs medium beekeeping gloves, latex or similar
[4] 2 pairs large beekeeping glovers, latex or similar
L006 0018\14 Honey Filter [1] Stainless steel strainer [2] 100m fine straining cloth, 1 m wide,
minimum
L006 0018\15 Wax Extractor [1] For extracting wax from used honeycombs
[2] Solar operation L006 0026\9 Scales [1] Mechanical
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 70 of 154
Lot Item Code Item Description Target Specifications Yes No [2] With non-toxic weighing pan [3] Capacity 5kg L006 0026\10 Platform Scales [1] Capacity: 50kg x 100g [2] With non-toxic weighing pan [3] Bench standing L006 0027\4 Vortex Laboratory Mixer [1] For mixing culture samples [2] With continuously variable speed
adjustment from 600-3000 rpm approx
[3] With shaking and vibrating ranges [4] Automatic start and stop facility for
single-handed operation
[5] Includes both a 76 mm platform and a cup head
L006 0027\5 Variable Volume Pipette [1] Manually operated digital pipette [2] Digital display of volume setting [3] Volume adjusted via thumb activated
plunger
[4] Calibration facility [5] Volume: 200 to 1000 microlitres L006 0027\7 Sterile Pipette Tips
W/Rack [1] For use with manually operated plunger pipette
[2] Packed in sterile racks [3] Size: 1 to 200 microlitres L006 0027\8 Sterile Pipette Tips
W/Rack [1] For use with manually operated plunger pipette
[2] Packed in sterile racks [3] Size: 101 to 1000 microlitres L006 0027\10 Refrigerated Incubator [1] For incubation of micro-organisms [2] Holds 6 shelves, total area of 1.6 sq
metres plus 0.5 sq metres of storage space in door
[3] Features temperature set-point selection, high and low temperature protection, digital display and front panel calibration
[4] Includes analog recorder output and access port for auxiliary equipment within the chamber
[5] Steel exterior with powder-coated finish [6] Porcelain steel interior with forced air
convection duct work
[7] Stain resistant shelves and steel supports [8] Includes magnetic door gasket, door lock,
interior light
[9] Capacity: approx 0.6 cubic metres [10] Temperature range: -10°C to + 50°C,
with +/- 0.5 deg C uniformity at 20°C
L006 0027\11 Illuminated Incubator [1] For incubating micro-organisms under standard or lighted conditions
[2] Holds 6 shelves with total area of 1.6 square metres, plus 0.5 square metres of storage space in door
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 71 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Two fluorescent lamps [4] Microprocessor controlled temperature
setpoint selection, high and low temp. protection, digital display, and calibration
[5] Programmable heating/light cycles for accurate simulation of diurnal conditions
[6] Chamber environment can be programmed for 2 heating/light cycles per day for 7 days
[7] Steel exterior with stainless finish [8] Includes analog recorder output and
access port for auxiliary equipment within chamber
[9] Capacity: approx. 0.5 cubic metres [10] Temperature range without light: -10°C
to +50°C
[11] Temperature range with light: 10°C to 50°C, uniformity +/-1.4°C at 20°C
L006 0027\12 Adjustable-flame Burner [1] For sterilizing inoculating loops and needles and culture tube mouths
[2] Flame adjustable from 20 to 300 mm [3] Heat output over 5000 BTU/hr [4] Device to prevents flame lifting or
extinguishing
[5] Adjustable air and gas controls [6] Tapered, serrated gas connection [7] Non-ferrous, rustproof construction [8] Model intended for use with LP gas [9] Requires ignition device L006 0027\13 Safety Gas Lighter [1] Used for igniting burner L006 0027\14 Water Bath [1] For warming and holding media at given
temperature
[2] Programmable microprocessor-based temperature control to 100°C +/- 0.1°C
[3] Control provides +/- 0.24°C uniformity, +/- 0.5°C stability +/- 0.5°C accuracy at 37°C
[4] Corrosion resistant exterior [5] Covers opening to 90° position,
removable to accommodate large glassware
[6] Heating elements protected against running dry
[7] Stainless steel reservoir and perforated sample tray
[8] Capacity: approx 20 litres L006 0027\15 Gram Stain Set [1] For staining micro-organisms by the
differential Gram method
[2] Includes one 250 ml bottle each stabilized Gram iodine, Gram Crystal Violet, Gram Safranin, and Gram Decolourizer
[3] Includes reagent bottles with stay-clean caps and tray/workstation
[4] Stabilized Gram Iodine requires no
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 72 of 154
Lot Item Code Item Description Target Specifications Yes No mixing and has 18 month shelflife
L006 0027\16 Reusable Petri Dishes [1] For use in growing micro-organisms [2] Flat clear dishes with beaded edges [3] For repeated sterilization [4] Resistant to blooming or fogging [5] Tops marked in blue, bottoms marked in
white with reference points for serial dilutions
[6] Size: min 100 x 15 mm (dia x height) L006 0027\17 Culture Tubes [1] For use in growing micro-organisms [2] Round bottom [3] Made of borosilicate glass [4] Tubes can be capped or plugged [5] Size: approx 20 x 150 mm (outside
diameter x length)
L006 0027\18 Closure For Culture Tube
[1] For capping plain end culture tubes
[2] Keeps tube contents sterile without cotton plugging
[3] Polypropylene, autoclavable [4] Red, yellow, blue, green [5] Outside diameter: 20 mm L006 0027\19 Tube With Screw Cap [1] For growing cultures of micro_organisms
when a screw cap is necessary
[2] Round-bottom tubes with marking spot [3] Fully autoclavable [4] Size: min 13 x 100 mm (outside diameter
x length)
L006 0027\20 Test Tube Rack [1] 2 row, suitable for autoclaving [2] Capacity for approx. 15 tubes [4] Diameter of opening: 26 mm L006 0027\21 Stainless Steel Basket [1] For use in hot applications such as water
bath
[2] Autoclavable [3] Withstands acid and alkali solutions [4] Spot-welded construction L006 0027\22 Autoclaving Basket [1] Holds labware during autoclaving and
washing
[2] Allows complete venting and draining [3] Smooth surface will not scratch plastic or
glass
[4] Nestable for storage L006 0027\23 Bacteriological Slant
Rack [1] Shelf unit for preparing, storing and incubating cultures in tubes
[2] Holds tubes at 5° to 10° angle, adjustable [3] Polished stainless steel [4] Three shelves with separators, each
holding 12 tubes up to 20 mm dia x 160 mm long
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 73 of 154
Lot Item Code Item Description Target Specifications Yes No L006 0027\24 Apt Broth [1] Microbiological media for growing
bacteria
[2] All-purpose broth [3] Agar can be added to make solid media [4] Supports the growth of a wide range of
bacteria
[5] Size: 500 grams L006 0027\25 Baird Parker Agar Base [1] Microbiological media for growing
bacteria
[2] Size: 500 grams L006 0027\26 Innoculating Needles [1] For field sampling [2] Meeting ASM and EU standards [3] 200mm handle L006 0027\27 Inoculator Loops [1] For field sampling [2] 26 gauge meeting ASM and EU
standards
[3] 200mm insulated handle [4] Loop: 3 mm L006 0027\44 Temperature And
Humidity Tester [1] Hand held instrument
[2] Battery operation [3] Single keypad button operation [4] Range 0 to 60°C. 10 to 90% RH. [5] Resolution 0.1% RH 0.1°C. [6] Accuracy +-3% RH +-0.5°C. L006 0027\45 Salinity Tester [1] Hand-held battery powered refractometer [2] Range: 0 to 100% L006 0027\46 Circulator Water Bath [1] Temperature range: 0-99°C [2] Volume: approx. 35 l [3] Bath dimensions: 700 x 300 x 200 mm
approx.
[4] Power: 1.4 kW L006 0027\47 Laboratory Disc Mill
Universal [1] For grinding samples of grain, high fat and fibrous items
[2] Motor power: 350 W [3] Grinding disks: 60mm diameter, approx. L006 0027\48 Colour Comparator [1] Measuring range: 0 - 100, resolution 1 [2] Measuring angle: 20 - 60 degrees [3] Measuring surface: 60 degrees (6 x
3mm), 20 degrees (4 x 3mm)
[4] Reproductibility: +/-5% PE, +/-1 digit [5] Gardner, Hazen/APHA/Pt-Co., Iode
levels
L006 0027\49 Universal Centrifuge [1] Bench Top Centrifuge, max. speed 15,000 rpm
[2] Swing out 4-place 200 ml rotor and 6 x 50ml Angle Rotor
[3] Set of 4x 50ml buckets & 200ml slotted cup with sealing cap
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 74 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Set of adaptors for 100ml, 50ml, 15ml,
7ml, 5ml
L006 0027\50 Biological Oxygen Meter [1] Range: 0 - 19 mg/l [2] LCD display [3] Automatic temperature compensation [4] Accuracy: +/-1.5% FS [5] Two-point calibration [6] With probe and membrane kit L006 0027\51 CO2 Tester [1] For determination of CO2 content of
alcoholic and non-alcoholic drinks
[2] Manometer: 0 to 2.5 bar. [3] Thermometer: -2 to 20 degree C [4] Slide rule: bar/ degree C/weight % [5] Complete with service-set L006 0027\52 Cell Counter [1] For the determination of yeast cell
numbers
[2] Consists of cell counter, diluter, solutions and consumables
[3] Counting time: 10 sec, approx. [4] Transducer: single 0.008 mm capillary [5] LCD display [6] Calibration: WCB, RBC, PLT- factory
calibration; HCT (MCV) - keyboard calibration; HGB-zero-automatic and HGB- standard keyboard calibration
L006 0027\53 Automatic Potentiometric Titrator
[1] Programmable , microprocessor controlled automatic titrator, utilising potentiometric principle.
[2] Types of titration: Acid/Base in aqueous solution, Acid/Base in non-aqueous solution, Redox, Precipitate, Karl Fischer
[3] Able to determine water content by using Karl Fischer option.
[4] 2x RS232 ports for connection to PC or balance, and printer, complete with cables.
[5] Digital display with graphics capability. [6] Dosing unit. [7] Stirring unit. [8] Complete with all necessary accessories,
including Electrodes and electrolyte for titration methods listed above and Karl Fischer equipment;
[9] Includes one set each of sample racks 12 x 250ml, 16 x 150ml, sample beakers 24x 250ml, 24 pcs; Sample beaker 36x 150ml, 32 pcs;
[10] Supplied with analysis software, inkjet printer and sample changer and stabiliser
L006 0027\54 Water Analysis Multimeter
[1] Multi-function meter for measurement of pH, mV, temperature, oxygen/BOD, and conductivity
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 75 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Parameter range: pH 0 to 14, +/-
1200mV, temperature: 0 to +110°C, or better
[3] Setting range for ion selective measurement: 0.01 to 999.99 mg/l
[4] Oxygen/BOD: 0.00 to 30 mg/l and 30 to 300 mg/l; temperature: 0 to +60°C or better
[5] Accuracy: +/-0.5% of value +/-1 digit [6] Salinity adjustment range: 0.0 to 99.9 [7] pH measurements: electrodes,
temperature sensors, calibration and maintenance supplies, universal pH simulator for checking all pH meters and pH fields instruments and cables, magnetic stirrer, stand and electrode holder, measuring and storage vessels
[8] Ion: sensitive electrodes [9] Oxygen/BOD: sensors, sensors
accessories, calibration and storage vessels
L006 0027\55 Moisture Analyzer [1] Accuracy: 1 mg, or better [2] Readability: 0.01%, or better [3] Maximum weighing capacity: 40g approx. [4] Timer setting: 1 to 450 minutes approx [5] Temperature setting in 5°C increments [6] Display: % moisture content, % dry
weight
[7] With printer and cables L006 0027\56 Digital Heavy Metal
Analysis Meter [1] Vessel: 5 litre, glass
[2] Aeration: 50 micron mesh [3] Inlet gas low: airflow 0.2 l/min, oxygen
0.1l/min, nitrogen 0.1l/min, carbon dioxide 0.1l/min
[4] Outlet gas: 2 micron filter [5] Marine type inpeller 80mm diameter, 2
buffers
[6] Temperature control: electric heating sytem, system cooling system, recirculating pump
[7] Measurement and control: built-in peristaltic pumps, analogue output (voltage/current), port for printer/plotter
[8] Sensor ranges: temperature measurement Pt 100 ohms (max 65°C), proximity sensor for speed measurement, pH control, gel filled autoclavable probe, pO2 control 12ml "INGOLD" autoclavable probe (0 -140%)
L006 0027\57 Fat Analysis [1] Solvent-free fat analysis [2] System comproses system
controller/pump and one extraction module
[3] Supplied with two coaxial heated linear restrictors and extraction cartridges
[4] Extraction range: 0.1% to 100% fat
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 76 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Measurement technique: direct or indirect
gravimetric
[6] Analysis time: 15 to 30 mins typical [7] Precision target: RSD less than 0.8% at
10% fat
[8] Sample size: 0.5 - 4.0g typical L006 0027\59 Protein Analyzer [1] Digestor specification: temperature
range: 100 to 440°C with repeatability: 1°C, or better
[2] Heating time: approx. 40 minutes [3] Sample size, solids: Up to 5 g [4] Sample size, liquids: Up to 15 mL [5] Distilling unit specification: distillation
time max. 3.5 min, cycle time total max. 4.5 min, capacity up to 40 ml/min and reproducibility 1% relative (including digestion step)
[6] Tube draining: 200 mL in 2 sec. [7] Reagent volume: 0 to 150 ml [8] The unit consists of built-in steam
generator, complete with alkali/water/receiver/waste tanks with level sensors, receiver flask, drip tray for receiver flask and flask and test tube adapters and scrubber
[9] Pump flow rate: min 15 litre/min [10] Accessories for digestor to include:
stand for 20 tubes: 1 set; heat shield: 2 pcs; digestion tube, 250mL: 20 pcs.
L006 0031\1 Laboratory Crusher [1] Manganese jaws [2] For the crushing of aggregates, samples
and similar materials
[3] Jaw opening 100 x 60mm and crush rate up to 400kg per hour
[4] Jaw opening adjustable from 2 to 15mm approx.
L006 0031\3 Safety Protection Cover [1] Safety screen with micro-switch [2] Accessory for crusher and jar mill L006 0031\4 Hard Porcelain Grinding
Jar 1.5l [1] Capacity 1.5 litres
[2] Made from aluminous porcelain and fired at high temperature
[3] Mohs hardness 8.5 [4] Supplied with grinding media [5] Approx. 160 dia x 200mm high L006 0031\5 Analytical Sieve Shaker [1] Suitable for wet and dry sieving
operations
[2] Measurement range 20 microns to 125 mm from a maximum sample quantity of 3 kg
[3] Heat insulated with refractory bricks and pre-formed ceramic fibre sheets
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 77 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Test material moved along the kiln by
ceramic rollers
[5] Zones containing heating elements controlled by potentiometric pyrometer
[6] Roller dia. 20mm [7] 3x digital temperature
indicators/adjusters
[8] Max. temp 1340 degrees C [9] Maximum size of test piece 150 x 150 x
20 mm
L006 0031\6 Sieve Shaker Accessories
[1] For use with analytical sieve shaker
[2] Clamping device [3] Basic stainless steel cover with threaded
retaining nuts
L006 0031\7 Accessory Sieves [1] For use with analytical sieve shaker [2] Stainless steel framed stainless steel
mesh test sieves 200mm dia to BS 410:86, ISO3310/1
[3] Supplied with the following apertures, 2, 1, 0.5, 0.25, 0.125, 0.090 and 0.063mm
L006 0031\8 Stainless Steel Receiver Pan
[1] For use with analytical sieve shaker
L007 0012\1 Chain Saw [1] For sectioning small logs in the workshop [2] Bar length: approx. 400mm [3] Power: approx. 1500W L007 0012\2 Veneer Cutting Machine [1] For preparing veneer edges before
joining
[2] Guillotine action [3] For veneers up to 900mm wide L007 0012\3 Universal Milling
Machine [1] Working table min. 1200 x 600 mm.
[2] Worktable height: 800mm approx. [3] Spindle diameter: 30mm [4] Spindle stroke: 150mm [5] Spindle speed: up to 1700rpm [6] Max. depth: 90mm [7] Shaft angle: adjustable from -45° to +45° [8] To include 10 different profiled milling
cutters
L007 0012\4 Single End Tenoner [1] Used for producing tenons and carvings necessary for joining wooden pieces
[2] Length: maximum 120 mm [3] Width: maximum 370 mm [4] Thickness: maximum 100 mm [5] Max. tenoning cutterhead size: 100 mm
(dia.) x 150 mm (long)
[6] Max. shaping cuter size: 250mm [7] Max. sawblade diameter: 300mm [8] Tenon spindle: 25mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 78 of 154
Lot Item Code Item Description Target Specifications Yes No [9] Cope spindle: 25mm [10] Saw blade: 25mm [11] Cope spindle speed:approx. 3500 rpm [12] Sliding table area: maximum 1300 x 400
mm
L007 0012\5 Wood Jointer [1] Maximum table area 2000 x 300 x 100 mm
[2] Maximum planning width: 300 mm [3] Maximum table height (angle): 800 mm [4] Fence slant: 0° to 45° [5] Motor: minimum 3HP [6] Cutter head speed: maximum 5000 rpm L007 0012\6 4-Side Planer And
Moulder [1] Used for simultaneous processing of two sides and two edges, planing or moulding in a single process
[2] Aproximate table size: 2,000 x 400mm [3] Capacity (minimum / maximum): 20 x 10
mm / 180 x 120 mm
[4] Minimum stroke length: 300 mm [5] Cutter block speed: 6000 rpm [6] Feed rate: 8 - 16 m / min. [7] Motor for bottom cutter head: 2 HP [8] Motor for top cutter head: 2 HP [9] Motor for left vertical cutter head: 2 HP [10] Motor for right vertical cutter head: 2 HP L007 0012\7 Continuous Auto
Assembly Press [1] Length Assembled: 4m max.
[2] Maximum Power : Sawing 3HP ; Hydraulic pump 5HP
[3] Maximum Speed : 25 m/min [4] Aproximate working capacity (LxWxH) :
3,000-4,600 x 22-150 x 18-75 mm
L007 0012\8 Gluing Machine [1] Maximum working table: 500 x 800mm [2] Sawing power: 3hp [3] Sharping 15hp [4] Hydraulic pump: 2hp [5] Speed: 14 seconds/cycle L007 0012\9 Six Spindle Boring
Machine [1] Six separate motors
[2] Maximum spindle speed: 2500 rpm [3] Stroke: 0 - 100mm [4] Drill bit size: 8mm x 1.25 [5] Max. working length: 2000mm L007 0012\10 Drum Sander [1] Aproximate sanding width: 400mm [2] Aproximate work piece height: 120mm [3] Aproximate sanding depth: 3mm [4] Aproximate drum speed: 1600 rpm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 79 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Feed speed: 0 - 700mm [6] Drum diameter: approx. 120 mm [7] Dust hood L007 0012\11 Horizontal / Vertical
Sander [1] Aproximate table size: 1300 x 350mm
[2] Aproximate dimension of sanding belt: 1300 x 150mm
[3] Speed: 3500 rpm L007 0012\12 Finishing Sander [1] Aproximate pad size: 90x180 mm [2] Paper size: 90 x 200 mm [3] Motor: approx. 250 W L007 0012\13 Dowel Cross-cut And
Chamfering Machine [1] It is used for cross-cutting and chamfering dowels necessary for different joining operations
[2] Working diameter: 5 to 20 mm [3] Working length adjustable from 20mm to
150mm approx.
[4] Cutting speed: aproximately 40 pieces/min
L007 0012\14 Dowel Milling Machine [1] Used for milling round dowels necessary for joining wooden pieces
[2] Working diameters : 5 to 20 mm [3] Minimum working length: 200 mm [4] Feed speed: maximum 10 m/min L007 0012\15 Edge Banding Machine [1] Used for banding edges to wooden
panels
[2] Workpiece width : 50 mm to unlimited [3] Workpiece thickness : 8 to 50 mm [4] Edging thickness : 0.3 to 3mm L007 0012\16 Wood Drying Kiln [1] Internal dimensions: 5m x 3m x 2.5m
approx.
