32wp95e

5/14/2018 32WP95E - slidepdf.com

http://slidepdf.com/reader/full/32wp95e 1/17

SERVICE MANUALDOCUMENTATION TECHNIQUETECHNISCHE DOKUMENTATIONDOCUMENTAZIONE TECNICADOCUMENTACION TECNICA

No copying, translati on, modifi cation on other use authorized. All rights reserved worldwide. • Tous droits de reproduction, de traductio n, d'adaptation et d'exécution réservés pour tous les pays. • Sämtliche Urheberrechte an diesen Texten und Zeichnungen stehen uns zu. Nachdrucke,Vervielfältigungen - auch auszugsweise - nur mit unserer vorherigen Zustimmung zulässig. Alle Rechte vorbehalten. • I diri tti di riproduzione, di traduzione, e esecuzione sono riservati per tutti i paesi. • Derechos de reproduccion, de traduccion, de adaptacion y de ejecucion reservados para todos los pai ses.

WARNING : Before servicing this chassis please read the safety recommendations.

ATTENTION : Avant toute intervention sur ce châssis, lire les recommandations de sécurité.

ACHTUNG : Vor jedem Eingriff auf diesem Chassis, die Sicherheitsvorschriften lesen.

ATTENZIONE : Prima di intervenire sullo chassis, leggere le norme di sicurezza.

IMPORTANTE :Antes de cualquier intervención, leer las recomendaciones de seguridad.

32WP95E - 0402

32WP95E

T V

Plasma



MAIN

FRANÇAIS ESPAÑOLDEUTSCHENGLISH ITALIANO

123456789

101112131415161718192021

NC

NC

21

17

19

15

13

20

18

16

14

1211

910

87

5

3

1

6

4

2

NC

AUDIO "R"

AUDIO "R"

AUDIO "L"

NOTE : ... etc. identifies each

pcb module.

AUDIO "D"

AUDIO "D"

AUDIO "G"

AUDIO

"BLEU"

AUDIO "G" MONO

"BLEU"

COMMUT. LENTE

"VERT"

"VERT"

"ROUGE"

COMMUT. RAPIDE

COMMUT. RAPIDE

VIDEO

VIDEO SYNCHRO

BLINDAGE PRISE

AUDIO "R"

AUDIO "R"

AUDIO "L"

AUDIO

"BLAU"

AUDIO "L" MONO

"BLAU"

AVUMSCHALTUNG

"GRÜN"

"GRÜN"

"ROT"

AUSTASTUNG

AUSTASTUNG

VIDEO

VIDEO ODERSYNCHRO

ABSCHIRMUNGDES STECKERS

AUDIO "D"

AUDIO "D"

AUDIO "I"

AUDIO

"AZUL"

AUDIO "I" MONO

AZUL

"CONMUTACIONLENTA"

"VERDE"

"VERDE"

"ROJA"

"CONMUTACIONRAPIDA"

"CONMUTACIONRAPIDA"

VIDEO

VIDEO O SINCRO

BLINDAJEDEL ENCHUFE

AUDIO "D"

AUDIO "D"

AUDIO "S"

AUDIO

"BLU"

AUDIO "S" MONO

BLU

"COMMUTAZIONELENTA"

"VERDE"

"VERDE"

"ROSSO"

"COMMUTAZIONERAPIDA"

"COMMUTAZIONERAPIDA"

VIDEO

VIDEO O SINCRO

INVOLUCRO METAL-LICO DELLA PRESA

AUDIO "L" MONO

"BLUE"

"GREEN"

"GREEN"

"RED"

"ROUGE" "ROT" "ROJA""ROSSO""RED"

SLOW SWITCH

FAST SWITCH

VIDEO

VIDEO VIDEO VIDEOVIDEOVIDEO

PLUG SCREENBOX

VIDEO OR "SYNC"

FAST SWITCH

AUDIO

"BLUE"

: OUTPUT - SORTIE - AUSGANG - USCITA - SALIDA • : EARTH - MASSE - MASSE - MASSA - MASA

MAINNOTE : ... etc. repères des

platines constituant l'appareil.

MAINNOTA : ... etc. marcas de las

placas que constituyen el aparato.

