1

EMULATOR IMMO

RENAULT without CAN

2

Jumper settings on board of Universal Car Emulator

Solder jumper J2, J3, J4 and J5 on the emulator

3

Syrius 32 without CAN

Syrius 34 1.4 1.6 2.0

EMS 3132

1.9 2.2 and 2.5 DCI without CAN

1.5 DCI without CAN

1.9 DTI 1 plug

1.9 DTI 2 plugs

1.9 Diesel DCU3

2.8 TD

3.0 gasoline 1 plug3.0 gasoline 1 plug

In selected models of ECU you can programmatically

disable immo without necessity to use the emulator.

Emulator immo to Renault cars

replaces damaged immobilizer or the car key.

It function after made changes in memory content of EngineControl Module ECU.

In case of losing the car keys or a car burglary, it enable to driveoff from the road to the car service.

.

Due to a low cost you can leave it in the car instead of buying anew immo or making car keys duplicate

Two LEDs indicating:

green - power

red - after adjusting it lights constantly and blinks each 2 seconds

5Syrius 32 without CAN

In ECU Syrius 32 is a flash 29F200 or 29F400.

In the addresses

from 4000 lo 7FFF find values 64 C7 and change these values

everywhere and two units before them into FF FF FF FF.

Do It in the whole map from 4000 to 7FFF!!!

7

I connecting emulator to ECU:

+12VACC-29pin

CODE - 58pin

GROUND- 3pin

cut off 58pin from plug !!!

8II connecting emulator to ECU:

Power for the emulator and ground take from the capacitor.

Code signal after desolder resistor 333

9

If transducer CAN A82C250 is on the plate in the computer,the ECU will not work with emulator !!

10

Syrius34 1.4 1.6 2.0

In ECU Syrius 34 is flash 29F200 or 29F400.

To match the emulator you need to replace all content into files

11

Power for the emulator take from the capacitor at the flash.

12

EMS 3132

In the EMS3132 drivers is flash 29F200 or 29F400.

13

In the addresses from 4000 to 7FFF find

values 64 C7 and change these values everywhere and two unitsbefore them Into FF FF FF FF.

Do It In the whole map from 4000 to 7FFF !!

14

Power for the emulator take from the capacitor at the flash.

Connect emulator as pictured by unsoldering the capacitor.

Connect to the point which goes to the processor.

15

1.9, 2.2 i 2.5 DCI without CAN

Renault Laguna 1.9 DCI 1999 year mechanical ignition switch.

16

In memory 5P08C3

in the addresses:

003E, 003F, 0040,0041

and

0044, 0045, 0046, 0047

type FF.

In ECU, immo line (code) of emulator solder to the point as pictured.

17

Power for the emulator take from the capacitor on the driver plate

Remove resistor 334.

Turn on the ignition for 30 seconds, turn it off for 30 seconds andrepeat it o few times.

181.5 DCI without CAN

Unlock version without odometer.Unlock version without odometer.

Replace content of 25080 and connect emulator, immo line is10 pin of processor, visible in the photo, which must be held up.

Then Adjust file

Power take from capacitor at the memory. Add injectors and settings byClip or Launch.

19

1.9 DTI 1 plug

20

Connecting emulator to ECU:

The immo line of emulator connect to the 59 pin of the driver.

GND and ACC connect to diode in the driver.

21

Bend 59 pin in plug ECU.

Renault Megane 1.9 DTI 2 plugs

22

174-177=FF and 1B7-1BA=FF

for coding or emulator

In memory 24C04 type 8C 00 73 FF from 174 lo 177 and 1B7 to 1BA.

Connecting emulator

in the ECU:

GND (brown) pin 4,5

ACC (black) pin 81

immo line (white) pin 15

Cut off pin 15 from wiring!!!

231.9 Diesel DCU3

Renault Kangoo 1.9 Diesel 2001

02-05 = 00 00 FF FF

82-85 = 00 00 FF FFFor coding

In memory 95080 change into 00 00 FF FF addresses from 00 to ODand 80 to 8D.

24Connecting emulator in the ECU:

bend - pin 20

Pin 20 must be bend in plug or cut off from the car wiring.

25

Connecting emulator to plug ECU:

power +12V ACC- 76 or 77pin

GND-78 or 79pin

CODE - 20pin (cut-off from plug ECU)

Mascott 2.8 TDMascott 2.8 TD

In memory 24C16 change from 040 to 1FF into FF.

26

Connecting emulator in the driver:

Cut off pin code of the driver from the wiring!!!

27

Laguna 3.0 gasoline 1 plug, memory 24C02

Cut off pin 50 of the

driver from the wiring!!!

Connecting the emulator

ACC- pin 3

ground - pin 24

immo - pin 50

Warning!Due to possible construction changes of the cars, before connecting

the device check signals by multimeter on the ECU plug.

In order to use emulator, inmemory 24C02 from 05A to

05F write values FF andfrom 0F2 to 0F7 write

values FF.