2.1.1 glass panel...5/8/2018 glass panel and attachments → removal and installation → body...
TRANSCRIPT
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
2011 Eos
Report a problem with this article⇒ “2.1.1 Glass Panel”, page 124
⇒ “2.1.2 Glass Panel Cables”, page 131
⇒ “2.1.3 Sunroof Motor”, page 139
⇒ “2.1.4 Glass Panel Seal, from July 2007”, page 142
⇒ “2.1.5 Guide Rails”, page 143
2.1.1 Glass PanelRemoving
Note
♦ Sunshade already removed.♦ All screws are microencapsulated and must always be replaced.♦ Screw tightening torque: 3 Nm.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Loosen the end eyes -3 and 6- on tensioning bands-2 and 5- on the outside of the main hinge.
– Remove tensioned headliner without loosening additional ten‐sioning bands. Refer to⇒ “2.6.6 Tensioned Headliner, Removing”, page 248
– Remove tensioned headliner rail. Refer to⇒ “2.6.13 Tensioned Headliner Rail, Removing”, page 261 .
Note
♦ When the luggage compartment trim is installed, make sure the support is not positioned in the opening onthe longitudinal member.
♦ The bypass screw on the hydraulic pump must be opened after the repair position has been reached onvehicle from May 2007. This prevents damaging the hydraulic system.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Open roof with convertible top operating switch until it is justbefore the position shown.
– Place Hinge Supports -VAS 6365- in lowest position -2-.
– Place the hinge supports -VAS 6365- in the mounting hole inthe main hinge -1- and rotate the base -4- so that it is not posi‐tioned in the opening in the longitudinal.
– Switch the ignition off. The roof lowers in stages until the sup‐ports are resting on the longitudinal member.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Remove screws -3- and remove sunroof motor -2- from mount-4-.
Note
Remove glass panel only with help from another colleague.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– First mark position of sliding blocks -7-.
– Only loosen screws -6- on sliding block -7-, do not remove.
– Move the roof pillar toward the outside -arrow a- until the slider-3- in the slotted guide rail -4- can be guided over to front guiderails -2- without touching -arrow b-.
– Pull the glass panel out approximately 25 cm.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Loosen the cables -2- on the glass panel -1- from the left andright slotted guide rails -3-.
– Remove glass panel with slotted guide rail parallel out of rearguide rails -b arrows-. Raise front edge of glass panel slightly-arrow a-.
Installing
Note
♦ Make sure all components such the slider and bracket are installed.♦ The sliders -6- in the slotted guide rail -8- are coated in rubber up to the slider -11-.♦ The washer -9- must fit exactly into the openings. The glass panel will make noises if the guiding edge is
damaged.♦ The lower brace -12- faces downward, as illustrated.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Place the sliders -6 and 11- on the slotted rail -8-.
– Install the bracket and all the individual parts in this sequence:
♦ Screw -10- washer -9-, bracket -12-, washer -5-, glass panel-1-.
♦ Screw -10-, washer -9-, guide -8-, washer -5-, bracket -12-.
Note
Install glass panel only with help from another colleague.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Guide glass panel guide rails into rear guide rails.
Glass panel must be guided horizontally -a arrows- and parallelwhen doing this.
– Move roof pillar far enough toward outside -b arrows- so thatguide rail slider does not touch the front guide rails.
– Further installation is performed in the reverse order of re‐moval.
2.1.2 Glass Panel CablesRemoving
Note
♦ All screws are microencapsulated and must always be replaced.♦ Screw tightening torque: 3 Nm.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Loosen the end eyes -3 and 6- on tensioning bands-2 and 5- on the outside of the main hinge.
– Remove tensioned headliner without loosening additional ten‐sioning bands. Refer to⇒ “2.6.6 Tensioned Headliner, Removing”, page 248
– Remove tensioned headliner rail. Refer to⇒ “2.6.13 Tensioned Headliner Rail, Removing”, page 261 .
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Remove screws -3- and remove sunroof motor -2- from mount-4-.
Note
♦ When the luggage compartment trim is installed, make sure the support is not positioned in the opening onthe longitudinal member.
♦ To support roof, both sides of luggage compartment trim should be either removed or installed.♦ The bypass screw on the hydraulic pump must be opened after the repair position has been reached on
vehicle from May 2007. This prevents damaging the hydraulic system.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Open roof with convertible top operating switch until it is justbefore the position shown.
– Place Hinge Supports -VAS 6365- in lowest position -2-.
