16x24 garden shed plan · 2019-10-16 · 16x24 garden shed plan author: shedplans.org subject:...

16'x24' Garden Shed Plan

16'x24' Garden Shed Material List

Site Preparation

• Concrete• Bricks

Shed's Door

• Pressure-Treated Lumber• Wood siding boards• Plywood

Bottom Frame

• Pressure-Treated Lumber• Plywood

Side Walls Exterior Siding

• Pressure-Treated Lumber• Wood siding boards

Side Wall Frames

• Pressure-Treated Lumber

Top Frame


Shed’s Roof

• Pressure-Treated Lumber• Pressure-Treated Board• Plywood• Building paper• Asphalt shingles• Metal drip edge

Fasteners & Hardware

• Door hinges• Door pulls• Surface bolt• Window lock• Wood square louver gable vent• Galvanized nails• Wood screws

Shed's Window

• Pressure-Treated Lumber• Window beading• Glass

Drainage System

• Pressure-Treated Lumber• Half round gutter• End pieces with outlet• 45° elbow• Drainage pipe• Joint connector• End cap• Round hunger• Wall fastener

Shed's Window Shutter


Door Ramp

• Pressure-Treated Lumber• Plywood

Shed's Pergola


Walls Sheathing

• Plywood

8"4'-7 3/4"

8"4'-7 3/4"

8"4'-7 3/4"

8" 8"

23'-3 1/2"

8"

24'-7 1/2"

16'-7 1/2"

Foundation Preparation1.1 Clear the area where you want to build the shed and layout for the foundation. Use the below illustration as a guide.

1.2 For the foundation, dig the trenches at least 1 feet wide and 1 feet deep.

1.3 Fill the trenches to ground level with concrete and let cure, or harden. Since curing times vary between brands, read the packaging for recommended curing times.

1.4 Once the concrete has cured, use standard-sized bricks and lay them across the foundation. You will need roughly 350 bricks for this step.

STEP 1

1 1/2"

15'-9"

1 1/2"1 1/2"

1 1/2"

24'

Framing the Floor2.1 Assemble the frame using 1 1/2” x 7 1/4” pressure-treated lumber. You will need two

boards cut to 24’ that will be the rim joist and two boards cut to 15'-9” that will be the joist.

2.2 Secure the beams with 8x5" wood screws.

2.3 Using a speed square or carpenter's square, check the corners to make sure they are 90°.

STEP 2

11 1/2"

3 1/2"

1'-1 1/2"

1'-3 1/4"

1'-2 1/2" 1'-2 1/2"

1'-3 1/4"

1'-1 1/2"

5 x 1'-2 1/4

11 1/2"

3 1/2"

9'-4" 5'-4" 9'-4"

24'

1 1/2

"6'-

11"

1 1/2

"

11"

6'

5 x 1'-2 1/4

Assemble Front Wall Frame3.1 Using 1 1/2“ x 3 1/2“ and 3 1/2“ x 3 1/2“ pressure-treated lumber, construct front wall frame using the drawing below as a reference. You will need three boards cut to 11" that will be the cripple studs, one board cut to 5'-4" that will be the door header, eighteen boards cut to 6'-11" that will be the studs, two boards cut to 9'-4" that will be the bottom plates and one board cut to 24' that will be the top plate.

3.2 Connect the beams with 2x4" wood screws.


STEP 3

11 3/4" 11 3/4"16 x 1'-2 1/2"

1 1/2

"6'-

11"

1 1/2

"

24'

Assemble Back Wall Frame4.1 Using 1 1/2“ x 3 1/2“ and 3 1/2“ x 3 1/2“ pressure-treated lumber, construct back wall frame using the drawing below as a reference. You will need nineteen boards cut to 6'-11" that will be the studs and two boards cut to 24' that will be the top and bottom plates.



