4 function - universal remote control...

Thank you for purchasing a Philips Magnavox 4 device universalremote control. This universal remote control will operateyour Television,Video Cassette Recorder, DVD, Cable ConverterBox or Audio Receiver/Amplifier. Before you can use your newremote control, you will need to program it to operate the spe-cific components you wish to control. This remote features:

• Channel Scan, a convenient way to "channel surf"by scanning channels.

• Auto Scan code search to help program remotecontrol for a variety of components, includingolder/discontinued models.

• Built-in Sleep Timer.• Controls for basic functions, including Power,

Channel Selection,Volume, Play and Record.

KEYS AND FUNCTIONS

2

1

2

3

5

4

7

10

11

13

14 15

13

12

10

38

596

16

4 Functionwith Back Lighted Keypad

Universal Remote

Instructions . . . . . . . . . . . . . 2Instrucciones . . . . . . . . . . 10Instructions . . . . . . . . . . . . 19

Replacement and Code Saver

When the batteries need replacing the remote control will stop work-ing and will require two (2) new "AA" alkaline batteries for continuedoperation. Once you remove the old batteries, program settings andcodes will be saved for 10 minutes, allowing adequate time to insertnew ones.

However, if you do not replace the batteries within the allotted time(e.g., 10 minutes), you will have to reprogram the remote control.

USING THE LIGHTED KEYPAD

When activated, the remote control features a lighted keypad that illu-minates all of the remote control keys whenever you press any key.

1. To turn on the keypad back light, press LIGHT once.The keypad will remain lit for 5 seconds after you releaseany key.

2. To turn off the keypad back light, press LIGHT onceagain. (The keypad will not light whenever you press anykey.)

PROGRAMMING YOUR REMOTE CONTROL

Philips/Magnavox Components

The remote control can control up to three different components andis already pre-programmed for use with newer Philips/Magnavoxaudio/video equipment. Unless you want to change a factory setting,skip the programming instructions and simply start using your newremote control.

Programming Other Components

To control component brands other than Philips/Magnavox, you’ll needto perform the following steps to manually program the remote withcodes listed under Manufacturer’s Codes on pages 28 through 37. Oras an alternative, you can use the Auto Scan feature, on page 5, to pro-gram your component codes.

The following chart lists the remote component keys and what type ofdevice each key will control:

Key Programmed to Control

TV TV

VCR VCR or DVD

CBL Cable Box

AUD Amplifier/Receiver

NOTE: If you want the component keys to control other types ofdevices, you’ll need to reassign the component keys. See page 5.

IMPORTANT: Please completely read and review the followingsteps before proceeding. We recommend highlighting the codes (start-ing on page 28), for the brands you wish to program or writing themdown in the supplied chart.

Setup Codes for My componentsTV ___ ___ ___ ___

VCR ___ ___ ___ ___

CBL ___ ___ ___ ___

AUD ___ ___ ___ ___

To Manually Program the Remote Control:

1. Manually turn on a component (e.g.,TV,VCR, etc.) and, ifapplicable, insert media (e. g., cassette).

2. On the remote control, press a component keyonce (e.g., TV,VCR,CBL, or AUD).

3. Press and hold SET (approximately 5 seconds) until thered light blinks twice, then release SET.

4. Enter the first four-digit code for your brand of compo-nent. If performed correctly, the red light will blinktwice.

4

SETTING UP YOUR REMOTE CONTROLBefore using your new remote control, you will need to obtain andinstall new batteries, as described below. Then you’ll also need to pro-gram the remote control with the correct code numbers for your spe-cific components. See instructions starting on page 4.

ABOUT BATTERIES Note: The remote requires two (2) new "AA" alkaline batteries (notsupplied). Do not mix old and new batteries or mix alkaline with man-ganese-type batteries.

Installing Batteries

1. On the back of the remote con-trol, push the tab and lift the bat-tery compartment cover off.

2. Match the + and – marks on thebatteries to the + and – marks inthe battery case and insert two (2)"AA" alkaline batteries.