– Place the hinge supports -VAS 6365- in the mounting hole inthe main hinge -1- and rotate the base -4- so that it is not posi‐tioned in the opening in the longitudinal.
– Switch the ignition off. The roof lowers in stages until the sup‐ports are resting on the longitudinal member.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Remove the bolts -1-.
– Remove cover -2- from mount -4- and remove intermediateshaft -3-.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– First mark position of sliding blocks -7-.
– Only loosen screws -6- on sliding block -7-, do not remove.
– Move the roof pillar toward the outside -arrows a- until theslider in the slotted guide rail -4- can be guided over to frontguide rails -2- without touching.
– Pull the glass panel out approximately 25 cm.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Loosen the glass panel cables -2- from the slotted guide rails-3-.
– Remove cables from rear guide rails.
Installing
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Guide glass panel cables -2- into rear guide rails.
– Insert glass panel cables -2- in guide rail mount -3-.
Note
The -arrow- points to the direction of travel.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Place sunroof motor -2- in mount on guide tube -4-.
– Install 3 bolts 3-3-, tightening specification 4.5 Nm.
– Crank glass panel back as far as “stop” using emergency op‐eration.
– Position sliding blocks on applied markings and tightenscrews. Tightening specification: 9.5 Nm.
– Close the CSC roof and remove the hinge supports -VAS6365- .
– Install the intermediate shaft and the sunroof motor.
– Install the tensioned headliner and loosened tensioning cable.
– Adapt sunroof motor.
2.1.3 Sunroof MotorRemoving
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
The glass panel remains closed.
– Remove tensioned headliner without loosening tensioningbands. Refer to⇒ “2.6.6 Tensioned Headliner, Removing”, page 248 .
– Remove tensioned headliner rail. Refer to⇒ “2.6.13 Tensioned Headliner Rail, Removing”, page 261 .
– Remove screws -3- and remove sunroof motor -2- from mount-4-.
Installing
Note
♦ The sunroof motor is equipped with a closing force limit. If the roof runs into an obstacle during the closingprocedure, the motor stops and the glass panel moves in the opposite direction.
♦ If the glass panel is closed a second time with the switch, it runs with increased closing force. If the glasspanel still runs into an obstacle, it runs once again in the opposite direction.
♦ If the glass panel is closed a third time using the switch, it runs without a closing force limit.♦ All screws are microencapsulated and must always be replaced.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Place sunroof motor -2- on mount -4- and tighten screws -3-.Tightening specification: 4.5 Nm.
Both a re-installed sunroof motor and a new sunroof motor mustalways be adapted.
♦ Pull switch, glass panel -1- closes.
♦ Pull switch a second time, glass panel closes with increasedclosing force.
♦ Pull switch a third time, glass panel closes without closingforce limit.
In this way, the sunroof motor is adapted and learns the zero po‐sition.
– Install tensioned headliner rail. Refer to⇒ “2.6.14 Tensioned Headliner Rail, Installing”, page 262 .
– Install the tensioned headliner. Refer to⇒ “2.6.7 Tensioned Headliner, Installing”, page 251 .
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
2.1.4 Glass Panel Seal, from July 2007
Note
This seal is installed only on vehicle through July 2007.
Removing
– Open glass panel -1- completely.
– Remove seal -3- from mount in guide rails -2-.
Installing
– For easier installation, coat seal with soapy water.
– Carefully press seal -3- into guide rail mount -2-.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
2.1.5 Guide RailsRemoving
Note
After removing roof pillar trim, ensure trim is not damaged by the following roof movement.
– Loosen the end eyes -3 and 6- on tensioning bands-2 and 4- on the outside of the main hinge. Refer to⇒ “2.6.12 Routing Tensioning Bands 4 and 5”, page 260 . (asshown in illustration N61-10146)
– Remove roof pillar trim without loosening tensioning bands.Refer to ⇒ “2.6.15 Roof Pillar Trim”, page 263 .
– Remove screws -4- on eyes -3- and allow roof pillar trim -1- tohang down on tensioning bands -2-.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Open glass panel completely.
– Insert Guide Rail Assembly Gauge -VAS 6370- in upper guidein guide rail -4-, slit on knurled screw -3- must be horizontal.
– Obtain dimensions Guide Rail Assembly Gauge -VAS 6370-on front -a- and rear -b- of front guide rails and note thesedimensions.
– To measure, slide the gauge open as far as the front -arrow-and rear stops -arrow-.
– Remove the gauges again.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Place base -2- of Side Member Support -VAS 6367- on seatbelt guide rail -1- -arrow a-.
