27 mm 144 mm - videxuk.com€¦ · 66251130-en - v1.3 - 15/06/16 1 6200 series art.fi6256 -...

66251130-EN - V1.3 - 15/06/161

6200 Series

Art. 6256 - Installation instructions

Art. 6256 3.5" colour videophone

27 mm 144 mm

182 mm

Fig. 1 +V - 1 2 V1 V2

24Va

c0V

ac

SW1

SW2

PT3 PT2

PT1

SW1

LB SB LD 2A 3A 4A 5A

Fig. 2

DESCRIPTIONSurface mount videophone incorporating a 3.5” Hi-Res full colour active matrix LCD monitor specific for “6 wire” videokit (VK4K, VRVK and VK8K range). It includes 4 buttons: “camera recall”, “open door” , “service” and “privacy”.2 LED’s* indicate the privacy activated and open door. Programmable privacy duration and number of rings. Intercommunicating call and door call. Adjustments: call tone volume switch (3 levels), picture hue, contrast and brightness.* The operation of some LED’s and the functions described may require additional cabling

PUSH BUTTONSService push button.Shorts the “SB” terminal to GROUND (open collector 24Vdc 100mA max) while the button remain pressed.

Camera recall button.Pick up the handset then press the button (Press once for door/gate 1, twice for 2 and so on up to a maximum of 4 entrances): the relevant LED switches ON and the monitor switches on showing the video from the door panel. The speech is also live and the door can be opened by pressing .Door-open / intercommunicating call button.With the handset lifted and speech lines open to the entrance panel, press this button to open the door. If the termi-nal “LD” is properly connected the relevant LED remains switched ON until the door is closed.Intercommunication only works when the system is in stand-by condition.Switch 4 of the SW1 dip-switch selects the type of intercommunication:OFF Intercommunication between two apartments - pick up the handset and press the key button to call the video-

phone(s) in the other apartment. A busy tone will signal that the other videophone is in conversation with the door station and so cannot be called.

ON Intercommunication between videophones in the same apartment- pick up the handset and press the key button one, two, three or four times to call videophone with extension ad-

dress 1, 2, 3 or 4 (Set on dip-switch 2&3 of SW1).Any intercommunicating conversation is always interrupted by an external call (i.e. External calls take priority).Privacy ON-OFF button.When the system is in stand-by, the pressing of this button activates (LED switched on) or disables (LED switched off) the “privacy” service. The service is automatically disabled when the programmed privacy time expires. When the service is enabled the videophone does not receive calls.

66251130-EN - V1.3 - 15/06/162

6200 Series


LEDS

Door open LED.Can be used to indicate the status of a door or gate. It requires a switched 12Vdc connection to terminal “LD”.

Privacy ON/OFF LED.When the videophone is in stand-by, this LED signals the privacy service status(ON = service enabled, OFF = service disabled).

CONTROLS

SW1 Call tone volume controll (3 levels).

PT1 Brightness control.

PT2 PT2 Hue control.PT3 PT3 Contrast control.

SETTINGS (DIP-SWITCH)The videophone setup is carried out by the 2 dip-switch banks.

Switches 1 Apartment AddressOFF 1ON 2Switches 2,3 Extension AddressOFF OFF 1ON OFF 2OFF ON 3ON ON 4Switch 4 IntercommunicationOFF Between videophones of the two apartmentON Between videophones in the same apartmentSwitches 5,6 Number of ringsOFF OFF 2ON OFF 4OFF ON 6ON ON 8Switches 7,8 Privacy duration timeOFF OFF 15 minutesON OFF 1 hoursOFF ON 4 hoursON ON 8 hours

2 WAY DIP-SWITCH (SW2)The two way dip-switch adjusts the impedance of the video signal. The default setting is “ON” for both switches (75 Ohm): when there are more videophones in parallel connection (without video distributor) both switches must be “ON” only on the last videophone (looking at the connection order) while for all other videophones both switches must be set to “OFF”.