[2] Kiln opening: maximum 2000 x 1000 [3] Kiln wall: brick 200mm [4] Number of blower: maximum 5/kiln [5] Blower diameter: maximum 600mm L007 0012\17 Dust Collector [1] For collecting dust from power machines [2] Motor power: maximum 2 hp [3] Tube diameter: maximum 200mm [4] Collection capacity: 4 cubic metres L007 0012\18 CNC Wood Milling
Machine [1] Approximate motor power: 3 HP
[2] Speed range: 10000 -20000 rpm [3] Maximum feed rate: 1200 mm/min [4] Repeatability: approximately 0.05 mm [5] Resolution: approximately 0.025 mm L007 0012\19 CNC Wood Lathe [1] Bed: maximum 900 mm [2] Spindle motor: 50-3500 rpm,
programmable
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 80 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Two axis simultaneous interpolation [4] Repeatability: approximately 0.001 mm [5] Resolution: approximately 0.002 mm [6] Feed motor rate: 2 to 120 mm/min L007 0012\20 Manual Painting System [1] Including painting gun, electric stabiliser,
pump, spray booth
[2] Water booth dimension aproximately 4m x 1m x 2.3m
L007 0012\21 Wood Moisture Meter [1] Wood water content displayed by red, yellow and green lights
[2] Automatic temperature correction [3] Calibration check included [4] Dimensions: approximately 20 x 10 x
3cm
L007 0012\22 Wood Carving And Wood Turning Chisel Set
[1] Set of wood carving tools in wallet plus
[2] Set of carbon steel wood turning chisels with ash handles
[3] Minimum length 400mm [4] Set to include: 6mm, 12mm, 16mm
gauge, parting tool, 12mm round nose, 12mm diamond point, 12mm and 25mm skew chisel
L007 0012\23 Air Press [1] Used for joining frames [2] Joint length: maximum 2500mm [3] Joint width: maximum 1200mm [4] Joint thickness: maximum 100mm [5] Pressure sections: 8 [6] 4x air-operated power cylinder [7] Piston air pressure: 4 bar to 6 bar L007 0012\24 Single Needle Industrial
Sewing Machine [1] For use with semi-finished fabrics
[2] Sewing speed: 5500 strokes per minute [3] Maximum step: 4mm [4] Forward and reverse feed [5] Foot pedal operation [6] Power: approx. 0.4 kW [7] Includes table L007 0012\25 Pneumatic Stapler [1] For fastening textiles, linen and belt
straps to furniture and upholstery
[2] Suitable for staples 8 to 14 mm in length [3] Operating pressure 3 to 6 bar L007 0012\26 Portable Cutting-out
Machine [1] For cloth or multi-layer material
[2] Disc diameter: 60 to 140 mm [3] Cutting off height: 60mm approx. [4] Power: maximum 0.3 kW L007 0012\27 Air Compressor [1] For use with compressed air equipment
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 81 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Tank: min. 80 litres [3] Opperating pressure: 0 to 8 bar L007 0012\28 Electric Spray Gun [1] For use in finishing and spraying [2] Reservoir capacity: approx. 1 litre [3] Nozzle diameters: 0.6mm and 1.0mm L007 0012\29 Safety Helmet With Ear
Muffs And Visor [1] Fully adjustable head harness
[2] High density polyethylene shell and clear polycarbonate visor
L007 0012\30 Safety Boots [1] Leather boot [2] Steel midsole for underfoot protection [3] Universal size L007 0012\31 Work Gloves [1] Natural rubber medium weight. 400mm
approx. length
[2] Universal size L007 0012\32 Respirator Mask [1] Reusable mask [2] Lightweight holder with foam seal and
twin strap harness
L007 0012\33 Safety Apron [1] Leather apron L007 0012\34 Tape Ruler [1] Measuring tape: steel [2] Length: 5m, [3] Blade width: 25 mm L007 0012\35 Carpenter's Square
(steel) [1] Length : 200mm .
[2] Fold ruler : 200mm L007 0012\36 Aluminium Levelling
Float 2m [1] Width approx. 100mm
[2] Manufactured from thick walled aluminium extrusion
[3] One horizontal and one vertical vial [4] Milled working faces L007 0012\37 Aluminium Levelling
Float 1.5m [1] Width approx. 100mm
[2] Manufactured from thick walled aluminium extrusion
[3] One horizontal and one vertical vial [4] Milled working faces L007 0012\38 Aluminium Levelling
Float 1m [1] Width approx. 100mm
[2] Manufactured from thick walled aluminium extrusion
[3] One horizontal and one vertical vial [4] Milled working faces L007 0012\39 Plumb Level [1] Plumb and spirit level [2] Made of aluminium [3] With 600mm tubes L007 0012\40 Aluminium Ladder [1] Height: 2 metres [2] Folding
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 82 of 154
Lot Item Code Item Description Target Specifications Yes No L007 0012\41 Nail Extractor [1] Manufactured from nickel-chromium steel [2] Hardened jaws [3] High density cushion insulated grips [4] Approximate length: 180 mm L007 0012\42 Club Hammer [1] Head with two square impact faces [2] Forged alloy steel, head faces polished
and edge chamfered, head securely wedged, hickory or ash handle
[3] Length: 300 to 350mm [3[ Weight: 1800g L007 0012\43 Nail Extractors [1] Manufactured from nickel-chromium steel [2] Hardened jaws [3] High density cushion insulated grips [4] Approximate length: 180 mm L007 0012\44 Carpenter's Mallet [1] Face diameter: 400mm [2] Head length: 50mm L007 0012\45 Hand Tools And
Measuring Tools [1] Tapping set and screw cutter M3 to M14
[2] Precision dial diameter gauges: resolution: 0.01mm, measuring range: 5 mm, range of indication: 5.4 mm
[3] Square rules: hardened steel, accuracy DIN 875, wooden case, dimensions: 40 x 30mm
[4] Angle rules: blade: 200 mm, measuring range: 4 x 90°, hardened stainless steel
[5] Set of tools: monkey-wrench, hand-hammer, screw-driver, steel chisel.
[6] Micrometer: 0-25; 25-50; 50-75; 75-100; 100-125 mm, resolution 0.01 mm
[7] Compass [8] Pliers set: consisting of electric pliers,
cutting pliers, small nose pliers.
[9] Precision dial gauge: resolution: 0.01 mm, measuring range: 10 mm, range of indication: 10.5 mm
[10] Hex key: 6 pcs [11] Wrenches 8, 10, 12, 14, 16, 18, 20, 22,
24, 26, 28, 30, 32 mm
[12] Files set: consist of flat, square, triangle types
[13] Screw-driver set: consist of 2-edged and 4 edged long type, 2-edged and 4 edged short type
[14] Tape measures: 600 and 1000mm L007 0012\46 Marking Gauge [1] For marking lines parallel to the edge L007 0012\47 Outside Calipers [1] Vernier with thumb lock [2] Range: 0-250mm [3] Vernier: 0.02mm reading L007 0012\48 Centre Punch [1] Chrome vanadium or cast steel
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 83 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Diameter of shank: approx. 12mm [3] Length: maximum 150mm L007 0012\49 Spirit Level [1] Comprising two tubes, graduated +5 to -
5cm with 5mm marks, sealing caps
L007 0012\50 Glass Cutter [1] Cutter with flow valve system and cutting fluid reservoir.
[2] Supplied with standard 134 degree small cutting wheel for oil cutting.
L007 0012\51 Short Plane [1] For planing small surfaces [2] Length: 250 mm. [3] Width blades: 40mm L007 0012\52 Jack Plane [1] For planing long surfaces [2] Length: 550 mm approx. [3] Width blades: approx. 55mm L007 0012\53 Smoothing Plane [1] Used for finishing or smooth planing [2] Length: 180mm. [3] Width blades: 20mm L007 0012\54 Horizontal Chisel [1] Plane body made from iron [2] Length: 200mm approx. L007 0012\55 Mortise Chisel Set [1] Used for manual carving and chiselling [2] Blade widths: 6, 8, 10, 12, 15 mm [3] Dia: 150 to 180mm L007 0012\56 Bussing Chisel Set [1] Used for manual carving and chiselling [2] Length: 150 to 180mm [3] Blade widths: 20, 25, 30 ,40, 60 mm L007 0012\57 Screwdriver Set [1] Insulated vanadium steel blade [2] Four straight slot drivers: 3 x 75mm, 4 x
100, 6 x 125mm and 8 x 150mm, approx.
[3] Two Phillips drivers: N°1 x 75mm and N°2 x 100mm, approx.
[4] Two Posidrive drivers: N°1 x 75 and N°2 x 100mm, approx.
L007 0012\58 Hand Saw [1] For manual rectilinear cutting [2] Blade length: 500mm [3] Blade width: 35 to 40mm L007 0012\59 Carpenter Work Table [1] Steel frame with wooden work surface [2] Tool drawer [3] Length: 2200 x 200 x 750mm L007 0012\60 Bench Vice [1] Jaw width: 100mm [2] Anvil back: 70 x 70mm. [3] Cast iron with replaceable steel jaws L007 0012\61 Hand Planer [1] Speed: approx. 15,000 rpm [2] Planing width: maximum 140m [3] Removal depth: maximum 3mm [4] Total length: maximum 450 mm [5] Motor: approx. 1kW
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 84 of 154
Lot Item Code Item Description Target Specifications Yes No L007 0012\62 Planer [1] Cutting width: maximum 310 mm [2] Removal depth: maximum 3mm [3] Planing capacity: 8.5 m/min [4] Speed: 8500 rpm [5] Power: 1.5Kw approx L007 0012\63 Hand Sander [1] Power: maximum 200W [2] Speed: approx. 10,000 rpm L007 0012\64 Portable power tool [1] Electric hand drill for wood [2] Reversible drive [3] Drill bit capacity: 1 to 13mm L007 0012\65 Hand Circular Saw [1] Power:approx 1500W [2] Speed: maximum 4500 rpm [3] Diameter: approx. 180mm. [4] Complete with 50 assorted discs L007 0016\52 Carpentry Hand Kit [1] Tenon saw approx. 30 cm [2] Rip saw approx. 50 cm [3] Crosscut saw approx. 50 cm [4] Hammer [5] Set of 12 screwdrivers for straight and
Posidrive screws
[6] 5m retractable steel tape [7] Steel metre rule [8] Steel 30cm rule L007 0016\53 Hand Drill [1] Double insulated, with pistol grip and side
handle for left or right position
[2] Continuous variable speed between 0 and 2500 rpm
[3] Complete with chuck, chuck key and approx. 3m rubber covered cable
[4] Drilling capacity in steel: 10mm [5] Percussion facility L007 0016\54 Set Drill Bits In Case [1] 6x high speed steel bits: 3 to 8mm [2] 4x mason bits 5 to 8mm [3] 4x wood bits 4 to 8mm [4] 4x flat wood bits approx. 13 to 32mm L007 0019\1 Forestry Machinery
Toolkit [1] Supplied in steel tool chest
[2] Open ended wrench set 8 to 24mm [3] Open socket wrenches 7, 8 ,10 ,11 ,13
,17 ,19 and 24mm
[4] Adjustable wrenches 150 and 300mm [5] Screwdriver set for slotted, Phillips and
Posidrive screws
[6] Combination pliers, diagonal cutters and multigrip pliers
[7] Includes: hacksaw frame and blades, club hammer, riveting hammer, chisel, 2m tape rule and oil can
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 85 of 154
Lot Item Code Item Description Target Specifications Yes No L007 0019\2 Bench Chain Breaker [1] For repairing chainsaw chains [2] Complete with range of punches and
anvils
L007 0019\3 Chain Filing Kit [1] Vice-bench type [2] Set of 20 replaceable chain guides and
rollers and angle guides
[3] Set 12 assorted files L007 0019\4 Pedestrian Operated
Tractor [1] For soil preparation in restricted areas
[2] With steering brakes and 3x forward, 2x reverse and travel speed gears
[3] Petrol engine 9hp min. [4] Dead man safety cut out [5] Wheels 5.00 x 10 agricultural tread [6] Includes: pair spade lug wheels dia.
48cm to 50cm and rotary transport tiller wheel
[7] Reversible plough [8] Rotary cultivator working width at least
60cm
[9] Adjustable ridger, furrow width 10 to 30cm
[10] Two wheel trailer L007 0019\5 Seed Cleaning And
Grading Equipment [1] For separating different sizes of seed and cleaning seeds
[2] Aluminium frame [3] Stainless steel folding arms [4] Approx. 46 cm [5] Complete with bag with reinforced
heading
L007 0019\6 Two-wheeled Trailer [1] Flat bed [2] Hydraulic tipping [3] Removable solid sides approx 60 cm [4] Minimum 4 tonne capacity [5] With tow bar L007 0019\7 Load Binder [1] For fastening timber to trailer [2] 8m long [2] Hook ends L007 0019\9 Mounted Mouldboard
Plough [1] 2 Furrow
[2] Semi-digger bodies [3] Working width 60cm [4] Maximum working depth 20 cm L007 0019\10 Forestry Ridger [1] Mounted - 3 point linkage [2] Working furrow width 70 cm [3] Working depth 5 - 30 cm [4] Designed to over-ride tree stumps L007 0019\11 Disc Harrow [1] Towed
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 86 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Manual adjustment [3] 3 to 4 m width L007 0019\12 Flat Roller [1] Approx 4m working width L007 0019\13 Bowsaw [1] Approx 50cm general purpose blade [2] Triangular steel frame [3] Tensioning handle and knuckle guard L007 0019\14 Bowsaw [1] Approx 90 cm general purpose blade [2] Tensioning handling L007 0019\15 Chainsaw [1] Used for harvesting and timber
processing
[2] Includes guide bar cover for 40cm bar [3] Approx 2.5.kw [4] Hand guard [5] Automatic chain brake [6] Chain catcher [7] Guide bar approx 40 cm [8] Cutter chain L007 0019\16 Winch [1] Hand operated [2] Approx 800kg lift capacity/1200kg pull
capacity
[3] Includes wire rope for winch / 20m length L007 0019\17 Fertiliser Distributor [1] Mounted, PTO driven [2] Capacity control approx 5001 [3] Spreading width at least 15 m L007 0019\18 Knapsack Sprayer [1] Manual operation [2] Capacity at least 151 [3] Spraying lance [4] 2 Sets spare nozzels L007 0019\19 Protective Equipment
For Sprayer Operator [1] One Piece Suit with Hood
[2] Material: High Resistance PVC [3] Cap with Fixed Face Visor [4] Dust Respirators pk 60 [5] To at least EU standards L007 0019\20 Sprinkler Irrigation
Equipment [1] Petrol engine
[2] Pump output for approx. 2ha [3] Pipework and overhead sprinklers for
approx. 2ha
L007 0019\21 Forestry First Aid Kit For 10 Workers
[1] EU approved for forestry use
[2] Contains plasters, bandages, wound dressings, personal protection pack, survival bag, implements, eye wash etc
L007 0019\22 Safety Belt [1] Tree climbing harness [2] Shoulder straps, padded waist belt and
seat strap
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 87 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Adjustable leg loops L007 0019\23 Azimuthal Compass [1] Small backsight, large foresight [2] Graduated and accuracy to at least 1/2 [3] Needlecard in low viscosity damping
liquid
[4] Lightweight aluminium housing L007 0019\26 Sweeping Net [1] For collecting insects [2] Aluminum frame [3] Stainless steel folding arms [4] Approx 50cm diameter [5] Complete with white bag with reinforced
heading
L007 0019\27 Bignall Pattern Beating Tray
[1] Folding pattern
[2] Tray area approx 110x86cm [3] Frame complete with white bag L007 0019\28 Portable Moth Trap [1] For moth collection [2] 12 volt DC supply [3] 23cm actinic tube [4] Folding flat for transport [5] Complete with rechargeable battery L007 0019\29 Rodent Trap [1] Single door wire mesh design [2] Approx 40 x 12 x 12cm L007 0019\30 Animal Trap [1] Single door wire mesh design [2] Approx 65 x 25 x 30cm L007 0019\31 Binoculars [1] Magnification from approx 7x to 15x [2] Objective lens approx. 35mm L007 0019\32 Soil pH/Nutrient Test Kit [1] Including soil augers, sample boxes [2] pH indiciator with test strips [3] Tests for N, P, K L007 0019\33 Atlas Of Forest Medical
Plants [1] Descriptions with photographs/illustrations of the plants of medicinal value found in forests in Romania
[2] In Romanian language L007 0019\34 Atlas Of Forest Fauna [1] Descriptions with
photographs/illustrations of the fauna found in forests in Romania
[2] In Romanian language L007 0019\35 Water Quality Software
And Hardware Kit [1] Includes software for students to investigate water quality in a range of environments
[2] Temperature, PH and dissolved oxygen sensors
[3] In a carrying case L007 0019\36 Hand Held Survey
Recording And Display Instrument
[1] For topographic measurements
[2] Data entry includes bearings, distances
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 88 of 154
Lot Item Code Item Description Target Specifications Yes No and slopes
[3] Output socket for computer connection [4] Display includes maps and profile views L007 0019\37 Automatic Lightweight
Telescopic Level [1] 24x magnification
[2] Accuracy +/- 2.0mm in 1km [3] Complete with tripod L007 0019\38 Combined Tree Measure [1] To determine cubage [2] Complete with carrying case L007 0019\39 Manual Band
Dendrometer [1] For trees up to 50cm
[2] Range of scope approx 20mm [3] Sensitivity 0.1mm L007 0019\40 Roller Type Digital
Planimeter [1] Maximum working width approx 30cm
[2] Maximum working length approx 30m [3] Computing function L007 0019\41 Compensating Polar
Planimeter [1] For area measurements
[2] Adjustable, to measure up to 27 x 50cm and 10 x 35cm
L007 0019\42 GPS Wireless Receiver [1] 12 channel receiver [2] GPS accuracy <15cm [3] DGPS accuracy <3m [4] Wireless interface to computer L007 0019\43 Weather Recording
System [1] For measuring air pressure, rainfall, wind speed, sun hours and air temperature
[2] Allows connection to internet forecasts [3] Includes computer connection cables and
software
L007 0019\44 Plane Table Compass [1] Dual purpose instrument [2] Large sighting mirror [3] Built in clinometer and spirit level for
accurate horizontal adjustment
[4] Suitable for use on a plane table L007 0019\45 Magnifier, Small [1] Hand magnifier, 3x magnification [2] Round hand magnifier with 75mm glass
lens
[3] Handle and mount L007 0019\46 Magnifier, Medium [1] Hand magnifier 2.5x [2] Round hand magnifier with 90 mm glass
lens
[3] Handle and mount L007 0019\47 Binocular Microscope [1] For determine pest characteristics [2] Interpupillary distance adjustment [3] Dioptric compensation on both eyepiece
tubes
[4] High eyepoint eyepieces, 15x/18mm widefield
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 89 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Quintuple reversed and revolving
nosepiece with click stop
[6] Semi-planachromatic objectives L007 0019\48 Microscope Slide [1] Glass [2] 76x26mm [3] Ground edge [4] 1 to 1,2 mm thick [5] 100 slides /pk L007 0019\49 Albums/Slides/Videos [1] To identify game species, different
hunting guns and ammunition
[2] VHS and/or DVD [3] Referring to Romanian Fauna, in
Romanian language
L007 0019\50 Hunting Guns In Secure Store
[1] Remington 700 SPS Youth or equivalent
[2] With lockable gun case L007 0019\51 Albums On Pest [1] Referring to the Forestry Sector Pests in
Romania
[2] In Romanian language L007 0019\52 Albums On Rocks And
Minerals [1] Referring to the main rocks and minerals in Romania
[2] In Romanian language L007 0019\53 Books For Plant
Identification [1] Referring to the plant species in Romania
[2] In Romanian language L007 0019\54 Books For Insects
Identification [1] Referring to the insects in Romania
[2] In Romanian language L007 0019\55 Radio Voice Receiver [1] LCD Display [2] 8 coded channels [3] 5 km radius [4] 2 handsets L007 0019\56 Ranging Poles [1] 2m in 2 sections [2] Accuracy +/- 2.0 in 1km [3] Complete with tripod L007 0019\58 Safety Helmet Assembly [1] With visor and ear muffs L007 0019\59 Chainsaw User's
Trousers [1] Front protection
[2] Medium, large and extra large sizes per set
L007 0019\60 Chainsaw User's Jacket [1] Medium, large and extra large sizes per set
L007 0019\61 Chainsaw User's Gloves [1] Chainsaw mitts [2] Right hand with seperate index finger [3] Protective material [4] Leather fronts [5] Water repellent nylon backs [6] Leather gauntlet cuff with velcro fastening
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 90 of 154
Lot Item Code Item Description Target Specifications Yes No L007 0019\62 Chainsaw User's Boots [1] Leather L007 0019\63 Brush Cutter [1] Approx. 1.5hp engine [2] Twin handles [3] Equipped with metal and grass cutting
blades
[4] Shoulder strap L007 0019\64 Stump Grubber [1] Combined mattock and axe blades [2] Head approx. 2.3kg [3] Hardwood shaft L008 0013\1 Topographic
Measurement Equipment [1] For: elevation mark transmission, alignment marking, angle measurement and construction surveying
[2] Distance measurement accuracy: +/- 2mm
[3] Minimum reading distance: 1.5 m [4] Maximum reading distance 5000m [5] Servo instrument [6] With accesories: cable supply, wooden
supports, internal NiMh 12 V, 1.8Ah battery, alfa-numeric key-board with internal memory
[7] Software included L008 0013\2 Digital Level [1] Optical and digital level measuring [2] 28x magnification and +/-1.5mm
accuracy approx.
