306-ok - kusam electrical manual.pdf · 2014. 8. 27. · 306 10a ma com vw discharge cap. before...
TRANSCRIPT
The Multimeter Structure (see figure 1)
1) LCD DISPLAY :A 3½ digit display (maximum reading 1999)indicates measured values, and features symbols indicating function, Low Battery, Continuity, Diode.
2) FUNCTION SELECTOR :To Select ACV, DCV, ACA, DCA, Resistance, Inductance, Capacitance, Frequency, Diode, Continuity & Transistor Test.
2
( Figure 1)
W
750V MAX1000V
200mA MAXFUSED
10A/60sec. MAXFUSED
CAT II 1000VCAT III 600V
306
10A mA COM VW
DISCHARGE CAP.BEFORE TESTING.
MAX /
OFF2m20m
200m
2
20
2000M
20M
2000K
200K20K 2K
200 2n20n
200n
2m200m
PNP
NPNhFE
20m10A
200m
A
200m
2
20200
1000750
Hz
DUTY%
H V
F
199.9 WKW
AC
MAX
%
hFE
hFEE B C E Cx Lx
1
3
Display Symbols (see figure 2)
( Figure 2)
199.9 WKW
AC
MAX
%
hFE
H
SymbolNo.
1
2
3
4
5
6
7
8
9
10
Meaning
Dangerous Voltages.
Indicator for AC voltage or current, The displayed value is the mean value.
Indicates negative reading.
Test of diode.
Data Hold is active.
The continuity buzzer is on.
A : Amperes (amps). The unit of current.
V : Volts. The unit of voltage.
Hz : The unit of frequency.
mV, V
Hz
- +
~
!
mA, A
The battery is low.
Warning : To avoid false readings, which could lead to possible electric shock or personal injury, replace thebattery as soon as the batteryindicator appears.
·)))
Caution :! If the value of voltage to be measured is unknown,
use the maximum measurement position (750) and reduce the range step by step until a satisfactory reading is obtained.
! The LCD displays “1” indicating the existing selected range is overloaded, it is required to select a higher range in order to obtain a correct reading.
! In each range, the Meter has an input impedance of approx. 10MW. This loading effect can cause measurement errors in high impedance circuits. Ifthe circuit impedance is less than or equal to 10kW , the error is negligible (0.1% or less).
! When AC voltage measurement has been completed, disconnect the connection between the testing leads and the circuit under test.
C. AC Current Measurement (see figure 5)
(Figure 5)
RedBlack
~
W
750V MAX1000V200mA MAX
FUSED10A/60sec. MAX
FUSED
CAT II 1000VCAT III 600V
306
10A mA COM VW
DISCHARGE CAP.BEFORE TESTING.
MAX /
OFF2m20m
200m
2
20
2000M
20M
2000K
200K20K 2K
200 2n20n
200n
2m200m
PNP
NPNhFE
20m10A
200m
A
200m
2
20200
1000750
Hz
DUTY%
H V
F
199.9 WKW
AC
MAX
%
hFE
hFEE B C E Cx Lx
(Figure 6)
RedBlack
~
W
750V MAX1000V
200mA MAXFUSED
10A/60sec. MAXFUSED
CAT II 1000VCAT III 600V
306
10A mA COM VW
DISCHARGE CAP.BEFORE TESTING.
MAX /
OFF2m20m
200m
2
20
2000M
20M
2000K
200K20K 2K
200 2n20n
200n
2m200m
PNP
NPNhFE
20m10A
200m
A
200m
2
20200
1000750
Hz
DUTY%
H V
F
199.9 WKW
AC
MAX
%
hFE
hFEE B C E Cx Lx
D. DC Current Measurement (see figure 6)
The DC current measurement has 3 measurement positions on the rotary switch : 20mA, 200mA, 10A.
To measure DC Current, connect the meter as follows :
1) Turn off power to the circuit. Discharge all High - Voltage capacitors.
2) Insert the red test lead into the mA or 10A terminal and the black test lead into the COM terminal
Never attempt an in - circuit current measurement where the open circuit voltage between terminals and ground is greater than 60V DC or 30V rms. If the fuse burns out during measurement, the Meter may be damaged or the operator himself may be hurt. Use proper terminals, function, and range for the measurement. When the testing leads are connected to the current terminals, do not parallel them across any circuit.
! Warning :
MUMBAI
TEST CERTIFICATE
DIGITAL MULTIMETER
This Test Certificate warrantees that
the product has been inspected and
tested in accordance with the published
specifications.
The instrument has been calibrated by
using equipment which has already
been calibrated to standards traceable
to national standards.
MODEL NO. ___________306
SERIAL NO. ___________
DATE: ___________
ISO 9001REGISTERED
QC
PASS
KUSAM-MECO
29 30
WARRANTY
Each “KUSAM-MECO” product is warranted to be
free from defects in material and workmanship
under normal use & service. The warranty period is
one year (12 months) and begins from the date of
despatch of goods. In case any defect occurs in
functioning of the instrument, under proper use,
within the warranty period, the same will be rectified
by us free of charges, provided the to and fro freight
charges are borne by you.
This warranty extends only to the original buyer or
end-user customer of a “KUSAM-MECO” authorized
dealer.
This warranty does not apply for damaged Ic’s,
fuses, burnt PCB's, disposable batteries, carrying
case, test leads, or to any product which in “KUSAM-
MECO’s” opinion, has been misused, altered,
neglected, contaminated or damaged by accident or
abnormal conditions of operation or handling.
“KUSAM-MECO” authorized dealer shall extend this
warranty on new and unused products to end-user
customers only but have no authority to extend a
greater or different warranty on behalf of “KUSAM-
MECO”.
“KUSAM-MECO’s” warranty obligation is limited, at
option, free of charge repair, or replacement of a
defective product which is returned to a “KUSAM-
MECO” authorized service center within the
warranty period.
31 32
THIS WARRANTY IS BUYER’S SOLE AND
EXCLUSIVE REMEDY AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
“KUSAM-MECO” SHALL NOT BE LIABLE FOR
ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES,
INCLUDING LOSS OF DATA, ARISING FROM
ANY CAUSE WHATSOEVER.
All transaction are subject to Mumbai Jurisdiction.
G 17,Bharat Industrial Estate, T. J. Road,
Sewree (W), Mumbai - 400 015. INDIA.
Sales Direct : (022) 24156638
Tel. : (022) 24124540, 24181649.
Fax : (022) 24149659
Email : [email protected]
Website : www.kusamelectrical.com
www.kusam-meco.co.in