43447 bullet cartridge pen - rockler woodworking and hardware

43447 © Rockler Companies Inc. 2012 Visit Rockler.com for the most current product information and videos or call 1-800-260-9663. Blank Preparation 1. Cut the blank about 1/8" longer than the Brass Tube to allow for “blow-out” or hole elongation. 2. Drill the blank with a 10mm drill bit at a speed of 900 to 1200 RPM. 3. Polish the Brass Tube with 220 grit sandpaper to remove oxidation and roughen the Tube for better adhesion. This can be done by hand or by chucking it in a drill press or portable hand drill. 4. Prepare to glue with medium CA (cyanoacrylate) glue or two-part fast drying epoxy. 5. Apply the glue to the outside of the Brass Tube with a liberal amount around the end that is inserted first. Do not apply glue to the inside of the blank, as this will cause the glue to get inside the Brass Tube and ruin it. 6. Insert the Brass Tube with a twisting motion into the blank until the Tube is equidistant between both ends of the blank. Wipe off any excess glue on the ends of the blank. Allow the glue to dry. 7. Using a barrel trimmer, disk, or belt sander, trim the ends of the blank until you can just see the bright brass ends of the Tube. The face of the ends must be perpendicular to the Brass Tube and parallel with each other. It is imperative to match the length of the trimmed blank to the original length of the Brass Tube and that the inside of the Brass Tube is clean and free of any glue. Chrome Bullet Cartridge Pen Preparation and Turning Brass Tube Nut Mandrel “A” Wood Spacer Bullet Bushing Set Mandrel “A” Setup: Nut Adjustable Mandrel Brass Tube Adjustable Mandrel Setup: Bullet Bushing Set Turning the Blank 1. Assemble the blank on the mandrel with the bushings placed on either side of the blank. Each bushing has a step that is designed to be inserted into the Tube for stability while turning, as the inner diameter of the Tube is larger than the mandrel. Note that all of the bushings are the same size. Note: Either Wood Spacers or extra Bushings may be used to fill the extra space on the mandrel. 2. Tighten the tailstock and then tighten the mandrel nut that holds the blank. Do not over-tighten the tailstock or mandrel nut as this may cause the mandrel to flex, causing the blank to go out of round. 3. Turn the blank to the desired shape, making sure that the surfaces next to the bushings are turned to the same diameter as the bushings. 4. After turning, sand the surfaces in progressive steps of 220, 400, 600, and 1000 grit. If a higher finish is desired, micromesh sandpaper may be used. 5. Apply the finish of choice and polish. 6. Remove the blank from the mandrel.

Upload: others

Post on 18-Dec-2021

5 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

43447

Blank Preparation1. Cuttheblankabout1/8"longerthantheBrassTubetoallow for“blow-out”orholeelongation.

2. Drilltheblankwitha10mmdrillbitataspeedof900 to1200RPM.

3. PolishtheBrassTubewith220gritsandpapertoremove oxidationandroughentheTubeforbetteradhesion.This canbedonebyhandorbychuckingitinadrillpressor portablehanddrill.

4. PreparetogluewithmediumCA(cyanoacrylate)glueor two-partfastdryingepoxy.

5. ApplythegluetotheoutsideoftheBrassTubewithaliberal amountaroundtheendthatisinsertedfirst.Donotapplyglue totheinsideoftheblank,asthiswillcausethegluetoget insidetheBrassTubeandruinit.

6. InserttheBrassTubewithatwistingmotionintotheblank untiltheTubeisequidistantbetweenbothendsoftheblank. Wipeoffanyexcessglueontheendsoftheblank.Allowthe gluetodry.

7. Usingabarreltrimmer,disk,orbeltsander,trimtheends oftheblankuntilyoucanjustseethebrightbrassendsof theTube.Thefaceoftheendsmustbeperpendicularto theBrassTubeandparallelwitheachother.Itisimperative tomatchthelengthofthetrimmedblanktotheoriginallength oftheBrassTubeandthattheinsideoftheBrassTubeis cleanandfreeofanyglue.

