2 piece abs shower drain installation instructions - bmi ... · installation instructions montreal...
TRANSCRIPT
INSTALLATION INSTRUCTIONS
Montreal ~ Vancouver ~ Toronto ~ Cincinnati
1-800-561-85791-800-361-1452
www.bmicanada.com
#08124 Two-piece ABS shower drain with stainless steel gridDesigned for installation with access underneath the floor a shower
+
+
Top partMale threaded
and grid
SHOWERFLOOR
SHOWERFLOOR
Rubber gasket
Paper gasket
Bottom partFemale threadedwith hex. base
1- Unscrew the two plastic parts (there is no need to remove the grid). 2- Place the top part in the floor opening of the shower with the grid facing up. 3- Place the rubber gasket around the male thread under the shower, facing the shower floor. 4- Place the paper gasket between the rubber gasket and the bottom part. 5- Screw the bottom part and make sure both gaskets are centered to the shower floor opening.6- Connect the 2" ABS pipe, as recomended by the pipe manufacturer.
Important notice: * This product has been design to be installed without the use of sealant. Therefore, you must not use silicone or plumber putty in the assembly.* Shower drains should be tightened with the appropriate tools using an adjustable wrench, a spud wrench or a strainer nut wrench. * To prevent any damage to the grid, the plastic film should be removed from the grid only after the installation is completed.
Note: You must have access underneath the shower floor for a proper installation of this type of shower drain.
Note II: Watertight installation of the drain is the installer’s responsability. Damages caused by drain leakage are excluded from the limited warranty of the product.
S I L I C O N E
INSTALLATION INSTRUCTIONS
Montreal ~ Vancouver ~ Toronto ~ Cincinnati
1-800-561-85791-800-361-1452
www.bmicanada.com
SHOWERFLOOR
SHOWERFLOOR
Top partMale threaded
and grid
Rubber gasket
Paper gasket
Bottom partFemale threadedwith hex. base
1- Unscrew the two plastic parts (there is no need to remove the grid). 2- Place the top part in the floor opening of the shower with the grid facing up. 3- Place the rubber gasket around the male thread under the shower, facing the shower floor. 4- Place the paper gasket between the rubber gasket and the bottom part. 5- Screw the bottom part and make sure both gaskets are centered to the shower floor opening.6- Connect the 2" ABS pipe, as recomended by the pipe manufacturer.
Important notice: * This product has been design to be installed without the use of sealant. Therefore, you must not use silicone or plumber putty in the assembly.* Shower drains should be tightened with the appropriate tools using an adjustable wrench, a spud wrench or a strainer nut wrench.
#08123 Two-piece ABS shower drain with white plastic gridDesigned for installation with access underneath the floor a shower
S I L I C O N E
Note : Pour ous devez avoir accès sous le plancher de la douche.
Note II : L’étanchéité de l’installation et du drain est la responsabilité de l’installateur. Les dommages causés par les fuites sont exclus de la garantie du produit.
compléter l’installation de ce type de drain de douche conformément aux exigences, v
INSTALLATION INSTRUCTIONS
Montreal ~ Vancouver ~ Toronto ~ Cincinnati
1-800-561-85791-800-361-1452
www.bmicanada.com
+
+
2
6
9
1- Stainless Steel Grid2- Male Threaded Top Part3- Shower Floor4- Rubber Gasket5- Paper Gasket6- Female Threaded Bottom Part9- ABS Pipe
5
4
1
3
AB
S 2
"
S I L I C O N E
INSTALLATION INSTRUCTIONS
Montreal ~ Vancouver ~ Toronto ~ Cincinnati
1-800-561-85791-800-361-1452
www.bmicanada.com
Sealing line limitWater flow
Properly installed
Improperly installed
Water flow
Silicone or Putty
Draining level
Draining level
Silicone or Putty
Water
Draining level
S I L I C O N E