[3] Aperture 36mm [4] Shortest focus 0.6m approx [5] Compensator L008 0013\3 Measuring Tape, Small [1] Blade lock button on case edge, thumb
operation, plastic coated steel blade, power return of blade, zero hook rivetted on end, metric graduations
[2] Length: 5m L008 0013\4 Measuring Tape,
Medium [1] Blade lock button on case edge, thumb operation, plastic coated steel blade, power return of blade, zero hook rivetted on end, metric graduations
[2] Length: 10m L008 0013\5 Measuring Tape, 30m [1] Blade lock button on case edge, thumb
operation, plastic coated steel blade, power return of blade, zero hook rivetted on end, metric graduations
[2] Length: 30m L008 0013\6 Measuring Tools - Steel
Rule [1] Stainless steel
[2] Calibrated in metric units [3] Length: 300mm L008 0013\7 Carpenter's Square [1] Steel [2] Length: 200mm L008 0013\8 Aluminium Levelling
Float, Long [1] Builders levelling float
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 91 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Length: 2.00m [3] Width approx. 100mm [4] Thick walled aluminium extrusion [5] One horizontal and one vertical vial [6] Milled working faces L008 0013\9 Aluminium Levelling
Float, Medium [1] Builders levelling float
[2] Length: 1.50m [3] Width approx. 100mm [4] Thick walled aluminium extrusion [5] One horizontal and one vertical vial [6] Milled working faces L008 0013\10 Aluminium Levelling
Float, Short [1] Builders levelling float
[2] Length: 1.00m [3] Width approx. 100mm [4] Thick walled aluminium extrusion [5] One horizontal and one vertical vial [6] Milled working faces L008 0013\11 Plumb Level [1] Plumb and spirit level [2] Made of aluminium [3] With 600mm tubes L008 0013\12 Aluminium Ladder [1] Height: 2 metres [2] Folding L008 0013\13 Aluminium Scaffold
Tower [1] Aluminium tower system
[2] Maximum height 4 metres [3] Mobile [4] Tubular frame [5] Grill floor sections L008 0013\14 Nail Extractor [1] Manufactured from nickel-chromium steel [2] Hardened jaws [3] High density cushion insulated grips [4] Approximate length: 180 mm L008 0013\15 Nail hammers [1] Set of 2 [2] Weights: 250 and 450g [3] Lengths: 250 and 350mm L008 0013\16 Hammer, Club, Masons [1] Head with two square impact faces,
forged high grade alloy steel
[2] Head faces polished and chamfered [3] Hickory or ash handle, remainder of head
black japanned
[4] Length: 300 to 350mm [3[ Weight: 1800g L008 0013\17 Trowel [1] Gardeners type trowel with stainless steel
blade.
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 92 of 154
Lot Item Code Item Description Target Specifications Yes No L008 0013\18 Ladle [1] For preparing small quantities of material [2] Diameter: 10cm [3] Length: 37cm L008 0013\19 Shovel [1] Flat type for mixing large quantities of
material
[2] Wooden handle L008 0013\20 Plaster And Mortar
Mixer, Electric [1] Built of abrasive resistant steel
[2] Safety guard protection EC standards [3] Handy bag splitter [4] Equipped with power through-out clutch [5] Adjustable rubber mixing blades [6] Extendible pipe tow pole [7] Mounted on a two wheel trailer [8] Drum capacity approx. 85L [9] Powered by electric motor L008 0013\21.
1 Brick Masonry Saw, Electric
[1] Designed for dry or wet-sawing of bricks
[2] Reinforced circular blades [3] Connections for cooling water [4] Blade diameter approx. 360mm [5] Width of cut approx. 540mm [6] Max. Depth of cut approx. 125mm [7] Motor: approx. 3kW L008 0013\21.
2 Stand For Masonry Saw [1] Support frame for masonry saw
L008 0013\21.3
Reinforced Blade [1] Reinforced blades for masonry saw
L008 0013\21.4
Diamond-Tipped Blade [1] Diamond-tipped masonry saw blades
L008 0013\22 Concrete Mixer, Electric [1] Tilting drum concrete mixer [2] 4 detachable mixing blades [3] Forward and reverse rotation [4] Three wheel trailer [5] Under operation supported byleg(s), [6] Drum capacity approx. 175 litres L008 0013\23 Cable Extension Reel [1] Suitable for use with cement mixer and
power saws
[2] For outdoor use [3] On cable drum [4] Floor stand [5] With sockets [6] Cable length approx. 25m L008 0013\24 Rotary Percussion Drill [1] Speed, variable approx. 0 to 2500 rpm [2] Drilling capacity in steel up to 13mm [3] 3-jaw geared chuck and key for drills
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 93 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Locking trigger double pole switch [5] Double insulated [6] Approx. 3-m-rubber covered cable [7] In carrying case L008 0013\25.
1 Flexshaft Vibrator, Electric
[1] Lightweight high frequency vibrator for concrete mixes
[2] Reversible shaft with electric motor; [3] Heads able to be changed [4] Motor approx. 3kW [5] Length of shaft approx. 2.00 m L008 0013\25.
2 Set Accessories And Spare Parts
[1] For use with vibrating tool
L008 0013\26 Drill, Portable, Electric [1] Double insulated, with pistol grip and side handle for left or right position
[2] Continuous variable speed between 0 and 2500 rpm
[3] Complete with chuck, chuck key and approx. 3m rubber covered cable
[4] Drilling capacity in steel: 10mm L008 0013\27 Masonry Drill Set [1] Drill steel with tungsten carbide tipped
bits for percussion
[2] Length approx. 200 mm, diameter 22 mm [3] Length approx. 400 mm, diameter 19 mm L008 0013\28 Sand And Aggregate
Sieves Set [1] Set of sieves in wooden frame approx. 500mm
[2] Galvanized steel wire mesh [3] Mesh sizes 1.0 x 1.0 mm [4] Mesh sizes 1.5 x 1.5 mm [5] Mesh sizes 2.0 x 2.0 mm [6] Mesh sizes 3.0 x 3.0 mm [7] Mesh sizes 5.0 x 5.0 mm [8] Mesh sizes 8.0 x 8.0 mm L008 0013\29 Rod Bender, Diameter,
Small [1] Portable
[2] For bench mounting [3] For bending reinforcing bars [4] Rod diameter 6 - 8 mm L008 0013\30 Rod Bender, Diameter,
Medium [1] Portable
[2] For bench mounting [3] For bending reinforcing bars [4] Rod diameter 10 - 12 mm L008 0013\31 Rod Bender, Diameter
Large [1] Portable
[2] For bench mounting [3] For bending reinforcing bars [4] Rod diameter 14 - 16 mm L008 0013\32 Cutter Bender [1] For cutting and bending reinforcing bars
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 94 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Made of cast iron [3] Mounted on a wood board approx. 1500
x 150mm
[4] Length of handle approx. 1300 mm [5] Rod diameter: up to 18mm L008 0013\33 Hook Type Rod Bender [1] For right and left-hand bending [2] Suitable to handle up to three steel rods
at the same time
[3] One round rod up to 16mm [4] Two round rods up to 11mm [5] Three round rods up to 9mm [6] Length approx. 900mm L008 0013\34 Combination
Bender/loop Former [1] Combined bender and loop forming tool
[2] Adjustable for various steel rods [3] Provided with two bending levers of
approx. 700 and 800mm
[4] Up to three steel rods to be worked at the same time
[5] Max. capacity diameter 16mm [6] Max. capacity for loops 12mm L008 0013\35 Carpenter's Mallet [1] Face dia: 400mm [2] Head length: 50mm L008 0013\36 Marking Gauge [1] Carpenter's marking tool L008 0013\37 Outside Calipers [1] Vernier with thumb lock [2] Range: 0 to 250mm [3] Vernier: 0.02mm readability L008 0013\38 Centre Punch [1] Set of 2 square head [2] 100 mm long [3] 3.2mm point [4] 4.8mm point L008 0013\39 Water Level [1] Consisting of two level tubes [2] Graduated +5 to -5cm with 5mm marks,
sealing caps
L008 0013\40 Glass Cutter [1] Cutter with flow valve system and cutting fluid reservoir
[2] Supplied with standard 134 degree small cutting wheel for oil cutting
L008 0013\41 Short Plane [1] Length: 180mm [2] Blade width: 40mm L008 0013\42 Jack Plane [1] Length: 250mm. [2] Blade width: 40mm L008 0013\43 Smoothing Plane [1] Length: 180mm. [2] Blade width: 40mm L008 0013\44 Horizontal Chisel [1] Plane body made from iron [2] Length: 180 to 200mm L008 0013\45 Mortise Chisel Set [1] Used for manual carving and chiselling
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 95 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Blade widths: 6, 8, 10, 12, 15 mm [3] Dia: 150 to 180mm L008 0013\46 Bussing Chisel Set [1] Used for manual carving and chiselling [2] Length: 150 to 180mm [3] Blade widths: 20, 25, 30 ,40, 60 mm L008 0013\47 Screwdriver Set [1] Insulated vanadium steel blade [2] Four straight slot drivers: 3 x 75mm, 4 x
100, 6 x 125mm and 8 x 150mm, approx.
[3] Two Phillips drivers: N°1 x 75mm and N°2 x 100mm, approx.
[4] Two Posidrive drivers: N°1 x 75 and N°2 x 100mm, approx.
L008 0013\48 Hand Saw [1] For manual rectilinear cutting [2] Blade length: 500mm [3] Blade width: 35 to 40mm L008 0013\49 Carpenter Work Table [1] Steel frame with wooden work surface [2] Tool drawer [3] Length: 2200 x 200 x 750mm L008 0013\50 Bench vice [1] Jaw width: 100mm [2] Anvil back: 70 x 70mm. [3] Cast iron with replaceable steel jaws L008 0013\51 Hand Planer [1] Speed: approx. 15,000 rpm [2] Planing width: maximum 140m [3] Removal depth: maximum 3mm [4] Total length: maximum 450 mm [5] Motor: approx. 1kW L008 0013\52 Planer [1] Cutting width: maximum 310 mm [2] Removal depth: maximum 3mm [3] Planing capacity: 8.5 m/min [4] Speed: 8500 rpm [5] Power: 1.5Kw approx L008 0013\53 Hand Sander [1] Power: maximum 200W [2] Speed: approx. 10,000 rpm L008 0013\54 Dust Collector [1] For collecting dust from power machines [2] Motor power: maximum 2 hp [3] Tube diameter: maximum 200mm [4] Collection capacity: 4 cubic metres L008 0013\55 Hand Circular Saw [1] Power:approx 1500W [2] Speed: maximum 4500 rpm [3] Diameter: approx. 180mm. [4] Complete with 50 assorted discs L008 0013\56 Collapsible Steel
Shuttering [1] For forming reinforced concrete columns
[2] 4pc form panel adjustable for 200 x 200 to 750 x 750, 270 x 90 cross sections or similar
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 96 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Sufficient fixing bolts nuts, adjustable
braces, brackets and bottom plates
L008 0013\57 Wood Sharing For Beam Grinder
[1] For forming reinforced concrete columns
[2] 3.13mp PERI -SPRUCE 21mm 2500 x 1250
[3] 6pc spider zinc plate [4] 6pc crosshead 20-24S, yine plate [5] 6pc vertical post PEP 20N 260 [6] 4pc grinder PERI GT 24-210 [7] 8pc grinder PERI VT- 20K 145 [8] 10pc elbow piece forboard plateau L008 0013\58 Extensible Metal Beams [1] Length: 3m to 5m [2] Width: 200mm [3] Height: 300mm approx. L008 0013\59 Extensible Metal Shore [1] Length max. 2900mm [2] Length min. 1800mm approx L008 0013\60 Formwork, TEGO Type [1] For concrete element forming [2] Sizes 2000 x 600mm [3] Thickness: 8 to15mm L008 0013\61 Transparencies For
Construction/Public Works
[1] Set of transparencies covering equipment, technologies and design features involved with construction
L008 0013\62 Videos/CD For Construction/Public Works
[1] Set of audio-visual media covering equipment, technologies and design features involved with construction
[2] To include sections on protection of labour, fire prevention, health and safety rules, environment protection, emergency resuscitation, material retraining, toxic substances and flammable liquids
L008 0013\63 Safety Equipment [1] Light weight safety helmet [2] Scratch resistant goggles [3] Dust mask [4] Builders general purpose gloves [5] One size overalls [6[ One size quilted coat [6] One size fleece vest [7] Ear defenders [8] One size rainproof coat [9] Safety climbing harness L008 0013\64 First Aid Kit [1] To include: 1 guidance card, 40
individually wrapped plasters, 9 sterile dressings - medium, 3 sterile dressings - large and 6 triangular bandages
[2] Also to include: 4 sterile eye pads, 12 safety pins and 2 pairs of disposable gloves
[3] Wall-mounting box L008 0013\68 Material Samples [1] Set of samples for instruction
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 97 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Ceramic materials [3] Stone materials [4] Marble [5] Wooden floors [6] Bituminous membranes [7] Insulating materials [8] Metallic products [9] Joiner joints [10] Gypsum products L008 0013\69 Burner [1] For heating bituminous membranes for
heat sealing
[2] With gas cylinder and hose [3] Burner tube: 50cm L008 0014\1 Tube Water Level [1] For levelling foundations, concrete work,
long walls etc.
[2] Made of 2 parts, graduated plexiglas [3] Viewers [4] Air venting taps of brass [5] With connecting plastic or rubber pipe [6] Diameter approx. 12mm [7] Length approx. 12m L008 0014\2 Ladle [1] Metallic ladle for preparing small
quantities of materials for surface treatments
[2] Capacity: 100ml approx. L008 0014\3 Spatula [1] With 40 to 100 mm blade width [2] Wooden or plastic handle L008 0014\4 Spreader [1] For spreading floor cement [2] Flat type [3] Wooden handle L008 0014\5 Smoother [1] For use in cement florspreading and for
tile adhesive
[2] Made of steel or stainless steel L008 0014\6 Wall Paper Shears [1] Long metallic shears L008 0014\7 Hammer [1] Iron head and wooden handle [2] Weight: 0.5 to 2kg L008 0014\8 Rubber Hammer [1] For fitting ceramic tiles [2] Metal handle with plastic covering [3] Head diameter: 8cm approx. L008 0014\9 Lime Brush [1] Smooth artificial bristlefor dedusting and
priming
L008 0014\10 Plumb Level [1] Plumb and spirit level [2] Made of aluminium [3] With 600mm tubes L008 0014\11 Wire Brush [1] For removing rust [2] With wooden or plastic handle
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 98 of 154
Lot Item Code Item Description Target Specifications Yes No L008 0014\12 Pliers Set [1] Four-piece tool set with tray [2] Needle nose pliers: 55mm jaw width,
175mm long
[3] Combination pliers: 10mm jaw width, 190mm long, 2-position slip-joints
[4] Adjustable joint pliers: 35mm jaw width, 200mm long
[5] Diagonal cutter: bowed-handle style, 25mm jawwidth, 175mm long
L008 0014\13 Metal Plasterer`s Hawk [1] Blade to be of steel construction [2] Minimum dimensions: 280 x 110mm L008 0014\14 Screwdriver Set [1] Insulated vanadium steel blade [2] Four straight slot drivers: 3 x 75mm, 4 x
100, 6 x 125mm and 8 x 150mm, approx.
[3] Two Phillips drivers: N°1 x 75mm and N°2 x 100mm, approx.
[4] Two Posidrive drivers: N°1 x 75 and N°2 x 100mm, approx.
L008 0014\15 Ruler [1] Made of stainless steel, engraved in mm/cm
[2] Length: 5m, blade width: 25 mm L008 0014\16 Aluminium Levelling
Float [1] Heavy duty builders levelling float
[2] Length 3 m [3] Width approx 100 mm [4] Manufactured from thick walled
aluminium extrusion
L008 0014\17 Builder's Level [1] Builders levelling float [2] Length: 1.50m [3] Width approx. 100mm [4] Thick walled aluminium extrusion [5] One horizontal and one vertical vial [6] Milled working faces L008 0014\18 String Painting Roll [1] Roll length: 18 and 25cm [2] Roll diameter 47 and 58cm [3] Including handle [4] Including telescopic handle 2 to 3m L008 0014\19 Sponge Painting Roll [1] Roll length 18 and 25cm [2] Medium porosity sponge L008 0014\20 Wheelbarrow [1] Metallic box [2] Blow-up tyre [3] Capacity 100 litres L008 0014\21 Plastic Grid [1] For making uniform the string painting
and sponge painting material
[2] Minimum dimensions 255 x 275 mm L008 0014\22 Dyer Brush Set [1] For dry coating [2] Natural hair [3] Width 20 to 100mmm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 99 of 154
Lot Item Code Item Description Target Specifications Yes No L008 0014\23 PVC Plasterer`s Hawk [1] Minimum dimensions: 280 x 140mm [2] With rubber plate L008 0014\24 PVC Plasterer's Hawk
With Sponge Packing [1] Minimum dimensions of 280 x 140mm
[2] With sponge plate L008 0014\25 Spark Lighter [1] Suitable for acetylene and propane
butane
[2] Friction type [3] Approx. 25 spare flints for each lighter L008 0014\26 Sponge Roll [1] For dry coating [2] Roll length: 20 cm [3] Fine porosity sponge L008 0014\27 Metal Grid [1] Minimum dimensions 220 x 300mm [2] With hook L008 0014\28 Portable Drilling Machine [1] Used for mixing mortars, epoxy, screeds
and floor coatings
[2] Hand held, electrically powered, with paddle
[3] Capacity: 75 litres [4] With 150 litre bucket [5] Minimum power 700 W L008 0014\29 Tile Cutting Device [1] Electric ceramic tile cutter [2] Variable angle [3[ Steel bar [3] Aluminium frame L008 0014\30 Stone Cutting Machine [1] Designed for dry or wet-sawing of stone
and marble
[2] Reinforced circular blades [3] Connections for cooling water [4] Blade diameter approx. 360mm [5] Width of cut approx. 540mm [6] Max. Depth of cut approx. 125mm [7] Motor: approx. 3kW [8] To include stand [9] Supplied with 10x resin bonded and 10x
diamond tipped brick/masonry saw blades
L008 0014\31 Polishing Machine For Stone And Marble
[1] Wet polisher for stone and marble floors
[2] Minimum power 1400W [3] Minimum disc diameter 230 mm L008 0014\32 Compressed Air Painting
Pump [1] Capacity: 24 litres
[2] Manually operated L008 0014\33 Air Compressor + Paint
Spray Gun [1] Air cooled air compressor, mounted on horizontal receiver with 4 wheels
[2] Min. capacity 80 litres. [3] Max. pressure not less than 10 bar
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 100 of 154
Lot Item Code Item Description Target Specifications Yes No [4] With automatic pressure switch, safety
valve and water draining
[5] With pressure gauge and pressure regulator
[6] Includes air filter, over-load protection device, 10m hose and quick change connectors
[7] Supplied with air gun and accessories L008 0014\34 Double Aluminium
Ladder [1] Height: 2 metres
[2] Folding L008 0014\35 Scaffold Tower [1] Aluminium scaffold tower system [2] Maximum height 4 metres [3] Mobile [4] Tubular frame [5] Grill floor sections L008 0014\36 Safety Equipment [1] Light weight safety helmet [2] Scratch resistant goggles [3] Dust mask [4] Builders general purpose gloves [5] One size overalls [6[ One size quilted coat [6] One size fleece vest [7] Ear defenders [8] One size rainproof coat [9] Safety climbing harness L008 0014\37 Wall Paper Roller [1] Length of the roll 15-18 cm L008 0014\38 Wall Paper Joint
Pressure Roller [1] Length of the roll 4,5 cm
L008 0014\39 Burner [1] With gas cylinder and hose [2] Burner tube of 50 cm L008 0014\40 First Aid Kit [1] To include: 1 guidance card, 40
individually wrapped plasters, 9 sterile dressings - medium, 3 sterile dressings - large and 6 triangular bandages
[2] Also to include: 4 sterile eye pads, 12 safety pins and 2 pairs of disposable gloves
[3] Wall-mounting box L008 0014\41 Transparencies Topics: [1] Chromatic circle [2] Primary and secondary colours [3] Colours combination [4] Chromatic harmony in construction L008 0014\46 Videos/CD For
Construction/Public Works
[1] Set of audio-visual media covering equipment, technologies and design features involved with construction
[2] To include sections on protection of labour, fire prevention, health and safety rules, environment protection, emergency
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 101 of 154
Lot Item Code Item Description Target Specifications Yes No resuscitation, material retraining, toxic substances and flammable liquids
L008 0014\47 Finishing Materials Samples
[1] Set of samples for instruction
[2] Ceramic tiles [3] Stone tiles [4] Marble tiles [5] Plaster profiles [6] Wall paper [7] Plastic floors [8] Bituminous membranes [9] Insulating materials [10] Gypsum products L009 0015\1 Twin Horse Harness [1] Webbing harness [2] Suitable for draught work L009 0015\2 Potato Planter [1] Two bins for tubers [2] Two bins for fertiliser [3] Maximum planting depth 17 cm [4] Distance between rows 65 to 70cm [5] Spacing of tubers 22 to 38cm [6] Working capacity 0.14 to 0.16
hectares/hour
L009 0015\3 Hammer/Beater Mill [1] Mill of overhung beater cross design [2] Cast iron construction [3] 1.5kW motor driving a beater cross at
8000rpm above a curved replaceable screen
[4] Grinding chamber driven by toothed belt L009 0015\4 Battery Fence Kit [1] Triple geared reel complete with post [2] Reel anchor post with 3 insulators [3] 1500m polywire [4] Powered by 12V battery L009 0015\5 Disc Harrow [1] Attachment for tractor MEAG 1002 [2] Heat treated disc blade diameter: approx.