3. Press the battery cover back intoplace. The tab should click whenthe cover is locked.

4. Test the unit by pressingPOWER and any Component key(e.g., TV, VCR, CBL, etc.). If thebatteries are inserted correctly thered indicator light will blink once.

Battery SaverThe remote has a Time Out feature that will automatically deactivate theremote control if a key is depressed for more than 30 seconds. This fea-ture will help conserve the battery life should your remote control getstuck in a place where keys remain depressed (e.g., between the sofacushions).

3

1 Red Indicator LightThe Red Indicator Light blinksto show that the remote con-trol is working and also pro-vides feed back during pro-gramming sequences.

2 Component KeysPress TV, VCR, CBL orAUD once to select a homeentertainment component tocontrol.

3 CH KeysUse CH+ (or CH-) to selectthe next higher (or lower)channel for the selected homeentertainment component.

4 SLEEP KeyPress SLEEP to activate yourTV’s internal sleep timer (notavailable for all TVs) or to pro-gram timer.

5 VOL KeysUse VOL+ (or VOL-) toraise (or lower) the soundvolume.

6 POWER KeyPress POWER once to turnon or off the selected homeentertainment component.

7 MUTE KeyPress MUTE once to turnsound off or on.

8 LAST KeyPress LAST once to recallthe last channel.

9 SET KeyUse SET for all programmingsequences.

10 KeypadUse the keypad (0-9) todirectly enter in channels (forexample, 09 or 31). The key-pad is also used for all pro-gramming sequences, such asentering in your programmingcodes.

11 SCAN KeyPress SCAN once to changechannels every 3 seconds.Press it again to stop the scan.

12 ENTERUse ENTER once afterentering channel numbers onsome TV models.

13 VCR Transport KeysUse the VCR Transport Keysto control your VCR. PressREC twice to record a tape.

14 TV/VCRPress TV/VCR once to viewVCR playback or TV throughthe VCR.

15 FAV CH KeyUse to pre-program up to 10favorite channels.

16 LIGHT KeyPress LIGHT once to turn onor off the keypad backlight.

1

2

3

1. Press and hold SET until the red light blinks twice, thenrelease SET.

2. Enter 9-9-2. The red light will blink twice.

3. Press the Component key (e.g., TV, VCR, etc.) to bemoved once, then press the Component key (e.g.,

AUD, etc.) to be re-assigned once. When re-assignment is done, the red light will blink twice toconfirm your choice.

4. The re-assigned key is now ready to be programmed forthe component. See Programming Your Remote Control onpage 4.

Example – Re-assigning The AUD key to be a DVD (Or VCR) key:For example, to have the remote control a TV, a Cable Converter, andtwo VCRs, you will need to re-assign the unused AUD key to operatethe second VCR as follows:



3. Press VCR once.

4. Then press AUD once. When re-assignment is done,the red light will blink twice to confirm your choice.

5. The AUD key is now ready to be programmed for yourDVD (or VCR) player. See Programming Your RemoteControl on page 4.

ABOUT OTHER FEATURES

Volume LockThe remote control is set at the factory to control the volume inde-pendently while in the TV,VCR, and CBL modes.

To control the volume from one mode (e. g., TV) while in anothermode (e.g., VCR or CBL), perform the instructions below to lock thevolume setting. This procedure will not affect separate control of youraudio component’s volume in the AUD modes.

NOTE: By pressing AUD before entering the sequence below, theremote control will operate your home theater volume controls in allmodes.This feature does not apply to component keys that have beenre-assigned.

1. On the remote control, press TV once.


3. Press VOL+. The red light will blink twice.

Scan Key

The SCAN key allows the remote control to scan the TV,VCR andCBL channels. When activated, the remote control will change chan-nels every 3 seconds.

1. On the remote control, press TV,VCR or CBL once.

2. Press SCAN once. Scanning will start with the currentchannel, then proceed to the next channel up, and con-tinue until all channels of your TV,VCR or CBL compo-nent are scanned.

3. To stop scanning channels, press SCAN.

Favorite Channel Scan

The FAV CH Key can be pre-programmed with up to 10 of yourfavorite channels and scans these only.1 On the remote control, press a component key once

(e.g., TV,VCR, CBL) .

