6503u ii 01 eng - panasonic · pdf filetv tuner (cy-tun153u, ... you're ready to begin...

1

2 CQ-VD6503U

Engl

ish

Safety InformationCAUTION:• PLEASE FOLLOW THE LAWS AND REGULATIONS

OF YOUR STATE, PROVINCE OR COUNTRY FORINSTALLATION OF THE UNIT.

• TO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK OR PRODUCT DAMAGE, DO NOT EXPOSETHIS APPLIANCE TO RAIN, SPLASHING, DRIP-PING OR MOISTURE.

The following applies only in the U.S.A.

Part 15 of the FCC RulesFCC Warning:Any unauthorized changes or modifications to thisequipment would void the user's authority to operatethis device.

WARNING• This installation information is designed

for professional installers with knowledgeof automobile electrical safety systemsand is not intended for non-technical, do-it-yourself individuals. It does not containinstructions on the electrical installationand avoidance of potential harm to airbag, anti-theft and ABS braking or othersystems necessary to install this product.Any attempt to install this product in amotor vehicle by anyone other than a pro-fessional installer could cause damage tothe electrical safety system and couldresult in serious personal injury or death.

• If your car is equipped with air bag and/oranti-theft systems, specific proceduresmay be required for connection and dis-connection of the battery to install thisproduct.Before attempting installation of this elec-tronic component against the manufactur-er's recommendation, you must contactyour car dealer or manufacturer to deter-mine the required procedure and strictlyfollow their instructions.FAILURE TO FOLLOW THE PROCEDUREMAY RESULT IN THE UNINTENDEDDEPLOYMENT OF AIR BAGS OR ACTIVA-TION OF THE ANTI-THEFT SYSTEMRESULTING IN DAMAGE TO THE VEHICLEAND PERSONAL INJURY OR DEATH.

• TO REDUCE THE RISK FOR FIRE OR ELEC-TRIC SHOCK AND ANNOYING INTERFER-ENCE, USE ONLY THE INCLUDED COMPO-NENTS.

• This unit operates with a 12 V DC negativeground auto battery system only. Do notattempt to use it any other system.

• Do not expose the unit to the direct sun-light or excessive heat.

2

3CQ-VD6503U

Engl

ish

Upgrade Options

Safety Information................................................2Upgrade Options..................................................3Contents................................................................3Installation Guide.................................................4Electrical Connections ......................................12

Contents

Display UnitCQ-VD6503U

Expansion Module(CY-EM100U, option)

Hands-Free Kit featuringBluetooth® technology(CY-BT100U, option)

XM Satellite Radio receiver(XMD1000)

CD Changer(CX-DP880, option)DVD Changer(CX-DH801U, option)

TV Tuner(CY-TUN153U, option)

Sirius Satellite Radio receiver (SIR-PAN1)

Headrest Monitor(CY-V7100U, option)

iPod®

3

4 CQ-VD6503U

Engl

ish

Installation Guide

WARNING This installation information is designed for professional installers with knowledgeof automobile electrical safety systems and is not intended for non-technical, do-it-yourself individuals. It does not contain instructions on the electrical installation andavoidance of potential harm to air bag, anti-theft and ABS braking or other systemsnecessary to install this product.Any attempt to install this product in a motor vehicle by anyone other than a profes-sional installer could cause damage to the electrical safety system and could resultin serious personal injury or death.

If your car is equipped with air bag and/or anti-theft systems, specific proceduresmay be required for connection and disconnection of the battery to install this product.Before attempting installation of this electronic component against the manufactur-er's recommendation, you must contact your car dealer or manufacturer to deter-mine the required procedure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOY-MENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING INDAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.

OverviewThis product should be installed by a professional.However, should you decide to install the product againstthe manufacturer’s recommendation, these operatingInstructions do not contain electrical installation instruc-tions. You must contact your car dealer or manufacturerfor electrical connection instructions to avoid possibledamage to your electrical safety systems and resultinginjury or death. (Please refer to the “WARNING” state-ment above).Your next step is to decide where to install the unit. Theinstructions in these pages will guide you through theremaining steps:¡Identify and label the car wires.¡Connect the car wires to the wires of the power con-

nector.¡Install the unit.¡Check the operation of the unit.