300mm
L009 0015\8 Tractor [1] Engine output at least 70 hp [2] Safety cab to EU standards [3] PTO 540 to 630 rpm [4] 3-point linkage, towbar [5] Loader capacity 1000 kg, bucket and fork
attachments
[6] Gears: 10 forward and 2 reverse [7] Speeds 2.6 to 2.7 Km/h [8] Adjustable wheel width: front approx
1300 - 1900, rear approx 1400 - 2000
L009 0015\9 Pedestrian Operated Tractor
[1] For soil preparation in restricted areas
[2] With steering brakes and 3x forward, 2x
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 102 of 154
Lot Item Code Item Description Target Specifications Yes No reverse and travel speed gears
[3] Petrol engine 9hp min. [4] Dead man safety cut out [5] Wheels 5.00 x 10 agricultural tread [6] Includes: pair spade lug wheels dia.
48cm to 50cm and rotary transport tiller wheel
[7] Reversible plough [8] Rotary cultivator working width at least
60cm
[9] Adjustable ridger, furrow width 10 to 30 cm,
[10] Two wheel trailer L009 0015\10 Sprinkler Irrigation
Equipment [1] Petrol engine
[2] Pump output for approx. 2ha [3] Pipework and overhead sprinklers for
approx. 2ha
L009 0015\11 Ditching Attachment For Tractor
[1] Hydraulic operation, controlled from tractor cab
[2] Bucket approx 1m width L009 0015\12 Hole Drilling Attachment
For Tractor [1] Can be used for making holes for posts, trees and vines
[2] 3-point attachment [3] PTO driven [4] 230, 450 and 600cm augers L009 0015\13 Knapsack Sprayer [1] Manual operation [2] Capacity at least 12 litres [3] 2 sets spare nozzles L009 0015\14 Protective Equipment
For Sprayer Operator [1] One piece suit with hood
[2] Material: high resistance PVC [3] Cap with fixed face visor [4] Dust respirators: pack of 60 [5] To EU standards L009 0015\15 Drip Feed Irrigation
Equipment [1] For use in glasshouse with fruit trees and soft fruits
[2] Area approx. 50 sq. m L009 0015\16 Horse Grooming Kit [1] Brush and curry comb L009 0015\17 Horse Riding Equipment [1] Saddle, stirrups, reins, whip L009 0015\18 Battery Charger [1] Vehicle battery starter / charger [2] 12 and 24 volt charge output: 28 A [3] 12 and 24 volt start output: 230 A [4] fuse protected for polarity and overload [5] Supplied with cables and 5 spare fuses L009 0019\8 Tractor Mounted
Skidding Winch [1] Three point suspension
[2] Capacity approx. 3t
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 103 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Cable capacity 50m length 8 mm
diameter cable
[4] Protective screen and lower protective screen
L009 0019\57 Tractor With Front Loader
[1] Engine output at least 70 hp
[2] Safety cab to EU standards [3] PTO 540 to 630 rpm [4] 3-point linkage, towbar [5] Loader capacity 1000 kg, bucket and fork
attachments
[6] Gears: 10 forward and 2 reverse [7] Speeds 2.6 to 2.7 Km/h [8] Adjustable wheel width: front approx
1300 - 1900, rear approx 1400 - 2000
L010 0016\1 Cheese Vat [1] Capacity: max.10kg [2] Paddle agitator driven by variable speed
drive motor allowing 0 to 60 traverses per minute
[3] Control console for temperature control, pH monitoring and motor speed control
[4] Both temperature and pH can be monitored
[5] Includes cheese making accessories and computer interface
L010 0016\2 Cheese Press [1] Hand operated [2] Stainless steel container [3] Approx 5L capcacity L010 0016\3 Cheese Mould And
Follower [1] 200 mm diameter x 150 mm
[2] To fit cheese press L010 0016\4 Cheese Making
Accessories [1] Curd cutter
[2] Cheese mat [3] 10x cheese cloth - 600 x 600mm L010 0016\5 Wine Press [1] Vertical basket press [2] Double ratchet operation [3] Hardwood basket [4] Basket capacity approx 25L L010 0016\6 Grape Crusher [1] Hand cranked [2] Aluminium rollers/agitator to crush grapes [3] Augur to remove stems [4] Capacity approx 35-40L [5] Complete with chute and stand L010 0016\7 Fermenting Bucket [1] Complete with lid and airlock [2] Approx 40 litre capacity L010 0016\8 Pressure Tank And
Pump [1] Hand pump operated
[2] Filter housing and hoses
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 104 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Completed with 10 sets of three different
grades of filter pads (coarse, medium and sterile)
[4] Capacity: approx. 15 l L010 0016\9 Double Level Corker [1] Hand operation [2] Plastic and metal construction L010 0016\10 Set Kitchen Knives [1] Plain bladed knives approx. 6, 8, 12, 15
and 25cm
[2] Serrated bladed knives approx. 12, 15 and 25cm
[3] Filleting knife approx. 12 cm [4] Heavy knife for jointing meat approx.
15cm
L010 0016\11 Chopping Board Hardwood
[1] Hardwood
[2] Approx 30 x 40cm L010 0016\12 Set Kitchen Utensils [1] Including: ladle, large fork, spatula,
potato masher, large mixing spoon, grater, flour sieve, vegetable strainer, serrated edge scissors, wooden rolling pin
[2] Including: set cook's measuring spoons 5, 10, 20ml
L010 0016\13 Set Baking Tins And Trays
[1] 4 square trays approx 20 x 30cm
[2] 1 roasting tin approx 20 x 30cm [3] 4 shallow round tins approx 20cm
diameter
[4] 4 deep round tins approx 20cm diameter, 10cm deep
[5] 2 trays with spaces for 12 small cakes L010 0016\14 Set Frying Pan And
Saucepans [1] Flat-based frying pan with lid, approx 25cm diameter
[2] Set of three saucepans with lids, approx. 1, 1.5 and 2litres
L010 0016\15 Set Mixing Bowls [1] 2 x 1L capacity [2] 2 x 2L capacity L010 0016\16 Mincer / Chopper
Machine [1] Hand operated
[2] Alternative grinding plates L010 0016\17 Domestic Food
Processor [1] Calibrated liquidiser capacity approx. 1.5L
[2] Processing bowl approx. 3L [3] Multi-speed plus pulse operation [4] Attachments for whisking, slicing, dough
mixing
[5] 700 Watt motor L010 0016\18 Domestic Cooker [1] Electric [2] 4 rings, variable grill [3] Main oven approx. 50L [4] Second oven approx. 25L L010 0016\19 Domestic Refrigerator [1] Refrigerator compartment approx 200L
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 105 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Seperate freezer compartment approx
100L
[3] Electronic temperature control [4] Digital display and temperature warning L010 0016\20 Domestic Balance
Kitchen Scales [1] To weigh up to 2kg
[2] Digital display [3] Graduated in 1g divisions L010 0016\21 Measuring Jug [1] Measuring up to 1.5L [2] Pyrex glass L010 0016\22 Food Storage Boxes [1] Circular [2] Airtight sealing lids [3] Set of 2: approx 1.2 and 4 litres L010 0016\23 Cordless Electric Kettle [1] 1.5 - 2.0 L capacity [2] Water level indicator [3] Automatic cut-off at boiling point and low
level water
L010 0016\24 Filter Coffee Machine [1] Jug capacity at least 1.5L [2] Hot plate with second jug L010 0016\25 Domestic Pressure
Cooker [1] Capacity approx 5L
[2] Variable weight pressure valve [3] Safety pressure valve L010 0016\26 Deep Fat Fryer [1] Capacity: 2 litres of oil and 1 litre of food [2] Basket with fold-away handle [3] Electronic timer and temperature control [4] Stainless steel construction with lid L010 0016\27 Toaster [1] Capacity 4 slices [2] Automatic pop-up L010 0016\28 Domestic Hand Food
Blender [1] 400 W
[2] Attachments for whisking, chopping and blending
[3] Calibrated beaker [4] Mixer bowl approx 0.6L L010 0016\29 Domestic Electrical
Installation Kit [1] Set of 8x electrician's screwdrivers, 1x wire strippers, 2x pliers, 1x side cutters and 1x circuit voltage tester up to 250V
L010 0016\30 Dining Table [1] 100 x 100cm [2] 850 mm high [3] Frame made of steel pipe, chrome plated
with adjustable leg height
[4] Table top made of wood product and laminated with melamine or formica
L010 0016\31 Dining Chairs [1] Straight backed [2] Wooden frame and seat L010 0016\32 Cutlery Place Settings [1] Stainless steel
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 106 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Each setting to include 1 large and 2
small table knives, 1 large and 1 small table fork, 1 soup and 1 dessert spoon, 1 dessert fork, 1 fish knife and 1 fish fork
L010 0016\33 Cutlery, Serving [1] Stainless steel [2] Set of 3 serving spoons, 1 serving fork, 1
soup ladle
L010 0016\34 Cutlery Tray [1] To accommodate place settings L010 0016\35 Tableware [1] Each settting to include dinner, salad and
side plates, soup and hors d'oeuvre bowls, cup and saucer
L010 0016\36 Table Glassware [1] Set to include glasses for wine, soft drinks, water
L010 0016\37 Table Napkins [1] 30 cm x 30 cm [2] Cotton or damask L010 0016\38 Table Cloth [1] Approx 140 x 140cm L010 0016\39 Serving Tray [1] Approx 45 x 30cm L010 0016\40 Bedroom Furnishing [1] Set of bedroom furniture and furnishings [2] 2x single beds [3] 1x armchair [4] 1x hard chair [5] 1x dressing table with mirror [6] 1x table lamp [7] 1x rug approx. 2m square L010 0016\41 Bedding [1] 1 single duvet, 2 pillows, 1 single bed
blanket, 1 single bed fitted sheet, 1 single bed duvet cover, 2 pillow cases
L010 0016\42 Flower Vases [1] Vases for single flowers and table displays
[2] Florists foam block for table display vase L010 0016\43 Cylinder Vacuum
Cleaner [1] Bagless
[2] Tools forfloors, crevices and upholstery [3] Approx 200W L010 0016\44 Handheld Vacuum
Cleaner [1] Bagless
[2] Battery operated [3] Rechargeable battery and charger [4] Approx 350W L010 0016\45 Handcleaning Equipment [1] Set to include dusters, mops, sweeping
brushes, window cleaners, dustpan and brush
L010 0016\46 Centrifugal Cream Separator
[1] Hand operated
[2] 8L capacity [3] Processing approx 60L per hour at
8000rpm
L010 0016\47 Sausage Filler [1] Hand operated [2] Capacity 7 litres
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 107 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Manual filler with gear reduction drive
and 4 funnels
[4] Stainless steel construction L010 0016\48 Weaving Frame [1] For hand weaving [2] Working area approx. 90 x 150cm L010 0016\49 Electric Sewing Machine [1] Minimum 12 stitch selections [2] Variable stitch selections [3] Four step buttonhole sewing [4] Automatic threading L010 0016\50 Domestic Steam Iron [1] Variable steam control [2] Operating temperature light [3] Aluminium soleplate L010 0016\51 Ironing Board [1] Metal support frame [2] Size: min. 50/140cm [3] Supplied with 2 rayon ironing plates L010 0016\55 Lawn Mower [1] Electric hover mower [2] Blade length at least 35cm [3] Grass collection box L010 0016\56 Casserole Set [1] 0.75, 1.25, and 2 litre casseroles [2] Oven safe L010 0016\57 Cook's Measuring
Spoons [1] Metal
[2] 5, 10, 20ml L010 0027\2 Videomicroscopy
System-video Camera [1] Video camera for connection to trinocular microscope and a video screen
[2] Includes camera and power supply, microscope adapter and video cable
[3] 500 lines colour resolution [4] Lens adapter can be used with reticule
and focusing collar
[5] Requires colour Monitor L010 0027\3 Colour Monitor [1] For use with microscope video camera [2] Displays camera mage via S-Video cable [3] Screen: 19 inch L010 0027\28 First Aid Kit [1] To include: 1 guidance card, 40
individually wrapped plasters, 9 sterile dressings - medium, 3 sterile dressings - large and 6 triangular bandages
[2] Also to include: 4 sterile eye pads, 12 safety pins and 2 pairs of disposable gloves
[3] Wall-mounting box L010 0027\29 Emergency Burn Kit [1] For treatment of minor burns, cuts,
scratches, and abrasions
[2] High impact plastic with wall attachment facility
[3] Includes aerosol bottles of burn relief spray
L010 0027\30 Fire Extinguisher [1] Rechargeable dry chemical extinguisher for ordinary combustibles, flammable
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 108 of 154
Lot Item Code Item Description Target Specifications Yes No liquids,gases, and electrical equipment fires
[2] Responds to A, B, and C fires [3] With monoammonium phosphate to
inhibit reflash electrical fires
[4] Heavy duty steel cylinder [5] Temperature range: -30°C to +50°C [6] Capacity: min 5 kg [7] Includes wall-hanging bracket. L010 0027\31 Amylograph [1] For measurement of gelatinisation
properties and enzyme activity of flour
[2] To ISO 7973 standard [3] Heating rate: 1.5°C/min. [4] Allows results to be stored on PC (not
included)
L010 0027\32 Software for Amylograph [1] Software for amylograph L010 0027\33 Farinograph [1] Torque rheometer with dynamometer for
physical tests on flour and dough.
[2] Two-speed switchable from 63 to 126 rpm
[3] Scale 0-1000 F.U. linear [4] Zero point adjustment : Steplessly
adjustable
[5] Accuracy : Better than +/-1% of full scale [6] Built-in mechanical continuous-line
recorder (paper speed 10 mm/min) and safety device for the mixer measuring head ;
[7] Timer : 1 - 60 min. adjustable [8] Various type of measuring heads can be
mounted to the basic test machine.
[9] Circulation Thermostat with built-in cooling coil (water connection) and tempering coil
[10] Temperature range variable : +20 to +200°C
[11] Temperature regulation proportional L010 0027\34 Measuring Head, Large [1] For tests on small wheat flour samples [2] Calibrated, with removable sigma blades
& stainless steel casting.
[3] Mixer-bowl volume: 300 g [4] Liquid temperature control, [5] Angle thermometer, 0 to 50°C L010 0027\36 Printer And Software for
Farinograph [1] Software for farinograph
[2] Laser printer L010 0027\37 Fermentograph [1] For determination and automatic
registration of the gassing power of doughs with direct recording of the quantity of CO2 developed
[2] Measures the influence of dough improvers in cases of enzyme deficiency or the study of the influences of changes in
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 109 of 154
Lot Item Code Item Description Target Specifications Yes No dough formulae
[3] Can be carried out simultaneously and independently of each other
[4] Frame with stainless steel water bath, with balance and recording systems
[5] Temperature control by contact thermometer
L010 0027\38 Viscograph [1] Steplessly adjustable speed range 10-150 rpm approx.
[2] For measuring and recording the viscosity or gelatinization behaviour of starch
[3] Built-in recorder [4] With exchangeable measuring cartridge
and temperature detector
[5] Possibility for adjusting starting and end temperature, holding time, speed
[6] Heating & cooling rates are variable from 0.5 to 3.0°C/min.
[7] Temperature range : 0-150°C L010 0027\39 Maturograph [1] Twin instrument for measuring and
recording the proving properties of doughs
[2] Two dough containers with pressing stamps
[3] With balance & recording systems [4] With dough pressing device L010 0027\41 Glutograph [1] For testing the quality of dry and wet
gluten
[2] With gluten washer unit [3] Supplies with three rolls of graph paper,
three fibre pens
L010 0027\42 Autoclave [1] Chamber capacity: approx 20 litres [2] Sterilization temperature range: 105 to
120°C approx.
[3] Maximum allowable pressure: 0.14 MPa [4] Agar dissolution temperature range: 60 to
100°C
[5] Chamber material: stainless steel [6] Sterilization timer: 1 to 250 minutes [7] Auto start timer: 1 minute to 7 days [8] Safety functions to include inter-lock
mechanism, over-pressure and over-temperature power cut-off, electric leakage breaker, over current detector, sterilizing time counting timer
[9] Supplied with stainless steel wire mesh basket, bottom plate, drain hose, exhaust bottle and set of caster stoppers
L010 0027\43 Vegetable And Fruit Hardness Tester
[1] LCD 5 digits
[2] Measure capacity: 20kg [3] Min. display: 0.01kg [4] Overload capacity: max. 30 kg
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 110 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Operating temperature: 0°C to 50°C L011 0020\1 Tables [1] 100 x 100cm [2] 850 mm high [3] Frame made of steel pipe, chrome plated
with adjustable leg height
[4] Table top made of wood product and laminated with melamine or formica
L011 0020\2 Chairs [1] Frame made of steel pipe, chrome plated with high backrest and stackable
[2] Seat and backrest upholstered with strong and durable material.
[3] Dimensions: seat 440 x 585 mm, backrest 970 mm. (from floor) approx.
L011 0020\3 Standard Gueridon Trolley
[1] Solid wood, 20 mm thick, 2 shelves, 4 wheels
[2] Dimensions: 80 x 50 x 75cm approx. L011 0020\4 Open Sideboard/Dumb
Waiter [1] Dimesions: 45 x 65 x 20cm approx.
[2] 32mm solid wood L011 0020\5 Waiters Trolley [1] Mobile dumb waiter which can be used
as a trolley
[2] Removable cutlery tray for use as a clearing trolley
[3] Three tiers [4] All shelves to have retaining walls [5] Approx dimensions: 968 x 810 x 410mm L011 0020\6.1 Table Knives, Large [1] Round tip, solid handle, total length
250mm approx. .
L011 0020\6.2 Table Knives, Small [1] Round tip, solid handle, total length 200mm approx.
L011 0020\6.3 Fish Knives [1] Pointed tip, solid handle, total length 225 mm approx.