66251130-EN - V1.3 - 15/06/163

6200 Series



SIGNALS ON CONNECTION BOARD+V 20Vdc Input/Output (As input 16÷20Vdc 0,5A – as output 20Vdc 0,5A max)– Ground reference for +V terminal.1 Speech line output from handset’s microphone and data signal (Approx. 12V in stand-by, 5V during a conversation)2 Speech line input toward the handset’s loudspeaker (Approx. 12V in stand- by, approx. 3V during a conversation)

V1 Balanced video signal 1 sync.-V2 Balanced video signal 2 sync.+

24Vac 1A max power input

LB Local call input (5V in standby, 0V to trigger)

SB Service button (open collector) active low output. The button goes active when the button is pressed (Open Collec-tor 24Vdc 100mA max)

LD 12Vdc input for door-open LED2A Speech line input toward the loudspeaker of the parallel telephone (Approx. 12V in stand-by, 3V during a conversation)3A Output switched ground for parallel telephone4A Output call tone for parallel telephone5A Input for door-open command from parallel telephone

TECHNICAL SPECIFICATIONPower Supply: Supplied by the BUS line, 20VdcPower consumption: Stand-by: 50mA Max Operating: 200mA MaxWorking Temperature: -10 +50 °C

66251130-EN - V1.3 - 15/06/164

6200 Series


Art. 6256 3.5" colour display videophone

Push toExit

Local Bell

DoorMonitor

NC

V2

BS

PTE

SLV1

2- 112V

out

+V C NO

4321

ON

1

Art.

4833

-1

Using Electric Lock 12Vdc 0.3A MaxCon serratura elettrica 12Vdc 0.3A Max

NC

V2

BS

PTE

SLV1

2- 112V

out

+V C NO

4321

ON

1

Art.

4833

-1

Affinche qualsiasi modifica alle impostazioni dei dip switch delvideocitofono o del posto esterno venga riconosciuta dal sistema,è necessario togliere l'alimentazione di rete all'impianto erestituirla.

In order to make the system recognize any modification of thevideophone's and outdoor station's dip-switch setting temporarilydisconnect the system from the mains and reconnect

Videx Electronics S.p.A.Via del Lavoro 1, 63020 Monte Giberto (AP)Phone: +39 0734 631669 - Fax +39 0734 631669www.videx.it - [email protected]

Autore:

Data modifica:

Data creazione:Title:

Notes:

Titolo:

Note: Cod.File:

Foglio

/ 11

Marco Rongoni

vk4k62h-002.dwg

23/10/2015

18/11/2015

12

34

56

78

12

ON

Address N.

ON

+V_ 1 2 V1

SB LD 2A 3A 4A

SW

2S

W1

LBV2 5A

1 Ext.1Art.6256

66251130-EN - V1.3 - 15/06/165

6200 Series




Autore:

Data modifica:


Notes:

Titolo:

Note: Cod.File:

Foglio

/ 11

Marco Rongoni

vk8k62h-002.dwg

17/11/2015

17/11/2015

Local Bell

Push toExit

Doo

rM

onito

r

Art.8833-1


Art.8833-1

In caso di modifica alle impostazioni dei dip switch delvideocitofono o del posto esterno, togliere temporaneamentel'alimentazione di rete.

In order to make the system recognize any modification of thevideophone's and outdoor station's dip-switch setting, temporarilydisconnect the system from the mains and reconnect

12

34

56

78

12

ON

Address N.