MAINNOTA : ... ecc. sigla delle

piastre dell' apparecchio.

MAINHINWEIS : ... usw. Kennzeichnung

der Platinen, aus denen das

Gerät zusammengesetzt ist.

: INPUT - ENTRÉE - EINGANG - ENTRATA - ENTRADA •

Indicates critical safety components, and identical components should be used for replacement. Only then can theoperational safety be garanteed.

Le remplacement des éléments de sécurité (repérés avec le symbole ) par des composants non homologués selon laNorme CEI 65 entraine la non-conformité de l'appareil. Dans ce cas, la responsabilité du fabricant n'est plus engagée.

Wenn Sicherheitsteile (mit dem Symbol gekennzeichnet) nicht durch Original - Ersatzteile ersetzt werden, erlischt dieHaftung des Herstellers.

La sostituzione dei componenti di sicurezza (evidenziati con il segno ) con componenti non omologati secondo lanorma CEI 65 comporta la non conformitá dell'apparecchio. In tal caso è "esclusa la responsabilità " del costruttore.

La sustitución de elementos de seguridad (marcados con el simbolo ) por componentes no homologados segun lanorma CEI 65, provoca la no conformidad del aparato. En ese caso, el fabricante cesa de ser responsable.

MEASUREMENT CONDITIONS - CONDITIONS DE MESURES - MESSBEDINGUNGENCONDIZIONI DI MISURA - CONDICIONES DE MEDIDAS

RICEVITORE :In UHF, livello d'entrata 1 mV, monoscopio barre :- PAL, norma G. bianco 100%.

Via SCART, livello d'entrata 1 Vpp, monoscopio barre :Colore, Contrasto, Luminositá media, Suono minimo.Programma selezionato PR 01.

Tensioni continue rilevate rispetto alla massa con un voltmetro digitale.

RECEIVER :On UHF,input level : 1 mV, bar test pattern :- PAL, I standard, 100% white.

Via the scart socket, input level : 1 Vpp, bar test pattern :

Colour, contrast and brightness at mid-position, sound at minimum.Programme selected : PR 01.

DC voltages measured between the point and earth using a digitalvoltmeter.

EMPFÄNGER :Bei UHF Eingangspegel 1 mV, Farbbalken :- PAL, Norm G, Weiss 100%.

Über die Scartbuchse : Eingangspegel 1 Vss, Farbbalken :

Farbe, Kontrast, Helligkeit in der Mitte des Bereichs, Ton auf Minimum.Zugeordnetes Programm PR 01.

Gleichspannungen mit einem digitalen Voltmeter zur Masse gemessen.

RECEPTEUR :En UHF, niveau d'entrée 1 mV mire de barres- SECAM, Norm L, Blanc 100%.

Par la prise Péritélévision, niveau d'entrée 1 Vcc, mire de barres .

Couleur, contraste, lumière à mi-course, son minimum.Programme affecté PR 01.

Tensions continues relevées par rapport à la masse avec unvoltmètre numérique.

RECEPTOR :En UHF, nivel de entrada 1 mV, mira de barras :- PAL, norma G, blanco 100%.

Por la toma Peritelevision, nivel de entrada 1 Vpp mira de barra.Color, Contraste, luz a mitad de carrera, Sonido minimo.Programa afectado PR 01.

Tensiones continuas marcadas en relacion a la masa con un voltimetro digital.

Do not disconnect modules when they are energized!Repairs on power supply section are to be carried out only with isolating transformer.

Ne pas retirer les modules lorsqu' ils sont sous tension. N'effectuer les travaux de maintenance sur la partie reliéeau secteur (Switch Mode) qu'au travers d'un transformateur d'isolement.

Module nicht bei eingeschaltetem Gerät entfernen!Servicearbeiten am Netzteil nur unter Verwendung eines Regeltrenntrafos durchführen.

Non scollegare le piastre quando sono alimentate!Per le riparazioni sulla sezione alimentatore, utilizzare un trasformatore isolatore.

No desconectar los módulos cuando están activados. Las reparaciones en la sección de alimentación de energíadeben ser ejecutadas solamente con un transformador de separación.



