22806831 how to make transmission nodes visible on nms

8/10/2019 22806831 How to Make Transmission Nodes Visible on NMS

1/21

HOW TO MAKE PDH VISIBLE

ON NMS


2/21

If only one AMM (Access Module

Magazine) rack present on the site

(a) Jack in the SAU IP in the AMM rack at the First position

(b) Connect the Term Serve port of SAU IP with O&M port of anyMMU present in AMM with D - type connector

(c) Pin Configuration for D - type connector should be

2 cross with 2

3 cross with 3

5 straight with 5(d) Connect one end of the LAN cable at Ethernet port on SAU IP and

other with HUB provided the Modem should be present on thatsite


3/21

If two or more AMM (Access Module

Magazine ) rack present on the same site

Take one NCC (Node Communication Channel) cable Connect one end of the NCC cable with any of the MMU

present on AMM1

Connect the other end of NCC cable with any of the

MMU present on AMM - 2


4/21

Two Sites connected via BTSOL media

Connect RAC -1 (Remote Access Channel) port on SAUwith the modem present on site -1

Connect the RAC -2 port on SAU with the modem

present on site2

Then give the hope ID name on both the SAU accordingto their far ends (refer slide-12)


5/21

HOW TO MAKE SDH VISIBLE

ON NMS


6/21

AT RBSC LOCATION

(a) Give an IP to TRU with the process

Set UpDCNInterfaceEthernet (refer slide -13,14,15)

(b) Add the Static route via

Set UpDCNIP routingStaticAdd (refer slide 16,17)

Destination IP = 10.0.16.0 (constant)

Subnet mask = 255.255.255.0 (constant)Default Gateway = 10.20.95.1 (Variable)

(c) Check that area ID and it should be same for the whole ring

Set UpDCNIP routingOSPFAreas (refer slide 18)

(d) Give an IP Far End IP via

Set UpDCNInterfacesFar End (refer slide 19)

(e) Then connect one end of the LAN cable with the Ethernet port on TRU and other with theHUB along with the modem at that site


7/21

If two or more TRU present on Site

Log in 1st TRU whichis facing towards RBSC and putthe Far end radio IP as its default gateway

Log in 2nd TRU present on same site and give the 1st

TRU IP as its default gateway

Connect the both TRU with cross cable


8/21

HOW TO MAKE TRAFFIC NODE

VISIBLE ON NMS


9/21

AT RBSC LOCATION

Give an IP to TN via

ConfigurationBasic NE (refer slide-20)

Provide the default gateway as 10.20.95.1

Configuration

DCN

Static Routing (refer slide-21)Destination = 10.0.16.0

Subnet mask = 255.255.255.0

Default Gateway = 10.20.95.1

Make the area ID same as that of the ring

ConfigurationDCNOSPF Routing (refer slide-21)

Connect one end of LAN cable with TN and other with the HUB provided themodem present at that site


10/21

TN along w ith one TRU

Enable the DCN line in the TRU and mark it as a server

Set UpDCNInterfaceDCN lineRSOH bytes DCN line

Provide the same area ID in the DCN line, in the OSPFdynamic routing

Then log in the TN

Provide the TRU IP as its default gateway IP


11/21

TN along w ith two TRU

Execute the same settings as discuss earlier in any of

the one TRU


12/21


13/21


14/21


15/21


16/21


17/21


18/21


19/21


20/21


21/21

22806831 how to make transmission nodes visible on nms

Documents