If you encounter problems, please consult your nearestprofessional installer.

Warning¡This unit operates with a 12 V DC negative ground

auto battery system only. Do not attempt to use itwith any other system. Doing so could cause seri-ous damage.

Before you begin installation, look for the following itemswhich are packed with your unit.

¡Operating Instructions (including “Limited Warranty”and “Customer Service Directory”).

¡Installation Hardware .....Needed for Installation.

4

5CQ-VD6503U

Engl

ish

<YFX994C134ZA>

Lock Cancel Platee 2

Transportation Bracket RemovalBe sure to remove the transportation brackets beforeuse (installation). Use round head screws (5 mmø x 8mm) for installation. (a page 11)Be careful not to lose these screws.

Round Head Screw (5 mmø x 8 mm)

Transportation Bracket

Installation Hardware (For Installation)

Note:¡The number in parenthesis underneath each accessory

part name is the part number for maintenance andservice.

¡Accessories and their parts numbers are subject tomodification without prior notice due to improvements.

¡Mounting Collar w is mounted on the main unit atshipment.

¡Use the supplied screws for installation exclusively. Incase of losing any of them, please order the specificscrew.

Qty.DiagramItemNo.

Trim Plate

<YFC054C088ZA>

q 1

Mounting Collar

<YFX214C437ZA>

w 1

Rear Support Strap

<YEFG044C002>

<ZZBISVD6503>

u 1

Round Head Screw(5 mmø x 8 mm)i 2

Flat-Head Screw(5 mmø x 8 mm)o 6

<ZZBISVD7001A>

Mounting Bolt (5 mmø)r 1

Tapping Screw (5 mmø x 16 mm)t 1

Hex. Nut (5 mmø)y 1

Before Installation

Caution¡Do not press the panel forcefully.¡Do not scratch the panel with fingernails or any hard

objects.¡Do not bump the front panel.a Failure to observe the above may damage or break

the glass on the surface of the touch panel.

Installation Hardware (For Wiring)

Qty.DiagramItemNo.

Power Connector (ISO connector)

<YEAJ012890>

!0 1

Reverse Extension Cord!1 1

Clip Connector!2 1

5

6 CQ-VD6503U

Engl

ish

Installation Guide (continued)

Before InstallationWarning

¡Do not install the monitor in a location whichobstructs driving, visibility or which is prohibitedby applicable laws and regulations. If the monitoris installed in a location which obstructs forwardvisibility or operation of the air bag or other safetyequipment or which interferes with operation of thecar, it may cause an accident.

¡Never use bolts or nuts from the car's safetydevices for installation. If bolts or nuts from thesteering wheel, brakes or other safety devices areused for installation of the monitor, it may cause anaccident.

¡Attach the wires correctly. If the wiring is not cor-rectly performed, it may cause a fire or an accident.In particular, be sure to run and secure the leadwire so that it does not get tangled with a screw orthe moving portion of a seat rail.

¡Use with 12 V DC negative ground car. This unit isonly for use with a 12 V DC negative ground car. Itcannot be used in large trucks or diesel cars whichare 24 V DC cars. If it is used in the wrong type ofcar, it may cause a fire or an accident.

Required ToolsYou’ll need a screwdriver and the following:

12 V DCTest Bulb

ElectricalTape

Side-CutPliers

Caution¡Use the specified fuse. Be sure to always use the

specified fuse. If a fuse other than the specifiedfuse is used, it may cause a fire or an accident.

¡Do not damage the cord by pinching or pulling it.Do not pull or damage the cord. If the cord is nottreated properly, it will short out or be severedand may cause a fire or an accident.

Dashboard Specifications

Identify All LeadsThe first step in installation is to identify all the car wiresyou’ll use when hooking up your LCD monitor.As you identify each wire, we suggest that you label itusing masking tape and a permanent marker. This willhelp avoid confusion when making connections later.

