36 / 36 3f user manual - tanning-bed-parts.comtanning-bed-parts.com/documents/ets tan...

36 / 36 3F

USER MANUAL 23596-01A

23596-01A

i

Limited Lifetime Warranty

Solaris™ warrants your tanning unit to be free of structural defects in its material andworkmanship, under normal use, for its lifetime. Solaris will repair or replace, at their dis-

cretion, any defect to the structure which affects the performance of the unit.

For 6 months from the date of purchase, Solaris will provide replacements for parts thatprove to be defective in material or workmanship. Acrylic shields, fluorescent lamps, and

lamp starters are excluded from this warranty. Labor will be covered for 30 days from pur-chase date. Normal wear, damage from misuse or abuse, damage incurred in transit, or

damage done by unauthorized repairs or modifications are not covered by this warranty.

ETS, Inc. disclaims any implied warranty of merchantability or fitness for any periodbeyond the expressed warranty. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitations may not apply to you.

No one has authority to change or modify this Limited Lifetime Warranty in any respect. Toobtain service under the Limited Lifetime Warranty, contact ETS, Inc. at 1-800-449-3605

and ask for the Technical Service Department.

ETS, Inc. shall not be liable for loss of use, loss of time, inconvenience, rental or substituteproducts, loss of business, loss of income, or any other incidental or consequential damages.Some states do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which mayvary from state to state.

All warranty service must be performed by an authorized service person. If your tanningunit must be returned for service, all freight charges must be at your expense. Contact your

place of purchase for the address of the Solaris Service Center nearest you. Proof of pur-chase is required to obtain warranty service.

This warranty covers the original purchaser only. This warranty is void if the unit is modi-fied in any manner from its original design.

2359

6-01

A ii

elcomeCongratulations on your purchase of this technologically advanced sun tanning unit. It has beendesigned to provide years of dependable service for you.

Please read all the instructions in this booklet before installing and using the unit. Always be sure toobserve all safety precautions.

ontentsSafety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Pre-Installation Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Hardware Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Assembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Remote Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Before You Tan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Exposure Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Using Your Sunbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Cleaning After Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Thorough Periodic Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Mechanical Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Lamp and Acrylic Replacement . . . . . . . . . . . . . . . . . . . . . . . . .19

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

23596-01A

Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexposure cancause eye and skin injury and allergic reactions. Repeated exposure may cause premature aging of the skin

and skin cancer. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THEEYES. Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before using sunlamp ifyou are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight. If you do not tan inthe sun, you are unlikely to tan from the use of this product.

To use, lie down under canopy and pull down as far as adjustment will allow. Minimum use distance from face tanner is 1 inch or 2.54centimeters. Minimum use distance elsewhere is touching the clear plastic panels. Do not use without clear plastic panels in place.Untanned persons should not tan on consecutive days during their first week of tanning. Never tan more than once a day. Tanningnormally appears after the first few sessions and maximizes after approximately four weeks. Tan once or twice per week thereafter tomaintain appearance. Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan.

New lamps emit approximately 10% more ultraviolet radiation during the first 50 hours of operation. Recommended tanning timesshould therefore be reduced by approximately 10% during that period.

WARNING: • Read the instructions booklet before using this sunlamp product. • All persons in the room should wear protectiveeyewear when lamps are on. Recommended eyewear: provided eyeshields (Lucas Products Super Sunnies or Intrexco No. 5635/1) orequivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewear may not provide adequate protection.

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:Model 36: SPEED™ 175 Wolff® Model SPD75-T12 Bi-Pin

Model 36 3F: SPEED™ 175 Wolff® Model SPD75-T12 Bi-PinPhilips Model HPA 400/30s or CosmoTech Model 23045 or 20046 (facial unit)

THIS EQUIPMENT MUST BE EARTH GROUNDED.

THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER 21 CFR PART1040.20

iii

afety InformationLABELING NOTICE: Labels are affixed on all systems to inform the user of possible dangers. Regulations are stated in 21 CFR, Section1040.20, and require that all products manufactured after September 8, 1986 which use sunlamps must display the following:

DANGER

RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTESLevel 1/Week 1 Level 2 Level 3 Level 4 Subsequent

Skin Type: 1st-3rd Sessions MaximumI Sensitive Skin (Burns easily and severely and does not tan.) NOT RECOMMENDED FOR TANNINGII Light (Burns easily and severely and tans minimally.) 4 8 12 16 20III Normal (Burns moderately and tans average.) 6 10 15 20 20IV Dark (Burns minimally, tans easily and above average.) 8 12 16 20 20

DISCONNECT POWER CORD BEFORE ATTEMPTING TO CLEAN, RELAMP, OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT.

