Page 1

General InformatIon

The purpose of this manual is to assist you in operating and maintaining your lawn and garden sprayer. Please read it carefully as it furnishes information which will help you achieve years of dependable trouble free operation.

5301486moDel: tr-30-eX

30 Gallon, 12 Volt lawn & GarDen Sprayer

Assembly / OPerATiOn insTrucTiOns / PArTs

your authorized dealer is the best source of replacement parts and service. To obtain prompt, efficient service, always remember to give the following information:

1. correct part description and part number.2. model number of your sprayer.3. serial number of your sprayer.

Part description and part numbers can be obtained from the illustrated parts list section of this manual.

Whenever you need parts or repair service, contact your distributor / dealer first. For warranty work always take your original sales slip, or other evidence of purchase date, to your distributor / dealer.

technIcal SpecIfIcatIonS

• Low Profile Trailer and Tank• 30 Gallon Polyethylene Tank• 4.10/3.50 x 6 Pneumatic Tires• 12 Volt Diaphragm Pump• 2.1 G.P.M.• Pressure Gauge• Adjustable Pressure Range (0-60 PSI Max.)• Boom-2 Nozzles, 80” Coverage• Lever Handgun• 15 ft. (3/8” - 1 Brd.) Hose

aSSembly InStructIonS

The sprayer is partially assembled at the factory. Follow the instructions below to complete the assembly of this unit.

1. Attach the hitch brackets, both formed and flat, to the trailer frame as shown in the exploded view drawing.

2. The boom brackets are attached with only (2) bolts. Re-move the other (2) bolts from the boom brackets. Loosen the bolts which are holding the boom brackets in place. Then rotate the boom brackets so the other (2) bolts can be

1000 FIMCO LANE • P.O. BOX 1700 • NO. SIOUX CITY, SD 57049TOLL FREE: 800-831-0027 • TOLL FREE FAX: 800-494-0440Form No. 1325 (5004818 3/08) Printed In U.S.A.

w w w . F I M C O I N D U S T R I E S . C O Mwarranty / partS / SerVIce

Products are warranted for one year from date of purchase against manufacturer or workmanship defects.

Do not uSe pump In an eXploSIVeenVIronment. Do not uSe to pump

flammable fluIDS, GaSolIne,KeroSene fuel, oIl, etc.

warnInG

before returnInG thIS proDuctfor any reaSon, pleaSe call

1-800-831-0027If you ShoulD haVe a QueStIon oreXperIence a problem wIth your

fImco InDuStrIeS proDuct:1-800-831-0027

before you call, pleaSe haVe thefollowInG InformatIon aVaIlable:

SaleS receIpt & moDel number. In moStcaSeS, a fImco InDuStrIeS employee canreSolVe the problem oVer the phone.

Page 2

Tip Spray Pressure Capacity GALLONS PER ACRE - BASED ON wATER No. Height (PSI) (GPM) 1 MPH 2 MPH 3 MPH 4 MPH 5 MPH 7.5 MPH 10 MPH

10 .30 44 22 14.9 11.1 8.9 5.9 4.53 18” 20 .42 63 31.5 20.9 15.7 12.6 8.4 6.3 30 .52 76 38 26 19.3 15.4 10.3 7.7 40 .60 90 45 30 22 17.8 11.8 8.9

Tip Spray Pressure Capacity GALLONS PER 1000 SQ. FT. - BASED ON wATERNo. Height (PSI) (GPM) 1 MPH 2 MPH 3 MPH 4 MPH 5 MPH 7.5 MPH 10MPH

10 .30 1.01 .50 .34 .254 .204 .135 .1033 18” 20 .42 1.4 .72 .48 .36 .29 .19 .14 30 .52 1.74 .87 .596 .44 .35 .236 .176 40 .60 2.06 1.00 .688 .50 .408 .27 .20Tip Spray Pressure Capacity GALLONS PER 100 SQ. FT. - BASED ON wATERNo. Height (PSI) (GPM) 1 MPH 2 MPH 3 MPH 4 MPH 5 MPH 7.5 MPH 10MPH

10 .30 .10 .050 .034 .025 .020 .013 .0103 18” 20 .42 .14 .072 .048 .036 .029 .019 .014 30 .52 .174 .087 .059 .044 .035 .0236 .017 40 .60 .206 .1 .068 .050 .040 .027 .020

tip chart

Speed in M.P.H. Time Required in Seconds to Travel a distance of;(Miles Per Hour) 100 ft. 200 ft. 300 ft.

1.0 68 136 205 2.0 34 68 102 3.0 23 45 68 4.0 17 34 51 5.0 14 27 41 6.0 11 23 34 7.0 9.7 19 29 8.0 8.5 17 26 9.0 7.6 15 23 10 6.8 14 20

Speed chart

inserted through the holes, thereby securing the brackets to the trailer frame.