Note:¡Do not connect the power connector to the display

unit until you have made all connections. If thereare no plastic caps on the hooking wires, insulateall exposed leads with electrical tape until you areready to use them. Identify the leads in the follow-ing order.

Power LeadIf your car has a radio or is pre-wired for one:Cut the connector wires one at a time from the plug(leaving the leads as long as possible) so that you canwork with individual leads. Turn the ignition on to theaccessory position, and ground one lead of the test bulbto the chassis.

Touch the other lead of the test bulb to each of theexposed wires from the cut radio connector plug. Touchone wire at a time until you find the outlet that causes thetest bulb to light.

Now turn the ignition off and then on. If the bulb alsoturns off and on, that outlet is the car power lead.

If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio(RADIO) accessory (ACC) or ignition (IGN).

THICKNESSMIN. 4.75 mm 3/16”MAX. 5.56 mm 7/32”

111.6 mm 4 3/8”

182 mm 7 3/16”

6

7CQ-VD6503U

Engl

ish

Battery LeadIf your stereo unit has a yellow lead, you will need tolocate the car's battery lead. Otherwise you may ignorethis procedure. (The yellow battery lead provides contin-uous power to maintain a clock or other functions.)If your car has a radio or is pre-wired for one:With the ignition and headlights off, identify the car bat-tery lead by grounding one lead of the test bulb to thechassis and checking the remaining exposed wires fromthe cut radio connector plug.

If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery,usually marked BAT.

Speakers (not supplied)Identify the car speaker leads. There are two leads foreach speaker, usually color coded.A handy way to identify the speaker leads and the speak-er they are connected with is to test the leads using a 1.5V AA battery as follows.Hold one lead against one pole of the battery and strokethe other lead across the other pole. You will hear ascraping sound in a speaker if you are holding a speakerlead.If not, keep testing different lead combinations until youhave located all the speaker leads. When you label them,include the speaker location for each.

Connect All LeadsNow that you have identified all the wires in the car,you're ready to begin connecting them to the LCD moni-tor wires. Electrical Connections (a page 12-21) showsthe proper connections and color coding of the leads.We strongly recommend that you test the unit beforemaking a final installation.You can set the unit on the floor and make temporaryconnections to test the unit. Use electrical tape to coverall exposed wires.

Important: Connect the red power lead last, after youhave made and insulated all other connections.

GroundConnect the black ground lead of the power connector tothe metal car chassis.

SpeakersConnect the speaker wires. See the wiring diagram forthe proper hookups. Follow the diagram carefully toavoid damaging the speakers and the stereo unit.

The speakers used must be able to handle more than 50W of audio power. If using optional audio power, thespeakers should be able to handle the maximum amplifieroutput power. Speakers with low input ratings can bedamaged. Speaker impedance should measure 4 – 8 Ω, which istypically marked on most speakers. Lower or higherimpedance speakers will affect output and can causeboth speaker and stereo unit damage.

BatteryConnect the yellow battery lead to the correct radio wireor to the battery fuse port on the fuse block.

EquipmentConnect any optional equipment according to the instruc-tions furnished with the equipment. Read the operatingand installation instructions of any equipment you willconnect to this unit.

PowerConnect the red power lead to the correct car radio wireor to the appropriate fuse port on the fuse block.If the LCD monitor functions properly with all these con-nections made, disconnect the wires and proceed to thefinal installation.

Final Installation Lead ConnectionsConnect all wires, making sure that each connection isinsulated and secure. Bundle all loose wires and fastenthem with tape so they will not fall down later. Now insertthe LCD monitor into the mounting collar.

Congratulations! After making a few final checks, you’reready to enjoy your new LCD monitor.

Caution¡Never ground the speaker cords. For example, do

not use a chassis ground system or a three-wirespeaker common system. Each speaker must beconnected separately using parallel insulatedwires. If in doubt about how your car’s speakersare wired, please consult with your nearest pro-fessional installer.