2359

6-01

A 1

nstallation

Unpacking and Inspection

Your sunbed comes in two cardboard car-tons, one for the canopy and one for thebench and ballast tray. Open the cartonsand remove the sunbed parts as follows.

The bench and canopy are each wrappedin plastic. Pull back the plastic and, witha helper, grasp the canopy and pull it fromthe carton bottom, leaving the plasticwrap and the carton packaging. Do thesame for the bench. Do not attempt to lifteither unit with the plastic still on as itmay slip. Do not lift the canopy by itsplastic endcaps. The ballast tray is securedto the carton bottom with brackets.Remove these brackets from the ballasttray with a Phillips screwdriver.

Note! The cartons are reusable, in theunlikely event that you may find it neces-sary to return your sunbed.

After unpacking the unit, check to makesure you have received the following:

• Canopy unit• Bench unit• Ballast tray• Metal access panel (with logo)• Long metal hinge cover panel• Two large endcaps• Bag containing necessary assembly

hardware, safety goggles, and pillow.

Inspect these items, including the canopyand bench, to make sure they are freefrom any visible damage. Report theextent of any damage to the transportationcompany.

Record the serial numbers of the canopyand bench, and the ballast tray ID numberin the area provided on the back of thismanual. This information will be requiredwhenever you call customer service.

23596-01A

2

Installation - Tools Required

Tools RequiredYou will need the following tools to assemble your sunbed.

#2 Phillips Screwdriver

Adjustable Wrench

9/16” Wrench

5/16” Allen Wrench

2359

6-01

A 3

Installation - Pre-Installation Planning

Pre-Installation PlanningBefore you begin to assemble your sunbed, you should observe the following consid-erations.

• Your sunbed operates from a 220VAC power source. The unit should bewired to a dedicated circuit asdescribed below. We recommendconnection by a professional electri-cian.

• IMPORTANT! Voltage must bebelow 230V AC or may require aBuck Booster. Contact ETS service atthe number on the back of this man-ual. Use of a voltage source above230V AC may reduce the life ofsome components in your sunbed.

• The Solaris™ 36 Speed™ 175System requires a dedicated circuitcapable of providing 30 Amp service.The Solaris™ 36 3F Speed™ 175System requires a dedicated circuitcapable of providing 40 Amp service.This unit must be hardwired directlyto a junction box.

• Make sure the room in which youintend to use your sunbed is wellventilated. Air from the room is usedto cool the sunbed, and a poorlyventilated room may cause the unitto become hot and cause discomfortto the user.

• Your sunbed is designed to operatein an ambient room temperature of80°F maximum and 70% relativehumidity.

• Place your sunbed no closer than 6"from any wall. Make sure that cur-tains, drapes, and other room furni-ture do not obstruct the airflow intoor out of the fan opening areas.

• Proper assembly of your sunbedrequires three people. Plan to have acouple of helpers assist you.

23596-01A

4

Installation - Hardware Inventory

Hardware Inventory

Open the hardware bag and remove thehardware. Make sure you have the follow-ing hardware items.

Safety GogglesQuantity 1

Access Panel KeyQuantity 1

#10 x 1” PhillipsPan Head Screw

Quantity 14

3/8-16 x 1 1/4”Hex Socket Bolt

Quantity 6

3/8-16 Self-lockingHex Nut

Quantity 6

#10 x 1/2” PhillipsPan Head Screw

Quantity 4

2359

6-01

A 5

Installation - Assembly Procedures

Assembly Procedures

Before installing the foot end endcap youmust install the body fan power cord intothe endcap, as shown below. The connec-tor will snap securely into the endcap. Thebody fan kit includes instructions forinstallation.

BODY FAN POWER CORD

Snap body fan powercord into hole in footend endcap.

23596-01A

6


Parts needed:Head end endcapFoot end endcap14 - #10 x 1” Phillips pan-head screws4 - #10 x 1/2” Phillips pan-head screws

Attach each endcapwith 7 - 1” screwsas shown.

Foot end endcapshown.

Use 1/2” screws here.

2359

6-01

A 7


Use the preinstalledscrews to attach thehinge cover panel.

Parts needed:Long blue hinge cover panel

23596-01A

8


Install this bolt as apositioning aide.

Slip canopy arm onto hingearm. Positioning bolt willengage the slot on top ofhinge arm and hold canopyup while the other bolts areinstalled.

Install other bolts asshown. Secure all sixbolts in place with self-locking nuts.

Parts needed:6 - 3/8 x 1 1/4” hex-socket bolts6 - 3/8” self-locking hex nuts

CANOPY ARM

HINGE ARM

Remove this pinand discard.

2359

6-01

A 9


Slide ballast trayunder and pull cordsthrough to the back.

Put access panel inplace and lock withaccess panel key.

Install Body Fan.Instructions areincluded in BodyFan kit.

23596-01A

10

Installation - Electrical Connections

Electrical ConnectionsAt the rear of the sunbed, connect the twocanopy power cords and two bench powercords from the ballast tray to their respectivepower receptacles. Simply match the plugto the receptacle, push on firmly and secureby twisting the threaded locking ring. TheRemote Control Bypass plug is installed in aremote control port. Your sunbed will notoperate without the Remote Control Bypassplug or a remote system connected.Connect main power cord as described inPre-Installation Planning.

NOTE: Your sunbed is designed to accept aninput from a remote control device. Theremote control is optional. If you plan on usinga remote system refer to Remote Connections.

ATTENTION: Although the Remote ControlBypass plug provided with your sunbed willwork wherever a T-Max® terminator is calledfor in the series, the T-Max® terminator willnot work as a bypass plug. Normally, a bypassplug is needed only when your sunbed is oper-ated without a remote system connected.

REAR OF BALLAST TRAY

CANOPY POWER RECEPTACLES

BENCH POWER RECEPTACLES

MAIN POWER CORD

RemoteControl Bypass

plug

Remote Ports

CONNECT LAST CONNECT FIRST

2359

6-01

A 11

Installation - Final Adjustments

LIFT ADJUSTMENT

MAINTENANCE HEIGHT RELEASE HANDLE

HOUR COUNTER

AIR FILTERS

Final Adjustments

Your sunbed uses a smooth gliding springlift system to raise the canopy. This lift sys-tem may need to be adjusted slightly dueto shipment. Remove the front accesspanel. Use a wrench to turn the hexshaped Lift Adjustment lugs (shownbelow), clockwise for more lift and coun-terclockwise for less. When adjustedproperly, the canopy should raise easily aswell as rest fully closed. Always adjustboth lugs equally.

Make sure the air filters are in place. Thefilter on top of the ballast tray simply sitsover the vent holes. Airflow holds it inplace when the unit is on. The airflowarrow on the side of this filter should pointdown. The filter hanging under the benchshould be installed with the arrow point-ing up.

LIFT ADJUSTMENT

23596-01A

12

Installation - Remote Connections

Remote Connections

Your sunbed incorporates advanced circuitryallowing it to connect and communicate withmost remote control systems. If a remote sys-tem is to be used, first determine whether theremote system is a T-Max® System or a stan-dard remote system operating with a controlrelay. Follow the appropriate instructions foryour system type.

Warning: The remote connection is notdesigned to supply or accept high voltage, norcan it provide power to an external timer. Thesunbed’s remote interface circuitry operateson 5 volts, attempting to connect it to anyhigher voltages will damage the sunbed aswell as void your warranty.

T-Max® ProductsThe T-Max® remote systems offer the ultimatein sunbed control, while allowing the tannereasy straightforward operation. Your sunbed isconfigured to directly connect to this system.The circuitry inside your sunbed eliminatesthe need for the T-Max® 1A or 3A when con-necting to the T-Max® Manager series. Yoursunbed supports the auto addressing featureof the latest T-Max® Manager models and thefollowing parameters: 2, 5, 6, 7, 8, 9, 10, 14,and 15. See your T-Max® manual for descrip-tions of these parameters and how they func-tion.

T-Max® Manager Remote System This system is ideal for multiple sunbed instal-lations. Simply connect the RJ-22 modularcable(s), described in the T-Max® Managermanual, into the remote port(s) located on theback of your sunbed and follow the instruc-

tions that came with your remotesystem, noting figure 1. If you havean older T-Max® Manager that does-n’t support auto addressing, set theaddress, or “id”, of each sunbedmanually as described in Setting theaddress manually. You can placeyour sunbed at any location in theseries.

figure 1

NOTE: A T-Max® 1Acan be substituted for

the 3A in figure 1.

2359

6-01

A 13

T-Max® 1A and 3A Remote SystemsThe T-Max® 1A and 3A offer the same controlas the T-Max® Manager in single sunbed instal-lations. If you’re using a 1A, it must have a chiplabelled “master” installed on its circuit board.The remote control bypass plug must not beused in this configuration.

After you have set the T-Max® 1A’s, or 3A’s,address to “0” (refer to your T-Max® user’sguide) and the sunbed’s address to “1” (seeright), simply connect the RJ-22 modularcables, described in the T-Max® user’s guide,directly into either port located on the back ofthe sunbed and either port on the back of theT-Max® 1A or 3A. See figure 2.

Setting the address manuallyBefore connecting your sunbed to the T-Max®Manager or T-Max® 1A or 3A, the address ofyour sunbed must first be set. Set the “id” man-ually as described below.

Setting the “id” 1. Make sure no cables are plugged into

your sunbed’s remote ports.2. Remove and reapply power to the unit.3. Press and hold the stop button, located

on the sunbed display, for three secondsand release. The display should indicatean “id” number from “oF” to “252”.

4. If you are using a T-Max® 1A or 3A asyour remote, the “id” of the sunbedmust be set to “1”. If you are using a T-Max® Manager each sunbed must beassigned a different “id”. To set the “id”press the timer button, to count up, orthe body fan control button, to countdown, until the desired number isachieved.

5. Press the stop button to return to thenormal display mode.

1-99

100-199

200-252

figure 2


NOTE: A T-Max® 1Awith a “master” chipcan be substituted for

a 3A in figure 2.

23596-01A

14

figure 3

Remote systems using a Control Relay

Most non-T-Max® remote systems control thesunbed by the use of a relay. The relay oper-ates the sunbed by connecting and discon-necting a pair of wires leading from thesunbed. Refer to the user’s manual providedwith your remote system to determine if itoperates in this way. To connect your sunbedto this type of system a remote interface kit isrequired. Call ETS at the phone number listedon the back of this guide to obtain the kit.Figure 3 details a typical connection. Followthe instructions provided with the kit andfrom the remote’s manual to make the neces-sary connections.


2359

6-01

A 15

peration

Before You Tan

Before using your sunbed, please note thefollowing important precautions.

• Your skin should be free of cosmetics,tanning oils, or other body lotionsprior to tanning except for thosespecifically made for use with tanningdevices. However, do not remove nat-ural body oils by bathing or showeringimmediately before tanning.

• Your hair should be free of gels,mousses, sprays, or other hair productsprior to tanning. These products cancause damage to the sunbed acrylic.As an alternative, a shower cap ortowel may be worn to keep treated hairaway from the sunbed surfaces.

• As with all electrical appliances, donot operate this device near water orwhile you are wet.

RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTESLevel 1/Week 1 Level 2 Level 3 Level 4 Subsequent

Skin Type: 1st-3rd Sessions MaximumI Sensitive Skin (Burns easily and severely and does not tan.) NOT RECOMMENDED FOR TANNINGII Light (Burns easily and severely and tans minimally.) 4 8 12 16 20III Normal (Burns moderately and tans average.) 6 10 15 20 20IV Dark (Burns minimally, tans easily and above average.) 8 12 16 20 20

• Some medication may increase yoursensitivity to ultraviolet light. It is rec-ommended that you consult a physi-cian before using this sunbed if takingany medication or if you suspect thatyour skin might be especially sensitiveto sunlight. Included with this manualis an FDA booklet on medications thatincrease sensitivity to light.

Exposure Times

Follow the guidelines for skin type andexposure times as shown in the tablebelow. Untanned persons should not tanon consecutive days during their first weekof tanning. Never tan more than once aday. Tanning normally appears after the firstfew sessions and maximizes after approxi-mately four weeks. Tan once or twice perweek thereafter to maintain appearance.Persons already having a base tan maybegin at advanced levels corresponding tothe extent of their base tan.

23596-01A

16

Operation - Using Your Sunbed

1. Lift canopy, lie down on bench (face up),lower canopy toward your body usingcanopy handle. For best results, positioncanopy as close to your body as possible.

2. Put on your safety goggles.

3. Assuming the remote system has been setto allow a pre-tanning delay time, the timerdisplay (E) will repeatedly flash the delaysymbol “dL” and then the remaining delaytime. Press the timer button (G) or waituntil the delay time has expired to beginthe tanning session. The lamps will turn onand the timer will begin to count down.

4. When the timer reaches 0 the lamps turn off.If you want to interrupt your session beforetime expires, press the stop button (F).

5. Raise the canopy by using the canopyhandle, do not push up on the acrylicshield. The cooling fans run for three min-utes after the lamps shut off to aid in cool-ing the sunbed. The timer will indicate “..”as a reminder to clean the sunbed. Afterthe sunbed is cleaned press the timer but-ton and the display will return to “0”.

Using Your SunbedWhen connected to the T-Max® Manager or T-Max® 1A or 3A.

A Face tanner control - Turns face tannerson and off during use. (Units equippedwith face tanner only)

B Body tanner control - Turns body lampson and off during use. (Units equippedwith face tanner only)

C Body fan control - Controls the speed ofthe body fan during use.

D Body fan speed indicator - Indicatesspeed of fan. (OFF - LOW - MED -HIGH)

E Timer display - Displays remaining time.

F Stop button - Interrupts tanning session.

G Timer button - Turns bed on. Timer dis-play shows remaining time. If a lessertime is desired, press timer button untildesired time is displayed.

A B C D E F G

2359

6-01

A 17

Using Your SunbedWhen used as a stand alone unit or when connected to a remote system using a control relay.

1. Lift the canopy, lie down on the bench(face up), lower the canopy toward yourbody using the canopy handle. For bestresults, position the canopy as close toyour body as possible.

2. Put on your safety goggles.

3. Press the timer button (G) to begin the tan-ning session. The lamps will turn on andthe timer will begin to count down.

4. If a tanning time less than the displayedtime is desired repeatedly press the timerbutton (G) to decrease the remaining time.

5. When the timer reaches 0 the lamps turnoff. If you want to stop your session beforetime expires, press the stop button (F). Youwill have ten seconds to restart with theremaining time, otherwise the timer willreset to 0.

6. Raise the canopy by using the canopyhandle, do not push up on the acrylicshield. The cooling fans run for three min-utes after the lamps shut off to aid in cool-ing the sunbed.

A B C D E F G

A Face tanner control - Turns face tannerson and off during use. (Units equippedwith face tanner only)

B Body tanner control - Turns body lampson and off during use. (Units equippedwith face tanner only)

C Body fan control - Controls the speed ofthe body fan during use.

D Body fan speed indicator - Indicatesspeed of fan. (OFF - LOW - MED -HIGH)

E Timer display - Displays remaining time.

F Stop button - Stops tanning session.

G Timer button - Turns bed on. Timer dis-play shows remaining time. If a lessertime is desired, press timer button untildesired time is displayed.

Operation - Using Your Sunbed

23596-01A

18

are and Maintenance

Cleaning After Use

Clean and disinfect your tanning bed’sbench and canopy after each use. Use anon-abrasive disinfectant cleaner that doesnot contain ammonia or ammonia deriva-tives. Ammonia may damage the acrylicshield. Spray the acrylic lightly with disin-fectant and wipe dry with a clean soft cloth.We recommend SunQuest® disinfectant andSunQuest® acrylic cleaner.

Thorough Periodic Cleaning

IntroductionThe cooling fans draw air through the bedand over time will cause a dust buildup onthe lamps and reflectors. This will reducethe tanning effectiveness of the bed. Whena dust buildup is observed, it is necessary tothoroughly clean the inside of the benchand canopy. Warning! Disconnect sunbedfrom electrical power before cleaning.

Cleaning the Canopy and BenchStep 1 Remove the acrylic shields and

lamps as described in Lamp andAcrylic Replacement.

Step 2 With a soft cloth, wipe the entirelength of each lamp to removeany film buildup.

Step 3 Clean both sides of the acrylic

shields with a non-ammonia dis-infectant cleaner.

Step 4 Wipe the reflectors with a cleandamp cloth.

Step 5 Reinstall the lamps and acrylicshields.

Step 6 Clean or replace air filters on topof ballast tray and under bench(see Final Adjustments). Replacewith 10” x 24” x 1” furnace filters.

Mechanical Inspection

Your tanning bed has been built for years ofservice. To ensure trouble-free operationthroughout its life, inspect the unit’smechanical integrity every 400-500 hoursof use.

• Inspect the unit’s fasteners verifyingthat all are firmly in place.

• Inspect lift springs for signs of wear.Adjust for proper lift if needed. SeeFinal Adjustments.

• Inspect the AC power cord and itsconnections.

• Inspect the acrylic. Broken, cracked orbadly scratched acrylics should beimmediately replaced.

• Check damper operation. The damperlimits the canopy’s movement speed.Replace every 16,000 hours or ifcanopy raises and lowers too quickly.

2359

6-01

A 19

Care and Maintenance - Lamp and Acrylic Replacement

Lamp and Acrylic Replacement

IntroductionTo be assured of maximum tanning effec-tiveness, change lamps after approximate-ly 800-1000 hours of use. Tanning willcontinue after this time but at a slowerrate. To ensure trouble-free operation ofyour sunbed, replace the lamp starterswhenever the lamps are replaced.

Warning! Disconnect sunbed from elec-trical power before servicing.

Maintenance Height FeatureThe Solaris™ 36 offers a convenience fea-ture when maintenance must be per-formed. Behind the front access panel is arelease handle (see Final Adjustments).With the canopy open, pull this handleand the canopy will raise to its mainte-nance position, allowing easier access tolamps, etc. When finished, simply closethe canopy to return to normal operation.

Opening/Replacing Acrylic ShieldsThe acrylic shield in the bench is securedin place by a plastic profile across thefront ledge of the bench. Simply pry up onthe inside edge of the profile until itreleases its latching action (see illustrationnext page). The profile will then separatefrom the bed. The aluminum framearound the acrylic offers support as wellas allowing the acrylic to hinge openwithout removing it from the bed.Standing in front of the bed, lift the longedge of the acrylic. On the inside of thebench, along the front, are two supportsfor the bench acrylic. Release them fromtheir clips and swing up to hold theacrylic open. You may remove the acrylicby lifting it out of its hinge channel alongthe back edge.

The canopy acrylic is held in place by fourturn latches along the front edge. Use aflat-bladed screwdriver to turn the latchesa quarter turn to open the acrylic. Thecanopy acrylic also swings open on ahinge and may be removed by lifting it outof the channel along the back edge.

When you are finished, simply reverse theabove directions to secure the acrylicshields. Make sure the profile on thebench snaps back in place.

23596-01A

20


CANOPY ACRYLIC

BENCH ACRYLIC

ACRYLIC SUPPORT PROFILE

Body fan deleted for clarity.

2359

6-01

A 21


Removing/Replacing LampsAfter removing the acrylic shield, replacelamps as follows.

Step 1 Grasp the lamp at one end andat the middle and turn the lampone quarter turn. Gently removethe lamp from its holders.

Step 2 Reinstall the lamp by insertingthe pins located on the ends ofthe lamp into the slots on top ofthe lamp holders and turn thelamp a quarter turn. It shouldclick in place.

Recommended Replacement LampsWe recommend using the lamps specifiedbelow. Use of uncertified lamps is a viola-tion of Federal regulations and will voidyour warranty. These lamps have an aver-age life of 800-1000 hours of effectivetanning use. Lamps used longer than thatbegin to lose their effectiveness eventhough they continue to light.

Recommended Replacement AcrylicsAcrylics vary greatly over time in theirability to effectively transmit UV light.Acrylics sold by ETS have been life testedto ensure proper transmission throughouttheir useful life.

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:

Model 36: SPEED™ 175 Wolff® Model SPD75-T12 Bi-Pin

Model 36 3F: SPEED™ 175 Wolff® Model SPD75-T12 Bi-PinPhilips Model HPA 400/30s or CosmoTech Model 23045 or 20046 (facial unit)

23596-01A

22

Removing/Replacing Face TannerLamps on Face Tanner Models

After removing the canopy acrylic shield,replace the face tanner lamps as follows:

Step 1 Support the face tanner assemblywith your hand while unscrew-ing the two retaining screws. Theface tanner glass casing willswing downward.

Step 2 The lamp can now beexchanged. The lamp holdersare equipped with spring con-tacts which enable the lamp tobe removed easily. Remove theold lamp and discard. Install thenew lamp, using a clean clothor paper towel. Ensure that thelamp is firmly seated in thelamp holders.

Note! Never take hold of the lamp suchthat your fingers are in contact with thelamp glass. Finger oils will greatly reducethe lamp’s operational life.

Step 3 Gently close the face tannerglass casing and lock it closedwith the screws. Ensure that thescrews firmly secure the glasscasing.

RETAININGSCREWS

Never turn the equipment on while theface tanner is disassembled or when theglass filters have been removed. Thedirect light can cause severe injury to theeyes and other areas of the body.Immediately discontinue use of thisequipment if the face tanner glass is bro-ken or if any unfiltered light can be seenescaping the face tanner assembly.

WARNING!


2359

6-01

A 23

roubleshooting

Problem SolutionSunbed not tanning

Lamps fail to light and timer dis-play is blank

The last minute of tanning timedoes not count down from 59 sec-onds, but some time less than 59seconds

One or more lamps fail to light

The face tanners will not come on

The canopy will not stay up /The canopy will not stay down

My canopy opens and closes toofast (slamming, not enough resis-tance)

I forgot what address, or “id”, I setmy sunbed to

1. Clean sunbed, see Thorough Periodic Cleaning.2. Ensure supply voltage is between 208 and 230V AC.3. Replace lamps if lamp hours are greater than 800hrs.4. Replace acrylic.

1. Make sure the unit is connected to a power source.2. Check source of AC power. Reset circuit breaker or replace fuse.

If the timer button has been pressed to decrease tanning timeduring the session, the time expired in the current minute issubtracted from the last minute.

1. Check that lamp is installed correctly.2. Switch unlit lamp with a lamp that lights, if new lamp lights

and old lamp still does not, replace old lamp.

1. Face tanner operation is initially delayed by 5 seconds.2. Face tanners will not relight until cooled.3. Replace face tanner lamp, see Removing/Replacing Face

Tanner Lamps on Face Tanner Models.

Your sunbed uses a smooth gliding spring lift system to raisethe canopy. This lift system may need to be adjusted slightlyfrom time to time. See Final Adjustments for proper adjust-ment procedures. The canopy should raise easily as well asrest fully closed.

Your sunbed utilizes a damper which limits the canopy’smovement speed. This also serves as a safety device in case ofspring lift failure as the canopy will not crash down. Replacethe damper on back of unit.

By holding the body fan button for 3 seconds the timer displaywill briefly display three numbers; the installed timer softwareversion, a factory set timer code and then the sunbed’s “id”number.

23596-01A

24

Problem SolutionMy bed is connected to a T-Max®remote system but I am havingtrouble getting into “id” mode

When auto addressing the first beddoes not register an “id”

My bed won’t work with the T-Max® Manager remote system

Timer display changes to indicatea tanning time after the timer but-ton is pressed but lamps do notcome on

My bed is connected to the T-Max® Manager remote systemand when the delay time hasexpired the timer display startscounting down but the bed lightsdo not come on

My bed, connected to a T-Max®Manager, did not display “dL” butdoes indicate:

“0”

a tanning time and the lampshave come ona tanning time but the lampshave not come on

You have probably attempted to connect your sunbed to theremote system already. Disconnect the remote plug(s) from theports at the back of the sunbed, wait 90 seconds and try again.

When using the auto address feature of the T-Max® Manageryou must wait 10 seconds from the time you start the autoaddress function before addressing the first bed.

1. The sunbed must first be set to a unique address, see RemoteConnections.

2. The bypass or terminator plug may be installed in the series inan inappropriate location. Plug the bypass plug only into thebed at the end of the series.

1. Bypass plug is not installed, see Electrical Connections.2. A T-Max® terminator has been used. See ATTENTION in

Electrical Connections.3. If remote is being used, other than T-Max® Manager, the exter-

nal timer may not be activated.4. Remote wiring is incorrect, see the instructions provided with

the remote interface kit.

The auto start feature of the remote system is disabled, see theinstructions provided with your remote system.

1. Remote device has not been set.2. The sunbed has not been connected to the remote system, see

Remote Connections.1. Delay time of T-Max® Manager has not been set.2. Delay time has expired and session has begun.

Auto start function of T-Max® Manager has been turned off.Press the timer button to turn on lamps.

2359

6-01

A 25

Problem SolutionTimer display continues to show a0 after the timer button is pressed

Timer display is indicating Er 1












1. T-Max® Manager remote system has not yet been set. 2. Sunbed address is not set correctly, see Remote Connections.

Body lamps are on when they should be off, have servicetechnician check the contactor.

Body lamps are off when they should be on, have servicetechnician check contactor and its wiring from the main timerbox.

Bench lamps are on when they should be off, have servicetechnician check the contactor. (Units with separate benchcontactor only.)

Bench lamps are off when they should be on, have servicetechnician check the contactor and its wiring from the maintimer box. (Units with separate bench contactor only.)

Not currently used

Not currently used

Face Tanner contactor is closed when it should be open, haveservice technician check the contactor.

Face Tanner contactor is open when it should be closed, haveservice technician check the contactor and its wiring from themain timer box.

Ballast Drawer is open or drawer switch is broken.

Timer computer is in an illegal state, reset power to correct,replace main timer if error reoccurs.



23596-01A

Problem SolutionTimer display is indicating Er 13




The timer display is not responding;1. Check cable to display.2. Replace display assembly.3. Replace main timer box.


26

2359

6-01

A

23596-01A

J-36SOL

2359

6-01

A

J-36SOL3F

23596-01A

Ballast Tray

2359

6-01

A

Parts List(When calling for parts, first state your bed model

as J-36SOL or J-36SOL3F. Then refer to this listand illustrations for proper part identification.)

Access PanelAccess Panel Key*Acrylic, Bench* (with aluminum frame)Acrylic, Canopy* (with aluminum frame)Acrylic, Latch Retainer*Acrylic Latch Stud*Acrylic Protector Strip*Ballast, SPEED™ SystemBallast, 400W (face tanner lamps)Capacitor, 75uFContactor (Relay)Cover, Canopy FrontCover, Canopy RearDamper*Endcap, Bench Foot EndEndcap, Bench Head EndEndcap, Canopy Foot EndEndcap Canopy Head EndFan, BodyFan, CoolingFan RelayFilter*Handle Kit*Hardware Kit*Hinge Cover Panel*Hour CounterLamp Holder w/ Starter*Lamp Holder w/o StarterLamp Holder, Face Tanner*

CALL FOR SERVICE OR QUESTIONS: 1•800•449•3605ETS, Inc. 6270 Corporate Drive, Indianapolis, IN 46278-2900

Record this information for ease of service:

Date of purchase:

Bench serial number:

Canopy serial number:

Ballast tray ID number:

Lamps*Manual*Panel, Left Pedestal Front (all blue)Panel, Right Pedestal Front (blue/grey)Pillow*Profile, Bench Front (with warnings)Profile, Bench Rear*Profile, Canopy FrontProfile, Canopy Rear*Remote Connection PCB*Remote Control Bypass Plug*Schematic Packet*Shroud, Body Fan InsideShroud, Body Fan OutsideStarter, K-12* (main lamps)Starter, Face Tanner (ignitor)Support, Bench Acrylic* (“kickstand”)Thermostat* (for face tanner)TimerTimer Keypad Kit* (circuit board)Timer Keypad Pushbuttons*Wiring Harness, Keypad to Timer*Wiring Harness, Remote PCB to Timer*Wiring Harness, Resistor Code*

* Not shown

CALL FOR SERVICE ORQUESTIONS:

1•800•449•3605

6270 Corporate DriveIndianapolis, IN 46278-2900

This sunbed utilizes a proprietary system ofcomponents known as the Speed™ 175System. Only certified Speed™ Systemcomponents may be used as replacements,including lamps and ballasts.

36 / 36 3f user manual - tanning-bed-parts.comtanning-bed-parts.com/documents/ets tan...

Documents