6

5. Aim the remote control at the component and pressPOWER ONCE. It should turn off. If it does notrespond, repeat steps 2 and 3, trying each code for yourbrand until you find one that works. If it still does notwork, try using Auto Scan (see below) on how to pro-gram your component.

6. Repeat steps 1 through 5 for each component you wantto program into the remote control.

NOTES: Press each key within 10 seconds of the previous entry.Otherwise, the remote control will exit the programming mode.

If you press SET at any time (except during step 3), the remote con-trol will exit the programming mode without saving your entries. Youwill have to start with step 1 to begin programming again.

Programming With Auto Scan

If your component does not respond to the remote control after try-ing all codes listed for your brand, or if your brand is not listed at all,try searching for your code using Auto Scan. For example, to searchfor a code for a TV:1. On the remote control, press TV once.


3. Aim the remote control at the TV and press SCAN. Thered light will blink twice.

4. Continue aiming the remote control at the TV (whichmay take up to 5 minutes) until it turns off. Immediatelypress any key except VOL-, LAST, SCAN, or SET.

If SCAN is pressed again after any key stops Auto Scan, the remotewill continue Auto Scan of the next ID from where it stopped.

If you have passed by the code that turns off the TV, press VOL- oneor more times until the TV turns on again.

5. To lock in the code and exit Auto Scan, press and releaseSET the red light will blink twice.

6. To search for codes of other components, repeat steps 2through 5, but substitute the appropriate key (e.g.,VCR,CBL) for the (VCR or Cable) component you are search-ing for.

NOTES: In the search mode, the remote will send IR (infrared)codes from its library to the selected device, starting with the mostpopular code first.

Checking the Auto Scan Codes

If you have set up the remote control using Auto Scan, you can nowfind out which four-digit code is operating your component:1. On the remote control, press a component key once

(e.g., TV,VCR, CBL or AUD).



4. To view the code for the first digit, press 1 once. Wait3 seconds, count the red light blinks (e. g., 3 blinks = 3)and write down the number.

NOTE: If a code digit is "0" , the red light will not blink.

5. Repeat step 4 three more times for remaining digits. Use2 for the second digit, 3 for the third digit and 4 for thefourth digit.

6. To find codes of other components, repeat steps 1through 5, but substitute the appropriate key (e.g., VCRor CBL) for the component you are checking. Asbefore, write down each four-digit code.

Re-Assigning Component KeysThe remote can be set up to control any combination of four homeentertainment components. By following these instructions, you canre-assign or duplicate a component key onto an unused componentkey.

5

8

Press component* key once (e.g., CBL).

Press SETuntil Red Lightblinks twice;release SET.

Press VOL+ once.Volume now controlledthrough component selected in step 1.

x 2

1 2 3

* NOTE: Component must have volume capabilities.

Volume Lock

QUICK FEATURES SETUP GUIDE

This guide is provided here for your convenience as a quick refer-ence for performing remote control sequences.

Turn oncomponent(e.g., TV).

Press componentkey once

(e.g., TV).


Enter 4-digit codefor your brand;

Red Light blinkstwice after last #.

Press POWERonce; if no response,

repeat stepswith next code.

x 2

x 2

# # # #

1 2 3 4 5

Component Setup

Turn oncomponent(e.g., TV).


(e.g., TV).


Aim remote atcomponent; pressSCAN once. When

off, press anykey* to stop.

x 2

Press SETuntil Red Light

blinks twice;release SETto lock code.

x 2

1 2 3 4 5* NOTE: Not VOL-, LAST, SCAN, or SET.

Auto Scan


(e.g., TV).


Enter 9-9-0;the Red Light

will blink twice.

Press 1 once for 1st digit. Wait 3 sec. and count blinks.

Number of blinks equalsvalue of code digit.

Repeat with 2, 3, and 4.

x 2x 2

1 2 3 4

Code Verification

Press component keyto be moved once

(e.g.,VCR).


x 2

3

Press component keyto be reassigned once

(e.g., AUD). Red Light willblink twice. Reassigned key isnow ready for programming.

