3ft antenna su3-w71 feed installation (nmt534-00)
TRANSCRIPT
![Page 1: 3ft Antenna SU3-W71 Feed Installation (NMT534-00)](https://reader036.vdocuments.mx/reader036/viewer/2022073120/55cf9925550346d0339bd989/html5/thumbnails/1.jpg)
Sales department : Radio Frequency Systems GmbHKabelkamp 20, D-30179 Hannover (Germany) •Tel. +49-511 676-25 20 •Fax +49-511 676-25 21
Plant: RFS France Trignac •Fax +33 02 40 90 41 43 1/3
Feed Installation Instructions3 ft Antennas (with E-Mount)DA, UA, SU, SD, DAXUDA, UXA, SUX, SDX NMT 534-00(e)
1. Recommendations
2. Feed disassembly
3. Antenna orientation depending of antenna offset
Cardboard
Cardboard
The feed is a precision component which should be handled with special care duringinstallation. For instance, always carry the feed, supporting casting plate side. Anydamage may degrade the antenna’s performance. Repair of feeds is not possible inthe field.
- Dismount the front part of thefeed system (pre-assembled infactory).
- Hold the antenna in the correct orientation depending of the offset to the Left or Right of thesupport pipe on the tower.
Antenna orientationfor an Offset Left
Antenna orientationfor an Offset Right
Depending of frequency, a tuningplate maybe pre-installed, (you
do not need to removed it).
Front part of thefeed system
Rear part of thefeed system
Remove the 4socket screws M4
with SL washers A4to split the feed
system in 2 parts(Front & Rear)
![Page 2: 3ft Antenna SU3-W71 Feed Installation (NMT534-00)](https://reader036.vdocuments.mx/reader036/viewer/2022073120/55cf9925550346d0339bd989/html5/thumbnails/2.jpg)
NMT 534-00e 2/3
4. Feed orientation for monopolarized feed system
5. Feed orientation for dualpolarized feed system
6. Feed system installation
HorizontalPolarization
VerticalPolarization
AntennaTOP
AntennaTOP
HorizontalPolarization
VerticalPolarization
Output IEC Flange Output IEC Flange+ N Transition
AntennaTOP
- Install the rear part ofthe feed system usingthe 4 socket screwsM5 with washers, onthe reflector castingring
4 screws M54 sl washer A54 washers 5.3 Ø15
Rear part
Reflectorcasting ring
![Page 3: 3ft Antenna SU3-W71 Feed Installation (NMT534-00)](https://reader036.vdocuments.mx/reader036/viewer/2022073120/55cf9925550346d0339bd989/html5/thumbnails/3.jpg)
NMT 534-00e 3/3
7. Feed polarization adjustment (to do after antenna installation on tower pipe)
8. Next instructions (refer to main installation instructions)
- Install the front part of the feed onthe rear part, with the 4 M4 screws(refer to the previous pages forfeed‘s system polarization)
4 socket screws M44 sl washers A4
Front part of the feed system (if the feed isequipped with a tuning plate, you do not needto remove it)
Take care to notbrake the mylar
obturation
±5° P
olar
. Adjust.
±5° Polar
. Adj
ust.
±5° P
olar
. Adjust.
±5° Polar
. Adj
ust.
- Loosen the 4 screws M5- Adjust polarization ± 5°- Tighten the 4 M5 screws
Monopolarization Dual polarization
M5 screws M5 screws