3. Slide the axle through the frame holes, centering it as best as possible.

4. Slide a wheel spacer and a wheel (valve stem out) onto each end of the axle and then use a cotter pin to hold each wheel in place.

5. Attach the boom assembly so that the tips will be about 18 inches above the spraying surface. Use the bolts and hardware to secure the boom in place.

6. Thread the gauge into (Item 31.8). Use a good grade of thread sealant to insure no leaks.

7. Connect the wiring from the wiring assembly to the 12 Volt power source of the vehicle. The red wire of the 2-wire set must be connected to the positive (+) post on the battery or the "hot" connection on a switch or to the ammeter. The brown wire may be grounded or connected to the negative (-) post on the battery.

8. Remove the drain plug assembly from the parts bag and thread it onto the drain bung located at the lower rear end of the tank.

9. Remove the handgun clips/screws from the parts bag, if applicable, and attach them to the side of the tank, for handgun storage.

read the operating instructions and then run the sprayer using only water for testing. initially begin spraying by clos-ing the bypass regulating valve and opening the shut-off valve to the boom. This will enable the air in the line to be eliminated through the tips, while building pressure. When everything tests all right (no leaks, good pressure), add the desired chemicals mixture and water combination and start the spraying operation.

operatIon

This sprayer is designed to be towed behind a garden tractor.

NOTE: Make sure the tires are inflated to 30 P.S.I. prior to usage!

The pumping system draws solution from the tank, through the strainer and to the pump. The pump forces the solution under pressure to the handgun or boom nozzles.

The pump has a pressure switch which will shut the pump off when it reaches 60 PSI.

Pressure may be decreased by opening the bypass valve (Hi-Lo). The more it is opened, the lower the pressure will be.

Handgun Note: The nut on the nozzle which has finger tabs must be tight in order for the spray pattern adjustments to vary when turning the nozzle end.

The nozzles on the boom will spray an 80 inch wide swath. Check the nozzle spray pattern by spraying water on a concrete surface. raise the boom to get more spray pattern overlap if desired.

warnInG: some chemicals will damage the pump valves if allowed to soak untreated for a length of time. Always flush the pump with water after use. Do not allow chemicals to sit in pump for extended times of idleness. Follow chemical manufacturers instructions on disposal of all waste water from the sprayer.

calIbratIon

chemical labels may show application rates in gallons per acre, gallons per 1000 square feet or gallons per 100 square feet. you will note that the tip chart shows all three of these rating systems.

preSSure SwItch operatIonPressure switch is pre-set at the factory. Improper

adjustment of the pressure switch, may cause severe overload or premature failure. If the pump is subjected to rapid cycling during

normal operation, or infrequent periods, damage may occur.

cautIon

Page 3

Once you know how much you are going to spray then de-termine (from the tip chart) the spraying pressure (PSI), and the spraying speed (MPH).conditions of weather and terrain must be considered when setting the sprayer. Do not spray on windy days. Protective clothing must be worn in some cases. Be sure to read the chemical label carefully.Determining the proper speed of the tractor can be done by marking off 100, 200 and 300 feet. The speed chart indicates the number of seconds it takes to travel the distances. Set the throttle and with a running start travel the distances. Adjust the throttle until you travel the distances in the number of seconds indicated by the speed chart. Once you have reached the throttle setting needed, mark the throttle location so you can stop and go again (returning to the same speed).Add water and proper amount of chemical to tank and drive to the starting place for spraying.

When you are ready to spray, turn the boom valve to the “on” position. This will start solution spraying from the tips. The pressure will decrease slightly when the boom is spraying. Adjust the pressure lower by operating the bypass valve.

after SprayInG

After use fill the sprayer part way with water. Start the sprayer

and allow clear water to be pumped through the plumbing system and out through the spray nozzles.

Refill the tank about half full with plain water and use a chemical neutralizer such as Nutra-Sol or equivalent and repeat cleaning instructions. Flush the entire sprayer with the neutralizing agent. Follow the chemical manufacturers disposal instructions of all wash or rinsing water.remove tips and screens from the boom. Wash tips thor-oughly with water or cleaning solution (appropriate for chemi-cal used). Blow out orifice, clean and dry. If orifice remains clogged clean it with a fine bristle (not wire) brush, or with a tooth pick. Do not damage the orifice. water rinse and dry tips before storing.

wInter StoraGe

Drain all water and chemical out of sprayer, paying special attention to pump, handgun and valves. These items are especially prone to damage from chemicals and freezing weather.

The sprayer should be winterized before storage by pumping a solution of RV antifreeze through the entire plumbing. Proper care and maintenance will prolong the life of the sprayer.