41


will blink twice.

x 2

2

Device Re-Assignment (e.g., AUD Key Becomes Secondary VCR Key)

Press and release SET once. Red

Light blinks twice.Repeat for up to

10 channels.

x 2

5

Enter channelNote: Some brands

require ENTER after channel.

4

Programming The FAV CH Key

Press componentkey once (e.g., TV).



will blink twice.

x 2x 2

1 2 3



4. Enter first channel, e.g., 07. For some component brandsthe ENTER key must be pressed after the digits, this willcount as a key press. Skip Step 5 if ENTER is needed asnext channel number will be ready to program withoutpressing SET.

5. Press and release SET once (do not hold down). Redlight blinks twice.

6. Enter second channel, third channel etc. until 10th chan-nel is reached. Note: If 3 digits plus an Enter is need-ed for newer TVs/Cable channels, these will not be pro-grammed. Only 3 entries per channel can be accepted.

7. FAV CH program exits after 10th channel is pro-grammed or if SET is pressed for 3 seconds.

8. Pressing FAV CH key activates the remote to cyclethrough the favorite channels every 3 seconds untilfavorite channel is locked in by pressing any key.

Note: Favorite channel scan will only work on the component it isprogrammed to.

Punch ThroughThe VCR Transport keys (e.g., REW, PLAY, FFWD, REC, STOP,AND PAUSE) are set at the factory to control the VCR even if TVor CBL is the selected mode. In other words,VCR control "punchesthrough" regardless of what mode is on. Moreover, you do not have topress VCR before pressing the mode key.

However, if AUD is the selected mode, the VCR Transport Keys willnot control the VCR unless you press the VCR first. In these twomodes, the VCR Transport Keys will operate the functions for theselected component.

Sleep FeaturePress SLEEP key to activate your component’s internal sleep timer.(May not be available for all components.) If the component does nothave a sleep function, the first press of the SLEEP key activates theremote’s built-in sleep timer. Timer can be set to a maximum of 90minutes.

To Set the Remote’s Built-in Timer1. Press SLEEP key once, 15 minute timer is set. Red light

blinks once.

2. Additional key presses within 10 seconds will increasethe timer value in 15 minute increments up to a maxi-mum of 90 minutes. For each press of the SLEEP key,the red light will blink to indicate how many 15 minuteincrements have been programmed, e.g., one blink forfirst press, two blinks for the second press, etc. Sleeptimer activates 10 seconds after the last press of theSLEEP key. The red light will blink once every 15 sec-onds to indicate that the timer is running.

NOTE: Once the sleep timer is running, the sleep timer is automati-cally canceled if any other key is pressed. The remote IR must bepointed to the component to turn off component when timer ends.

To Activate Built-in Sleep Timer if component hasSleep function1. On the remote control, press a component key once

(e.g., TV, VCR,CBL). Sleep feature does not apply to AUD mode.



4. Follow instructions above to Set Timer.

To reset to component Sleep function follow steps 1through 3 above. At the end of step three, the red lightwill blink four times to indicate the remote is reset tocomponent Sleep function.

7

SETUP CODES FOR TELEVISION CÓDIGOS DE PROGRAMACIÓN PARA TELEVISIÓNCODES DE PROGRAMMATION DU TÉLÉVISEUR

A-Mark 0032AOC 0032, 0048, 0059, 0214Admiral 0122, 0492Adventura 0075Aiko 0121Akai 0059Alaron 0208Ambassador 0206America Action 0209Ampro 0780Anam 0209Anam National 0084Archer 0032Audiovox 0032, 0121, 0209, 0480, 0652Baysonic 0209Belcor 0048Bell & Howell 0045, 0183Bradford 0209Brockwood 0048Broksonic 0032, 0265, 0492CXC 0209Candle 0059, 0075, 0085Carnivale 0059Carver 0083Celebrity 0029Cineral 0121, 0480Citizen 0059, 0068, 0075, 0085, 0089,