Chrome Bullet Cartridge Pen Preparation and Turning

Brass Tube NutMandrel “A”

Wood Spacer

Bullet Bushing Set

Mandrel “A” Setup:

Nut

Adjustable Mandrel

Brass TubeAdjustable Mandrel Setup:

Bullet Bushing SetTurning the Blank1. Assembletheblankonthemandrelwiththebushingsplaced oneithersideoftheblank.Eachbushinghasastepthatis designedtobeinsertedintotheTubeforstabilitywhile turning,astheinnerdiameteroftheTubeislargerthan themandrel.Notethatallofthebushingsarethesamesize. Note:EitherWoodSpacersorextraBushingsmaybeused tofilltheextraspaceonthemandrel.

2. Tightenthetailstockandthentightenthemandrelnutthat holdstheblank.Donotover-tightenthetailstockormandrel nutasthismaycausethemandreltoflex,causingtheblank togooutofround.

3.Turntheblanktothedesiredshape,makingsurethat thesurfacesnexttothebushingsareturnedtothesame diameterasthebushings.

4.Afterturning,sandthesurfacesinprogressivestepsof 220,400,600,and1000grit.Ifahigherfinishisdesired, micromeshsandpapermaybeused.

5.Applythefinishofchoiceandpolish.

6. Removetheblankfromthemandrel.

Page 2: 43447 Bullet Cartridge Pen - Rockler Woodworking and Hardware

43447 - Rev 05/12

WARN

ING: T

his product contains one or m

ore chemicals,

including lead, that are known

to the State of California to

cause cancer and birth defects or other reproductive harm

. W

ash hands after handling.

Made in C

hina

Distributed by R

ockler C

ompanies Inc.

ockler Woodw

orking and H

ardware

4344

7 - R

ev 0

5/12

rom

lle

t C

art

rid

sse

Inst

ruc

tio

nsC

hro

llet

rtridg

e P

ssem

bly

Instru

ctio

AssemblyReadtheassemblyinstructionscompletelybeforeassembly.

1. PresstheCenterBandintotheBrassTube.

2. PresstheCapAssemblyintothefarendoftheBrassTube.

3. SlidetheSpringontothewritingtipoftheInkCartridge.

4. InserttheInkCartridgeintotheCartridgeAssembly.

5. SlidetheTwistMechanismovertheendoftheInkCartridge andthreadintotheCartridgeAssembly.

6. GentlypushthecompletedTubeassemblyontothe TwistMechanismbyhand.

Reordering Information Stock #GoldBulletCartridgePenKit...............................434477mmMandrel“A”with#2MorseTaper...............435377mmMandrel“A”with#1MorseTaper...............39389Adjustable7mmMandrel“A”with#2MorseTaper............................................25581BulletBushingSet................................................4345110mmDrillBit.......................................................37216PenMillKit...........................................................47526

Chrome Bullet Cartridge Pen Assembly

Cap Assembly

Spring

Cartridge Assembly

Ink Cartridge

Brass Tube

Center BandTwist Mechanism

57550 Small Parts Taper Jig Inst - Rockler Woodworking and

ROCKLER INTRODUCES SMALL-PROJECT …ww1.prweb.com/prfiles/2018/01/02/15049132/Mini Sure-Foot...2018/01/02 · MEDINA, MN. (Jan. 3, 2018) – Rockler Woodworking and Hardware has expanded

45° Miter Sled Instructions - Rockler Woodworking and ...go.rockler.com/tech/31593-Miter-Sled-Inst.pdf · 45° Miter Sled Instructions 31593 Rev 08/14 © Rockler Companies Inc. 2014

FESTOOL - Rockler Woodworking and Hardware

6 pack holder - Rockler Woodworking and HardwareBottle Caddy OTHER MATERIALS • Glue and dowels • Sandpaper • Drying oil or wipe-on finish GET FROM ROCKLER Stock # Item 3/4" Oak