7

8 CQ-VD6503U

Engl

ish


Final Checks1. Make sure that all wires are properly connected

and insulated.2. Make sure that the LCD monitor is securely held in

the mounting collar. 3. Turn on the ignition to check the unit for proper

operation.

If you have difficulties, consult your nearest authorizedprofessional installer for assistance.

Precautions

¡Disconnect the cable from the negative (–) battery ter-minal (see caution at right).

¡Unit should be installed in a horizontal position withthe front end up at a convenient angle, but less than30°.

Warning¡If your car is equipped with air bag and/or anti-

theft systems, specific procedures may berequired for connection and disconnection of thebattery to install this product.Before attempting installation of this electroniccomponent against the manufacturer's recom-mendation, you must contact your car dealer ormanufacturer to determine the required proce-dure and strictly follow their instructions.FAILURE TO FOLLOW THE PROCEDURE MAYRESULT IN THE UNINTENDED DEPLOYMENT OFAIR BAGS OR ACTIVATION OF THE ANTI-THEFTSYSTEM RESULTING IN DAMAGE TO THE VEHI-CLE AND PERSONAL INJURY OR DEATH.

Caution¡We strongly recommend that you wear gloves for

installation work to protect yourself from injuries.¡When bending the mounting tab of the mounting

collar with a screwdriver, be careful not to injureyour hands and fingers.

This unit should be professionally installed. In case ofdifficulty, please consult with your nearest professionalinstaller.1. This unit only operates in a 12 V DC negative ground

system.2. Follow the Electrical Connections carefully (a page

12-21). Failure to do so may result in damage to theunit.

3. Connect the power lead after all other connections aremade.

4. Be sure to connect the battery lead (yellow) to the pos-itive terminal (+) of the battery or fuse block (BAT) ter-minal.

5. Insulate all exposed wires to prevent short circuiting.6. Secure all loose wires after installing the unit.7. Please carefully read the operating and installation

instructions of the respective equipment before con-necting it to this unit.

Caution¡Please follow the laws and regulations of your

state, province or country for installation of theunit.

Caution¡Various settings that have been stored in the

memory in other on-board equipment (car naviga-tion etc.) may be lost if the battery terminals aredisconnected.Therefore, we recommend you to make a recordof or to back up the settings before disconnectingthe terminals. After completing installation of the main unit, setup the equipment again according to the settings.

0 – 30°

8

9CQ-VD6503U

Engl

ish

—+SIDE BRAKE

The side brake (parking brake) switch position varies with car model.For details on the exact location of the side brake (parking brake) switchin your car, contact your dealer.

q Attach a Clip Connector !2 to the end of the sidebrake (parking brake) connection lead.

w The Clip Connector !2 is connected to the powersource side lead of the side brake (parking brake)lever.

Connecting the Side Brake (Parking Brake) Connection Lead

Hand brake Foot brake

Side Brake (Parking Brake) ConnectionLead (Bright green)When the side brake (parking brake) lever isengaged, the unit is grounded by the chassis.

Side brake (parking brake) switch

Car chassis

BatteryBrake light

!2 Clip Connector

Side Brake (Parking Brake) Connection Lead(Bright green)

Comes up to this point.

Power source side lead

Caution¡For safety, be sure to ask your nearest professional installer to do this connection.

9

10 CQ-VD6503U

Engl

ish


Mounting Procedures (A) (When using Mounting Collar w)

Mounting and removing the Display Unit

Note:¡The car model, installation conditions and combination

of the units used may impose some restrictions onopening and closing the monitor as well as on theangle and position to which the monitor can be adjust-ed.

IMPORTANTWhen this unit is installed in dashboard, ensure that thereis sufficient air flow around the unit to prevent damagefrom overheating. Do not block any ventilation holes onthe unit.

q

w

e

r

t

Insert the Mounting Collar w into the dash-board, and bend the mounting tabs out witha screwdriver.