L011 0020\6.4 Table Forks, Large [1] 3 prongs, total length 200mm approx L011 0020\6.5 Table Forks, Small [1] 3 prongs, total length 180 mm approx L011 0020\6.6 Fish Forks [1] 3 prongs, total length 185 mm approx. L011 0020\6.7 Dessert Forks & Knives [1] Fork: 3 prongs, total length 150 mm
approx.
[2] Knives: total length 200 mm approx L011 0020\6.8 Soup Spoons [1] Total length 200 mm approx. L011 0020\6.9 Consomme Spoons [1] Total length 175 mm approx. L011 0020\6.1
0 Dessert Spoons [1] Total length 140 mm approx.
L011 0020\6.11
Coffee Spoons [1] Total length 110 mm approx;
L011 0020\7.1 Oyster Knife With Handguard
[1] Stainless steel
[2] With handguard [3] Approx 175mm long L011 0020\7.2 Oyster Fork [1] Stainless steel
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 111 of 154
Lot Item Code Item Description Target Specifications Yes No [2] 2 or 3 prongs, total length 150mm
approx.
L011 0020\7.3 Spaghetti Tong [1] Stainless steel [2] Approximate length: 200mm L011 0020\7.4 Asparagus Tong, Simple [1] Stainless steel, single piece [2] Approximate length: 125mm L011 0020\7.5 Asparagus Tong,
Locking [1] Stainless steel
[2] Approximate length, 200mm [3] With locking device L011 0020\7.6 Crab Fork [1] Stainless steel [2] Approximate length: 200mm L011 0020\7.7 Crab Tong [1] Stainless steel [2] Approximate length: 200mm L011 0020\7.8 Snail Fork [1] Stainless steel [2] Approximate length: 125mm L011 0020\7.9 Snail Tong [1] Stainless steel [2] Approximate length: 150mm L011 0020\7.1
0 Fruit Fork [1] Stainless steel
[2] 3 prongs [3] Approximate length: 180mm L011 0020\7.1
1 Fruit Knife [1] Stainless steel
[2] Approximate length: 100mm L011 0020\7.1
2 Butter Knife [1] Stainless steel 18/10
[2] Round tip, hollow handle, total length 175 mm approx.
L011 0020\7.13
Cake Blade [1] Stainless steel, triangular slice
[2] Approximate length:175mm L011 0020\7.1
4 Lemonade Spoon [1] Stainless steel 18/10
[2] Approximate length: 225mm L011 0020\7.1
5 Lobster Cracker [1] Stainless steel 18/10
[2] Approximate length: 200mm L011 0020\7.1
6 Lobster Pick [1] Stainless steel 18/10
[2] Approximate length: 200mm L011 0020\8.1 Support Plates [1] White porcelain, chip resistant [2] 28cm L011 0020\8.2 Dinner Plates [1] White porcelain, chip resistant [2] 26cm L011 0020\8.3 Hors D'oeuvre Plates [1] White porcelain, chip resistant [2] 20cm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 112 of 154
Lot Item Code Item Description Target Specifications Yes No L011 0020\8.4 Dessert Plates [1] White porcelain, chip resistant [2] 16cm L011 0020\8.5 Bottom/Soup Plates [1] White porcelain, chip resistant [2] Diameter: 21.50cm L011 0020\8.6 Bread Plates [1] White porcelain, chip resistant [2] Diameter: 16cm approx. L011 0020\8.7 Broil Tray [1] Stainless steel [2] Oval [3] 40 x 26cm L011 0020\8.8 Bowls Small [1] White porcelain, chip resistant [2] 12cm L011 0020\8.9 Bowls Large [1] White porcelain, chip resistant [2] 16cm L011 0020\8.1
0 Saucers With Leg [1] Stainless steel
[2] With leg [3] 17 x 8 x 9cm approx. L011 0020\8.1
1 Soup Tureen With Lid [1] Bowl form
[2] Stainless steel [3] Two ears [4] 25cm, 3 litres L011 0020\8.1
2 Soup Ladle [1] Stainless steel
[2] 125 ml L011 0020\8.1
3 Soup Cups [1] Stainless steel
[2] 1 ear [3] 25 cl L011 0020\8.1
4 Snail Plate with 6 holes [1] White porcelain, chip resistant
[2] Snail plate with 6 recesses [3] Diameter approx. 18cm L011 0020\8.1
5 Snail Plate with 12 holes [1] White porcelain, chip resistant
[2] Snail plate with 12 recesses [3] Diameter approx. 28cm L011 0020\8.1
6 Oyster Plate [1] White porcelain, chip resistant
[2] Oyster plate with 6 recesses [3] Diameter approx. 26cm L011 0020\9.1 Champagne [1] Glass with stem [2] Capacity: between 125 & 200ml L011 0020\9.2 Red Wine [1] Glass with stem [2] Capacity between 125 & 150ml L011 0020\9.3 White Wine [1] Glass with stem
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 113 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Capacity between 100 and 125ml L011 0020\9.4 Water [1] Glass with stem [2] Capacity between 200 and 250ml L011 0020\9.5 Cocktail [1] Glass with stem [2] Capacity: between 150 and 250ml L011 0020\9.6 Whisky [1] Glass [2] Cylinder form [3] Capacity 28cl L011 0020\9.7 Digestif Glass [1] Glass with stem [2] Capacity between 50 and 100ml L011 0020\9.8 Liqeur [1] Glass with stem [2] Capacity 60ml L011 0020\9.9 Fruit Salad Cups [1] Glass stem [2] Diameter: 12 to 15cm L011 0020\9.1
0 Beer Glass [1] Glass with stem
[2] Capacity 37cl L011 0020\9.1
1 Tumbler [1] Glass
[2] Cylinder form [3] Capacities 25, 50, 100, 150, 200, 250ml L011 0020\10 Thermos-bottle [1] For storage and coffee serving [2] Capacity: 2 litres approx. [3] With pump [4] Stainless steel core L011 0020\11 Filter Coffee Maker [1] Quick filtering dispenser [2] 2 jug with warming plate above and
below
L011 0020\12 Kettles, Copper [1] 1.5 to 2.0 litre capacity [2] Copper [3] With wood handle L011 0020\13 Kettles, Electric [1] 1.5 to 2.0 litre capacity [2] Water-level indicator [3] Automatic cut-off at boiling point and low
level water
L011 0020\14 Table Burner [1] Table top burner [2] For keeping prepared food warm,
preparing flambe dishes and for boiling Turkish coffee
[3] Stainproof construction [4] Adjustable butane flame [5] With integral stand to support 30cm
cookware or coffee pot
L011 0020\15 Commercial Food Mixer - Planetary 4.8 Litre
[1] Planetary action
[2] All metal construction [3] 325 Watt direct drive motor
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 114 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Dough hook,flat beater and wire whip [5] 4.8 litre stainless steel bowl and plastic
cover
L011 0020\16 Commercial Food Processor
[1] Variable speed drive
[2] Pulse and continuous operation [3] Polycarbonate work bowl; approx.
capacity 5 litres
[4] Stainless steel food processing discs [5] Stainless steel cutting and mixing blades [6] Dynamic breaking system [7] Includes food funnel and food pusher L011 0020\17 Stick Blender [1] For preparation of raw materials [2] Adjustable speed [3] To include: stainless amalgamator, small
crusher and 600ml mixer bowl with lid
L011 0020\18 Grill [1] Bench top 6kW electric grill to accommodate grill tray or container
[2] Heat source positioned above the food with device to vary the distance to the food
[3] Two independently controlled elements on the cooking chamber ceiling
[4] With chromed steel cooking grid with anti-tilt runners and heat resistant plastic handles
[5] With 4 litre fat collecting container positioned outside the cooking chamber
[6] Approximate dimensions: 800 x 450 x 450mm
L011 0020\19 Pizza Oven [1] Electric, 6kW, with two baking chambers [2] Stainless steel exterior, mineral material
chamber base and flapdoor with window
[3] Temperature adjustment for oven base and top
[4] Capacity: 3 pizza/chamber [5] Approx. interior measurement: 65 x 95 x
15cm
L011 0020\20 Electric Griddle [1] Non-stick cooking surface [2] Edges cool to the touch [3] Fully immersible cooking surface [4] Grease channel and slide-out drip tray [5] Adjustable temperature control [6] Dimensions: approx. 700 x 350 x 125mm L011 0020\21 Microwave Oven [1] Microwave oven with rotating dish and
splashguard
[2] Cooking system selection by switch [3] Automatic timer and automatic cooking
system
[4] With warming and defrosting programme L011 0020\22 Electric Range Cooker [1] Approximate overall dimensions: 800 x
900 x 250mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 115 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Range with two surfaces, one grooved,
one smooth
[3] Approximate power: 10kW 3-phase L011 0020\23 Stainless Steel Work
Tables [1] Stainless steel preparation table
[2] 860 x 1900 x 700mm L011 0020\24 Large Capacity
Refrigerator [1] Approximate capacity: 125 litres
[2] Automatic defrosting [3] Reversible door [4] Interior light [5] Door storage for large bottles [6] Adjustable thermostat L011 0020\25 Double Electric Pancake
Maker [1] 400mm diameter cast iron griddle plate
[2] Stainless steel finish. [3] Welded and polished corners. [4] Electric L011 0020\26 Automatic Dishwasher [1] All stainless steel construction [2] Approximate basket area: 500 x 500mm [3] Wash tank capacity 13 litres, heater
2.5kW
[4] Rinse boiler power: 2.7kW; consumption 2.5 litres per cycle
[5] With detergent and rinse aid injectors [6] To include 3 baskets L011 0020\27 Deep Fat Fryer [1] Capacity: 2 litres of oil and 1 litre of food [2] Basket with fold-away handle [3] Electronic timer and temperature control [4] Stainless steel construction with lid L011 0020\28 Bread Toaster [1] Extra-wide slots [2] Pull-out crumb door [3] Multi-position control and cancel button L011 0020\29 Toasted Sandwich
Maker [1] With grill plates to accept two slices of bread
[2] Adjustable top plate, suitable for melting cheese
[3] Consumption: 2000 W approx. L011 0020\30 Electric Griddle [1] 600mm x 600mm x 415 mm [2] machined steel plate griddle [3] 12mm thick machined steel [4]fully welded plates [5]thermostatically controlled [6] fat collection drawer [7] fat drainage channel [8] 4kw single phase power [9] accessories: splashguard
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 116 of 154
Lot Item Code Item Description Target Specifications Yes No L011 0020\31 Pressure Cooker [1] Stainless steel with handle [2] Manual button [3] Steamer basket, trivet/stand [4] Tempered glass lid with steam hole [5] Approx. capacity 8 litres L011 0020\32 Set Of Food Cutters [1] 1 HP Motor [2] 18" Stainless Steel Bowl [3] One-piece Burnished Aluminum Housing [4] 1725 RPM Knife Rotation [5] Bowl Cover Safety Interlock [6] 20 RPM Bowl Rotation [7] Double Cutlery Grade Stainless Steel
Knives
[8] Pull/Push On/Off Switch [9] 3" Stainless Steel Legs With Rubber Feet [10] 6' Flexible Cord and Plug L011 0020\33 Cake Decorating Set
Including Turntable And Nozzles
[1] Electric turntable with variable speed control
[2] Bi-directional [3] Manual or motor-driven operation [4] Cake decorating tools including: 18x
metal decorating tips (5 round, 4 open star, 1 basketweave, 3 leaf, 3 petal & 2 drop flower) or similar
[5] Also to include: disposable decorating bags, two tip couplers, five icing colours, one 30mm flower nail, 200mm angled spatula and storage tray storage tray
L011 0020\34 Pasta Machine [1] Chromed steel construction [2] 6 thickness settings [3] Includes handle, clamp, detachable
cutters
[4] Able to make spaghetti, noodles, tagliatelle, fettucine, lasagne and ravioli
L011 0020\35 Demonstration Set Of Sieves
[1] Set of 4 circular stainless sieves with handle
[2] 20, 18, 15 and 8mm approximate diameter
L011 0020\36 Slicing Machine [1] Half oblique [2] Carriage stroke: 22.5cm [3] Cutting height 18cm, 22cm cutting
thickness adjustable to 0 to 16mm
L011 0020\39 Fire Extinguisher [1] Rechargeable dry chemical extinguisher for ordinary combustibles, flammable liquids,gases, and electrical equipment fires
[2] Responds to A, B, and C fires [3] With monoammonium phosphate to
inhibit reflash electrical fires
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 117 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Heavy duty steel cylinder [5] Temperature range: -30°C to +50°C [6] Capacity: min 5 kg [7] Includes wall-hanging bracket. L011 0020\40 Fire Blanket [1] Wool or fibreglass in wall-case with wall
mounting hardware
[] Dimensions approx. 180 x 225cm L011 0020\41 First Aid Kit - Blue
Plaster Kit [1] Consist of the following: * 1 x Blue Detectable Plasters (100 assorted) * 5 x Alcohol Free Wipes * 1 x Blue Detectable tape 2.5cm x 5cm * 12 x Finger Stalls - Blue * 10 x Blue Detectable Extension Plasters * 10 x Blue Detectable Fingertip Plasters
L011 0020\42 Food Cutters [1] Stainless steel, assorted shapes and sizes suitable for individual tarts, petit fours
L011 0020\43 Electric Grid Insect Killer [1] Tubes: 2 x 15W [2] Coverage: Up to 70 sq. m. approx [3] Stainless steel construction L011 0020\44 Drinks Mixing Machine -
Electric [1] Produces upto 40 litres per
[2] Refrigeration system [3] Stainless steel construction [4] 3/4 HP compressor L011 0020\45 Marble Pastry Boards [1] Material: natural marble [2] Size 450 x 450 x 20mm [3] Plastic feet to protect tables and
countertops
L012 0021\1 Single Bed [1] Double-deck spring mattress size 107x198x60 cm.
[2] Box spring mattress: with central support system for sharing weight and balancing the whole area, steel rim, fibre sheet on foam rubber cover, with cotton cover sheet
[3] Box spring base with 2 bases [4] Each base with spring coils lying in 6
rows across wooden bars
[5] Upper top covered with fibre sheet and foam rubber sheet, cotton cover sheet
[6] 25mm thick mattress pad with 4 corner rubber band
[7] Synthetic fiber 140g [8] Size 100x200cm approx. L012 0021\2 Free-standing Mirror [1] Approximate dimensions: 1000 x 600 x
3mm thick
[2] Approximate width of frame: 37 to 50mm [3] Backed in plywood L012 0021\3 Armchair [1] Wooden body covered with cotton [2] Cotton can be removed
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 118 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Body upholstered with sponge [4] Dimensions: 575 x 750 x 650 approx. L012 0021\4 Upright Chair [1] Steel frame chair [2] Cushion with synthetic leather cover [3] Revolving with level adjustable [4] Back cushion and armrests [5] With 5 castors L012 0021\5 Set Of Fitted Bed Linen [1] Bed sheet: 100% white cotton, size 185 x
250 cm.
[2] Pillow case: 100% white cotton, size 500 x 750 x 125mm
[3] Blanket cover: 100% white cotton, size 185 x 250 cm.
L012 0021\6 Bedding [1] Blanket: size 185x250 cm, acrylic wool with dark brown in one side and light brown in the other
[2] Two for each bed [3] Bed skirt: linen fabric with colour to match
bed cover, size 100 x 200 x 30cm approx
[4] Pillow, two for each bed, polyester, size 500 x 750mm
[5] Bed cover: heavy linen fabric with pattern, size 185 x 250cm
L012 0021\7 Bedside Cabinet [1] Teak plywood with natural colour coating [2] Dimension: 350 x 400 x 350mm L012 0021\8 Bedside Lamps [1] Shining brass bedside lamp [2] Metal base and fabric shade [3] Power supply: 2 x 40 Watt [4] Height 500 mm. L012 0021\9 Large Rug [1] Minimum size 2m x 2m [2] Carpet fabric L012 0021\11 Vacuum Cleaner [1] Cylinder cleaner with tools [2] Filter bag and filter, airflow: 80 litres/sec [3] Suction : 2400mm [4] Dry capacity: 20 litres min. [5] Cleaning Range: 25m min. L012 0021\12 Hand-held Vacuum [1] Bagless [2] Battery operated [3] Rechargeable battery and charger [4] Approx 350W L012 0021\13 Demonstration Cleaning
Set [1] Set to include dusters, mops, sweeping brushes, window cleaners, dustpan and brush
L012 0021\14 Hotel Cleaning (janitorial) Unit
[1] Mobile service trolley for room cleaning
[2] Includes 50 litre plastic waste bin and storage for cleaning materials
L012 0021\15 First Aid Kit [1] To include: 1 guidance card, 40 individually wrapped plasters, 9 sterile
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 119 of 154
Lot Item Code Item Description Target Specifications Yes No dressings - medium, 3 sterile dressings - large and 6 triangular bandages
[2] Also to include: 4 sterile eye pads, 12 safety pins and 2 pairs of disposable gloves
[3] Wall-mounting box L012 0021\17 Blue Plaster First Aid Kit [1] Consisting of: pack of blue detectable
plasters (100 assorted), 5x alcohol-free wipes, 1x blue tape 2.5cm x 5cm, and 12x blue finger stalls
[2] Also to include: 10x blue extension plasters and 10x blue fingertip plasters
L012 0021\18 Room Safe [1] Room safe box size 490 x 435 x 390mm approx.
[2] Steel body structure [3] With built-in lock [4] Fire resistant for at least 2 hours L012 0021\19 Room Minibar [1] Size: 47 x 51 x 50 cm approx. [2] Capacity 40 L. [3] Freezer compartment [4] Auto defrost [5] Adjustable feet. [6] Magnet door. [7] Silent working. L012 0022\1 Tourist
Reservation/bookings And Client Accounting Workstation
BOOKINGS SOFTWARE
[1] activity desk and tour reseller software [2] cross-platform, networkable, internet
aware
[3] create vouchered and/or referred reservations with or without pre-collected commissions
[4] pre-set activity check in times [5] pre-set locations [6] set commission rates at activity level [7] set transaction type (voucher or referrl) at
vendor level
[8] set non-commisionable items at vendor level
[9] audio log to track changes to reservations
[10] agent commission reporting [11] basic accounting [12] track vendor receivables and payables [13] account management with inbuilt
security features
[14] log in/log out system to allow for unlimited number of sales agents
[15] set required fields for reserevationists
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 120 of 154
Lot Item Code Item Description Target Specifications Yes No [16] integrated email with spell checking [17] creation of form letters with spell
checking, mailing labels and fax cover pages
[18] contract management [19] search on any criteria
WORKSTATION
[20] 2.6 GHz Pentium4 type processor or equivalent minimum
[21] Minimum 512MB of DDR-RAM Memory [22] 1 HDD, 40GB [23] Video controller with 64 MB SDRAM [24]17" TFT Monitor [25] Wake on LAN and PXE facilities [26] 100/1000 Mbps Ethernet Controller [27] DVD-ROM drive [28] CD-ROM drive; CD writer [29] Audio interface [30] Headset with microphone [31] Minimum 3 available PCI slots and
3USB ports
[32] 3.5'' Floppy diskette drive [33] PS/2 optical mouse, keyboard [34] Desktop case [35] Pre-installed windowing
environment, such as XP professional type version or equivalent.
