2015 product line - industrial controls · • improved control sequences, protections and other...
TRANSCRIPT
Table of content • VC2000 Controller
• Main features • Actuators, flow sensor • LED lights • Room sensors • Analog input (AI) • Addressing • Wiring • Comparison VC1000 -vs- VC2000
• M2000 Controller • Main features • Improved RTU sequence • M2000 MUA, sequence and operation • M2000 BLR, sequence and operation
• C1000 Controller • Main features • Various models
• T1100 stand alone thermostat • Main features
• Communicating Wall Sensors • Main features • Wiring
• NC2000 Network Controller • Main features
PL-VC2000
• Small footprint, installs everywhere • New integrated HALOMO® actuators • Two fully configurable outputs • Quick & easy installation and setup • Available with ``P.I.´´ flow sensor • Modbus or BACnet communication • 3x new wall sensors available • Fully compatible with existing Prolon gear
VC2000 VAV controller
New actuators / Air flow sensor
• The VC2000 uses brand new Belimo Halomo ® technology actuators • Standard torque (45 in-lbs) • High torque (90 in-lbs)
• Both models are also available as pressure independent with the optional air flow sensor
PL-VC2000 PL-VC2010-PI
VC2000 VAV controller
LED lights
The VC2000 uses bright, multicolored easy to read indication lights. Easy to see in a dark, crowded plenum! Each function has its unique LED No cover to open! Startup and troubleshooting procedures are facilitated
RS-485 NET Transm. (Red) RS-485 NET Rec. (Green)
RS-485 INT Transm. (Red) RS-485 INT Rec. (Green)
Processor / HBEAT. (Blue)
24Vac Supply (Blue)
Status (Yellow)
Analog Output (Orange)
Digital Output (Red)
VC2000 VAV controller
ProLon new wall sensors • The VC2000 is designed to operate with any
of the communicating wall sensors
• LVT #18/4 or CAT5e / RJ-45* cabling
• Full digital display PL-T1000 sensor with access to configuration parameters for service. Input for remote temp. sensor
• Digital PL-T500 sensor with setpoint / room temperature display
• Electronic PL-T200 sensor with set point adjuster only
*On sensor side only
PL-T1000
PL-T500
PL-T200
VC2000 VAV controller
VC2000
INT A
INT B
24 VAC
COM COM
24 VAC
INT B
INT A12
11
10
9
1
2
3
4
Analog Input (AI)
Multi purpose input allows many sequences:
• Supply air temp.* • Room temp (no local set point) • Discharge air temp. • Slab temp. (radiant heating) • Occupancy (contact input)
Input type is jumper configurable inside the controller, for other signal types(0-5Vdc, 4@20mA)
AICOM 13
14
Sonde de gaine (PL-CODS)
10 K type 3
JP40-5 volts4-20 mATHERMISTANCE
OU CONTACT SEC
JP4
(défaut)
Typical use as a supply air sensor for automatic changeover (when stand alone) *Default mode
VC2000 VAV controller
Virtual Addressing
Network addressing of the VC2000 is now done virtually, without switches. It can either be configured with the help of the Focus software or with any of the digital display wall sensors (T1000, T500)
Quick and easy addressing procedure using the Prolon Focus v.5.5.0 software
When ``Status’’ is on, no valid address is present in controller
VC2000 VAV controller
Wiring
End of line terminating resistor
Network comm. bus (toward unit controller) AI input Interface comm. bus + 24Vac supply for communicating wall sensor
Analog 0-10V output for heat / cool, etc. Digital output, dry contact -or- 24Vac for terminal heating, cooling, etc. 24Vac power supply
New removable and numbered terminal blocks
VC2000 VAV controller
PL-VC2000 PL-VC1000
• Unique platform incorporating 2x outputs (DO + AO) eq: VC1000LT+LMZS • New, more powerful HALOMO® actuators (45 & 90 -vs- 35 in-lbs) • Available with new, wide range pressure independent air flow sensor • Internal switches and jumpers eliminated (no cover to open!) • Easy diagnostic and troubleshooting with multicolor LED’s • New communicating wall sensor series (T1000, T500, T200) -vs- passive PL-RS • Very compact and easy to install (1/2 footprint of the VC1000) • Fully network compatible with other / existing VC1000 controllers • Focus software graphic interface is identical as VC1000
VC2000 -vs- VC1000
M2000 Unit Controller
New M2000 unit controller!
• New, larger universal platform • Multicolor LED’s for display • Comm. jumpers accessible from top • RS485 INT port is quadrupled! • Improved M2000 RTU roof-top model • 3x Brand new releases:
• M2000 MUA (Make-up Air) • M2000 BLR (Advanced Boiler) • M2000 HPS (Stand-Alone heat-pump)
Terminating and Bias resistors for the ``Interface´´ and ``Network´´ ports are now easily accessible from top of controller
The Interface comm. port has a dual RJ-45 socket connection but also two new screw type terminals to allow wiring with shielded, two wire pair cable as well as CAT5e
M2000 Unit Controller
(Advanced Roof Top) • New, and improved economizer
sequences
• Combined temperature and humidity
display
• New centralized dehumidification
sequence
• Improved control sequences, protections
and other tweaks!
M2000 RTU Roof-top Controller
M2000 RTU
Advanced economizer sequences • Actuator positioning based on cooling demand
(standard sequence)
• Actuator positioning based on outdoor temp reset
supply air set point.
• Controlled by either mixed or supply air sensor
location
M2000 RTU Roof-top Controller
Combined temperature and humidity display • As soon as a Prolon humidity controller is
networked with the M2000, both temperature and
humidity data are exchanged between them.
• The humidity controller adds return air
temperature info on its display along the return air
humidity reading. Likewise for the supply sensor.