First issue 04 / 02 3

Page

DISASSEMBLING THE MODULES

Removing the optional speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Removing the back panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Removing the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Removing the fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Removing the chassis assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Removing the PDP module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Removing the optical Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Removing the power module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Removing the flat cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

BOARD LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DIAGNOSTIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

BLOCK DIAGRAMS

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ADJUSTMENTS

Mode service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fixed data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

White balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

PDP power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjustment table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

CONTENTS



DISASSEMBLING THE MODULES

4 First issue 04 /02

1. Removing the optional speaker

- Put the PDP Monitor Display with the screen face down on

the flat desk.

CAUTION : When placing the display with the face down,

lay the soft cloth under the screen to protect the screen

surface. And make sure there is nothing to damage the

screen surface like a screw or small part near by before

placing the display.

- Remove speaker lead wires (R & L).

- Remove 16 Screws and 4 plates . (Fig. 1)

2. Removing the back panel

- Remove the 14 screws (4X8), the 10 screws (5X8)and the 2 screws (3X8).

- Remove the back panel.

050403

0201

01

02

02

01

01

01

03 03 03 03

03

03

03

03030303

03

03

03 04 04

0404

0404

04

0404

04 05 05




3. Removing the front panel

- Remove the 16 screws (4X8),

- Remove the flat cable from button unit to audio unit.

- Lift the chassis assembly up from the front panel and place

it the face down to the desk on soft cloth.

ATTENTION:

This PDP monitor is used the different kind of screw. Using

correct screw is needed to avoid the damage.

ATTENTION:

As R/C Pre-amp is projected from surface of the panel, it is

necessary to place it out of desk as shown below.

07

06

06

06 06 06 06 06 06 06 06

06 06 06 06 06 06

07

06

R/C Pre-amp

Front panel

Desk



4. Removing the chassis assembly

- Remove the 2 screws (4X8 + 2 washers) and the 2

screws (3X6)

- Remove fans with holder plate.

- Remove the 14 screws (6X12) and the 4 screws (5X8),

- Remove the 2 hexagonal screws,- Slightly lift the chassis up,

- Disconnect the lead wire between main unit and panel

module from panel module side,

- Remove the fixing screw of the 2 yellow-green wires

(ground) from AC power connector and Panel Module,

- Remove the 4 screws (5X40)

- Remove the panel holders and the spacers located

between holder and module.

- Disconnect the lead wire between Audio Unit and panel

module from panel module side,

- Disconnect the 3 connectors (KPOW2, K6U and

KPOW3) from power unit,

- Disconnect the connector (KSENS1) of sensor unit,

- Lift the chassis assembly up from panel module.

20

19

18

12

11

17

16

15

1413

10

09

08

09

11

11

11

121211

08 10 10 08

1314 1419

1816

17

15

14 14 1313

15

20

13

13

13




5. Removing the PDP module

- Remove the 2 screws ( 3X8) and the 3 screws

- Remove the power unit and the sensor uni t with

holder plate from PDP module.

- Fix the 3 screws to PDP module after removing theabove mentioned units.

6. Removing the optical filter

The front cabinet includes optical filter to protect the panel

from damage, to improve picture quality, or prevent

exposure of interference.

- Remove the 4 screws ,

- Unscrew the 4 screws ,

- Remove the 6 screws ,

- Remove the 4 screws

- Remove 2 hexagonal screws to remove the PDP

module.

Note: cannot clean Panel surface or Optical Filter after

assembling Panel Module, if caught the dust to them.

25

29

28

27

26

22

2423

2221

2324

2222

21 21

22

2525


26 26 26 26

27 27 27 27

28

28

28

29

29

28

28

28

29

29



- Remove the 6 screws and pu ll the top bracket ,

- Remove the 4 screws and pull the r ight bracket,

- Remove the 6 screws and pull the bottom bracket,

- Remove the 4 screws and pu ll the le ft bracket,

7. Removing the power module

When replacing the PDP module, the power module must

be remove from the old PDP module and reassemble on the

new one. Proceed as follow:

- Remove the 7 screws (3x6),

Note:

The optical filter is easy to be damaged. Do not touch

directly by hand. If there is dust, remove it by watery

neutral detergent.

