2008-2017 mack truck peoplenet mobile gateway® standard ... · connect the pmg 2-pin male/female...
TRANSCRIPT
![Page 1: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/1.jpg)
2008-2017 Mack TruckPeopleNet Mobile Gateway® Standard Install
![Page 2: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/2.jpg)
Hardware Overview
Display
Display
Cable
Power
Assembly
2-Pin Main
Cable
AntennaPMG
Auxiliary
Cable
![Page 3: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/3.jpg)
Install Overview
Antenna
Display
Power and
Engine Data
PMG
![Page 4: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/4.jpg)
Display Mount
Mount the RAM mount base to
the top-right dash using bolts and
a backing-plate or large washers.
If the dash has an open space, drill a
1” hole to pass the cable into the
dash. If not, notch the dash edge
and pass the cable through the side.
If the dash has an open space, drill a 1”
hole to pass the cable into the dash. If not,
notch the dash edge and pass the cable
through the side.
![Page 5: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/5.jpg)
Engine DataLocate the J1939 backbone in the fuse
panel area. This is a black 2-pin with
yellow/green leads.
Connect the PMG 2-pin male/female to
the “Mack” pigtails, then connect those
pigtails to the J1939 creating a loop.
Model years 2008-2012 will also require the J1708
connection. Connect the black 2-pin pigtail to the
PMG cable. Cut off the opposite head and splice ¼”
ring terminals to the leads.
In the fuse panel area, connect the
yellow lead to the Serial A post and the
green lead to the Serial B post.
![Page 6: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/6.jpg)
Power ConnectionsSplice ¼” ring terminals to the leads on
the PMG Power Assembly then
connect them to the Power, Ignition,
and Ground as shown.
Ignition Sense
Constant Power
Ground
![Page 7: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/7.jpg)
Antenna
Clean the area to the right of the
fuse panel using alcohol and a
clean paper-towel. Slide the
antenna into the space and
secure it using the tape provided.
![Page 8: 2008-2017 Mack Truck PeopleNet Mobile Gateway® Standard ... · Connect the PMG 2-pin male/female to the “Mack” pigtails, then connect those pigtails to the J1939 creating a loop](https://reader030.vdocuments.mx/reader030/viewer/2022040611/5ed9dfb09a5976737b688396/html5/thumbnails/8.jpg)
PMG MountMount the PMG in the right-hand
space behind the gauge cluster
using 2 screws into the air-duct.