• The M2000 unit controller does the same by
adding humidity reading to its’ corresponding
temperature sensors.
M2000 RTU Roof-top Controller
Centralized dehumidification sequence • Independent contact output from the Prolon humidity
controller (roof tops with built-in dehum. coil)
• Simultaneous cooling and re-heating from the RTU
controller .
• VAV zone terminal boxes automatically open to allow
most efficient ventilation.
M2000 RTU Roof-top Controller
(Make Up Air Unit) • Many seasonal control sequences
• Free + mechanical cooling sequences
possible
• Highly advanced limits and safeguards
• Alarm sequence with override
• Fixed or variable air flow (VFD)
• Building static pressure control
• Outdoor and ambiant temperature reset
strategies
M2000 MUA
M2000 MUA Make-up unit Controller
M2000 MUA (Make Up Air Unit) • Multiple seasonal control strategies / Free + mechanical cooling
• Exhaust fan / Manual Interlock strategy / Alarm with reset
• Fixed or variable air volume / Ambiant temperature supply set point reset
M2000 MUA Make-up unit Controller
Basic unit configuration • Fixed supply set point or zone temp
reset • Single air volume with fixed exhaust
rate • Dual air volume with two stage
exhaust strategy • Variable air volume for building
pressurization or indoor air quality control (Co2)
Winter control sequence • Outdoor temperature interlock
(heating) • Supply air set point reset by outdoor //
ambiant temperature • Fully integrated heating and cooling
demand reset band
Summer control sequence • Designed for mechanical cooling units
in mind • Outdoor temperature interlock
(cooling) • Cooling management by outdoor or
ambiant temperature conditions
M2000 MUA Make-up unit Controller
(Advanced Boiler) • New advanced boiler controller
• Controls up to 4x boilers
• Controls 2x pumps + modulating 3-way valve
• Lead-Lag & equal run time strategies on boilers
and pumps
• Dual reset control strategies
• Improved limits and safety interlocks
M2000 BLR Boiler Controller
M2000 BLR
Pump control • Runs single or two pumps • Outdoor temp and heating demand
interlock conditions • Lead-lag / backup pump sequence • Equal run time and pump exercise
sequences
Boiler control • 4x configurable DO’s:
Single 4x stage boiler Two dual stage boilers Four single stage boilers
• 1x Modulating 3-way valve • Outdoor temp and heating demand
interlock conditions • Lead-Lag / equal run time strategy
Temperature control • Fixed or outdoor temperature reset set
point • Additional reset by heating demand /
occupancy • Return temp limitation • Morning warmup start up sequence
M2000 BLR Boiler Controller
ProLon C1000
• C1000 VAV Zone controller (actuator-less) • C1000 HU Humidity controller • C1000 RTU Basic roof-top Master controller • C1000 HP Basic heat-pump Master controller • C1000 BLR Basic boiler controller • C1000 HPS Stand alone heat-pump controller • C1000 WLC Water loop controller • And more to come…!
C1000 Controllers
C1000 Controllers
C1000 VAV • Standard or pressure-independent operation • Controls remote floating or 0-10vdc mod. actuator • 5x fully configurable outputs (4xDO’s, 1x AO) • Great for other simple heat / cool applications • Uses analog PL-RS wall sensor + any
communicating sensors (T200, T500, T1000)
C1000 Controllers
C1000 HU • Humidification and dehumidification sequences • On-off and modulating humidification • Optional progressive supply high limit • Shares outdoor sensor / proof-of fan with Master • Outside air temperature set point reset • Stand alone or centralized dehumidification
C1000 Controllers
C1000 RTU • Master controller for VAV zones • Basic 2x heat/ 2x cool + fan sequence • Ideal for Constant Volume RTUs • Same performance & features as M2000 RTU
C1000 HP • Master controller for VAV zones • Basic 3x heat/ 2x cool + fan sequence • Ideal for Constant Volume RTUs • Same performance & features as M2000 HP
C1000 Controllers
C1000 BLR • Basic entry-level boiler controller • Single pump / 2x stage single boiler design • Can control modulating 3-way mix. Valve • Outdoor air reset strategy • Zone demand reset strategy • Can work stand alone or networked • Same performance as advanced M2000 BLR
C1000 Controllers
C1000 WLC • Closed water loop controller temperature controller • Controls a cooling tower + boiler together • Boiler acknowledgement contact • Cooling tower with or without a bypass valve • Controls tower spray pump, dampers and fan speed • Can work stand alone or networked • Ideal for multiple water sourced heat pump buildings
C1000 Controllers
C1000 HPS • Stand alone heat pump controller / single thermostat operation – no zones! • Air/air or Water/air condenser design • Ideally suited for large projects with multiple units and single water loop • Visualization is simplified by grouping multiple units on a single navigation page • Works with communicating wall sensors (T200, T500, T1000)
Stand alone, fully configurable heating / cooling thermostat
• Has two configurable outputs (1x AO + 1x DO)
• Multi-function AI sensor input: (Remote, Average, Slab temp.)
• Perfect for CV zones or terminal heating equipment
• Keypad access to all configuration parameters
• Can be networked for additional control strategies (occupancy scheduling, outdoor temp. lock out, etc.)
PL-T1100
T1100 Thermostat
NC2000 Network Controller
New NC2000 Network Controller! • Available now! • New universal platform (M2000) • Comm. jumpers available on top • RS485 input & output ports • More powerful processor, improved
communication performance • Interface comm. Port on both RJ-45 and
screw type terminals • More to come!
Prolon Focus App!
New Mobile Focus App!
• Available now! • Designed for Androïd v.4.0 tablets and
phones • Allows Wi-Fi, internet or hard wired
(USB) access to any Prolon system • Works on all screen sizes • User friendly navigation • Free to download!