0121, 0309Clairtone 0214Concerto 0085Contec 0209, 0214Craig 0209Crosley 0083Crown 0068, 0209Curtis Mathes 0045, 0059, 0068, 0076, 0080,

0083, 0085, 0089, 0122, 0174,0183, 0195, 0480, 0495

Daewoo 0048, 0068, 0121, 0480, 0652,0653

Daytron 0048Denon 0174Dumont 0046, 0048Dwin 0749, 0803Electroband 0029, 0214Emerson 0048, 0068, 0183, 0206, 0207,

0208, 0209, 0214, 0265, 0309,0311, 0492, 0652, 0653

Envision 0059Fisher 0183, 0188Fujitsu 0208, 0712Funai 0200, 0208, 0209Futuretech 0209GE 0050, 0076, 0080, 0084, 0122,

109

TROUBLESHOOTING

Red Indicator Light does notblink when you press a key.

Replace the batteries with two(2) "AA" alkaline batteries (seePage 3).

The VOL+,VOL- and MUTEkeys are not functional.

Make sure that the volume con-trol is locked to a componentthat has volume capabilities and isprogrammed into the remotecontrol.

Red Indicator Light blinks whenyou press a key, but home enter-tainment component does notrespond.

Make sure you are aiming theremote control at your homeentertainment component andthat you are within 15 feet of thecomponent you are trying tocontrol.

The remote control does notcontrol home entertainmentcomponents or commands arenot working properly.

Try all listed codes for the com-ponent brand being set up. Makesure all components can be oper-ated with an infrared remotecontrol.

CH+, CH- and LAST do notwork for your RCA TV.

Due to an RCA design (1983-1987), only the original remotecontrol will operate these func-tions.

Changing channels does notwork properly.

If original remote controlrequired pressing ENTER tochange channels, to change chan-nels, press ENTER on theremote after entering a channelnumber.

Tried Auto Scan and still couldnot find a working code.

Try Auto Scan again after clearingout the component key as fol-lows: Press and hold SET untilRed Light blinks twice, thenrelease. Next enter 9-9-2. Thenpress and release the componentkey to be cleared twice.

NOTE: To clear all set up codes and restore functions to Default,press SET until red light blinks twice, release SET and enter 9-8-1.Caution:When this clear feature is performed, please note that all ofyour set up codes will be reset to the default codes and you will needto reprogram components.

PROBLEM: SOLUTION:

Philips 0083Pilot 0048, 0059, 0068Pioneer 0195Portland 0048, 0068, 0121Prism 0080Proscan 0076Proton 0032, 0207, 0495Pulsar 0046, 0048Quasar 0080, 0084, 0194, 0279RCA 0047, 0048, 0076, 0080, 0119,

0122, 0164, 1476Radio Shack 0048, 0059, 0068, 0076, 0085,

0183, 0194, 0207, 0209Realistic 0048, 0059, 0068, 0085, 0183,

0194, 0207, 0209Rhapsody 0214Runco 0046, 0059, 0632SSS 0048, 0209Sampo 0059, 0068Samsung 0048, 0059, 0085, 0089, 0207Samsux 0068Sansei 0480Sansui 0492Sanyo 0183, 0188Scimitsu 0048Scotch 0207Scott 0048, 0207, 0208, 0209, 0265Sears 0076, 0083, 0085, 0183, 0185,

0188, 0200, 0207, 0208Semivox 0209Semp 0185Sharp 0068, 0122, 0194Shogun 0048Signature 0045Simpson 0216Sony 0029Soundesign 0207, 0208, 0209Spectricon 0032Squareview 0200Starlite 0209Supre-Macy 0075Supreme 0029Sylvania 0049, 0059, 0083, 0125Symphonic 0200TMK 0085, 0206, 0207Tandy 0122Tatung 0032, 0084Technics 0080, 0279Technol Ace 0208Techwood 0032, 0080, 0085Teknika 0045, 0048, 0068, 0083, 0085,

0089, 0121, 0179, 0208, 0209Telefunken 0085Toshiba 0089, 0183, 0185Tosonic 0214Totevision 0068

