3m twin axial cable assembly for pcie x4 extender … · 2018. 7. 24. · 1 3 78-5100-2521-2 1 1 c...
TRANSCRIPT
1 DIMENSIONS ARE IN MILLIMETERS.
2 3MTM RIBBON TWINAX DESCRIPTION: 30 AWG, SILVER PLATED SIGNAL WIRE IMPEDANCE: 85 5 OHM OVERALL RIBBON WIDTH: 24.90 MM OVERALL RIBBON THICKNESS: 0.75 MM
3 ROHS COMPLIANT. SEE REGULATORY INFORMATION APPENDIX IN "ROHS COMPLIANCE" SECTION AT WWW.3MCONNECTORS.COM (E1 & C1 APPLY)
4 THIS CABLE CONSTRUCTION HAS A THIN ALUMINUM INNER LAYER EXPOSED AT EACH EDGE. USERS SHOULD ASSESS WHETHER THE EXPOSED EDGE PRESENTS A SHORTING RISK IN THEIR SPECIFIC APPLICATION. INSULATING TAPE MAY BE APPLIED AT THE CABLE ASSEMBLY LEVEL, AS NEEDED, TO COVER THE EXPOSED EDGE IN RISK AREAS.
5 APPLICABLE SPECIFICATIONS: PRODUCT SPECIFICATION NUMBER: TWIN AX CABLE: PS-0106 CABLE ASSEMBLY: PS-0137 6 ORDER BY APPLICABLE 3M PART NUMBER: 8KJ1-0727-XXXX
XXXX = DIM 'A' IN MILLIMETERS (1000 = 1 METER)
STANDARD LENGTH (DIM 'A') 8KJ1-0727-0250 (250 MM) 8KJ1-0727-0500 (500 MM)
NON-STANDARD LENGTHS AVAILABLE UPON SPECIAL REQUEST. MAY REQUIRE HIGHER MOQS AND LONGER LEAD TIMES. 150 MM MINIMUM LENGTH.
7 FLAMMABILITY RATING: TWIN AX CABLE: UL94 HB PCBS: UL94V-0 ADHESIVE STRAIN RELIEF: UL94 HB, (TBV)
8 PADDLECARD FINGER GOLD THICKNESS: 0.76 m [30 "] MIN ELECTROLYTIC HARD GOLD OVER 1.27 m [50 "] MIN ELECTROLYTIC NICKEL.
5.54.5
58.0
67.0
27.0
DIM A
SEE NOTE 6
+5-0
15.5
9.0
47.2
8.7
2X 1.57
3MTM TWIN AXIAL CABLE ASSEMBLYFOR PCIe X4 EXTENDER CARD APPLICATIONS
2X CABLE PART NO: 3749-20
2X CABLE PART NO: SL8802/14-18DN5-002X 3.5
ADHESIVE ENCAPSULANTAPPLIED TO CABLE ENDS
ADHESIVE ENCAPSULANTAPPLIED TO CABLE ENDS
NOTES
PART LABEL3M LOGO
3M PART NUMBERDATE CODE: XXYY
XX = YEARYY = WEEK
SIDE A
SIDE B
PIN A1
PIN A32
PIN A1
PIN A32
PIN B1
PIN B32
PIN B1
PIN B32
BILL OF MATERIALSITEM DESCRIPTION QTY
1.0 PBA PCB ASSY, PADDLECARD, PCIE X4 1
1.1 PCB PCIE X4 (64 POS) STRADDLEMOUNT3M P/N: 78-9101-6810-9 1
1.2 CONN CONNECTOR, PCIE 64 POSITION, FEMALESOCKET 1
2.0 PCB PCIE X4 EXTENDER (64 POS) CARD-EDGE3M P/N: 78-9101-6809-1 1
3.0 CABLE RIBBON TWIN AX CABLE3M P/N: SL8802/14-18DN5-00 2
4.0 CABLE RIBBON CABLE, 20 POSITION3M P/N: 3749-20 2
5.0 STRAINRELIEF ADHESIVE AS
REQUIRED
PCIE X4 EXTENDER(64 POS) CARD-EDGE
PCB ASSY, PCIE X4(64 POS) STRADDLEMOUNT
38
3M ELECTRONICS MATERIALS SOLUTIONS DIVISION INTERCONNECT SOLUTIONS http://www.3mconnectors.com
3M IS A TRADEMARK OF 3M COMPANY.FOR TECHNICAL, SALES OR ORDERINGINFORMATION CALL 800-225-5373
12345678
8 7 6 5 4 3 2 1
A
B
C
D D
C
B
A
OFSHTMODEL
SIZE
DET.LISTS
CAGENUMBER
DRAWING NO. REV.
TITLE
3M COPYRIGHTC3M Center
St. Paul,
MN 55144
CHKD DATE APPVL DATE
DRFT DATE MFG DATE
CHKDDRFTREV ECO ISSUE DATE AND DESCRIPTION
DR
AW
ING
NU
MB
ER
RE
VIS
ION
ACCESSCODES
DESIGN REFERENCE NEXT ASSEMBLY
DIVISION DIVISION CODE
TOLERANCESEXCEPT AS
NOTED
DO NOTSCALE
DRAWING
SCALE
MILLIMETERS
INCHES
.0000
.000
.00
.0
0 .0 .00 .000
ANGLES
THIRD ANGLE PROJECTION
INTERPRET PERASME Y14.5 - 2009
MAX SURFACE ROUGHNESS
ALL SURFACES
MARKED ONLY NOYES
This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved.
