2000 series insect & security screen - … - supplementary.pdf2000 series insect & security...
TRANSCRIPT
SHEET REV DESCRIPTION SHEET REV DESCRIPTION SHEET REV DESCRIPTION
©
2000 SERIESINSECT & SECURITY SCREEN
-SUPPLEMENTARY SUITE2250 SERIES ROOF WINDOW DOUBLE GLAZED OPENING ROOF WINDOW CROSS SECTIONS RW 10 A
-SUPPLEMENTARY SUITE2250 SERIES ROOF WINDOW RECOMMENDED INSTALLATION - LONGRUN STEEL TYPE ROOF RW 12 A
-SUPPLEMENTARY SUITE2250 SERIES ROOF WINDOW RECOMMENDED FLASHING DETAILS - LONGRUN STEEL TYPE ROOF 22 63 A
-SUPPLEMENTARY SUITE2250 SERIES ROOF WINDOW INSTALLATION DETAILS POSTER RW 14 A
INSTALLATION OF THE 2250 SERIES ROOF WINDOW
This Roof Window unit has been quality checked in the factory and is in perfect working order.Incorrect packing and/or fixing will cause service problems after installation. Oversized packing willoften cause problems. The unit must fit into the trim easily with 5mm clearance at jambs, head and sill.
Check squareness of timber framed opening BEFORE attempting to install this roof window.
Install/seal all flashings as required for the particularsituation and roofing material. It is VERY importantthat the flashings are installed correctly otherwiseleaks will develop.
Pre-drill the roof window unit for nail fixings@600mm centres Ensure a minimum of 8 fixingsper roof window
Place a continuous bead of sealant around theunderside of the roof window frame to seal betweenthe window and the timber framing. Fit roof windowdown over the timber frame. Pack the head, sill andjambs as necessary so that the roof window unit isperfectly square. Use only flat, full width packersDO NOT USE WEDGES.
Fix the roof window unit in place and then sealaround the bottom of the outside leg of the frame toprevent water penetration between the frame andthe flashings.
Finish interior lining as per specifications
Sealant around outside of window frame
Bead of sealant under window frame
Roof window frame
Double nail fixings @450mm crs
Interior lining
Flashings under roofing
-SUPPLEMENTARY SUITESECONDARY DOUBLE GLAZING SECONDARY DOUBLE GLAZING - EXTRUSIONS & COMPONENTS SG 01 A
-SUPPLEMENTARY SUITEINTERIOR DOORS CONFIGURATIONS ID 001 -
Double SliderSingle Slider Double Slider Double Stacker
Supplementary: Interior Doors
General -• Multiple stacking is possible.• Additional variations of slider/stacker built into opening are available.• Combination front wall sliding and aluminium frame in opening i.e. Shopfront instead of timber lining can be suggested as well.• Beaded and boxed door panels are available as to the Pacific manufacturing packs.• All door panel manufacturing, refer to Pacific manufacturing pack (6600 Series Inside Slider/Stacker).• For specific design to suit on site, please contact the Technical Service team for assistance.
Opening inbuilt sliding
-SUPPLEMENTARY SUITEINTERIOR DOORS EXTRUSION DETAILS ID 002 -
70.530
35.5
23.5
12
33.5
28
12
26
18.2
32
10
70.5
10
38.5
18.2
321.
5
12
28
25
50
26
14.8
50
2678
50
48
9.5
36.8
Note:Please refer to the Pacific 6600Series for panel extrusions.
-SUPPLEMENTARY SUITEINTERIOR DOORS HARDWARE DETAILS ID 003 -
- 7mm High Woolpile 6.9mm foot
MC 363Track Fitting Bracket(Top Hung)
MC 362Flush Hinge(Bifold)
MC 361Bottom Guide(Top Hung)
MC 360Bottom Pivot Block(Bifold)
MC 368Wheel CarriageSS Wheel 50kg per wheel(Bottom Rolling)
MC 367Wheel Carriage Nylon Wheel25kg per wheel(Bottom Rolling)
MC 366Top Pivot Bracket (Bifold)Drill brass bush to accept 75003
MC 364Fixed Pivot Pin (bifold)Remove plastic sleeve & tapinto 102509 stile use 5/16" tap
MC 365Tandem Wheel(Bifold & Top Hung)use 5/16" tap
- Glazing Wedge Range
- 13mm High Woolpile
VINYLS AND SEALS
102504
102506
102509
102509
102510
-SUPPLEMENTARY SUITEINTERIOR DOORS PANEL ASSEMBLY ID 004 -
Bottom rolling doors a 5/16" hole for access to71050/71051 wheel adjustment screw is required
8g x 2" countersunkscrews step drilled
8g x 2" countersunkscrews step drilled
*3/8" to 3/16" step drilledrecess in bottom of tee slot
Note:Don't drill right through tee slot
*
12
-SUPPLEMENTARY SUITEINTERIOR DOORS BOTTOM ROLLING DOORS CROSS SECTIONAL DETAILS ID 006 -
102500
Glazing wedge
Glass infill
102510 Optional use ofwooden visionrail or 2510
Panel infill
102506
102501
102509
55016
Double Slider Single Slider
HORIZONTAL SECTIONS
VERTICAL SECTIONS
55004
-SUPPLEMENTARY SUITEINTERIOR DOORS TWO PANEL DOUBLE SLIDER CROSS SECTIONAL DETAILS ID 008 -
VERTICAL SECTION
HORIZONTAL SECTION
102502
102504
102506
102503
102509
102509
55004
223010 223010 leg notched
1370
8G
lass
4070
8
10
O/A
Fra
me
Pa
nel
336648
336663
78670
223011
50x50x3
10G Pan 19
55004
-SUPPLEMENTARY SUITEINTERIOR DOORS CROSS SECTIONS ID 009 -
223010
1370
8G
lass
4070
810
O/A
Fra
me
Pa
nel
223010
336648
336663
78670
223011
55004
10G PAN 9mm
-SUPPLEMENTARY SUITEINTERIOR DOORS CROSS SECTIONS ID 010 -
50
O/A Frame
O/A to Ctr Ctr to O/A
81130
336606336648
229000
223010
336618336605
64 8
12 Rail
Glass 8
12
Panel
17
Panel
10
50
229092
229092
223010
223010223010 leg notched
336648
336663
78670
223011
10G Pan 19
55004
-SUPPLEMENTARY SUITEINTERIOR DOORS CROSS SECTIONS ID 011 -
1370
8G
lass
4070
8
10
O/A
Fra
me
Pa
nel
Be
ad20
20
Frame
10648
Bead
Panel
1064 8 Glass
336606336648