[36] Office package for a windowing environment, professional version with Romanian License
[37] Antivirus software [38] Software for diagnostic tests of the
major computer components
[39] Recovery and restore solution for the operating system and the software utilities PRINTER AND SCANNER
[40] fax, copier, printer and scanner combined
[41] inket printing technology (colour) [42] copying speed 20 ppm (mono) 12 ppm
(colour) minimum
[43] max printing speed 21 ppm (mono) 15 ppm (colour)
[44] max printing resolution 1200 x 1200 dpi mono / 1200 x 1200 dpi colour
[50] card reader L012 0022\2 Touch Screen Computer
Monitor And Software [1] 17" touch screen monitor
[2] Max resolution 1280 x 1024 [3] Digital on screen display
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 121 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Compatibility: PC, 8514/A, Mac II [5] Anti-glare, scratch resistant, capacitative
overlay screen
[6] Resolution 4096 x 4096 [7] Portrait or landscape rotateable screen [8] Interface USB or RS232 (serial) [9] Coms speed 38400 Baud [10] Software compatibility: DOS, Windows
NT, XP
[11] All cables and software included L012 0022\4 Business Drawing And
Charting Software [1] Windows XP compatible
[2] To create diagrams, charts, graphs and illustrations
[3] Includes ready-made templates and specialised symbols for: flowcharts, organisation charts, Gantt charts, data flow diagrams, network diagrams, fishbone diagrams, phase diagrams and quality control charts
[4] With drag and drop facility L012 0022\5 Web Authoring Software [1] For building web sites [2] Includes features for designing,
coding and extending
[3] Enhanced design tools [4] Built in scripting tools [5] Professional coding tools [6] XML support [7] To work with graphics from other
applications
[8] Compatible with Office programmes [9] Publish to File Transfer Protocol (FTP)
and Web Distributed Authoring and Versioning
L012 0022\8 Route Planning Software [1] Windows XP compatible [2] European edition [3] For route planning and plotting of a
course through towns
[4] Calculation of mileage and time [5] To provide detailed directions [6] Offers information on hotels, restaurants
and tourist sights
[8] Point and click facility L012 0022\10 Accounting Software [1] Customer sales ledger [2] Suppliers/purchase ledger [3] Nominal/general ledger [4] Bank/cash book [5] Automated management accounts
including VAT returns
[6] Integrated report writer
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 122 of 154
Lot Item Code Item Description Target Specifications Yes No [7] File import facility [8] Web trading, sales order processing [9] Written in Romanian language and in
accordance with Romanian accounting systems
L012 0022\11 Freestanding Display Unit
[1] Wall unit for news, magazines and brochures
[2] 1000mm wide [3] Plain back panels [4] 500 mm deep base shelf minimum [5] 1 x 2 tier angled display shelf [6] 2 x 1 tier angled magazine display shelf L012 0022\12 Laminating Machine [1] Photo quality [2] Hot roller technology [3] Variable temperature with electonically
controlled heat settings
[4] Cold function [5] 1 hour shut-off [6] Rejector anti-jam facility [7] Exit tray [8] A3 size [9] Pouch thickness 2 x 75 - 2X 125 microns [10] Heat up time - 5 mins [11] Speed (mm/min) 330 mm/min
ACCESSORIES:
[12] 100 gloss pouches x 250 microns x 100 x 76mm (badge)
[13] 200 gloss pouches x 200 microns x A4 size
[14] 200 gloss pouches x 100 microns x A5 size
L012 0022\13 Thermal Binding Machine
[1] Thermal binding style
[2] Maximum paper width A4 [3] Heating up time: 3 mins [4] Binding capacity: 700 sheets [5] Heat cycle starts automatically when
document is loaded
[6] 3 pre-set heat cycles for different spine widths
[7] Adjustable cooling rack [8] Auto shut off [9] Compatible with any commercial thermal
cover
[10] 100 x 1.5mm, 100 x 3mm, 100 x 4mm A4 thermal binding covers.
L012 0022\14 Guillotine [1] Self-sharpening stainless steel blade [2] Safety guard [3] Blade latch
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 123 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Paper guides - A4, A5, A6 [5] Ruler in cm [6] Paper guide [7] Cutting width 300mm [8] Paper sizes A4 L012 0022\16 Office Trimmer [1] Melamine-faced or metal baseboard [2] Guide rail [3] Self-sharpening tungsten steel cutting
wheel
[4] Automatic clampstrip [5] Cutting width 420mm [6] Cut capacity 2 mm [7] Paper size - up to A3 L012 0022\17 Office Shredder [1] Desk side shredder [2] Copes with staples, paperclips and credit
cards
[3] Automatic stop/start control [4] Reverse function for clearing jams [5] Feed width 230mm [6] Shred capacity A4 70gsm - 10 sheets [7] Min 4 mm shred size [8] Min 25 litre waste volume L012 0022\18 Comb Binder [1] Electric binding/bunching style [2] Punch capacity 15 sheets [3] Binding capacity 250 sheets approx. [4] Adjustable edge guide [5] Comb brake function [6] Waste drawer [7] Jam-clearing procedure [8] Includes 300 x 6mm, 500 x 8mm plastic
comb spines for A4 binding.
L012 0022\19 Display Boards [1] Interlocking collapsible mobile panel display system
[2] Minimum 6 panels each 900mm x 600mm
[3] Minimum 2 headpanels 250mm x 600mm [4] Carrying bag [5] Includes materials for fixing materials to
display boards
[6] System capable of expansion with the addition of further panels
L012 0022\20 Display Unit - Mobile Carousel Type
[1] 3-sided rotary literature stand with wheels
[2] 2-piece pole with matching base. [3] Minimum 1.5m high [4] Designed to hold A4 sized literature [5] Convertible to counter or floor standing
unit
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 124 of 154
Lot Item Code Item Description Target Specifications Yes No [6] 24 pockets L012 0022\22 Collapsible Angled Shelf
Display Unit For Use With 19 Above
[1] Anodised aluminium frame
[2] 2 ladders [3] 2 angled shelves [4] 1 top shelf [5] 1 folding back panel [6] 1000mm H x 700mm W [7] Carry bag [8] Colour to match item 11 above L012 0022\23 Brochure Hanging Racks [1] Wall-mountable display rack [2] 15 x 1/3 A4 pockets [3] Plastic coated wire frames L012 0022\24 Four-drawer Filing
Cabinet [1] Suitable for A4 files
[2] Anti-tilt mechanism [3] W 470 x d 590 x H1315 mm [4] Grey [5] Lockable [6] Fully assembled [7] Supplied with 4 sets of 20 suspension
filing racks
L012 0022\25 Lateral Filing Unit [1] Two-door cupboard [2] Steel construction [3] Fitted with lock [4] Fully assembled [5] Dimensions 920 x 450 x 1800 mm
minimum
[6] Supplied with 3 height-adjustable shelves [7] Lateral filing rails [8] 1 x roll-out filing frame - standard
suspension format
[9] Supplied with 100x A4 lateral filing wallets
L012 0022\26 Business Planning Software
[1] Software to support the preparation of a business plan and marketing planning
[2] Windows XP compatible [3] Includes sample business plans and
built-in market researc
[4] Step-by-step financial guidance [5] Legal tools and funding guidance [6] Allows imports from MS Office [7] Allows generation of "what-if" cash flow
scenarios
[8] Includes sample marketing plans and SWOT analysis tool
[9] built-in graphic forecaster
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 125 of 154
Lot Item Code Item Description Target Specifications Yes No [10] Automatic chart generation [11] Allows importsfrom other packages [12] Facility for market demographics
analysis
L012 0022\27 Telephone Training System For 12 Users
[1] 6 pairs of modern telephones
[2] 6 compact tape recorders with counters [3] Tape recorders start automatically when
1st phone is lifted
[4] Stand for each tape recorder [5] Multi-way cable with two distribution
boxes into which telephones can be plugged
[6] Minimum 20 m cable [7] 12 x 5 m phone extension cables [8] Includes lackable cases [9] 1 microphone headset [10] 12 x 90 minute tapes [11] Control console allowing replay of
recorded calls through a built-in loudspeaker, telephones to be matched into pre-designated pairs connected permanently to a single tape recorder, listening to any of the 6 calls with the headset supplied, use of the headset to talk over the phone to any of the other phone users and and the logging of all role-play on an LCD screen
L012 0022\31 Business English [1] Set of CD or audio cassettes [2] Topics include improving grammar
punctuation and writing skills, business english and terminology, emailing and business letter writing
L012 0022\32 Electronic Dictionary And Translator - Romanian/English
[1] English <-> Romanian non-talking Dictionary
[2] Language pair: English<->Romanian and Romanian<->English
[3] Vocabulary: 450,000 words [4] To include common idioms and useful
phrases
[5] To include general words and medical, technical, legal, business terms and slang
[6] New words recording function for dictionary expansion
[7] Instant reverse translation [8] Battery operated L012 0022\35 Retail And Marketing
Simulation Software/games
RETAILING BUSINESS GAME/SIMULATION
[1] Replicates a retail business selling different ranges of products
[2] Allows decision-making on mark-up, purchasing, advertising, staffing and supplier payment
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 126 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Provides for practice in decision making
and business growth
[4] Includes financial fundamentals including break-even
[5] Provides for marketing and advertising decision-making
[6] Encourages team working LAUNCHING A NEW PRODUCT
[7] Provides experience of the product life cycle, pricing strategy and promotional strategy,
[8] includes consideration of profit and cash flow and analysis, diagnosis, team working and decision making MARKET STRATEGY
[9] analyses the financial impact of marketing decisions
[10] includes a simulation model with range of marketing mix decisions
L012 0023\1 Presentation Software [1] XP professional edition, educational version
[2] For prersentation of slides and graphics with animation and added pictures
[3] Provides experience in use of multimedia [4] Provides information related to key works
and phrases
L012 0023\2 Desktop Publishing Package
[1] XP professional edition
[2] For classroom organisation, calendars, schoolprogrammes etc.
[3] Used to create promotional materials, banners, invitations etc.
[4] Possibility of web publishing [5] Compatible with Item 1 L012 0023\3 Web-authoring Software [1] For building web sites [2] Includes features for designing,
coding and extending
[3] Enhanced design tools [4] Built in scripting tools [5] Professional coding tools [6] XML support [7] To work with graphics from other
applications
[8] Compatible with Office programmes [9] Publish to File Transfer Protocol (FTP)
and Web Distributed Authoring and Versioning
L012 0023\4 Dedicated Project Planning Software
[1] For planning and organising project details, schedules and resource management
[2] To communicate project data and help track and analyze project plan
[3] To include customizable libraries and templates
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 127 of 154
Lot Item Code Item Description Target Specifications Yes No [4] With printing facility for presentation-
ready reports and Gantt charts
[5] Compatible with MS Office [6] To have import/export facility L012 0023\5 Charting And Drawing
Software [1] Windows XP compatible
[2] To create diagrams, charts, graphs and illustrations
[3] Includes ready-made templates and specialised symbols for: flowcharts, organisation charts, Gantt charts, data flow diagrams, network diagrams, fishbone diagrams, phase diagrams and quality control charts
[4] With drag and drop facility [5] Compatible with Item 1 L012 0023\6 Computerised
Accounting Package [1] Provides accounting facilities including: ustomer sales ledger, suppliers/purchase ledger, nominal/general ledger, bank/cash book, automated management accounts including VAT returns, integrated report writer
[2] To include file import facility [3] To include products/stock control
package, web trading and sales order processing
[4] Written in Romanian language and in accordance with Romanian accounting systems
[5] Windows operating system L012 0023\7 Stock Control Software [1] To provide stock control accounting
including: customer sales ledger, full stock history, gross weights held for logistical use and picking and stock checking lists available on demand
[2] To analyse: stock valuation, stock day book, stock shortage report and to provide sophisticated stock reports by suppliers and product groups
[3] To allow web trading and sales order processing
[4] To be compatible with items 14 and 16 [5] Windows operating system L012 0023\8 Computerised Payroll
Package [1] Payroll software addressing: employees list, individual payroll, payroll, unemployment statement and budget insurance statement
[2] Compatible with item 13 [3] Windows operating system L012 0023\9 Cash Book System [1] Software to keep track of cash receipts
and payments
[2] To maintain detailed supplier records [3] To offer overall information on business
activity
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 128 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Windows operating system L012 0023\10 Business & Marketing
Simulation Software [1] To replicate a retail business selling different ranges of products
[2] To include facility for decision-making on mark-up, purchasing, advertising, staffing and supplier payment
[3] To provide practice in decision making and business growth
[4] To include financial fundamentals including break-even
[5] Assists with marketing and advertising decision-making
[6] To provide experience of the product life cycle, coverage of pricing strategy and promotional strategy
[7] To include considerations of profit and cash flow
[8] To analyse the financial impact of marketing decisions
[9] With a simulation model using a range of marketing mix decisions to compute outcomes
[10] School licences valid for minimum 2 years
[11] Windows operating system L012 0023\12 Route Planning Software [1] Windows XP compatible [2] European edition [3] Supports route planning and plotting
courses through town and cities
[4] With calculation of mileage and time [5] To include information on hotels,
restaurants and tourist sights
[6] Point and click facility [7] Windows operating system L012 0023\13 Front Office System For
Hotels [1] Customer reservations
[2] Customer check in-check out [3] Cashiering [4] Reporting on room availability and
occupancy rates
[5] Received messages for rooms [6] Allows interface with other modules
including restaurant bookings
[7] Windows operating system L012 0023\14 Language Software [1] Business English (advanced & medium
level )
[2] Business French (advanced & medium level )
[3] English for Tourists (advanced & medium level )
[4] French for Tourists (advanced & medium level )
[5] Windows operating system
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 129 of 154
Lot Item Code Item Description Target Specifications Yes No L012 0023\16 Cash Register [1] General purpose cash control system [2] Indicates items, total, departments and
change
[3] 10 price presettable departments as standard
[4] Electronic clock displays time and date [5] Features audit roll and receipt facility [6] Provides nine types of transaction totals [ L012 0023\17 Flatbed Scanner [1] Media Handling: flat bed, one-pass colour
and monochrome
[2] Optical Resolution: at least 1,200 x 1,200 dpi
[3] Maximum Resolution: at least 1,200 x 2,400 dpi
[4] Scan area: A4 paper size [5] Interface: USB2 with cable [6] With TWAIN Support [7] Provided with software, 35mm slide
adapter and transparency adapter
L012 0023\18 Filing Cabinet [1] A two-row double movable storage cabinet for documents
[2] Four inner row cabinets are stationary, three front row cabinets are movable on wheels/rails
[3] Each cabinet with two sliding doors and three shelves
[4] Two front row cabinets with 3 drawers, other with 3 open boxes, each divided into 10 squares
L012 0023\19 Bar Code Reader [1] Handheld barcode reader [2] CCD solid state sensor [3] Max. scan rate: 270 scans/sec [4] Reading Indicators : Good Read LED,
green spot on the code, adjustable tone beeper
[5] Barcodes : 2/5 family, Code 39, EAN/UPC, ISBN/ISSN, EAN 128, Code 128, ISBT 128, Code 93, Code 11, CODABAR, TELEPEN, PLESSEY, Code MSI, CODABLOCK, Code 16 k, PDF 417, Code 49.
[6] Coiled cable [7] RS232 interface [8] Cradle L012 0023\20 Carousel Display Unit [1] 3-sided rotary literature stand [2] Grey powder coated pole with matching
grey plastic base
[3] Minimum 1.5m high [4] With wheels and 24 pockets [5] Designed to hold A4 sized literature
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 130 of 154
Lot Item Code Item Description Target Specifications Yes No [6] Convertible to either a counter or floor
standing unit
L012 0023\22 Dictation Machine And Equipment (audio)
[1] Compact digital stereo recording
[2] Minimum 32 MB built in flash memory [3] Minimum 10 hour recording time [4] Voice operated recording [5] Record date & time [6] Built-in speaker [7] USB port [8] Microphone jack, earphone jack &
earphones
[9] USB cable and voice editor software L012 0023\23 Lateral Filing Cabinet [1] Approx. dimensions - 1000 x 900 x
475mm
[2] Load capacity maximum 40 kg per drawer
[3] Three drawers [4] Lock-out mechanism L012 0023\24 Suspension Files For
Use With Lateral Unit [1] 240g orange kraft
[2] Reinforced fronts [3] Suspension rods with nylon tips [4] Supplied with 140mm magnifying plastic
tabs and white inserts
[5] Width: 330mm [6] Compatible with item 23 L012 0023\25 Suspension Files For
Use With Horizontal Filing Unit
[1] 240g orange kraft
[2] Nylon tipped runners [3] Steel wire suspension rods [4] Supplied with 290mm magnifying plastic
tabs and white inserts
[5] Linking system through tabs L012 0023\26 Mailroom Sorting
Equipment [1] Wide horizontal shelving sorter
[2] 2500 x 2700mm deep L012 0023\28 Laminating Machine [1] Photo quality [2] Hot roller technology [3] Variable temperature with electonically
controlled heat settings
[4] Cold function [5] 1 hour shut-off [6] Rejector anti-jam facility [7] Exit tray [8] A3 size [9] Pouch thickness 2 x 75 - 2X 125 microns [10] Heat up time - 5 mins
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 131 of 154
Lot Item Code Item Description Target Specifications Yes No [11] Speed (mm/min) 330 mm/min [12] 100 gloss pouches x 250 microns x 100
x 76mm (badge)
[13] 200 gloss pouches x 200 microns x A4 size
[14] 200 gloss pouches x 100 microns x A5 size
L012 0023\29 Binding Machine [1] Used for binding files, portfolios, projects and learning materials
[2] Punches up to 10 sheets of 20lb bond paper
[3] Vertical closing system [4] A4 format [5] 2:1 pitch [6] Twin loop wire, 21 hole [7] 3 sets of 50 spirals L012 0023\30 Shredder Electric [1] Desk side shredder [2] Copes with staples, paperclips and credit
cards
[3] Automatic stop/start control [4] Reverse function for clearing jams [5] Feed width 230mm [6] Shred capacity A4 70g/sm - 10 sheets [7] Min 4 mm shred size [8] Min 25 litre waste volume L012 0023\31 Guillotine [1] Self-sharpening stainless steel blade [2] Safety guard [3] Blade latch [4] Paper guides - A4, A5, A6 [5] Ruler in cm [6] Paper guide [7] Cutting width 300mm [8] Paper sizes A4 L012 0023\32 Office Trimmer [1] Melamine-faced or metal baseboard [2] Guide rail [3] Self-sharpening tungsten steel cutting
wheel
[4] Automatic clampstrip [5] Cutting width 420mm [6] Cut capacity 2 mm [7] Paper size - up to A3 L012 0023\35 Training CDs -
Interviewing Skills [1] CD format
[2] Recruitment and selection interviews [3] Critical success factors for interviewing [4] Planning for conducting interviews [5] Identifying interviewing styles
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 132 of 154
Lot Item Code Item Description Target Specifications Yes No [6] Choosing the best candidate in a
selection interview
L012 0023\36 Training CD - Project Management
[1] CD/dvd format
[2] Defines project management and involvement in project management process.
[3] Identifies the purpose of a project charter [4] Differentiates between project constraints
and assumptions
[5] Includes the four necessary documents when writing a scope statement
[6] Follows the steps necessary for decomposing a project
[7] Follows the steps necessary to create a good WBS
[8] Lists the elements involved with controlling changes to the project scope.
[9] Quality: overview, planning, improvement and control
L012 0023\37 Training CD - Better Meetings
[1] Making meetings more productive
[2] Getting others to see things your way [3] Non-verbal communication [4] Giving and receiving information [5] The constructive route to agreement [6] Constructive and effective participation L012 0023\38 Training CD - Effective
Time Management [1] CD or dvd format
[2] Key strategies for time management [3] Getting the best from your teams L012 0023\39 Point Of Sale Software
System [1] Windows XP compatible
[2] Includes interface with credit card authorisation software
[3] Networkable version [4] Allows for preform invoicing and track
inventory
[5] Allows customer tracking and purchase history
[6] Receives purchase orders [7] Prints barcode labels [8] Maintains supplier records [9] Interfaces with POS hardware L012 0023\40 Marketing Plan Software [1] Includes sample marketing plans and
SWOT analysis tool
[2] To have built-in graphic forecaster [3] Able to generate charts automatically and
import from other packages
[4] Market demographics analysis facility [5] Windows operating system L012 0023\41 Hotel Front Office [1] Windows xp compatible
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 133 of 154
Lot Item Code Item Description Target Specifications Yes No Simulation Materials - Software Package
[2] Allows for simulation of typical day-to-day scenarios in a small hotel
[3] Includes taking reservations, registering guests, customer servicve issues, billing and housekeeping
[4] Windows operating system L012 0023\42 Training Videos -
Employee Performance [1] To provide a background for role play and other activities concerning performance management and appraisals
[2] CD/dvd formats [3] Topics include: the process of providing
feedback, delivering feedback effectively and giving feedback to supervisors
[4] To provide background on employee performance and resolving conflict
[5] Examines main sources of conflict and the harmful and beneficial sides of conflict
[6] Uses, identifies and addresses various conflict resolution methods
[7] Highlights the difference between resolving and managing conflict
[8] Addresses difficult personalities, conflict beteween managers, conflict between employees and within a team
[9] To provide background on managing difficult people
[10] Topics include addressing difficult personality types, identifying communication barriers, understanding the need for monitoring a difficult person, recognizing when to dismiss a difficult person and taking a proactive approach toward managing difficult people
L013 0025\1 Planetary Mixer, Small [1] Table top [2] 20 litres capacity [3] Supplied with stainless steel bowl,
beater, hook, and wire whisk.