12

0164, 0207, 0311, 0480Gibralter 0046, 0048, 0059GoldStar 0048, 0059, 0085, 0207Gradiente 0082, 0085Grunpy 0208, 0209Hallmark 0207Harley Davidson 0208Harman/Kardon 0083Harvard 0209Hitachi 0045, 0085, 0174, 0180Infinity 0083Inteq 0046JBL 0083JCB 0029JVC 0082Janeil 0075KEC 0209KTV 0059, 0068, 0209, 0214, 0309Kenwood 0048, 0059Kloss 0075LG 0085LXI 0076, 0083, 0183, 0185, 0207Logik 0045Luxman 0085MEI 0214MGA 0048, 0059, 0179, 0207MTC 0048, 0059, 0085, 0089, 0214Magnavox 0049, 0059, 0083*, 0125,

0208, 0216Majestic 0045Marantz 0059, 0083Matsushita 0279Megatron 0032, 0174, 0207Memorex 0045, 0085, 0179, 0183, 0207,

0279, 0492Midland 0046, 0068, 0076, 0080, 0164Minutz 0050Mitsubishi 0048, 0122, 0179, 0207Motorola 0084, 0122Multitech 0209NAD 0185, 0195, 0207NEC 0048, 0059, 0085NTC 0121Nikko 0059, 0121, 0207Noshi 0047Onwa 0209Optimus 0183, 0195, 0279Optonica 0122, 0194Orion 0208, 0265, 0492Panasonic 0080, 0084, 0279Penney 0032, 0047, 0048, 0050, 0059,

0068, 0076, 0080, 0085, 0089,0164, 0185, 0207

Philco 0048, 0049, 0059, 0083, 0125,0174, 0492

11

* Default code

GoldStar 0066, 0067Gradiente 0029, 0037HI-Q 0076Harley Davidson 0029Harman/Kardon 0067, 0110Harwood 0101Headquarter 0075Hitachi 0029, 0070, 0071, 0134Hughes Network Systems 0071JVC 0037, 0070, 0096Jensen 0070KEC 0066, 0307KLH 0101Kenwood 0067, 0070, 0096Kodak 0064, 0066LXI 0066Lloyd’s 0029, 0237Logik 0101MEI 0064MGA 0072, 0090, 0269MGN Technology 0269MTC 0029, 0269Magnasonic 0307Magnavox 0029, 0064, 0068, 0110*,

0178Magnin 0269Marantz 0064, 0110Marta 0066Matsushita 0064, 0191Memorex 0029, 0064, 0066, 0068, 0075,

0076, 0077, 0133, 0238, 0269,0336, 1191

Minolta 0071, 0134Mitsubishi 0072, 0077, 0090, 0096Motorola 0064, 0077Multitech 0029, 0101NEC 0067, 0070, 0096, 0133Nikko 0066Nikon 0063Noblex 0269Olympus 0064Optimus 0066, 0077, 0133, 0191, 0461,

1191Optonica 0091Orion 0031, 0213, 0238, 0508Panasonic 0064, 0191, 0254, 0645, 1191Penney 0064, 0066, 0067, 0071, 0083,

0269Pentax 0071, 0134Philco 0064, 0238, 0508Philips 0064, 0091, 0110, 0647Pilot 0066Pioneer 0096Portland 0049Profitronic 0269

14

* Default code

Vector Research 0059Victor 0082Vidikron 0083Vidtech 0048, 0207Viking 0075Wards 0045, 0048, 0049, 0050, 0059,

0083, 0085, 0125, 0194, 0207,0208

White Westinghouse 0492, 0652, 0653Yamaha 0048, 0059Zenith 0045, 0046, 0121, 0492, 0653Zonda 0032

SETUP CODES FOR VCRCÓDIGOS DE PROGRAMACIÓN PARA VIDEOCASETERA.CODES DE PROGRAMMATION DU MAGNÉTOSCOPE.