ON

+V_ 1 2 V1

SB LD 2A 3A 4A

SW

2S

W1

LBV2 5A

1 Ext. 1Art.6256

66251130-EN - V1.3 - 15/06/166

6200 Series




4321

ON

J1

VR4KAMK-1

Art.140

J2

Videx Electronics S.p.A.Via del Lavoro 1, 63846 Monte Giberto (FM)Phone: +39 0734 631669 - Fax +39 0734 631669www.videx.it - [email protected]

Autore:

Data modifica:


Notes:

Titolo:

Note: Cod.File:

Foglio

/ 11

Marco Rongoni

vrvk62h-001.dwg

22/10/2015

01/12/2015

Push toExit

Affinche qualsiasi modifica alle impostazioni dei dip switch delvideocitofono o del posto esterno venga riconosciuta dal sistema,è necessario togliere l'alimentazione di rete all'impianto erestituirla.

In order to make the system recognize any modification of thevideophone's and outdoor station's dip-switch setting temporarilydisconnect the system from the mains and reconnect

4321

ON

J1

VR4KAMK-1

Art.140

J2

Local Bell

Coax

NC

SL

ON

Art.

VR

4KC

M

12

34

56

78

12

ON

Address N.

ON

+V_ 1 2 V1

SB LD 2A 3A 4A

SW

2S

W1

LBV2 5A

1 Ext. 1Art.6256

1

66251130-EN - V1.3 - 15/06/167

6200 Series




Autore:

Data modifica:


Notes:

Titolo:

Note: Cod.File:

Foglio

/ 11

Marco Rongoni

vk4k62h-012.dwg

17/11/2015

18/11/2015

1

Art.4833-1

Using

Elec

tric Lo

ck 12

Vdc 0

.3A M

axCo

n ser

ratur

a elet

trica 1

2Vdc

0.3A

Max

1

Art.4833-1D

Pus

hto Exi

t

1

Affi

nche

qua

lsia

si m

odifi

ca a

lle im

post

azio

ni d

ei d

ip s

witc

h de

lvi

deoc

itofo

no o

del

pos

to e

ster

no v

enga

rico

nosc

iuta

dal

sis

tem

a,è

nece

ssar

io to

glie

re l'

alim

enta

zion

e di

rete

all'i

mpi

anto

ere

stitu

irla.

In o

rder

to m

ake

the

syst

em re

cogn

ize

any

mod

ifica

tion

of th

evi

deop

hone

's a

nd o

utdo

or s

tatio

n's

dip-

switc

h se

tting

tem

pora

rily

disc

onne

ct th

e sy

stem

from

the

mai

ns a

nd re

conn

ect

Loca

l Bel

l

Loca

l Bel

l

1 E

xt. 2

Art.

6256

1 E

xt. 1

Art.

6256

66251130-EN - V1.3 - 15/06/168

6200 Series



11

Marco Rongoni

vk8k62h-008.dwg

01/12/2015

01/12/2015

Using

Elec

tric Lo

ck 12

Vdc 0

.3A M

axCo

n ser

ratur

a elet

trica 1

2Vdc

0.3A

Max

Art.

8833

-1In

cas

o di

mod

ifica

alle

impo

staz

ioni

dei

dip

sw

itch

del

vide

ocito

fono

o d

el p

osto

est

erno

, tog

liere

tem

pora

neam

ente

l'alim

enta

zion

e di

rete

.

In o

rder

to m

ake

the

syst

em re

cogn

ize

any

mod

ifica

tion

of th

evi

deop

hone

's a

nd o

utdo

or s

tatio

n's

dip-

switc

h se

tting

, tem

pora

rily

disc

onne

ct th

e sy

stem

from

the

mai

ns a

nd re

conn

ect

Pus

h to

Exi

t

Art.

8833

-1

+

Art.

8800

1 2 3 4 5 6 7 8 1 2

ON

Add

ress

N.

ON

+V_

12

V1

SBLD2A3A4A SW2SW1

LB

V2

5A

1 E

xt. 1

Art.

6256

1 2 3 4 5 6 7 8 1 2

ON

Add

ress

N.

ON

+V_

12

V1

SBLD2A3A4A SW2SW1

LB

V2

5A

1 E

xt. 2

Art.

6256

1 2 3 4 5 6 7 8 1 2

ON

Add

ress

N.