.005
.05
.51
8KJ1-0727-XXXX, CABLEASSY, PCIE X4 BY PCIE
X4 EXTENDER
12531
78-5
100-2
521-2
11
D
D78-5100-2521-2
L SCHMIDT APR 09,2012
2019
T SUNIGA APR 23,2019
1
INITIAL RELEASE
A 40795 JUN 18,2012 LDS TS
REVISED NOTE 6
B 42467 AUG 06,2012 LDS TS
ADDED URL ANDTRADEMARK NOTES SH1,ZONE A8; ADDED SH3,WARRANTY INFO NOTES;ADDED NOTE TO CLARIFYPINOUTS, SH2, ZONEA2,3
C 77066 DEC 20,2017 AD LS
REVISED PART LABEL
D 84237 APR 23,2019 LDS TS
Imaged: C
en
tra
l S
tan
da
rd T
ime 5
/15
/20
19 --
UT
C O
ffset (h
rs)
6
3M 3749-20 CableWire # Pin Attachment #
01 Ground Layer02 B01 - B0203 B01 - B0204 B01 - B0205 B01 - B0206 B01 - B0207 B01 - B0208 Ground Layer09 B0510 B0611 Ground Layer12 B0813 B0814 B0915 B1016 B1017 Ground Layer18 B1119 Ground Layer20 B12
3M SL8802 CableWire # Pin Attachment #
GND Ground Layerpr_01 B14pr_01 B15pr_02 B17pr_02 Ground Layerpr_03 B19pr_03 B20pr_04 B23pr_04 B24GND Ground Layerpr_05 B27pr_05 B28pr_06 Ground Layerpr_06 Ground Layerpr_07 B30pr_07 B31GND Ground Layer
PCI-Express X4 Pin-OutPin # Side B Description Side A Description Pin #
B01 +12 volt power Hot plug presence detect A01B02 +12 volt power +12 volt power A02B03 +12 volt power +12 volt power A03B04 Ground Ground A04B05 SMBus clock TCK A05B06 SMBus data TDI A06B07 Ground TDO A07B08 +3.3 volt power TMS A08B09 +TRST# +3.3 volt power A09B10 3.3v volt power +3.3 volt power A10B11 Link Reactivation Power Good A11
Mechanical KeyB12 Reserved Ground A12B13 Ground Reference Clock A13B14 Transmitter Lane 0, Differential pair A14B15 Differential pair Ground A15B16 Ground Receiver Lane 0, A16B17 Hotplug detect Differential pair A17B18 Ground Ground A18B19 Transmitter Lane 1, Reserved A19B20 Differential pair Ground A20B21 Ground Receiver Lane 1, A21B22 Ground Differential pair A22B23 Transmitter Lane 2, Ground A23B24 Differential pair Ground A24B25 Ground Receiver Lane 2, A25B26 Ground Differential pair A26B27 Transmitter Lane 3, Ground A27B28 Differential pair Ground A28B29 Ground Receiver Lane 3, A29B30 Reserved Differential pair A30B31 Hot plug detect Ground A31B32 Ground Reserved A32
3M 3749-20 CablePin Attachment # Wire #
Ground Layer 01A01 02Ground Layer 03A02 - A03 04A02 - A03 05A02 - A03 06A02 - A03 07Ground Layer 08A05 09A06 10A07 11A08 12Ground Layer 13A09 - A10 14A09 - A10 15A09 - A10 16A09 - A10 17Ground Layer 18Ground Layer 19A11 20
3M SL8802 CablePin Attachment # Wire #
Ground Layer GNDA13 pr_01A14 pr_01A16 pr_02A17 pr_02Ground Layer pr_03A19 pr_03A21 pr_04A22 pr_04Ground Layer GNDA25 pr_05A26 pr_05A29 pr_06A30 pr_06A32 pr_07Ground Layer pr_07Ground Layer GND
THIS IS A FEED THROUGH ASSEMBLY. THE PIN ASSIGNMENTS REMAIN THE SAME ON BOTH ENDS.
12345678
8 7 6 5 4 3 2 1
A
B
C
D D
C
B
A
OFSHTMODEL
SIZE
DET.LISTS
CAGENUMBER
DRAWING NO. REV.
TITLE
3M COPYRIGHTC3M Center
St. Paul,
MN 55144
CHKD DATE APPVL DATE
DRFT DATE MFG DATE
CHKDDRFTREV ECO ISSUE DATE AND DESCRIPTION
DR
AW
ING
NU
MB
ER
RE
VIS
ION
ACCESSCODES
DESIGN REFERENCE NEXT ASSEMBLY
DIVISION DIVISION CODE
TOLERANCESEXCEPT AS
NOTED
DO NOTSCALE
DRAWING
SCALE
MILLIMETERS
INCHES
.0000
.000
.00
.0
0 .0 .00 .000
ANGLES
THIRD ANGLE PROJECTION
INTERPRET PERASME Y14.5 - 2009
MAX SURFACE ROUGHNESS
ALL SURFACES
MARKED ONLY NOYES
This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved.