Page 4

31.1

31.625

31.2

31.7

31.831.431.3

13

4

33.233.2

33.433.5

2

33.3

31.910

237

10

1010

2

12

33.7 33.9

31.531.2

31.3

13

19

31.6

17

620

22

13

33.9

18

33.8

8

818

8

30.7

30.730.5

202

32 30.6

16

30.430.330.1

30.2

27

1719

21

33.5

233.1

33.4 33.733.3

33.6

33.9

8

33.2

33.933.8

14

5

2311

9

6

26

28

24

29

1514

51692445167007516310051271895117167

511641651010775100359509519850750185070063505818850511145051022503851850385175034531503404250340385024102502110250202155020009501606650063075006209

15

21

23

2526

24

22

18

2019

1716

NumberNo.

7

1211

1413

1098

4

65

23

1

Item Part

Hose Clamp, 1/2"Hose, 1/2"-1 Brd. x 19 3/8"Nylon Cable TieNylon Hose Tee, 1/2" HBNylon Nozzle Cap, 11/16" U.N.F. ThreadDeflectip (Gray)50 Mesh Nozzle Strainer, Red

Nylon Elbow Assembly, 11/16" U.N.F. x 1/2" Boom Mount Angle2-Nozzle Boom AssemblyGold Series 2.1 g.p.m. PumpPort Kit Elbow, 1/2" FNPTFNPTPoly Reducing Bushing, 1/2" MNPT x 1/4" Poly Elbow, 1/2" FNPT x 1/2" FNPTPoly Knurled Swivel Nut, 3/4" FGHTPoly Swivel, 3/8" Hose BarbPoly Swivel, 1/2" Hose BarbGarden Hose Washer#35 Nylon Shut-Off ValveManifoldManifold AssemblyHose Clamp, 5/8"Hose, 5/8"-1 Brd. x 6"Poly Knurled Swivel Nut, 3/4" FGHTPoly Swivel, 5/8" Hose BarbStrainer, 1" Filter WasherPort Kit Fitting, 5/8" Hose Barb#35 Nylon Shut-Off ValveIntake Sub-AssemblyPkg. (2) Handgun Clips & (2) ScrewsLead Wire Assembly (w/Switch), 96"AssemblyDrain Plug Cap, Tether, and Washer

Description

1 501023631.7Trailer Frame (RED: 25 & 30 Gal. "New"

10.50Tank Lid w/Lanyard1

#10-24 x 5/8" Phillips Truss Head Machine

PVC Filter Screen, 1" O.D. x 2.81" Long (30

Poly Bypass "J" Hose (3.8 Pumps & 2.1 [25]

30 Gallon (New Style) TankGauge, 0-100 p.s.i.Low-Flow Handgun w/X-26 TipBushing (25/30 Gallon Trailer)

Cotter Pin, 1/8" x 1"

Boom Bracket (Light Duty)

1

Screw

Mesh)

2

11

1

4

Gallon)

GrommetStyle Tanks)

2

21

11

33.933.833.733.633.533.433.333.233.1

31.931.8

4.00

5.999.95

.25

.251.952.001.0031.95

3233

HB2 5056023

5051022 5020416 5133094 5086003 5046052 5138512 5116019

1

24

2

22

2

502241152757265275703

5010430 5041073

1

11

11

4.10/3.50-6 Wheel (White) w/2 1/4" Offset &

Hose Clamp, 3/8"Hose Clamp, 1/2"Hitch Bracket (Flat)Hitch Bracket (Formed)5/16"-18 x 5/8" Flange Lock ScrewH.H.C.S., 5/16"-18 x 1"H.H.C.S., 5/16"-18 x 3/4"Axle (5/8" Dia.)

Hose, 3/8"-1 Brd. x 15 Ft.Hose, 1/2"-1 Brd. x 26"Garden Hose Washer5/16"-18 Hex Whiz (Flange) LocknutPoly Knurled Swivel Nut, 3/4" FGHT

1

11

22

426

5/8" BB

1

21

81

1

DescriptionQty1527551530

Price

31.631.531.431.331.231.1

30.730.630.530.430.330.230.1

318.11

.63

.622.304.85.44.25.55

29.958.502.66.20.25.38

152755162 5051023

5006209 5149034 5149035 5016066 5143188 5143404

12

21

21

5020080 5006209 5149036 5116242 5168835 5143188

11

11

11

Item

List 2829

27

No.

527488052744435274373

NumberPart

11

1

Qty

1.87

.621.55.20.88.38.951.011.104.4921.50

112.002.491.26

.38

.48

.38

.202.538.99

18.00.675.12.38.58.312.242.536.502.859.992.95

PriceList

TR-30-EX (5301486)

Exploded View/Parts List: