3.4 orange handbook - lte project rtn hardware key issues & basic config....pdf
TRANSCRIPT
www.huawei.com
HUAWEI TECHNOLOGIES CO., LTD.
Security Level:
Orange LTE Microwave Project
RTN Hardware Key Issues & Basic
Configuration Guide
Huawei Jordan Office Network Product Line (Transport) 2015
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 2
Copyright © Huawei Technologies Co. Ltd. 2010. All rights reserved.
Reviewed Prepared by Complete Date Modify History Version SN
Yousef00701261 Ahmed
00724888
2-Apr-2015 Configuration &
Commissioning
V1.0 1
Yousef00701261 Chenxiang
00211421
3-Apr Hardware key issue V1.1 2
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 3
Instructions and Precautions for Handling Power Cable Terminals
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 4
Precautions for Handling the Toggle Lever Switch
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 5
Cable Connections
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 6
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 7
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 8
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 9
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 10
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 11
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 12
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 13
Checking the installation
Use OJO Project QC & PAT documents to complete the check
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 14
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 15
Login from
NMS port
NE Login
RTN980
1- Configure IP address: 129.9.0.222/16 on your laptop “default IP address for RTN is 129.9.X.Y/16” 2-Connect Ethernet Cable between RTN IDU NMS port & your laptop 3-Start WebLCT 4- Login to WebLCT by user: Admin (default password: Admin@123).
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 16
Login from
NMS port
Login from
NMS port
RTN950
NE Login
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 17
Creating an NE
①
②
③
④
Method 1:
Create an NE by
using the search
method.
Configuring the
RF link mode
Configuring the
IF/ODU Information
of a Radio Link
Configuring
an NE
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 18
Creating an NE
Method 2:
Create an NE by
using the
manual method.
① ②
③
④
⑤
Configuring the
RF link mode
Configuring the
IF/ODU Information
of a Radio Link
Configuring
an NE
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 19
Configuring the RF link mode
Configuring the IF/ODU Information of
a Radio Link
Configuring an NE
Modifying the NE ID/Name
①
②
③
④
⑤
⑥
⑦
Modify the NE ID.
The ID of an NE in
the network must
be unique.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 20
Add New Boards
Add new
ODU
Add new
ISV3
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 21
Creating a 1+1 Protection
Group
①
②
③
④
⑤
Configuring the RF link mode
Configuring the IF/ODU Information of
a Radio Link
Configuring an NE
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 22
Creating a 1+1
Protection Group Select the 1+1 SD/FD/HSB protection from
the Working Mode drop-down list.
Use the
default
value. Select a working IF board and a
protection IF board. In the case of 1+1
FD/SD protection group, the working
board and protection boards must be
configured in two paired slots.
Configuring the RF link mode
Configuring the IF/ODU Information of
a Radio Link
Configuring an NE
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 23
Configuring the RF radio link
Configuring the IF/ODU Information of
a Radio Link
Configuring an NE Configuring the
IF/ODU Information of a Radio Link
①
②
③
④
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 24
Configuring the
IF/ODU Information of a Radio Link
The AM function is disabled by default (keep disable).
These two parameters are available only when Enable AM is set to Enabled.
This parameter is available only when Enable AM is set to Disabled (Change based on LLD)
Set this parameter by strictly conforming to the design. The number of E1 services on both ends of a hop of a radio link hop. (Keep default)
Set the transmit frequency and the
transmit power. (follow MW LLD)
Used for recording performance events. The parameters are valid only when the ATPC function is enabled. Set the parameters according to the network planning documents.
If the OptiX RTN 900 is interconnected with the Packet radio equipment, this parameter is set to Enabled. Otherwise, this parameter is set to Disabled. (keep Disable)
Configuring the RF radio link
Configuring the IF/ODU Information of a Radio Link
Configuring an NE
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 25
Change RTN IP, Gateway, Subnet mask
Procedure
Select the NE from the Object Tree
in the NE Explorer. Choose
Communication > Communication
Parameters from the Function Tree.
Configure the communication
parameters of the NE.
Click Apply.
(Follow NE ID/IP sheet from Huawei)
By default NE IP follow NE ID & no
need to change it, just double
check.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 26
MW Link Configuration (Hop)
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 27
Creation ETH Service (E-Line)
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 28
Synchronizing NE Time
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 29
NE Performance Monitoring Time
Procedure In the NE Explorer, select the NE from the Object Tree, and then choose Performance > NE Performance Monitoring Time from the Function Tree. Configure the performance monitoring parameters of the NEs.
Select 15-Minute or 24-Hour. Select Enabled or Disabled in Set 15-Minute Monitoring or Set 24-Hour Monitoring. Set the start time and end time of the performance monitoring of NEs.