.005
.05
.51
8KJ1-0727-XXXX, CABLEASSY, PCIE X4 BY PCIE
X4 EXTENDER
12532
78-5
100-2
521-2
11
D
D78-5100-2521-2
L SCHMIDT APR 09,2012
2019
T SUNIGA APR 23,2019
1
INITIAL RELEASE
A 40795 JUN 18,2012 LDS TS
REVISED NOTE 6
B 42467 AUG 06,2012 LDS TS
ADDED URL ANDTRADEMARK NOTES SH1,ZONE A8; ADDED SH3,WARRANTY INFO NOTES;ADDED NOTE TO CLARIFYPINOUTS, SH2, ZONEA2,3
C 77066 DEC 20,2017 AD LS
REVISED PART LABEL
D 84237 APR 23,2019 LDS TS
3M ELECTRONICS MATERIALS SOLUTIONS DIVISION INTERCONNECT SOLUTIONS http://www.3mconnectors.com
3M IS A TRADEMARK OF 3M COMPANY.FOR TECHNICAL, SALES OR ORDERINGINFORMATION CALL 800-225-5373 Im
aged: C
en
tra
l S
tan
da
rd T
ime 5
/15
/20
19 --
UT
C O
ffset (h
rs)
6
Regulatory: For regulatory information about this product, visit 3M.com/regsor contact your 3M representative.
Technical Information: The technical information, recommendations and otherstatements contained in this document are based upon tests or experience that3M believes are reliable, but the accuracy or completeness of such informationis not guaranteed.
Product Use: Many factors beyond 3M's control and uniquely within user's controlcan affect the use and performance of a 3M product in a particular application.Given the variety of factors that can affect the use and performance of a3M product, user is solely responsible for evaluating the 3M product anddetermining whether it is fit for a particular purpose and suitable for user'smethod of application.
Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty isspecifically stated on the applicable 3M product packaging or product literature,3M warrants that each 3M product meets the applicable 3M product specification atthe time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS,EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY ORCONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIEDWARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OR TRADE.If the 3M product does not conform to this warranty, then the sole and exclusiveremedy is, at 3M's option, replacement of the 3M product or refund of the purchaseprice.
Limitation of Liability: Except where prohibited by law, 3M will not be liable forany loss or damage arising from the 3M product, whether direct, indirect, special,incidental or consequential, regardless of the legal theory asserted, includingwarranty, contract, negligence or strict liability.
3M Electronics Materials Solutions Division6801 River Place Blvd.Austin, TX 78726-9000 1-800-225-5373www.3M.com/interconnect
12345678
8 7 6 5 4 3 2 1
A
B
C
D D
C
B
A
OFSHTMODEL
SIZE
DET.LISTS
CAGENUMBER
DRAWING NO. REV.
TITLE
3M COPYRIGHTC3M Center
St. Paul,
MN 55144
CHKD DATE APPVL DATE
DRFT DATE MFG DATE
CHKDDRFTREV ECO ISSUE DATE AND DESCRIPTION
DR
AW
ING
NU
MB
ER
RE
VIS
ION
ACCESSCODES
DESIGN REFERENCE NEXT ASSEMBLY
DIVISION DIVISION CODE
TOLERANCESEXCEPT AS
NOTED
DO NOTSCALE
DRAWING
SCALE
MILLIMETERS
INCHES
.0000
.000
.00
.0
0 .0 .00 .000
ANGLES
THIRD ANGLE PROJECTION
INTERPRET PERASME Y14.5 - 2009
MAX SURFACE ROUGHNESS
ALL SURFACES
MARKED ONLY NOYES
This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved.
.005
.05
.51
8KJ1-0727-XXXX, CABLEASSY, PCIE X4 BY PCIE
X4 EXTENDER
12533
78-5
100-2
521-2
11
D
D78-5100-2521-2
L SCHMIDT APR 09,2012
2019
T SUNIGA APR 23,2019
1
INITIAL RELEASE
A 40795 JUN 18,2012 LDS TS
REVISED NOTE 6
B 42467 AUG 06,2012 LDS TS
ADDED URL ANDTRADEMARK NOTES SH1,ZONE A8; ADDED SH3,WARRANTY INFO NOTES;ADDED NOTE TO CLARIFYPINOUTS, SH2, ZONEA2,3
C 77066 DEC 20,2017 AD LS
REVISED PART LABEL
D 84237 APR 23,2019 LDS TS
3M ELECTRONICS MATERIALS SOLUTIONS DIVISION INTERCONNECT SOLUTIONS http://www.3mconnectors.com
3M IS A TRADEMARK OF 3M COMPANY.FOR TECHNICAL, SALES OR ORDERINGINFORMATION CALL 800-225-5373 Im
aged: C
en
tra
l S
tan
da
rd T
ime 5
/15
/20
19 --
UT
C O
ffset (h
rs)
6