- Cut and remove the wire band ,

- Disconnect the wire from power module,

- Take out the power unit.

35

36

34

38

33

32

31

30


30

Gasket

32

3133

34

34 34

34

35

34

34 34

36

37

38




8. Removing the flat cables

This set use 3 kinds of connector for flat cable. To remove a

cable and not to damage it, proceed as below.

Type A:- Lift up the hook on both sides and pull the flat cable to

disconnect it.

Type B:

- Slide the hook on both sides and pull the flat cable to

disconnect it.

Type C:

- Pull the flat cable to disconnect it.

BOARD LOCATION

MAINAUDIO

PC TERMINALPOWER SWITCH RC RECEIVER

SENSOR POWER

Cable

Cable

Cable

Type A

Type B

Type C



WIRING DIAGRAM


M T G F A N

C O R E F E R R I T E


C O R E

F E R R I T E

C O R E

F E R R I T E


5 1

9 V

6 V

G N D

3 4 V

1 2 V

1 2 V

1 2 V

G N D

G N D

G N D

1

1 0

2

1

- 5 V

G N D

3

1

5 5

1 1

N E U T

L I V E 2

1

L I V E

N E U T

2

1

N E U T

L I V E

5 0

5 0

5 0

5 0

1

1

1

1

1 2

1 2

1 0

1 0

1 0

1 0

1

1

1

1

- 5 V G N D

G N D

6 V

9 V

G N D

G N D

G N D 1 2 V

1 2 V

1 2 V

1 0

2

1

1

3 4 V

G N D

3 . 3

V S T A N B Y

5 V

S T A N B Y

5 1

A C ( N E U T )

A C ( L I V E )

3 7 0 V

G N D

6 3

3

1

1

F G

3

3

1

1

F G

3 6

3 5

3 4

3 3

3 2

3 1

3 0

2 9

2 8

2 7

2 6

2 5

2 4

2 3

2 2

2 1

2 0

1 9

1 8

1 7

1 6

1 5

1 4

1 3

1 2

1 1

1 0 9 8 7 6 5 4 3 2 1

3 6

3 5

3 4

3 3

3 2

3 1

3 0

2 9

2 8

2 7

2 6

2 5

2 4

2 3

2 2

2 1

2 0

1 9

1 8

1 7

1 6

1 5

1 4

1 3

1 2

1 1

1 0

9 8 7 6 5 4 3 2 1

K R S P A

K 1 6 Y A

C N 1 B K

G N D 2

K G N D 1

K 3 U A

K P O W 3 A

K S P 9 0 1

A

K S P 9 0 2 A

L F 9 0 1 A

C N 1 A

C N 1 - K

7 S K

3 U - K

6 U

K P

O W E R 3

K 3 T - K

8 T

K P

O W 2

K 3 D - 8

D

K 1 0 A - 8

A

K 1 0 K - 8

K

K 1 0 C 1 9 C

K 1 3 N 1 9 N

EL901

EL902

F N 9 0 1

F N 9 0 2

K 8 W K 1 9 R C

K 8 P W

A C I N

L F 9 0 1

M 9 0 1

K P O

W 3

K P O W E R 3

K 6 C

K 8 W

K 3 S T

K 1 9 R C

K 8 P O 2

K P O W 2

K S E N S 1

K S E N 1

K F A N 2

K F A N 1

K 1 9 S W P

K 8 P W

K 8 T

K 6 U

K 3 U

K 3 T

K 1 9 C

K 8 K

K 8 D

K 3 D

K 1 0 C

K 1 9 N

K 1 3 N

K 1 0 K

C N 6 2

C N 6 1

C N 6 3 C N

1

K L S P

K R S P

K 1 6 Y

K 1 6 Z

K P O W E R 1

K 8 X

K 7 S

K 8 A

K 1 0 A

A C

c o r d

N o i s e

f i l t e r

1

1

+

-

+

-

2 0

1 9

1 8

1 7

1 6

1 5

1 4

1 3

1 2

1 1

1 0

9

2 0

1 9

1 8

1 7

1 6

1 5

1 4

1 3

1 2

1 1

1 0

9

2

1

4

3 5 7

6 8

2

1

4

3 5 7

6 8

A U D I O

M A I N

P C

R C

S W

POWERSW

SENSOR

L O G I C

B O A R D

A C

- D C

B O A R D

D C

- D C

F A N




DIAGNOSTIC

This set is equipped with a self-diagnostic function to detect power, audio amplifier, temperature and fan default. The trouble can beidentified either by a flashing of the tricolour led or by a message displayed on screen.