Establish the rear connection of the unit.After fixing Power Connector !0, fix the rearof the unit to the car body by either method(a) or (b).

Insert the unit into Mounting Collar w.Secure the clamp plate of Mounting Collar wto the hook.

Insert Trim Plate q.

After installation reconnect the negative (–)battery terminal.

Snapping point

q

w

e

t

(a) Using the Rear Support Strap u. (b) Using the Rubber Cushion (option)

Fire wall of car3 mmø

t Tapping Screw (5 mmø x 16 mm)

u Rear SupportStrap

r Mounting Bolt(5 mmø)

To the unit

To the unit

r Mounting Bolt(5 mmø)

Rear SupportBracket(Provided onthe Car)

Rubber Bushing(option)

y Hex. Nut(5 mmø)

Method for Fixing the Rear of the Unit

r

10

11CQ-VD6503U

Engl

ish

Mounting Procedures (B)(When not using Mounting Collar w)Use the brackets supplied with your car when mountingthis unit. The bracket shape and mounting method varywith car manufacturers, car types and manufacturingyear. Please consult your nearest dealer or installer.

Removing Procedures

q Remove the trim plate q.

w Lock release.q Insert the lock cancel plate e until you hear a

click.

w Pull the unit out.

e Pull the unit out both hands.

q

w

Note: Use pliers to bend thefingers on the bracket vertically.

Select mounting screws according to the holepositions and hole shape of the bracket.

i Round Head Screw(5 mmø x 8 mm)

Note:Recycle the Round Head Screws that fixed thetransportation brackets for two more positions. (a page 5)

o Flat-Head Screw(5 mmø x 8 mm)

F U S E 1 5 AF U S E 1 5 AF U S E 1 5 A

8 m m M A X

> P B T < J A M - S A a

AV-OUT

CAMERA-IN

3

5

6

2 41

11

12 CQ-VD6503U

Engl

ish

Electrical ConnectionsCaution

¡This unit is designed for use in a car having a 12 V negative ground battery system.¡Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from

any metal parts.¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery

may clear the memory.¡Run the cords avoiding the spots where the temperature can be extremely high.

Video Output Terminal (AV-OUT)Connect the rear monitor. (a page 21)

Pre-Out Connector (front)To external amplifier.

Pre-Out Connector (rear)To external amplifier.

Pre-Out Connector (center)To external amplifier. Video Input Terminal (AV1-IN)

Video Input Terminal (AV2-IN)

Note: When an external device is connectedto the system-up connector, the audio termi-nals, (R)(Red), (L)(White), of AV2-IN aredisabled.

Connect a VCR, camcorder, other brand’s carnavigation system, etc. (a page 18, 20)

Camera Input Terminal (CAMERA-IN)Connect a rear view camera. (a page 19)

(R)(Red)

(L)(White)

(Yellow)

(Yellow)

(R)(Red)

(Black) (White)

(Red)(Black)

(L)(White)

(Yellow)

qPre-Out Subwoofer connector (mono)To external amplifier.w

e

r

ty

Fuse (15 A) Refer fuse replacement to your nearestauthorized Panasonic Servicenter. Do not try fusereplacement by yourself.

CQ-VD6503U(Rear)

FRONT SP

SIDE BRAKE

REVERSE

ACC

BATTERY 15A

REAR SP

12

13CQ-VD6503U

Engl

ish

Note:¡To prevent from damage to the unit, be sure to follow the wiring diagrams below.¡Be sure to fully plug in the connectors. Secure them with clamps and tapes.¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or

your dealer if other methods are required.

: This book refers to connections to the Panasonic car navigation system that will come onto the market in thefuture. Descriptions regarding the car navigation system are boxed with a dotted line.

Radio Antenna Connector (RADIO ANT IN)

RGB ConnectorTo the Panasonic Car Navigation System (available in future).

System-up ConnectorTo external devices equipped with system-up connector.

!0 Power Connector

Motor Antenna Relay Control Lead (Blue)(To motor antenna) (Max. 100 mA)This lead is not intended for use with a switch actuatedpower antenna.

