LTE • GSM • UMTS • CDMA and other bands

Measurement display with any commercial Spectrum

Analyzer as Receiver

PC-based control function by Aeroflex 3250™ Series

or advanced Spectrum Analyzer

Up to 30 ~ 46 dBm @ 0.5dB step

Up to -130 dBm (173 dBc) spurious-free dynamic

range in Reverse range

Modular design, Easy upgrade

Compatible with IEC 62037

600 MHz to 3,000 MHz

3rd, 5th & 7th IM measurementPrecise & modular designReflection Reflection & Forward and Two-band Reflection modelsHigh performance & low costSimple & quick IM locatingField proven technologySupports custom designs

The PIMD Analyzer of MPDevice can perform passive intermodulation measurements on major RF bands.

The model of RP • RPF • RPD meet several field applications; such as single reflection, both transmission and reflection and reflection of combined bands.

All models have internal intermodulation levels of -130 dBm during the measurement of third-, fifth-, and seventh-order products as well as deliver a maximum output power of +46 dBm per each tone.

RECEIVER

IM displayGeneral spectrum analyzerExternal 10 MHz source

PC

Receiver controllerResult savingPass/Fail & ATE

* Valid only when Anritsu 2712E Series or later

PIMD MAIN BODY

Two tone sourcesRelated filtersInternal controller

LED DISPLAY

Source freq./level displayStatus of sync. internal orexternal (10 MHz)

2

3

Model Number Application Transmit [MHz] Measurement Ranges [MHz]RP-700 LTE 728~757 690 ~ 713 *RP-800 CDMA, AMPS 869~894 824 ~ 855 *RP-900 EGSM 925~960 865 ~ 905 *

RP-1800 DCS 1805~1880 1710 ~ 1785 *RP-1900 PCS 1930~1990 1850 ~ 1910 *RP-2100 WCDMA, UMTS 2110~2170 1920 ~ 2050 *RP-2300 WiMAX 2130~2140 / 2330~2350 1710 ~ 1980

Forward Measurement IM -127 dBm (-170 dBc), typical

Dimensions (WxDxH) [mm], [Inch] 519x510x443, [20.4x20.1x17.4] **Weight [kg], [lb] ** 40, [88.2] **

Mechanical & Environmental Conditions

Relative Humidity 10% to 90%Ambient Temperature 10 to 40 , 50 to 104

Residual IM with two +43dBm test tones Reverse Measurement IM -130 dBm (-173 dBc), typicalForward Measurement IM (option) -127 dBm (-170dBc), typical

RF Connector Type [ Location] Device Under Test Port [Front] DIN (7/16) FemalIM Signal Port [Front] N Female

External 10 MHz Time Base [Rear] BNC Female

Reverse Measurement IM -130 dBm (-173 dBc), typicalAC supply 100VAC~240VAC, 50/60HzPower Consumption 1KW, max

Power Supply

Fuse 220VAC @ 10A

Amp./Freq. Control Pushbutton [Front]Source Status Monitor LCD Panel [Front]

Test Source Control

Spectrum Analyzer * 30 KHz ~ 3 GHz, -150 dBm Noise FloorIM Cable -170 dBc, + 43 dBm / tone, two carriers, 50 ohms

Optional Equipments

IM Terminations 600 MHz ~ 3000 MHz

Reverse Measurement IM -130 dBm (-173 dBc), typicalWarm-up Time 10 min., minProtection Indoor Use only

Source related

Reverse Measurement IM -130 dBm (-173 dBc), typicalFrequency Increment 1 MHz stepAccuracy, internal ref. ±2ppm, typicalTuning Lock Time 1 , typical

Power Supply

* Note1: The test range is within 5 MHz

** Note2: These apply to the RP series.

RP-900 GSM 935~960 880 ~ 915 *

Operating Description

The PIMD Main Box contains two-test sources, amplifiers, combiner, receiver filter and controller. It generates combined two-tone signals, that are sinusoidal signal having a predetermined frequencies (down link range in mobile network) as F1 and F2.

The two-tone signal are supplied to the device under test (DUT) and reflected wave including passive IM components generated at the input of DUT are passed to the Same port. ThE Receiver Filter screens only receiver range signals (up link range in mobile network) and enables to measure the composite of IM by external spectrum analyzer with easy. The RPF model has another Forward Function Unit to measure IM caused by DUT-output port i.e. Forward IM.

Fast and Easy Analysis

RP Series : Standard Reverse Band Measurement

MPD Measurement Tool

Test Tone

PIMD Main Box (Standard)

Receiver Filter (Measurement)

Reverse IM

Forward IM

PIMD Main Box (Standard)

Forward Function Unit

Term

MPD Measurement Tool

RPF Series : Forward & Reverse Band Measurement

4

f1 source

f2 source

IMs falling to Receiving Band

Reverse IM

DUT

Reverse IM

Forward IM

DUT

Commercial Spectrum Analyzer

Operating Description

The RPD series are designed to meet the measurement of reflected IM in popular two-bands like 800/900 MHz or 1800/1900 MHz.

Please contact MPDevice for other band application.