Start

Stop

The set switches in standby mode

Does the message "Warning! Internal fan is trouble, not working properly" appears on

screen for 10 seconds every 10 minutes?

Is the power LED flashing yellow

once?

Is the power LED flashing red twice?

Is the power LED flashing green twice?

Failure in fan'speripheral area

of the set

Check IC071 andits peripheralcomponents

on AUDIO PCB

Check Fan andSensor controlcircuit (IC1821)on AUDIO PCB

Check 9V, 12Vand 30V lineson AUDIO PCB

Check 9V, 12Vand 30V lineson AUDIO PCB

Is the power LED flashing green

three times?

No

No

Yes

Yes

No

Yes

No

Yes

Yes

Does the set switch off, after displaying the

message:"Warning! Internal

temperature is too high" for 10 seconds?

Temperature fail

No

Yes

Check 5V line on AUDIOPCB and 3.3V, 2.5V and

2.5VST lines on MAIN PCBIs the power LED flashing green once?

No

No

Yes

: Power Fail Line 3.

: Power Fail Line 1.(see next page)

Notes:In case of overlapped fails, flashing sequences are repeated in turn.If power fail is detected 3 times in 15 minutes, the monitor will stop operating.If the AC cord is unplugged, the information of fails will disappear.




POWER BLOCK DIAGRAM




PCR

G

B

MAIN

R

G

B

IC1124RGB SWITCH

IC207A/D CONVERTER

IC601RGB MATRIX

IC301MAIN SCALER

IC751LVDSINTERFACE

PDPPANELMODULE

RGB RGB

RGB

RGB

1(R)3(G)5(B)

7(R)15(G)22(B)

211915

RGB

PC

DVI

IC1301

RGB RGB

R/L

AUDIO

IC001AUDIO CONTROL(Fixed)

22(L),21(R)

16(L),15(R)

25(L),20(R)23(L),22(R)

IC071MAIN DIGITALAMP

+-

L

R

SPEAKER X2

10(L),13(R)

*

* Depending on DVI version, this audio line is bypassed to avoid the Audio Control IC.

GENERAL BLOCK DIAGRAM




It is necessary to enter the Service Mode in order to carry outalignment of the set. Most adjustments must be made withthe RCU.

The following operations must be done quickly:• Switch the monitor on,• Press and hold the MENUbutton on the monitor,

• Using the remote control, press the EXIT button andrelease it.

• Release the MENU button of the monitor.• Press the MUTE button.• The service mode menu appears on the screen.

Using the remote control:• Press the / buttons to select the adjustment.• Press the button to select the value of the adjustment.

• Press the / buttons to adjust the value.• Press the button to select the name of another adjustment.

NB : the value of the adjustment is memorized automaticallyinto a non volatile memory.

• To exit the service mode menu press the power ON/OFFbutton on the monitor.

ACCESSING SERVICE MODE

3 EXITING FROM SERVICE MODE

2 NAVIGATION INSIDE THE SERVICE MODE

MENUOK

I NP UT V OL UM E

MENU Button

Main

Sub

32035

019

PDP Time 001396

Feb-Dynamic

Cont0 63 (3F)

Main

Sub

32

035

019

PDP Time

001396

Feb-Dynamic

Cont0 63 (3F)

Main

Sub

32

035

019

PDP Time

001396

Feb-Dynamic

Cont0 63 (3F)

SERVICE MODE

1

ADJUSTMENTS

All circuits have been adjusted in factory to make the monitor operating basically. These adjustments are controlled by the CPU(IC801) and memorizzed into the memory (IC808). When the audio board or the memory is replaced, the fixed data must be set andthe white balance adjusted.