External Amplifier Control Power Lead (Blue/white stripe)To an external amplifier.Note:¡Use the power control lead of the TV tuner for TV tuner

connection.¡Connect both the power control lead of the TV tuner and

the amplifier control connector of the external amplifierwhen the TV tuner and external amplifier are connectedat the same time.

Navi Mute Lead (Orange)Connect to the Navi Mute Lead of the Panasonic carnavigation system. (available in future)

Side Brake (Parking Brake) Connection Lead (Bright green)Be sure to wire the side brake (parking brake) for safety and pre-venting accidents. (a page 9)

Reverse Lead (Violet/white stripe)When connecting the rear view camera, use the reverselead. (a page 19)

Battery Lead (Yellow)To the car battery, continuous +12 V DC.

Power Lead (Red)To ACC power, +12 V DC.

Front Right + (Gray)Front Right – (Gray/black stripe)

Front Left + (White)Front Left – (White/black stripe)

Rear Right + (Violet)Rear Right – (Violet/black stripe)

Rear Left + (Green)Rear Left – (Green/black stripe)

Speaker connections

• Do not connect more than one speaker to one set ofspeaker leads (except for connecting to a tweeter).

• Do not use a 3-wire type speaker system having acommon earth lead.

Ground Lead (Black)To a clean, bare metallic part of the car chassis

Note: Use a Reverse Extension Cord !1 if needed.

13

14 CQ-VD6503U

Engl

ish

Electrical Connections (continued)

CHANGER IN

BATTERY 5 A

ACC


8 m m M A X

> P B T < J A M - S A a

Connection with DVD Changer (CX-DH801U)

CQ-VD6503U(Rear)

RCA Cord (Video)(Yellow)

(L) (White)

(R) (Red)

DIN Connector

DIN Cord (Black)

DVD ChangerCX-DH801U (option)

Battery Lead(Yellow) To the car battery, continuous +12 V DC

Power Lead (Red) (not used)

(not used)

Ground Lead (Black)To a clean, bare metallic part of the car chassis

Note:¡Refer to the operating instructions for the connected devices, in addition.

Power Connector(Supplied with CX-DH801U)

Conversion Cable for DVD/CD Changer(CA-CC30U, option)

System-upconnector


8 m m M A X

> P B T < J A M - S A a

CHANGER IN

14

15CQ-VD6503U

Engl

ish

(L) (White)

(R) (Red)

DIN Connector

Conversion Cable for DVD/CDChanger (CA-CC30U, option)

Connection with CD Changer (CX-DP880)

CQ-VD6503U(Rear)

System-up connector

DIN Cord (Black)

CD ChangerCX-DP880 (option)

Power Connector(Supplied with CX-DP880)

RCA Cord

Battery Lead (Yellow)To the car battery, continuous+12 V DC

Ground Lead (Black)To a clean, bare metallic part of the carchassis


15

16 CQ-VD6503U

Engl

ish


Connection with TV Tuner (CY-TUN153U) Note:¡Refer to the operating instructions for the connected devices, in addition.


8 m m M A X

> P B T < J A M - S A a

PWR-CONT

TV Tuner CY-TUN153U (option)

CQ-VD6503U(Rear)

(Video)(Yellow)

System-up Connector (supplied with CY-TUN153U)

System-up Connector

!0 Power Connector

Power ControlLead

RCA Cord(option)

Power Connector(supplied with CY-TUN153U)

External Amplifier Control Power Lead Note:¡Connect both the power control lead of the TV tuner and

the amplifier control connector of the external amplifierwhen the TV tuner and external amplifier are connectedat the same time.

Clip connector(option)

16

17CQ-VD6503U

Engl

ish

XM

FUSE

FUSE


8 m m M A X

> P B T < J A M - S A a

XM Satellite Radio XMD1000* (option)

Connection with XM Satellite Radio (XMD1000)

CQ-VD6503U(Rear)

DIN Connector

(L) (White)(R) (Red)

* Please understand that Panasonic is not liable for modification of specifications, shape, name, and the like of theoptional XM receiver and digital adapter without prior notice because they are not manufactured by Panasonic.