– Press the support together and allow the rectangular formationon the head -3- on the head to position itself on the guide rearguide rail -4- through the force of the spring-arrow b-.
– Tighten screws -5-.
– Measure the dimension between the head -3- and the screw-5- and note it down.
– Remove the support again.
Note
♦ When the luggage compartment trim is installed, make sure the support is not positioned in the opening onthe longitudinal member.
♦ To support roof, both sides of luggage compartment trim should be either removed or installed.♦ The bypass screw on the hydraulic pump must be opened after the repair position has been reached on
vehicle from May 07. This prevents damaging the hydraulic system.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Open roof with convertible top operating switch until it is justbefore the position shown.
– Place hinge supports -VAS 6365- in lowest position -2-.
– Place the hinge supports -VAS 6365- in the mounting hole inthe main hinge -1- and rotate the base -4- so that it is not posi‐tioned in the opening in the longitudinal.
– Switch ignition off, roof lowers in stages until supports -4- areresting on longitudinal member -5-.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Remove inner seal -2- in area of front guide rails.
– Remove water guide foil -1-.
– Press seal on again.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Mark the position of the screws -6-.
– Remove the screws -3, 4, 5 and 6-.
– Remove water drain from front guide rails. The water drainmay be bonded to the guide rail.
– Remove the guide rails -3- forward at an angle.
Installing
Note
All screws are microencapsulated and must always be replaced.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Install the guide rail -1- onto the guide -arrow a-.
– Turn the guide rail until the clip audibly latches into the roofpillar -arrow b-.
– Align the guide rail inside the roof pillar.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Install the screws -3, 4, 5 and 6-.
Note
Watch how the front and rear guide rails move when closing the convertible top.
– Close the roof as far as the windshield frame but do not lockit.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Place base -2- of Side Member Support -VAS 6367- on seatbelt guide rail -1- -arrow a-.
– Press the support together and allow the rectangular formationon the head -3- on the head to position itself on the guide rearguide rail -4- through the force of the spring-arrow b-.
– Adjust the noted dimension.
– Tighten screws -5-.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Check rear dimension -b- of guide rails -4- with Guide Rail As‐sembly Gauge -VAS 6370- .
– Adjust guide rails according to front dimension -a- that wasnoted using Guide Rail Assembly Gauge -VAS 6370- . Tightenthe screw -5-.
– Secure the gauge guide -1- in the guide rails -4-. Rotateknurled screw -3- so slit is vertical. Tighten knurled screw -2-.
Note
All screws are microencapsulated and must always be replaced.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Tighten the bolts -3, 4, 5 and 6-. Tightening specification: 9.5Nm.
Note
♦ When the luggage compartment trim is installed, make sure the support is not positioned in the opening onthe longitudinal member.
♦ To support roof, both sides of luggage compartment trim should be either removed or installed.♦ The bypass screw on the hydraulic pump must be opened after the repair position has been reached on
vehicle from May 2007. This prevents damaging the hydraulic system.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Open roof with convertible top operating switch until it is justbefore the position shown.
– Place hinge supports -VAS 6365- in lowest position -2-.
– Place the hinge supports -VAS 6365- in the mounting hole inthe main hinge -1- and rotate the base -4- so that it is not posi‐tioned in the opening in the longitudinal.
– Switch the ignition off. The roof lowers in stages until the sup‐ports are resting on the longitudinal member.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Remove the seal -2- in the glass panel area.
The guide rail must be free of dirt and grease.
– Install the water guide foil -1-.
The water guide foil must seal all around edges of front guide rail-arrows-.
5/8/2018 Glass Panel and Attachments → Removal and Installation → Body Exterior • 2011 Volkswagen Eos • MotoLogic
https://www.motologic.com/car/vw_2011_1f7_eos/article/d5a28f01ab0933e9f56844e14a6f62e8?returnPath=%2Fcar%2Fvw_2011_1f7_eos%2Fsearch%3Fkeywords%
– Press a Butyl Cord -D 450 273 A2- -3- formed into a ball onend of guide rail firmly onto water guide foil -1-.
– Press a second Butyl Cord -D 450 273 A2- formed into a ballfirmly onto water guide foil at a distance of 85 mm-dimension a- to first.
– Check for correct seating of both butyl cords on water guidefoil. No gap should be visible between both materials. Butylcord should not be formed to edge of guide rail.
– Secure seal -2- on roof pillar.
– Remove supports and close roof.
– Install roof pillar trim.