Admiral 0077, 0238Adventura 0029Aiko 0307Aiwa 0029, 0066, 0336Akai 0070, 0090, 0135America Action 0307American High 0064Asha 0269Audiovox 0066Beaumark 0269Bell & Howell 0133Broksonic 0031, 0150, 0213, 0238, 0508CCE 0101, 0307Calix 0066Canon 0064Capehart 0049Carver 0110Cineral 0307Citizen 0066, 0307Colt 0101Craig 0066, 0076, 0101, 0269, 0300Curtis Mathes 0064, 0070, 0089, 0191Cybernex 0269Daewoo 0049, 0074, 0307, 0590Daytron 0049Denon 0071Dynatech 0029Electrohome 0066Electrophonic 0066Emerex 0061Emerson 0029, 0031, 0066, 0072, 0090,

0150, 0213, 0237, 0238, 0241,0307, 0508, 0590

Fisher 0076, 0083, 0133Fuji 0062, 0064Funai 0029GE 0064, 0077, 0089, 0231, 0269Garrard 0029Go Video 0461, 0555

13

SETUP CODES FOR CABLECÓDIGOS DE PROGRAMACIÓN PARA CABLECODES DE PROGRAMMATION DU CÂBLORÉCEPTEUR

ABC 0030, 0032, 0036, 0037, 0040,0042, 0043, 0046

Allegro 0182, 0344Americast 0928Antronix 0051Archer 0051, 0182, 0826Belcor 0085Bell & Howell 0043Bell South 0928Cable Star 0085Cabletenna 0051Cableview 0051Century 0182Citizen 0182, 0344Colour Voice 0054Comtronics 0069Contec 0048Eastern 0031Emerson 0826Everquest 0044, 0069Focus 0429GC Electronics 0085Garrard 0182Gemini 0044, 0826General Instrument 0040, 0305, 0505, 0839GoldStar 0069, 0173Goodmind 0826Hamlin 0038, 0049, 0063, 0288Hitachi 0040Hytex 0036Jasco 0044, 0182, 0344Jerrold 0032*, 0040, 0041, 0043,

0044, 0305, 0505, 0839Magnavox 0056Memorex 0029Movie Time 0092NSC 0092Oak 0036, 0048Optimus 0050Panasonic 0029, 0050, 0136Paragon 0029Philips 0054, 0056, 0182Pioneer 0173, 0562, 0906Popular Mechanics 0429Pulsar 0029Quasar 0029RCA 0050Radio Shack 0044, 0344, 0826, 0912Recoton 0429Regal 0049, 0288Regency 0031

16

* Default code

Proscan 0089, 0231Protec 0101Pulsar 0068Quarter 0075Quartz 0075Quasar 0064, 0191, 1191RCA 0064, 0071, 0077, 0089, 0134,

0135, 0178, 0231, 0269Radio Shack 0029Radix 0066Randex 0066Realistic 0029, 0064, 0066, 0075, 0076,

0077, 0091, 0133ReplayTV 0643, 0645Ricoh 0063Runco 0068STS 0071Samsung 0074, 0269Sanky 0068, 0077Sansui 0029, 0070, 0096, 0238, 0300,

0508Sanyo 0075, 0076, 0133, 0269Scott 0072, 0074, 0150, 0213, 0241Sears 0029, 0064, 0066, 0071, 0075,

0076, 0083, 0133, 0134Semp 0074Sharp 0077, 0091Shintom 0101Shogun 0269Singer 0101Sony 0029, 0061, 0062, 0063, 0064Sylvania 0029, 0064, 0072, 0110Symphonic 0029TMK 0237, 0269Tatung 0070Teac 0029, 0070Technics 0064, 0191Teknika 0029, 0064, 0066Thomas 0029Tivo 0647Toshiba 0072, 0074, 0241Totevision 0066, 0269Unitech 0269Vector 0074Vector Research 0067Video Concepts 0074, 0090Videosonic 0269Wards 0029, 0064, 0071, 0076, 0077,

0089, 0091, 0101, 0110, 0178,0241, 0269

White Westinghouse 0238, 0307XR-1000 0029, 0064, 0101Yamaha 0067Zenith 0029, 0062, 0063, 0068, 0238,

0508

15

SETUP CODES FOR RECEIVERSCÓDIGOS DE PROGRAMACIÓN PARA RECEPTOR.CODES DE PROGRAMMATION DU RÉCEPTEUR.

