~~~~~~~~~~~~~~~~~~~~~~

EC- TYPE EXAMINATION CERTIFICATE1

2 Equipment or Protective System Intended for usein Potentially Explosive Atmospheres

Directive 94/9/EC

3 EC- Type Examination Certificate Number BASOIA TEX1427X

4

5

Equipment or Protective System: MODEL 2088/2090 SMART PRESSURE TRANSMITTERS

Manufacturer: ROSEMOUNT INC

6

7

Address: 12001 Technology Drive, Eden Prairie, Minnesota 55344-3695, USA

This equipment or protective system and any acceptable variation thereto is specified in the scheduleto this certificate and the documents therein referred to.

8 The Electrical Equipment Certification Service, notified body number 600 in accordance withArticle 9 of the Council Directive 94/9/EC of 23 March 1994, certifies that this equipment orprotective system has been found to comply with the Essential Health and Safety Requirementsrelating to the design and construction of equipment and protective systems intended for use inpotentially explosive atmospheres given in Annex II to the Directive.

The examination and test results are recorded in confidential Report N°

9

10

11

12

01(C)1131 dated 11 January 2002

Compliance with the Essential Health and Safety Requirements has been assured by compliance with:

EN 50281-1-1: 1998except in respect of those requirements listed at item 18 of the Schedule.

If the sign "X" is placed after the certificate number, it indicates that the equipment or protectivesystem is subject to special conditions for safe use specified in the schedule to this certificate.

This EC-TYPE EXAMINATION CERTIFICATE relates only to the design and construction of thespecified equipment or protective system. If applicable, further requirements of this Directive applyto the manufacture and supply of this equipment or protective system.

The marking of the equipment or protective system shall include the following:-

@ III D TI05°C T amb -20°C to +85°C

This certificate may only be reproduced in its entirety and without any change, schedule included.

File No: EECS 0914/03/006

~ ~

17

This certificate is wanted subject to the general conditions of the ElectricalEquipment Certification Service. It does not necessarily indicate that the apparatusmay be used in particular industries or circumstances.

~~ Electrical Equipment Certification Service~~ Health and Safety ExecutiveHSE Harpur Hill, Buxton, Derbyshire, SK17 9JN, United Kingdom DIRECTOR

Health & Safely Tel: +44(0)1298 28000 Fax: +44(0)1298 28244 16 January 2002ExecutIve internet: www.baseefa.com e-mail: baseefa.info.eecs@hsLgov.uk

'-*~~~~~~~~~~~~~~~~~=*~~~Re-issued 21 March 2002 to change special conditions for safe use

CERTlATEX\EQUlP\CATI-2\P, Issue 1, Dated September 1998Page 1/3

'-~~~~~~~~~~~~~~~~~~~~~~~

13 Schedule

14 EC-TYPE EXAMINAnON CERTIFICATE N° BASOIATEX1427X

15 Description of Equipment or Protective System

The Model 2088/2090 Smart Pressure Transmitter comprises of a 2088/2090 sensor module andan aluminium or stainless steel enclosure of approximately 75 mm diameter by up to 130 mm long.The enclosure is fitted with two removable screwed covers with nitrile or EPDM rubber '0' ringsproviding effective sealing equivalent to 1P66. One end cover can be replaced by an LCD meter unitwith a 9.53 mm thick glass window. The enclosure has previously been used on category IGDequipment covered by certificate BAS99ATEXI222.

The 2088/2090 sensor module screws into a threaded entry on the enclosure and maintains the IPrating of the enclosure by means of an '0' ring on the module. Electrical connection between themodule and the circuitry within the enclosure is achieved by flexible cable.

Electrical connection to the apparatus is by glanded cable entry which must maintain the IF ratingof the enclosure. The terminals are accessible by removing one of the end covers.

16 Report No.

01(C)l131

17 Special Conditions For Safe Use

1 The user must ensure that the maximum rated voltage and current (36 volts, 24 milliamps,d.c.) are not exceeded. All connections to other apparatus or associated apparatus shall havecontrol over this voltage and current equivalent to a category 'ib' circuit according toEN 50020.

2 Cable entries must be used which maintain the ingress protection of the enclosure to at least1P66.

3 Unused cable entries must be filled with suitable blanking plugs which maintain the ingressprotection of the enclosure to at least IP66.

4. Cable entries and blanking plugs must be suitable for the ambient range of the apparatus andcapable of withstanding a 7J impact test.

The 2088/2090 sensor module must be securely screwed in place to maintain the ingressprotection of the enclosure.

5.

18 Essential Health and Safety Requirements

None that are not covered by assessment against Harmonised Standard EN 50281-1-1: 1998.

,-*=*~~~~~$=*~~:%~~~~~~~~~~Page 2/3

'-'*'~~~~~~~~~~~~~:%~~~~~~~::::

13 Schedule

14 EC-TYPE EXAMINATION CERTIFICATE N° BASOIATEX1427X

19 DRAWINGS

Number

02088-1109

02088-1109

02088-1109

Issue

AC

AC

AC

Sheet

1

2

3

Date

II Dec 01

IIDecOl

II Dec 01

DescriptionEnclosure details

Enclosure details -LCD

Label

This certificate may only be reproduced in its entirety and without any change, schedule included.

'--*~~~~*~~~~~~~~~~~~~~~~~Page 3/3

BASEEFA List Keywords2TRANSMI