ON

+V_

12

V1

SBLD2A3A4A SW2SW1

LB

V2

5A

1 E

xt. 3

Art.

6256

66251130-EN - V1.3 - 15/06/169

6200 Series


6200 Series Videophone wall mounting instructions

1. In order to install the videophone, it is necessary to remove the cover, which contains all the electronics, from the base: firstly disconnect the handset from the videophone (by removing its plug from the videophone), then press lightly the bottom part of the videophone and simultaneously pulling outwards the upper part as shown in Fig. 1.

2. Put the base of the unit on the wall at approx 135cm from the finished floor to mark the points for the fixing holes “A” (Fig. 2) remembering that the wires “D” (Fig. 3) must be fed through the hole “E” (Fig. 3). If you use the flush mounting box 503, embed it into the wall vertically at approx. 140cm from the finished floor and the base.

3. Following Fig. 3, make the holes “A”, insert the wall plugs “B” and fix the base with the screws “C” feeding the wires “D” into the hole “E”. If you have used the box 503, fix the base to the wall through the holes “F” using the screws “C”.

4. As shown in Fig. 4A, connect the wires to the removable terminals following the provided installation diagram. Connect the ter-minal blocks to the electronics contained in the cover as shown in Fig. 4B. Reinsert the handset and test system before closing. Note: Contrast and hue trimmers can be adjusted only if the videophone is open. Note while testing the system, it is advisable to hold the cover with your hand closing manually the hook switch of the handset (see Fig. 4B reference “G”).

5. Once testing is complete and all the necessary adjustments are made, disconnect the handset from the cover and close the unit as shown in Fig. 5: first hook it on the bottom then push in the top until you hear the clip.

6. Reconnect the handset and hang it as shown in Fig. 6.

1

2

Fig. 1

AB

G

Fig. 4

135c

m

Fig. 2

1

2

Fig. 5

A

B

A

B

D

F

E

F

C

C

Fig. 3

Fig. 6

66251130-EN - V1.3 - 15/06/1610

6200 Series


Notes

66251130-EN - V1.3 - 15/06/1611

6200 Series


Notes

MANUFACTURERVIDEX ELECTRONICS S.P.A.Via del Lavoro, 1 - 63846 Monte Giberto (FM) ItalyTel (+39) 0734 631669 - Fax (+39) 0734 632475www.videx.it - [email protected]

CUSTOMER SUPPORTAll Countries:VIDEX ELECTRONICS S.P.A.www.videx.it - [email protected]: +39 0734-631669 - Fax: +39 0734-632475

UK Customers:VIDEX SECURITY LTDwww.videx-security.comTech Line: 0191 224 3174 - Fax: 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU (LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.

Main UK office:VIDEX SECURITY LTD1 Osprey Trinity ParkTrinity WayLONDON E4 8TDPhone: (+44) 0870 300 1240Fax: (+44) 020 8523 [email protected]

Northern UK office:VIDEX SECURITY LTDUnit 4-7Chillingham Industrial EstateChapman StreetNEWCASTLE UPON TYNE - NE6 2XXTech Line: (+44) 0191 224 3174Phone: (+44) 0870 300 1240Fax: (+44) 0191 224 1559

Greece office:VIDEX HELLAS Electronics48 Filolaou Str.11633 ATHENSPhone: (+30) 210 7521028 (+30) 210 7521998 Fax: (+30) 210 [email protected]

Danish office:VIDEX DANMARKHammershusgade 15DK-2100 COPENHAGENPhone: (+45) 39 29 80 00Fax: (+45) 39 27 77 [email protected]

Benelux office:VIDEX BENELUXE3 Iaan, 93B-9800 DEINZEPhone: (+32) 9 380 40 20Fax: (+32) 9 380 40 [email protected]

27 mm 144 mm - videxuk.com€¦ · 66251130-en - v1.3 - 15/06/16 1 6200 series art.fi6256 -...

Documents