1. Setting the fixed data

- Make sure the received signal is good quality.

- Enter the service mode as above mentioned,- Check the fixed data are corresponding to the data table

on next pages and adjust if necessary,

- Exit the service mode.

2. Adjusting the white balance

- Input signal 1.0Vpp/75 Ω terminated,

- White pattern,

- Screen size : full,

- Picture image level : natural

- Enter the service mode,

- Select alternatively adjustment n°69 (Cont FEB - red),

n°70 (Cont FEB - green) and n°71 (Cont FEB - blue),

- Adjust alternatively to obtain a proper white balance,- After adjustment, confirm the white balance with a normal

picture.

3. PDP power supply

The PDP module stores voltage information and send it to

the power supply assembly to obtain the best voltage.

Therefore it is not necessary to adjust the PDP power

supply.




0 FEB-Dynamic Contrast 63 0 63 Picture Menu (Dynamic)1 Brightness 31 0 632 Color 45 0 633 Tint 0 -31 324 --------------- -- -- --5 FEB-Standard Contrast 50 0 63 Picture Menu (Natural)6 Brightness 31 0 637 Color 31 0 638 Tint 0 -31 329 --------------- -- -- --10 FEB-Cinema Contrast 31 0 63 Picture Menu (Cinema)11 Brightness 31 0 6312 Color 26 0 6313 Tint 0 -31 3214 --------------- -- -- --15 PC Graphic Contrast 63 0 63 Picture Menu (Graphic)

16 Brightness 31 0 6317 Color 45 0 6318 Tint 0 -31 3219 --------------- -- -- --20 PC Standard Contrast 40 0 63 Picture Menu (Standard)21 Brightness 31 0 6322 Color 31 0 6323 Tint 0 -31 3224 --------------- -- -- --25 PC-Text Contrast 31 0 63 Picture Menu (Text)26 Brightness 31 0 6327 Color 26 0 6328 Tint 0 -31 3229 --------------- -- -- --30 Sub Menu FEB Contrast 60h 00h FFh FEB Input31 Brightness 39h 00h FFh32 Color-S 78h 00h FFh S-Video33 --------------- -- -- --34 Tint 00h 80h 7Fh35 --------------- -- -- --36 Sub Menu PC Contrast 60h 00h FFh37 Brightness 39h 00h FFh38 Color-S 80h 00h FFh39 Tint 00h 80h 7Fh40 --------------- -- -- --51 Color Temp H-FEB Red DCh 00h FFh FEB Color Temperature (High)52 Green F0h 00h FFh

53 Blue FFh 00h FFh54 Color Temp M-FEB Red FFh 00h FFh FEB Color Temperature (STD)55 Green FFh 00h FFh56 Blue FFh 00h FFh57 Color Temp L-FEB Red FFh 00h FFh FEB Color Temperature (Low)58 Green EBh 00h FFh59 Blue CDh 00h FFh60 Color Temp H-PC Red DCh 00h FFh PC Color Temperature (High)61 Green F0h 00h FFh62 Blue FFh 00h FFh63 Color Temp M-PC Red FFh 00h FFh PC Color Temperature (STD)64 Green FFh 00h FFh65 Blue FFh 00h FFh

No. NoteAdjustment NameData Area

Adjustment ItemInitialData

Min Max

All data except in gray box area is fixed. Do not change for correct operating.Data in gray box area is initial. Can be set according to adjustment information.




66 Color Temp L-PC Red FFh 00h FFh PC Color Temperature (Low)67 Green EBh 00h FFh68 Blue CDh 00h FFh

69 Cont FEB Red FFh 00h FFh White Balance Adjustment70 Green F4h 00h FFh71 Blue D2h 00h FFh72 Bright FEB Red 80h 00h FFh Black Balance Adjustment73 Green 80h 00h FFh74 Blue 80h 00h FFh75 Cont PC Red 00h 00h FFh W/B (Differential Data to FEB)76 Green 00h 00h FFh77 Blue 00h 00h FFh78 Bright PC Red 00h 00h FFh B/B (Differential Data to FEB)79 Green 00h 00h FFh80 Blue 00h 00h FFh93 Sharpness-PC Sharpness 0 0 10 Filter

