-5- -6-

FCC Information

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) this device may not cause harmful interference;

(2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or

modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the

equipment.

EU Environmental ProtectionWaste electrical products should

not be disposed of with household

waste. Please recycle where

facilities exist. Check with your

local authority or retailer for

recycling advice.

Warnings The apparatus shall not be exposed to dripping or splashing

and that no objects filled with liquids, such as vases, shall

be placed on the apparatus.

Turn off the camera/receiver if the system is not in use.

The camera/receiver can only be completely disconnected

from the mains by unplug the adapter.

Do not cut the DC power cable of the apparatus to fit

with another power source.

Attention should be drawn to the environment aspects

of battery disposal.

Specifications

* Actual transmission range may vary according to weather,

location, interference or building construction.

* All specifications are subject to minor change without prior

notice.

Cam

era

Receiver

General

Item Value

Transmission Frequency

Transmission Power

Unobstructed Effective Range

Modulation Mode

Operating Temperature

Operating Humidity

Imaging Sensor Type

Picture Total Pixels

Minimum Illumination

Night Vision Distance

View Angle

Bandwidth

ISM 2,400 ~ 2,483 MHz

17 3dBm

300m (Max.)

GFSKO O O O

0 C ~ 50 C / 32 F ~ 122 F

15%~85%

CMOS

640 x 480

0Lux (IR ON); 5Lux (IR OFF)

5m (Max.)

3MHz

Spread Spectrum FHSS

Sound Detection Sensitivity

Consumption Current(Max.)

Power Supply

Dimensions(W x D x H)

Weight(About)

LCD Screen Type

Effective Pixels

Receiving Sensitivity

Consumption Current(Max.)

Battery Working Time

<-38dB

500mA

2.36TFT-LCD

480 (R.G.B) x 234

-80dBm

200mA

3 hours

Weight(About) 135 g

Power Supply

Dimensions(W x D x H)

5VDC

68 x 149 x 26 mm

5VDC

112 x 109 x 133mm

420g

O55

Version 1.1Please read this user manual carefully before using this product. Failure to understand operation procedures may result in injury.

Model: 8229JE

DIGITAL PAN-TILT-ZOOM HOME SURVEILLANCE SYSTEM

8. Adjusting Viewing Angle of Camera The direction pad key on the receiver acts as a remote control for the viewing angle of the camera. Usage is as follows: 1). Use the / keys to rotate the camera horizontally. The maximum angle of rotation is 270 degrees. 2). Use the / keys to rotate the camera vertically. The maximum angle of rotation in this direction is 120 degrees.

6. Zooming You can enlarge the picture seen on the receiver by two (2) times by pressing the zoom button once; press again to return to non-zoom mode.

Other Functions * Press the CTRL button once to turn off the LCD screen for sleep mode; press again to turn it back on. While in sleep mode, you will still be able to hear the sounds picked up by the microphone.* Hold the CTRL button for 3 seconds to rotate the image seen on the receiver by 180 degrees. this optional mode is useful for users who have installed their cameras upside down.

* You may connect the receiver to any display device with an A/V input for a larger, clearer picture.

7. Channel Looping Setup The receiver supports up to 4 cameras working at the same time. you could press and hold the ZOOM button on the receiver until appear "scanning...." to enable the automatic looping function. the channels are shown on the monitor/TV one by one every 5 seconds. Press and hold the ZOOM button on the receiver again to exit the looping function. You can also press the CHANNEL button to exit the looping function.

Packing List

Structure

Installation

-1- -2- -3- -4-

Volume Control

Brightness Control

* 8229JE = GD8229 (camera) + GD7615 (receiver)

2.4GHz Wireless Camera x 1

2.4GHz Wireless Receiver x 1

Power Adapter x 2

AV Cable x 1

Earphone x 1

Antenna x 1

Installation Diagram

Rotate Base

Lens

Built-in Microphone

Infrared LEDs

Power Switch

Power Jack

Channel Selector

Channel Sync

Antenna Plug

Channel SyncIndicator

Power Indicator

Camera

Adapter

Camera

Receiver Adapter Monitor/TV

AV Output

VCR

Receiver

3. Connect the provided power adapter to the power jack of the

receiver and an appropriate power source. Then slide the power

switch to the ON position.

1. Attach antenna to the antenna plug at the back of the camera

by screwing it in place. Then place the camera on a flat, stable

surface.

2. Connect the provided power adapter to the power jack and an

appropriate power source. Then slide the power switch to the

ON position. The power indicator will light up and the camera

will calibrate itself by automatically running through its full range

of motion.

Notes:

* This receiver can also work on battery power. Please load four

(4) AAA batteries into their appropriate slots at the back of the

receiver, with proper orientation as indicated on the battery

compartment.

* If the receiver is left unused for an extended period of time,

please disconnect it from the power adapter and remove batteries

if they have been installed.

4. Channel Synchronization

5. You may adjust brightness and volume to your desired level by

rotating the dials on the side of the receiver.

Battery Cover

Stand

Earphone Jack

Power Jack

A/V Output

Volume Indicator(from camera)

Antenna

LCD Screen

CTRL

Zoom

Volume Control

Brightness Control

Channel Button

Camera Lens Direction Pad

Power Switch

Channel Sync Indicator(the second Led )

Press and hold the Channel button on the receiver until the

channel sync indicator flashes, and then press once the Channel

Sync key on back of the camera during the indicator flashes

(about 8 seconds) on the receiver, at which point the channel

number displayed on the receiver should match the channel

selected on the back of the camera. You may now control the

camera with the direction pad on the receiver.