System-up Connector

CHANGER IN

VIDEO-CNT


8 m m M A X

> P B T < J A M - S A a

17

18 CQ-VD6503U

Engl

ish


Connection with Expansion Module (CY-EM100U)

CQ-VD6503U(Rear)


VIDEO OUTAUDIO OUT

VIDEO OUT

DVD ChangerCX-DH801U (option)

Expansion ModuleCY-EM100U (option)

Conversion Cablefor DVD/CDChanger (CA-CC30U, option)

Direct Cable for iPod (CA-DC300U, option)

(Video) (Yellow)

(Video)(Yellow)

(Video)(Yellow)

(L) (White)

(L) (White)

RCA cord(option)

(R) (Red)

(R) (Red)

(Video) (Yellow)(L) (White)

(R)(Red)

Head unit/Expansion ModuleConnecting cable(Supplied with CY-EM100U)

Camcorder(option)

iPod

System-upConnector

18

19CQ-VD6503U

Engl

ish

P

ND2L

Panasonic

REVERSE

R


8 m m M A X

> P B T < J A M - S A a

CAMERA-IN

Connecting the Reverse LeadIf using an optional rear view camera, the reverse lead mustbe connected.Connect the reverse lead (violet/white stripe) to the positive (+)lead of the reverse lamp (the lamp with a clear lens that lightswhen the transmission gear is shifted into the reverse position).Note:¡Connect the reverse lead after cutting the terminal at the end.¡Use a Reverse Extension Cord !1 if needed.

Connection with Rear View Camera

Rear View Camera (option)

(Video)(Yellow)

RCA Cord (option)

Rear View CameraControl Unit (option)

CQ-VD6503U (Rear)

(Video)(Yellow)

!0 Power Connector

Reverse lampClip connector(option) Battery Car chassis

Transmission gear!1 Reverse Extension Cord

(Violet/white stripe)

Reverse Lead(Violet/white stripe)

Camera Input

Camera Input Terminal(Yellow)

Check the reverse lamp.

Take it out of the back ofthe tail lamp mount.


19

20 CQ-VD6503U

Engl

ish



8 m m M A X

> P B T < J A M - S A a

INTELLIGENT SYSTEM

BS G-CODE

POWER

Connection with VCR or Camcorder

CQ-VD6503U(Rear)

(R)(Red)

(L)(White)

(Video)(Yellow)

VCR (option)Camcorder (option)

(R) (Red)

(L) (White)

(Video) (Yellow)

RCA Cord(option)

Video Output

Audio RightAudio Left

Note:¡Refer to the operating instructions for the connected devices, in addition.¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in

order to establish a proper connection.

20

21CQ-VD6503U

Engl

ish

RCA Cord (option)


8 m m M A X

> P B T < J A M - S A a

AV-OUT

Connection with Over-head Monitor

(L) (White)

(L) (White)

(R) (Red)

(Video)(Yellow)

Over-head MonitorCY-VHD9401U (option)

(Video) (Yellow)

(R) (Red)

Connection with Headrest Monitor

CY-V7100U


8 m m M A X

> P B T < J A M - S A a

AV-OUT

(Front)

CY-V7100UHide-away unit VTR 1

VTR 2

Headrest MonitorCY-V7100U (option)

RCA cord (option)

(R) (Red)

(R) (Red)

(L) (White)

(L) (White)

(Video)(Yellow)

(Video)(Yellow)


Caution¡For people sitting in the front seats, please enjoy

only audio during driving.

Caution¡For people sitting in the front seats, please enjoy

only audio during driving.

CQ-VD6503U(Rear)

CQ-VD6503U(Rear)

Note:¡Refer to the operating instructions for the connected devices, in addition.¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in

order to establish a proper connection.

6503u ii 01 eng - panasonic · pdf filetv tuner (cy-tun153u, ... you're ready to begin...

Documents