94 Sharpness-FEB1-50 Sharpness 10 0 10 Filter95 Sharpness-FEB1-60 Sharpness 6 0 10 Filter111 PDP COLOR8 PDP Internal Pattern Display ( Key)112 PDP WHITE PDP Internal Pattern Display ( Key)113 Side Bar 81 0 225 Brightness od Side Bar

No. NoteAdjustment NameData Area

Adjustment ItemInitialData

Min Max



The description and characteristics given here are of informative significance only, and non committal. To keep up the high quality of our products, we reserve the right tomake any changes or improvement without previous notice. • Les descriptions et caractéristiques figurant sur ce document sont données à titre d'information et nond'engagement. En effet, soucieux de la qualité de nos produits, nous nous réservons le droit d'effectuer, sans préavis, toute modification ou amélioration. • DieBeschreibungen und Daten in dieser Anleitung dienen nur zur Information und sind nicht bindend. Um die Qualität unserer Produkte ständig zu verbessern, behalten wir unsdas Recht auf Änderungen vor. • Le descrizioni e le caratteristiche date su questo documento sono fornite a semplice titolo informativo e senza impegno. Ci riserviamo ildiritto di eseguire, senza preavviso, qualsiasi modifica o miglioramento. • Las descripciones y características que figuran en este documento se dan a título de información yno de compromiso. En efecto, en bien de la calidad de nuestros productos, nos reservamos el derecho de efectuar, sin previo aviso, cualquier modificación o mejora. T

H O M S O N

m u l t i m e d i a S a l e s E u r o p e - S . A . a u c a p i t a l d e

3 0 0 0 0 0 0 0 - S i è g e : 4 6 , q u a i A l p h o n s e L e G a l l o 9 2 1 0 0 B o u l o g n e F r a n c e - R C S N a n t e r

r e B 3 2 2 0 1 9 4 6 4

THOMSON multimediaSales France46, quai Alphonse Le Gallo92648 Boulogne cedex

Tel. : 01 41 86 60 00Minitel : 3616 ou 3623 TCEDSInternet : http://www.thomson.fr

THOMSON multimedia

Sales UK Limited30 Tower ViewKings Hill, West MallingKent ME19 4NQ (England)Tel. : 44 (0) 173 252 0920

THOMSON multimediaSales Italy S.p.A.Via Leonardo da Vinci,4320090 Trezzano sul naviglio (Milano)Tel. : (02) 48 414 111

THOMSON multimediaScandinavia ABFlorettgatan 29 CS-25467 Helsingborg (Sweden)Tel. : 042 25 75 00

THOMSON multimediaSwitzerlandSeewenweg 5CH-4153 ReinachTel. : (61) 716 96 60

THOMSONConsumer Electronics Polandul.Gen.L. Okulickiego 7/905-500 Piaseczno (Varsovie)Tel. : (22) 757 10 80

THOMSON multimediaHungary KFTLajos u. 78. II.em.H-1036 BudapestTel. : 00 36 14 5334/80

THOMSON multimediaCzech s.r.o.ul. Dopravaku - dum Genius 1Dolni ChabryCZ - 18400 Prague 8Tel. : (2) 688 67 70

THOMSON multimediaSales Germany GmbH & Co oHGKarl-Wiechert-Allee 7430625 Hannover

THOMSON multimediaSales SpainAvenida Isla Graciosa, 1Edificio ÁncoraParque Empresarial La Marina28700 San Sebastián de los Reyes (Madrid)Tel. : (91) 384 14 19

THOMSON multimediaSales PortugalAvenida da Boavista, 35214106 PortoTel. : (2) 26 18 76 41

This technical documentation is for use by maintenance technicians onlyDocumentation technique exclusivement destinée aux professionnels de la maintenanceDiese Angaben und Hinweise sind ausschließlich für den Service des Fachhändlers bestimmtDocumentazione tecnica destinata esclusivamente ai tecnici dell'assistenzaDocumentación técnica destinada exclusivamente a los profesionales de mantenimiento

32wp95e

Documents