[4] Three running speeds L013 0025\2 Planetary Mixer, Medium [1] Floor standing [2] 60 litres capacity [3] Supplied with stainless steel bowl,
beater, hook and wire whisk.
[4] Three running speeds L013 0025\3 Refrigerator [1] Net storage capacity: 170 litres approx. [2] Exterior finish: Stainless steel [3] Interior finish: Aluminium [4] 2 x coated wire shelves with shelf clips [5] Micro-processor control with digital
display
[6] Fan assisted
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 134 of 154
Lot Item Code Item Description Target Specifications Yes No [7] Automatic defrosting L013 0025\4 Air Conditioning System [1] Split type air condition for either floor or
ceiling installation
[2] Cooling capacity not less than 25,000 BTU/Hr
[3] Automatic temperature controlled [4] Condensing Unit: rotary or piston type
compressor using R-22 refrigerant, with overload protection and time delay
[5] Fan Coil Unit: floor or ceiling type evaporator, with adjustable air flow direction and 3-speeds
[6] Room thermostat and speed control of fan installed on wall
L013 0025\5 Pastry Oven [1] Used for baking pastry [2] Two deck electric oven [3] Each deck holds two baking trays,
approx. 750 x 450mm
[4] High crown door openings, fully tiled sole [5] Mounted on mobile stand [6] With display of temperature and baking
time
L013 0025\6 Electric Boiler [1] To provide warm water used in dough making process
[2] Capacity: 25 litres [3] With temperature control and display L013 0025\7 Preparation Table [1] Stainless steel, with underframe and
shelf
[2] Top 1800 x 600mm, box section underframe 30 x 30mm
L013 0025\8 Pastry Roller [1] Bench model [2] Stainless steel safety guards [3] Belt: approx. 500mm x 600mm length [4] Reversible belts and manual thickness
reduction
[5] Roller gap 0.2mm-40mm [6] Plastic coated endless belts L013 0025\9 Dough Divider [1] Divider for square-shaped dough pieces
suitable for bread and baguettes
[2] Capable of dividing a 24kg dough piece into 20 portions
[3] Adjustable compression L013 0025\10 Scales [1] For weighing dough [2] Mechanical, capacity 5kg [3] Stainless steel bowl L013 0025\11 Proving Oven [1] To accommodate 20 baking trays at
75mm spacing
[2] Stainless steel L013 0025\12 Platform Scales [1] Capacity: 50kg x 100g [2] With non-toxic weighing pan
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 135 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Bench standing L013 0025\13 Portioner/dispenser/filler [1] For portioning pastry fillings [2] Laboratory-scale equipment L013 0025\14 Filling Dosing Gun [1] Hand operated for applying measured
doses of cream
[2] Stainless steel [3] 300ml capacity L013 0025\15 Baking Tray [1] Stainless steel [2] 400 x 600mm L013 0025\16 Bakers Oven [1] Used for baking the dough with steam
operation
[2] 3-deck electric oven [3] Each deck accommodates two baking
trays approx. 750 x 450mm
[4] High crown door openings, fully tiled sole [5] Mounted on mobile stand L013 0026\1 Sausage Filling
Machines [1] 2x sausage fillers, I manual, 1 hydraulic
[2] Both constructed from stainless steel [3] Manual filler, capacity 7 litres for gaining
experience with sausage stuffing
[4] Manual filler with gear reduction drive and 4 funnel
[5] Manual filler suitable for bench-mounting [6] Hydraulic filler capacity: 20 litres [7] Hydraulic filler with knee lever operation
with single knob speed control
[8] Hydraulic filler to include removable lid and polycarbonate piston
[9] Hydraulic filler to include pressure gauge and manual portioning device
[10] Supplied with 15, 20 and 30 mm diameter nozzles
L013 0026\2 Bowl Chopper [1] Bowl capacity 22 litres, 3-knife assembly [2] 2-speed knife shaft drive and 2-speed
bowl drive
[3] All stainless steel construction [4] Floor standing construction [5] Supplied with set of six blades,
thermometer, transparent noise/dust cover
[6] Brake mechanism when bown lifted and emergency stop device
L013 0026\3 Meat Mincer [1] To chop meat used in sausage production
[2] Single block mincer head, tray capacity approx. 10kg
[3] European style plate and knife system [4] Stainless steel worm and pan [5] Supplied with set of 6 blades L013 0026\4 Curing Needle Injector [1] 17-spring retractable needles, for bone in
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 136 of 154
Lot Item Code Item Description Target Specifications Yes No or boneless products
[2] Approx. working width 250mm, working height 175mm
[3] Throughput 300kg/hr at 20% injection rate
[4] Stainless steel construction overall, with adjustable conveyor belt advance
[5] 3-phase electricity L013 0026\5 Ice Maker [1] Output not less than 50kg/day [2] Storage capacity not less than 40kg [3] Air condensing unit L013 0026\6 Meat Mixer [1] For mixing ingredients for sausage filler [2] Capacity: 20 litre [3] Bench-mounting [4] Stainless vesseland lid with viewing slots [5] Tilting and nudge feature for emptying
mixture
[6] Motor driven, forward and reverse action L013 0026\7 Steam Smoke House [1] For drying, smoking, baking and cooling
of meat and sausages
[2] Temperature: up to 90°C [3] Capacity: 1 trolley, 750 x 900 x 1450mm,
curing rods: approx 900mm length for up to 70kg of meat/sausage
[4] Smoke generation: saw dust cartridge [5] Switch panel includes relays, fuses,
contactors.
[6] Supplied with: air circulation fan and water outlet
[7] Includes built-in automatic injector cleaning system, cooling machine and stainless steel evaporator and viewing window
L013 0026\8 Refrigerator [1] Net storage capacity: 170 litres [2] Exterior finish: Stainless steel [3] Interior finish: Aluminium [4] 2 x nylon coated wire shelves with shelf
clips
[5] Micro-processor control with digital display
[6] Fan assisted cooling for even temperature distribution within the cabinet
[7] Automatic defrosting L013 0026\11 Ham Mould [1] Stainless steel, screw type clamping
action
[2] Pear-shaped mould, approx. 30 x 20 x 15cm
L013 0026\12 Mobile Vat [1] For transporting meat between working areas
[2] 200 litre, 2mm thick stainless steel vat [3] Fully welded body, with rolled top edges,
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 137 of 154
Lot Item Code Item Description Target Specifications Yes No beaked front and grab handle
[4] Mounted on base with 4 nylon wheels [5] Lift lugs on either side to suit standard
hoists
L013 0026\13 Butcher's Tray [1] For carrying meaat [2] Heavy gauge stainless steel [3] Approximate dmensions: 500 x 375 x
25mm
L013 0026\14 Preparation Table [1] Stainless steel, with underframe and shelf
[2] Top 1800 x 600mm, box section underframe 30 x 30mm
L013 0026\15 Hot Water Boiler [1] Electric boiler to produce hot water for cleaning
[2] Capacity: 500 litres [3] Thermostatically controlled L013 0026\16 Air Conditioning System [1] Split type air condition for either floor or
ceiling installation
[2] Cooling capacity not less than 25,000 BTU/Hr
[3] Automatic temperature controlled [4] Condensing Unit: rotary or piston type
compressor using R-22 refrigerant, with overload protection and time delay
[5] Fan Coil Unit: floor or ceiling type evaporator, with adjustable air flow direction and 3-speeds
[6] Room thermostat and speed control of fan installed on wall
L013 0026\17 Manual Slicer For Bones L013 0026\18 Electric Slicer [1] For slicing meats and meat products [2] Stainless steel finish [3] Knife size: 300mm [4] Variable slice thickness [5] Blade: 250mm diameter L013 0026\19 Student Knives, Set Of 8 [1] Suitable for students in meat butchery L013 0026\20 Refrigerating Room [1] Fitted with shelves suitable for storing
food
[2] Storage temperature: 2 to 4°C [3] Interior constructed from non-toxic
materials
[4] Internal dimensions: 1.5 x 1.0 x 2.1 m minimum
[5] Single lockable door and safety release mechanism
L013 0026\21 Freezer Room [1] Fitted with shelves suitable for storing food
[2] Storage temperature: -18 to -21°C [3] Interior constructed from non-toxic
materials
[4] Internal dimensions: 1.5 x 1.0 x 2.1 m
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 138 of 154
Lot Item Code Item Description Target Specifications Yes No minimum
[5] Single lockable door and safety release mechanism
L013 0026\22 Grinder Knife [1] For use with grinder [2] Diamond-hard cutting edge fused solidly
to drop forged frame
L013 0026\23 Filleting Knife [1] For separating meat from bone [2] Blade: 200 mm approx. L013 0026\24 Grinder [1] Wheel dimension: 180mm approx. [2] 200W motor [3] With rest and eye-guard L013 0026\25 Ice Machines [1] One per technician area. [2] Approximate output od 30 kg of ice in 24
hours
[3] Storage capacity of 10 kg [4] Approximate dimensions: 400 x 500 x
710 mm (L x B x H)
[5] 220 - 240 V power supply L013 0026\26 Metal Mesh Gloves [1] Linked stainless steel rings, individually
welded for strength,
[2] Ambidextrous 5 finger glove [3] No seams [4] Size: large L013 0026\27 Three Compartment Sink [1] For washing components, tools and trays [2] Stainless steel with splash back and
tubular legs
[3] Each compartment approximately 35Omm deep
[4] With rinse basket L013 0026\28 Cold/Hot Tap [1] For use with three compartment sink [2] Hot/cold mixer tap [3] 300 mm spout L013 0026\29 Jacketed Kettle [1] For meats, soups, stews, sauces needed
to be heated
[2] Stainless steel 2/3 jacketed tilting direct steam
[3] Solid 1 piece stainless steel welded constructionw/ reinforced bar rim
[4] Extra heavy, wide pouring lip welded to top rim
[5] Standard self-locking worm gear tilt mechansim
[6] Mounted on stainless steel tubular stand w/flanged adjustable feet
[7] Capacity: 80 gallons [8] Steam pressure between 5 and 25 PSI [9] Requires Steam Trap, Kettle Cover and
Basket Insert
[10] Requires building steam supply L013 0026\30 Steam Trap [1] For use w/ Jacketed Kettle
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 139 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Standard finish L013 0026\31 Kettle Cover [1] For use with Jacketed Kettle L013 0026\32 Coldroom [1] Suitable for food storage and service [2] Nominal storage volume: 7 cubic metres [3] To include a through the wall refrigeration
pack
[4] Minimum 70mm insulation, encapsulated in non-toxic plastic galvanised sheet
[5] To include 3-tier shelving [6] Airtight door with safety release and lock L013 0032\2 Cheese Vat [1] Capacity: max.10kg [2] Paddle agitator driven by variable speed
drive motor allowing 0 to 60 traverses per minute
[3] Control console for temperature control, pH monitoring and motor speed control
[4] Both temperature and pH can be monitored
[5] Includes cheese making accessories and computer interface
L013 0032\3 Cheese Making Accessories
[1] For use with cheese vat
[2] With horizontal and vertical stainless steel curd knives
[3] Also includes stainless steel rectangular cheddar box and stainless steel mould with wooden follower
[4] Supplied with acid testing kit: self zeroing burette, wooden burette stand, N/9 sodium hydroxide, phenolphthalein indicator, 10 cc pipette, dropping bottle, acid bowl and stirring rod
L013 0032\4 Data Logging Accessory [1] For use with cheese vat [2] Software to transfer results to computer L013 0032\5 Steam Smoke Chamber [1] Stainless steel jacketed vessel mounted
on a mobile cabinet with chilled water circulator
[2] Capacity: 20 to 50 kg of cheese [3] Temperature: up to 90°C [4] Microprocessor control of temperature,
humidity
[5] Smoking time: up to 50 minutes [6] Smoke generation: saw dust cartridge [7] Supplied with: air circulation fan and
water outlet
[8] Includes built-in automatic injector cleaning system, cooling machine and stainless steel evaporator and viewing window
L013 0032\6 Butter Churn [1] Churn paddle electrically driven [2] Electric motor and paddle agitator
incorporated in lid of vessel
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 140 of 154
Lot Item Code Item Description Target Specifications Yes No [3] Batch charge of approx. 5 litres of cream
allows production of more than 1 kg of butter
L013 0032\7 Butter Making Accessories
[1] For use with butter churn
[2] Includes: 1 x 4 litre capacity cream setting pan, 1x dairy thermometer, 1x nylon sieve to strain butter particles, 1x scotch hands to work butter in mass after churning and 1x roll butter muslin to remove water
L013 0032\16 Walk-in Cooler [1] Stainless steel, with 5 shelves min. [2] Digital thermometer [3] To include pressure relief vent, light
switch and vapour-proof light fitting
[4] Also includes remote indoor refrigeration system
L013 0032\20 Table [1] Used for food processing applications [2] Stainless steel [3] All welded seams [4] Includes casters, two with brakes [5] Approximate size: 1.8m x 0.8m L013 0032\22 Work Table [1] High-pressure laminate surface [2] All-steel apron and chromed steel legs [3] Approx. area: 1.8 x 0.8m L013 0032\23 Stool [1] For use with work tables [2] Heavy-gauge tubular steel [3] Height: approx. 500 mm [4] Seat diameter: approx. 500 mm L013 0032\24 Fire Extinguisher [1] Rechargeable dry chemical extinguisher
for ordinary combustibles, flammable liquids,gases, and electrical equipment fires
[2] Responds to A, B, and C fires [3] With monoammonium phosphate to
inhibit reflash electrical fires
[4] Heavy duty steel cylinder [5] Temperature range: -30°C to +50°C [6] Capacity: min 5 kg [7] Includes wall-hanging bracket. L013 0032\25 First Aid Kit [1] To include: 1 guidance card, 40
individually wrapped plasters, 9 sterile dressings - medium, 3 sterile dressings - large and 6 triangular bandages
[2] Also to include: 4 sterile eye pads, 12 safety pins and 2 pairs of disposable gloves
[3] Wall-mounting box L013 0032\26 Emergency Burn Kit [1] For on-the-spot soothing treatment of
minor burns, cuts, scratches, and abrasions
[2] Case with screw holes for wall attachment
[3] Includes 2x aerosol bottles of burn relief spray
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 141 of 154
Lot Item Code Item Description Target Specifications Yes No L013 0032\27 Centrifugal Separator [1] Open-type centrifugal milk pump [2] Stainless steel drum for skimming of
liquids (milk/oil)
[3] Separator mounted on sturdy frame [4] Capacity of separator: 25 l [5] Approx. separator drum speed: 0 to 8000
rpm
[6] All parts in contact with product made of food grade stainless steel
[7] Flow rates: milk skimming, 200 l/h; whey skimming, 300 l/h
L013 0032\28 Milk Pasteurising Plant [1] Stainless Steel construction and non-toxic parts in contact with milk
[2] Capacity: approx. 100 litres/hour [3] With constant level tank, capacity 100
litres
[4] With centrifugal milk pump: approx, 1.5kW, 100 l/h, 2.5 bar
[5] With plate heat exchanger [6] Hot water production and circulation unit,
approx. 2500 kcal/h
[7] Ice-cold water production and circulation unit
[8] Hot water mixer [9] Air compressor, approx. 10 bar [10] Electric control panel fitted with 2-pen
electronic recorder,
L013 0032\29 Milk Packaging Machine [1] Output: up to 300 pouches/hour [2] Volume adjustable from 0.5 and 1 litre
capacity approx.
[3] Drop collector device [4] With heat sealer & control unit L013 0032\31 Thermostatic Milk Vat [1] For storage of fermented milk products [2] Capacity: 200 litres [3] Stainless steel [4] With level sensors for automatic pump
start
L013 0032\32 Centrifugal Milk Pump [1] Maximum flow: 6m3/hour [2] Maximum head: 1.1 bar [3] Motor rating: 0.55 kW [4] Stainless steel construction L013 0032\34 Assembly Materials [1] Complete set of connection pipework,
electrical fittings and installation spares and consumables needed to install all equipment in Milk Processing department
L013 0032\35 Milk Can [1] Capacity: 25 litres [2] Stainless steel L013 0033\1 Crusher-stemmer [1] For stemming and cushing grapes [2] Capacity: approx. 50 l [3] Stainless steel
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 142 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Hand cranked [4] Completed with stand and chute L013 0033\2 Fermenting Vat [1] Capacity: 50 l [2] Complete with lid and air lock L013 0033\3 Pressure Tank And
Pump [1] Hand pump operated
[2] Filter housing and hoses [3] Completed with 10 sets of three different
grades of filter pads (coarse, medium and sterile)
[4] Capacity: approx. 15 l L013 0033\4 Hand Press [1] Vertical hardwood basket press [2] Capacity: 30 l approx. [3] Steel pawls to set the ratchet direction L013 0033\5 Oak Barrel [1] Capacity: approx. 50 l [2] Steam cleaned L013 0033\7 Three Compartment Sink [1] For soaking and washing fruit and
vegetables
[2] Stainless steel with splash back and tubular legs
[3] Each compartment approximately 35Omm deep
L013 0033\8 Cold/Hot Tap [1] For use with three compartment sink L013 0033\9 Rinse Basket [1] To use with three compartment sink L013 0033\10 Vegetable Peeler [1] Capacities: potatoes min. 15 kg in 3
minutes or carrots 10 kg in 3 minutes
[2] Includes built-in peel trap and lock-on hopper cover
[3] Disc diameter: min. 100mm L013 0033\11 Cabinet Base For Peeler [1] For use with vegetable peeler [2] Base consists of strainer and legs [3] Closed top construction [4] Strainer has stainless steel front and
rectangular drawer which is removable for cleaning
L013 0033\12 Food Processor [1] Processes up to 5 kg of product per minute
[2] Includes slicer, julienne, dicer, shredder and grater plates
[3] May be used with dicing grid and slicer slades
L013 0033\13 Dicer Grid [1] For use with food processor [2] Sizes include 7, 9, 15 and 19mm approx. L013 0033\14 Slicing Blade [1] For use with food processor [2] Cast aluminum plates with stainless steel
blades
[3] Thicknesses to include: 1.5, 4, 5.5, 9.5 and 14mm approx.
L013 0033\15 Jacketed Kettle [1] Stainless steel 2/3 jacketed tilting direct steam
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 143 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Solid 1 piece stainless steel welded
construction w/ reinforced bar rim
[3] Mounted on stainless steel tubular stand w/flanged adjustable feet
[4] Capacity: approx. 50 l [5] Steam pressure between 5 and 25 PSI [6] Requires Steam Trap, Kettle Cover and
Basket Insert
[7] Requires building steam supply L013 0033\16 Steam Trap [1] For use w/ Jacketed Kettle L013 0033\17 Kettle Cover [1] For use with Jacketed Kettle L013 0033\18 Basket Insert [1] Basket insert for Jacketed Kettle L013 0033\19 Filter Plate Press And
Frame [1] Equipment for filtering liquids, to remove fine particles, colloidal retention up to and including bacterial retention and large yeast sterilization
[2] Used with fruit juices, extracts, sugar syrups, vinegar, water, pickle juice, cider etc.
[3] Includes mobile trolley on which filter, feed pump and pipe work are mounted
[4] Stainless steel drip tray [5] Filtration area: min. 0.225 square metres [6] To include stainless steel inlet pressure
gauge and self priming pump, rated at 600 litres/hour
[7] Filtration plates with different filtration capabilities
L013 0033\20 Filter Pad [1] For use with filter plate press L013 0033\21 Blancher-Cooler [1] For blanching foods for canning [2] Stainless steel construction, [3] Complete with 4 trays, 2 valves, steam
and water lines with cooling water spray nozzle
[4] Filled trays to be placed in blanching compartment and passed to cooling automatically when next tray is inserted
L013 0033\22 Blanching Tray [1] For use in Blancher/Cooler [2] Perforated bottom L013 0033\23 Jet Recirculation Washer [1] An assembly for cleaning components,
jars and cans
[2] Steam regulator and stainless steel steam mixer
[3] Stainless steel drain valve [4] Integral heater L013 0033\24 Line Exhauster [1] For filling and sealing cans [2] Guide rails adjustable for all cans up to
No 10
[3] Perforated steam pipes extend full length of tunnel
[4] Electric motor: 1/3 hp L013 0033\25 Can Sealing Machine [1] Vacuum, vacuum and gas, and
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 144 of 154
Lot Item Code Item Description Target Specifications Yes No atmospheric sealing machine for metal cans
[2] Approximate sealing capacity: 6 cans per minute in vacuum, 4 cans per minute in gas/vacuum, and 10 cans per minute under atmospheric conditions
[3] Can ranges: 10mm to 150mm by 175mm tall
L013 0033\26 Filling Station [1] For liquids and viscous products [2] Bench top single piston model [3] Speed range adjustable from 10 to 30
containers/minute approx.