ADC 0560Adcom 0645Aiwa 0150, 0187, 0218, 0434, 1118,

1434Capetronic 0560Carver 0037, 0071, 0218, 0389, 1118,

1218Casio 0224Clarinette 0224Curtis Mathes 0109Denon 0033, 1133, 1189Emerson 0453Fisher 0071, 0248, 0389Garrard 0453, 0492Harman/Kardon 0139, 0218, 0920JBL 0139JVC 0103Kenwood 0056, 0071, 0106, 0215, 1056,

1342, 1598Koss 0453LXI 0210Linn 0218Lloyd’s 0224MCS 0068, 0375Magnavox 0218, 0224, 0420, 0560, 1118,

1218Marantz 0068, 0218, 1118, 1218Modulaire 0224NAD 0349Nakamichi 0126, 0376Onkyo 0164Optimus 0071, 0109, 0206, 0210, 0215,

0248, 0560, 0699, 0767, 0830,1052

Panasonic 0068, 0338, 1547Penney 0224Philips 0218, 0420, 1118, 1218, 1298Pioneer 0043, 0109, 0179, 0560, 0659,

1052Proscan 1283Quasar 0068RCA 0083, 0375, 0389, 0560, 1283Realistic 0192, 0210, 0224Sansui 0218, 0375, 1118Sanyo 0248, 0830Scott 0192, 0351Sharp 0215Sherwood 0520, 0531Sony 0187, 0503, 1087, 1187, 1287Soundesign 0699Sunfire 1342

18

Rembrandt 0040Runco 0029SL Marx 0069Samsung 0069, 0173Scientific Atlanta 0037, 0046, 0506, 0906Signal 0044, 0069Signature 0040Sprucer 0050Starcom 0032, 0044Stargate 0044, 0069, 0826Starquest 0044Sylvania 0030TV86 0092Tandy 0287Teleview 0069Texscan 0030Tocom 0041, 0042Toshiba 0029Tusa 0044Unika 0051, 0182United Artists 0036Universal 0051, 0085, 0182, 0220Viewstar 0056, 0092, 0287Zenith 0029, 0554, 0928Zentek 0429

SETUP CODES FOR AMPLIFIERSCÓDIGOS DE PROGRAMACIÓN PARA AMPLIFICADOR.

CODES DE PROGRAMMATION DU AMPLIFICATEUR.

Aiwa 0435Carver 0298Curtis Mathes 0329Denon 0189GE 0107Harman/Kardon 0921JVC 0360Linn 0298Magnavox 0298Marantz 0298, 0350Nakamichi 0350Optimus 0329, 0424Panasonic 0337Philips 0298, 0921Pioneer 0042, 0329Realistic 0424Sansui 0350Sony 0249, 0718Soundesign 0107Technics 0337Victor 0360Wards 0042, 0107Yamaha 0383

17

Teac 0192, 0492Technics 0068, 0338, 1337, 1338, 1547Thorens 1218Victor 0103Wards 0043, 0083, 0109, 0187, 0218Yamaha 0205, 0215Yorx 0224Zenith 0886

SETUP CODES FOR DVDCÓDIGOS DE PROGRAMACIÓN PARA DVD.CODES DE PROGRAMMATION DU DVD.

Denon 0519, 0663GE 0551Harman/Kardon 0611JVC 0587, 0652Kenwood 0563Magnavox 0532Marantz 0568Mitsubishi 0550Onkyo 0532, 0656Optimus 0600Panasonic 0519, 0661Philips 0532, 0568Pioneer 0554, 0600, 0661Proscan 0551RCA 0551Samsung 0602Sharp 0659Sherwood 0662Sony 0562Technics 0519Theta Digital 0600Toshiba 0532Yamaha 0519, 0574Zenith 0532, 0620

19

4 function - universal remote control...

Documents