Fast and Easy Analysis

RPD Series : DUO Reverse Bands Measurement

5

MPD Measurement Tool

Band1Test Tone

PIMD Main Box (DUO)

Receiver Filter (Band1

Measurement)

Band1Reverse IM

Band2Reverse IM

f1 source

f2 source

DUT1

Band2Test Tone

MPD Measurement Tool

DUT2

Band

1 R

ever

se IM

Band2 Reverse IM

Receiver Filter (Band2

Measurement)

Band1Test Tone

Commercial Spectrum Analyzer

12

3 4 5 6

78

9

10 11 12 13

1414

[Front View] *

[Rear View] *

* more detail information is available at http://www.anritsu.com

[Front View]1. Power on/off Switch2. USB3. RS232C Port4. Amplifier On/Off Switch5. Rotary knob (Jog)6 Source status LCD7 DUT port8 IM Signal output port (to Receiver)

[Rear View]9 Power10 AC input11 AMP 1 Output 12 10 MHz Ref Input13 AMP 2 Output14 High Freq. input15 Low Freq. input

* RP series

6

Test Result

Spectrum Display

Easy & Simple

Note : Valid when Aeroflex 3250 or later version.

7

8

The innovative concept of implemented in the RP • RPD • RPF series enhance the analyzer's performance in terms of measurement speed and accuracy. Customers need a PIMD analyzer that is configurable to meet today's needs, yet is upgradeable at a reasonable cost to satisfy future requirements without shattering your test equipment budget. MPDevice's PIMD analyzer deliver the highest performance and the highest value available today.

For extreme requirements, consult withtechnical and helpful field and factory support engineers for custom solutions.

MPDevice provides this high level of performance so that our customers can develop their own state-of-the-art products.With communications systems sharing single antenna and becoming more complex, the IM analysis also becomes more important. For example,when the RP model is used as PIMD analyzer the benefit is clear, a wider spurious free dynamic range - 130 dBm.

Any one of the RP • RPD • RPF series is ideal PIMD Analyzerfor an A.T.E. system. It operates in 19-inch standard EIA rack space.

The Anritsu 2712E series are recommended to expect higher throughput, built-in software co-working with commercial PC using a remote command.

Superior radio frequency engineering experiencein passive devices

Pinpoint IM Locator

Custom designs

In recent years, with the development of wireless communication industry and the shape increase of the communication system demand, there is the design requirement for high performance, reliability and economic feasibility .

Typically, a wireless mobile communication system has a possibility to increase inter-modulation of signal, since many users are communicating by using only several adjacent channels in one antenna. Consequently, there is a possibility to increase damage and distortion of information signal.

PIMD (Passive Inter-modulation Distortion) if occurred after production, almost impossible to recover. So it is becoming an issue in process of improving the wireless communication equipment of AMPS, CDMA, GSM, DCS, PCS, WCDMA & WiMAX bands with high power and maximizing use of channel at each frequency band.

Also, PIMD has been a topic of much discussion as a contributor to performance degradation in mobile radio system.

In addition to providing standard PIMD Analyzers, MPDevice has been supporting customers with custom-engineered solutions. The most mutually beneficial solution (for the customer and MPDevice alike) is the selection of a standard product; however, MPDevice continue to support customers when special models are required.

Product specifications that involve a reasonable first-order quantity and follow-up potential are welcomed.

9

' '

(1) Ex: 824~849 MHz or RP-800

(2) Ex: f1/f2 869~894 MHz or RP-800

(3) Ex: Revere / Forward or DUO* if DUO, please specify both (1) and (2)

(4) Ex: Yes, already we have.* if need 2712E, contact local Anritsu

representative

(5) Ex: 110V, Country* MPD device will ship power cord with customer

country

(6) Available at www.mpdevice.com regarding updated available options & accessories.

Ordering Guide

Please specify the model/order number, name and quantity when ordering.The names listed in the chart below are Order Names.The actual name of the item may differ from the Order Name.

(1) Specify the measurement range or model No.

(4) SPecify if test PIMD with Anritsu 2712E

(5) Specify AC power available and country

(7) Others: Any comment with custom design request

Standard 1-year is provided by MPD

It is required first contacting MPD device for a Return Material Authorization ("RMA") number to be returned directly to MPD device.

If it is determined that the product may be defective, customer will be given an RMA number and instructions for product return.

Warranty & Repair

10

(2) Specify the test source range or model No.

Pleas fill in this ordering information and send it by FAX or email : mpd@mpdevice.com

(1) Company Name:(2) Contact Name:(3) email(3) Telephone /FAX #

(3) Specify the Test format or custom requirement

(6) Specify peripherals and options

Others

.

MPDevice has over 20 years combined experience in passive RF components including connectors, filters(mechanical & DR), duplexers, combiners, RF switches, antennas and especially based on mobile systems.

11

www.mpdevice.com

45B-1L #435, Nonhyun-dong, Namdong-gu, Incheon 405-848 South Korea

Tel : +82-32-822-3290 FAX : +82-32-822-3295email : mpd@mpddevice.com

MPDevice Co., Ltd.