[4] Min. 10 l capacity hopper [5] All parts in contact with product are
stainless steel
L013 0033\27 Pulper And Refiner [1] Stainless steel hopper inlet and fixed blade rotor
[2] Mechanical rpm counter [3] 2x sets of stainless steel removable trays
200 mm long by 200 mm dia.
[4] Stainless steel discharge [5] Ability to change speed [6] Support stand [7] Maximum capacity:50 kg/hour L013 0033\28 Homogenizer [1] To emulsify fruit juices and to prepare
unfinished products
[2] Capacity: approx. 100 l/h [3] Working pressure: 220 bar [4] Homogenizing head made of stellite [5] Inlet and outlet tanks [6] Minimum level safety indicator L013 0033\29 Sterilization Surge Tank [1] A surge tank suitable for steam heating
sterilization of packaged food products at temperatures over 100°C
[2] Surge tank: stainless steel, 60 litres approx. capacity
[3] To include: pressure gauge, thermometer, safety valve, bottom discharge valve and air breather
L013 0033\30 Piston Batching Machine [1] Should be suitable to fill containers with a quantity of liquid product ranging from 0 to 500cc
[2] Pneumatically controlled batching head [3] Batching cylinder with nozzle [4] Double effect pneumatic cylinder [5] Unidirectional pneumatic regulators [6] Compressed air filter reducer with
pressure gauge
[7] Pedal control operation L013 0033\31 Consistometer [1] For measuring the consistency of pastes,
sauces and concentrates
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 145 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Stainless steel loading and measuring
tank with graduated bottom
[3] Mobile shutter L013 0033\32 Screw Cooking Machine [1] For blanching and raw material
preparation
[2] Stainless steel cylinder with jacket [3] Screw driven 2 to 10 rpm approx. [4] Set of steam injectors, pressure gauge
and thermometer
[5] With water circulation and thermo-regulation system
[6] Capacity, 40 litres approx. L013 0033\33 Knife Grinder [1] Preparation for pressing. [2] Capacity: approx 30 kg/ hour [3] Made of stainless steel L013 0033\34 Single Screw Pump [1] To transfer semi-processed foods [2] Made of stainless steel [3] Pump rating: 10 to 13 l/min approx. [4] Electric gear motor: 150-750 rpm approx. L013 0033\35 Knives Sterilizer [1] Stainless steel [2] Timer: 0 to 120 minutes [3] Knives capacity 15 min. [4] To accept knife blades up to 450mm L014 0028\1 Winder, Rewinder And
Assembly Winder Machine
[1] With 5 heads for production of spun/filament yarn
[2] 2x spindles prepared as winder [3] 2x spindles prepared as rewinder [4] 1x spindle prepared as assembly winder [5] Max. yarn speed 1500 metres per minute [6] Machine size: 3m/1m width L014 0028\2 Knitting Machine, type 1 [1] Manual patterning machine [2] Double metal bed [3] 200 needles on each bed [4] Finesse 6 E [5] Yarn carriers and guide bars [6] Iron stand [7] With one set of needles and needle
retainer bar
L014 0028\3 Knitting Machine, type 2 [1] Manual patterning machine [2] Double metal bed [3] 200 needles on each bed [4] Finesse 8 E [5] Yarn carriers and guide bars [6] Iron stand [7] With one set of needles and needle
retainer bar
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 146 of 154
Lot Item Code Item Description Target Specifications Yes No L014 0028\4 Textile Scissors [1] Industry grade textile scissors [2] Length approximately 200mm L014 0028\5 Thread Cutting Scissors [1] Metal cutting blades [2] Plastic handles L014 0028\6 CAD System For
Projecting Garment [1] To project basic patterns
[2] To project patterns after a model [3] Digitized patterns [4] Facility to make up patterns [5] Includes measurement and checking [6] Edit technological slip for product [7] Define number of layers for cutting [8] Automatic / manual layout of patterns L014 0028\7 Plotter [1] For generating paper patterns used in
garment making
[2] Size 150 cm [3] Automatic advance and feed paper [4] Max. speed 600 mm/s L014 0028\8 Digit Table [1] Foruse with CAD system [2] Size max. 90/120 cm [3] Pointer 16 [4] Resolution 100 pix/inch [5] Fast access zone L014 0029\1 Sewing Machine For
Textiles [1] Single needle, industrial sewing machine
[2] Thread distribution system [3] Rotary hook [4] Self contained lubrication system [5] Minimum stitches per minute: 3000 [6] Needle lift facility [7] Complete with stand, clutch and motor
fully assembled
[8] Stitch length: 5mm max. [9] Supplied with: 100 sewing needles, 1
spare drive belt, 4 spools, 2 shuttles, 1 litre of appropriate oil and 1 rotary hook
L014 0029\2 Textile Sewing Machine Attachments
[1] Set of attachments for sewing machine
[2] An attachment for stitching braiding widths 16 to 19mm
[3] An attachment for fringing and hemming 0.7cm maximum
[4] An attachment for sewing zippers [5] Linear spacing pin L014 0029\3 Zig-zag Sewing Machine [1] Single needle lockstitch zig-zag seamer [2] High speed with drop feed [3] Automated lubrication
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 147 of 154
Lot Item Code Item Description Target Specifications Yes No [4] Sewing speed max 4000 spm [5] Complete with stand, clutch, work lamp
and spare bulbs
[6] Supplied with 40x needles, 1x Rotary hook, 1x lubricating oil can and 1 litre of appropriate oil
[7] Includes: 1x needle plate, 2x shuttles, 4x spools and 1x drive belt
L014 0029\4 Overlock Sewing Machine, Type 1
[1] Single needle
[2] Number of threads: 3 [3] Stitch width: max. 6mm [4] Stitch length: max. 3.8mm [5] Sewing speed: max 7000 [6] Supplied with: 100 sewing needles, 1
drive belt and 2 litres of appropriate lubricating oil
[7] Includes: 2 needle plates, 3 gripping sets devices and 6 knife sets
[8] Complete with stand, clutch and motor L014 0029\5 Overlock Sewing
Machine, Type 2 [1] Double needle
[2] Number of threads: 4 [3] Stitch width: max 7 mm [4] Stitch length: max 4 mm [5] Sewing speed: max 6000 [6] Supplied with: 100 sewing needles, 1
drive belt and 2 litres of appropriate lubricating oil
[7] Includes: 2 needle plates, 3 gripping sets devices and 6 knife sets
[8] Complete with stand, clutch and motor L014 0029\6 Flat Bed Single Needle
Double Chain Stitcher [1] Single needle, lower feed
[2] Number of threads: 2 [3] Stitch length: max. 4 mm [4] Height of presser foot: max. 10mm [5] Sewing speed: max. 7000 spm [6] Supplied with: 50 sewing needles, 1 drive
belt, 1 litre of appropriate lubricating oil and 1 gripping device
[7] Complete with stand, clutch and motor L014 0029\7 Sewing Machine With
Spin-Over Scalloping For Textiles
[1] Double needle
[2] Thread distribution device [3] Table height adjustment [4] Needle liftup: max. 6 mm [5] Sewing speed: max. 4500 [6] Supplied with: 100 sewing needles, 1
drive belt and 1 litre of appropriate
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 148 of 154
Lot Item Code Item Description Target Specifications Yes No lubricating oil
[7] Includes: 4 gripping set devices L014 0029\8 Button Hole Machine For
Textiles [1] Adjustable length of buttonhole: 4 to 30 mm
[2] Deck size: 50 x 110cm approx [3] Automatic needle lift [4] Automatic lubrication [5] Approximate number of stiches: 3600/min [6] Stiches per button hole adjustable from
80 to 225
[7] Supplied with 50 sewing needles, 1 rotary hook, 4 knives, 4 shuttles and 4 spools
[8] Includes: 1 spare drive belt and 1 litre of appropriate lubricating oil
[9] Complete with stand, clutch and motor L014 0029\9 Link Ending Machine [1] Capable of binding loop by loop [2] Fineness 8-10--14E [3] Supplied with: 10 needles type 407KA
with fineness 75-150, 2 grippers and 1 material fixing-fastening device fineness 14E
[4] Complete with stand, clutch and motor [5] With 1 litre of appropriate lubricating oil L014 0029\10 Sewing Machine With
Blind Stitcher [1] Single chain and single needle
[2] Stitch length: max. 9mm [3] Sewing speed: max. 3000 spm [4] Supplied with 50 sewing needles, 1 spare
drive belt, 1 litre of appropriate lubricating oil and 1 gripping device
[5] Complete with stand, clutch and motor L014 0029\11 Button Sewing Machine [1] Chain stitch [2] Single needle [3] Button size 10 to 20mm [4] Thread trimmer [5] Sewing speed: max. 1500 spm [6] Supplied with 50 sewing needles, 1 spare
drive belt, 1 litre of appropriate lubricating oil and 1 gripping device
[7] Complete with stand, clutch and motor L014 0029\12 Steam Pressing Table [1] 2 arms [2] Slave support [3] Spring support for iron [4] Rayon ironing plate [5] Supplied with 2x rayon ironing plate and
1 foot iron
L014 0029\13 Textile Scissors [1] Industry grade textile scissors [2] Length approximately 200mm L014 0029\14 Thread Cutting Scissors [1] Metal cutting blades
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 149 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Plastic handles L014 0029\15 Mobile Cutting Machine
For Textiles [1] Vertical cutting action
[2] Sharpening device [3] Supplied with 2 vertical cutters L014 0029\16 Tailor's Dummy [1] Adjustable from size 40 to 54 [2] Quick setting, adjustable [3] Foam backed nylon covering [4] Metal stand L014 0029\17 Iron [1] Steam iron soleplate [2] Steel [3] Supplied with 2 non-stick sole plates L014 0029\18 Ironing Board [1] Metal support frame [2] Size: min. 50/140cm [3] Supplied with 2 rayon ironing plates L014 0030\1 Sewing Machine For
Leather And Upholstery [1] Cylindrical arm sewing machine
[2] Approximate arm diameter 45mm [3] Approximate arm length 270mm [4] Single needle [5] Standard holder [6] Triple transport [7] Maximum speed 2500[spm] [8] Maximum pitch 6mm [9] Needle size 4, 6 and 9mm [10] Complete with stand, clutch and motor
fully assembled Supplied with
[11] 4 spools [12] 4 shuttles [13] 2 holders [14] 1 drive belts [15] 1 lubricating oil cans [16] 1 litres of appropriate oil [17] 2 needle plates [18] 2 pressing wheels [19] 40 needles of each size [20] Conforms to CE norms L014 0030\2 Footwear Sewing
Machine With Column [1] Single needle
[2] Approximately 3500 oscillations/min [3] Maximum pitch 8mm [4] Needle lift: 7 to 11mm [5] Motor stop [6] With pressing wheels [7] Maximum speed: 2,500 spm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 150 of 154
Lot Item Code Item Description Target Specifications Yes No [8] Approximate travel width: 250mm [9] Approximate travel height: 100mm [10] Dimensions of machine table: max. 600
x 200mm
[11] Complete with stand, clutch and motor [12] Supplied with: 1 drive belt, 1 litre of
appropriate oil, 2 needle plates, 2 pressing wheels and 80 needles
L014 0030\3 Sewing Machine For Morocco Leather Goods
[1] Column machine
[2] 2 needle design [3] Complete with stand, clutch and motor [4] Supplied with: 1 drive belt, 1 lubricating
oil can, 1 litre of appropriate oil, 80 needles and 2 pressing wheels
[5] Conforms to EC standards L014 0030\4 Sewing Machine With
Plain Platform For Leather
[1] Plane platform dimensions: max. 500 x 200mm
[2] Needles 134: 60-70, 80-100, 110-140 [3] Opening inlet of the pressing needle 7 to
9mm
[4] Approx. pressing needle width 250mm, height 100mm
[5] Pitch length 3.5; 4.5; 6mm max. [6] Speed: max. 5000 spm [7] Complete with stand, clutch and motor [8] Supplied with 2 spools, 2 shuttles, 2
holders, 1 drive belt and 1 litre of lubricating oil
[9] Includes: 1 needle plate, 20 needles 60-70, 20 needles 60-100 and 20 needles 110-140
L014 0030\5 Tapering Machine For Flexible Leather Detail
[1] Width approx. 100cm
[2] Depth approx. 50cm [3] Height approx. 120cm [4] Minimum power: 0.5hp [5] Supplied with: 4 bell knives, 1
transporting drum and 1drive belt
L014 0030\6 Sewing Machine With Column For Leather
[1] Post type leather sewing machine
[2] Needle size 90 to 140 [3] 4 to 12 stitches per inch [4] Needle system 134//35 or equivalent [5] Multi-purpose presser foot [6] Foot lift up to 25mm [7] Complete with stand, clutch and motor
fully assembled
[8] Supplied with: 1 drive belt, 1 litre of appropriate oil and 50 needles
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 151 of 154
Lot Item Code Item Description Target Specifications Yes No L014 0030\7 Punching And Stapling
Machine For Leather [1] Thickness adjustment between the rivetting foot and the work surface
[2] Stapling sizes 5 to 10 cm [3] Supplied with set of accessories L014 0030\8 Zig-zag Sewing Machine
For Leather [1] One needle for seaming and stitching of jacket, shoes and leatherwear
[2] Hardened steel machine with tooldrawer and steel support structure
[3] Stitch length 5mm and width 12 mm [4] Max speed: 1,800 spm [5] Adjustable seam length [6] Bed size not less than 400 x 200mm [7] Adjustable straight and zigzag sewing [8] Capacity of material thickness: 1 to 6mm [9] Supplied with: 1 drive belt, 1 lubricating
oil can and 1 litre of appropriate oil
[10] Includes: 2 needle plates, 2 pressing wheels and 40 needles
L014 0030\9 Sewing Machine For Top Stitching With Overlock Attachment For Leather
[1] Deck size max 60 x 120cm
[2] Thread cutting facility [3] Adjustable table height [4] Self contained lubrication system [5] Capable of max 5,000 stiches/min [6] Complete with stand, clutch and motor [7] Supplied with: 60 sewing needles 134R-
8090, 1 drive belt and 1 litre of appropriate lubricating oil
[8] Includes: 1 pressing needle, 2 needle plates, 1 transporter-conveyor pad, 2 gripping devices and 2 knives for thread cutting
L014 0030\10 Die With Bridge And Sled For Leather
[1] For cutting leather shapes from sheet
[2] Fixed bridge: approx. 1500 x 30mm [3] Mobile sled with cutter knives [4] Electrohydraulic operation L014 0031\11 Roller Kiln [1] Suitable for laboratory and small
production runs
[2] Steel structure with refractory bricks and pre-formed ceramic fibre sheets
[3] The test materialmoved along the kiln by ceramic rollers in preheating and firing zones
[4] The heating system comprises Kanthal spiral heating elements supported by easy to replace ceramic tubes
[5] Zones containing heating elements controlled by a self-adjusting potentiometric pyrometer
[6] Roller diameter: 20mm
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 152 of 154
Lot Item Code Item Description Target Specifications Yes No [7] 3x digital temperature
indicators/adjusters
[8] Maximum temperature: 1,340°C [9] Front roller in steel for loading material
and for the collection area at the exit.
[10] Three phase power supply [11] Useful length: 1,500mm [12] Door dimensions: 180 x 40mm [13] Maximum size of test material: 150 x
150 x 20mm
L014 0031\14 Spraying Cabinet [1] For use in clay preparation [2] Continous water curtain at rear of cabinet [3] Approx. internal dimensions 1000mm x
1000mm x 550mm
[4] Washable stainless steel filter and washabler filter bag
L014 0031\15 Spray Gun [1] General ceramic use spray gun [2] Gravity feed L014 0031\16 Fast Mill [1] Capacity: 2 jars [2] Laboratory fast mill with independent
control for each rotating group
[3] Equipped with protection cover, handle and fast closing clamp, sound proofing, safety microswitch
[4] Protection from the rotating parts [5] With 2x 1litre porcelain jar and grinding
media for each jar
[6] Suitable for up to 500g per 1 litre container
L014 0031\17 Ceramic Glazes [1] Set of ten assorted ceramic glazes [2] Total quantity: approx. 4 litres L014 0031\21 Layers Drier [1] Drying rack [2] Fifty mesh trays with cantilever action for
each layer
[3] Trays zinc coated and counter sprung L014 0031\22 Brush Sets [1] Set of ten brushes for ceramics painting L014 0031\23 Claying Shaping Tools [1] Set of six [2] Wooden handle and ground stainless
steel ends
[3] May be resharpened L014 0031\24 Workbench [1] Manufactured in box section steel with
powder coated finish.
[2] 22mm varnished wooden top. [3] Lockable wheels [4] Approx. bench size 200 x 80cm L014 0031\27 Clay Pack [1] Kaolin 5 kg pack [2] BWS Clay [3] Mt500 Clay [4] Dolomite
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 153 of 154
Lot Item Code Item Description Target Specifications Yes No [5] Sodium Feldspar [6] Potassium Feldspar [7] Plastic clay [8] Red Clay - fine [9] Red Clay - big grain [10] White Earth L014 0031\28 Hydraulic Press [1] For producing laboratory samples for the
ceramics industry
[2] Interchangeable mould with hydraulic specimen extraction
[3] Pressing power adjustable to a maximum of 19,000kg.
[4] Pressing piston 150mm diameter [5] Maximum continuous operating pressure:
120 bar
[6] Control board with general switch and pilot light, double hand control for the pressing operation, push button for activating the extractor.
L014 0031\29 Standard Mould [1] Standard mould for hydraulic press [2] 50mm diameter in cemented steel L014 0031\30 Drying Oven 500l [1] Fan assisted oven with single door [2] The exterior constructed from sheet steel
finished in powder coated paint
[3] The interior chamber is made from mild steel coated with aluminium
[4] Fitted with fixed shelf runners and removable chrome plated wire grid shelves
[5] Heated by sheathed elements in the base fan duct
[6] Control system with direct reading thermostat and overheat thermostat
[7] Mains switch with indicator and heating and overheat indicators
[8] Temperature range: Ambient +10°C to 250°C
[9] Approx. chamber dimensions: 110 x 60 x 75cm
[10] Supplied with 5 shelves (9 positions) L014 0031\31 Beam Balance [1] Laboratory/school type [2] Weighing range: 2500g x 0.01g L014 0031\33 Calibration Tool [1] For use with Bullers rings L014 0031\38 Foot Wiping Machine [1] Rotating belt passing through a water
trough
[2] Excess water removed by means of a full-width, fully adjustable roller
[3] With 5 replacement belts L014 0031\40 Pugmill [1] 400kgs / hour throughput [2] 76 mm outlet L014 0031\41 Wall Mounted Clay
Extruder [1] Aluminum construction with 75mm dia body
Romania Phare 2003
Detailed Grids for Technical Specifications
Page 154 of 154
Lot Item Code Item Description Target Specifications Yes No [2] Ratchet operated alloy plunger [3] Supplied with set of 5 standard dies L014 0031\42 Slab Roller [1] Free standing unit [2] Minimum working area: 1000mm x
500mm
[3] To roll clay slabs from 3mm to 32mm thick
L014 0031\43 Blunger [1] Steel tank, 125 litre capacity, with GRP lining
[2] Mixing blades and shaft in stainless steel [3] With stand L014 0031\44 Potter's Wheel [1] Electrically driven potters wheel [2] 250mm wheelhead with splashtray [3] Reversible drive L014 0031\45 Potter's Hand Tool Set [1] To include, loop tool, ribbon tool, wood
potter’s rib, steel needle tool, wood modeling tool, sponge, steel scraper and wire clay cutter.
L014 0031\46 Slip Poring Table [1] Approx. pouring area: 100 x 50cm L014 0031\47 High Speed Glaze Mixer [1] Approx. container capacity: 5 litres [2] With electric mixer