STEP 4

1'- 1/4" 1'-1" 1'-1" 1'-1" 1'- 1/4" 11" 11 3/4" 11" 1'- 1/4" 1'-1" 1'-1" 1'-1" 1'- 1/4"

1 1/2"

2'-10

1/2"

1 1/2"

3'-4"

1 1/2"

5 1/2"

1 1/2

"6'-

11"

1 1/2

"

15'-5"

3'-4"

Assemble Left and Right Wall Frames5.1 Using 1 1/2“ x 3 1/2“ pressure-treated lumber, construct side wall frames using the drawing below as a reference. You will need four boards cut to 5 1/2" that will be the cripple studs, four boards cut to 2'-10 1/2" that will be the studs, two boards cut to 3'-4" that will be the window header and rough sill, twelve boards cut to 6'-11" that will be the studs and two boards cut to 15'-5" that will be the top and bottom plates.



STEP 5

18 x 1'-2 1/2"

24'

Assemble the Roof Frame6.1 Using 1 1/2 “ x 5 1/2 “ pressure-treated lumber, cut thirty eight rafters 9'-5 1/2" long according to the dimensions.

6.2 Using 1 1/2 “ x 3 1/2 “ pressure-treated lumber, cut seventeen collar ties 7'-2 1/4" long according to the dimensions.

6.3 Using 3/4 “ x 7 1/4 “ pressure-treated board, cut the ridge board 24' long according the illustration below.


STEP 6

9'-5"

9'-5"

25'

Roof Sheathing Installation7.1 You will need 475 Sq Ft of asphalt shingle roofing.

7.2 Add the metal drip edge to the fascias.

7.3 Cover the plywood with building paper.

7.4 Install asphalt shingle roofing using an industrial stapler.

STEP 7

J ( 0,06 : 1 )

Window Installation for Left and Right WallsIt is necessary to prepare 2 windows.

8.1 Using 1 1/2 “ x 2 1/2 “ pressure-treated lumber, assemble the outer frame for the window as shown in the drawing below. You will need two boards cut to 3'-1" that will be the vertical girts and two boards cut to 3'-4" that will be the horizontal girts. Additionally, add vertical 2'-11 1/2" long and horizontal 3'-1" long supports using 3/4“ x 1“ lumber and cut the recesses for the window hinges.

8.2 Use 1 1/2 “ x 1 1/2 “ pressure-treated material to make the inner frame and secure with 3” wood screws. You will need two boards cut to 2'-9 3/4" that will be the vertical girts and two boards cut to 3'-3/4" that will be the horizontal girts. Mill a recess for the glass panes and for the hinges.

8.3 Use 1 1/4 “ x 1 1/2 “ pressure-treated material to make the inner frame supports and secure with 3” wood screws. You will need two boards cut to 2'-9 3/4" and mill a recess for interconnection.

8.4 Prepare and install glass into inner frame groove and fasten it by window beading from four sides. Use 1/2" galvanized nails.

8.5 Install two hinges (3") with 6x1" wood screws and assemble the window. Install a lock on the inner side of the window.

STEP 8

1'-7 3/4"

1'-7 3/4"3'-4"

3'-3

3/ 4

"

3'-3

3/4

"

Assemble and Install Window ShuttersIt is necessary to prepare 4 windows shutters.

9.1 Assemble frames using 3/4 “ x 1 1/2 “ pressure-treated lumber and secure with 3” wood screws. You will need one board cut to 1'-4 3/4" two boards cut to 3'-3/4" that will be the vertical girts and two boards cut to 1'-7 3/4" that will be the horizontal girts.

9.2 Mill a recess along the vertical girts for the jalousies.

9.3 Use 1/4 “ x 1 1/2 “ pressure-treated lumber for the jalousies. You will need twenty two boards cut to 1'-5 3/4".

9.4 Install two 3" door hinges using 6x1" wood screws.

STEP 9

6'-11 1/2" 1'-8 1/2" 6'-9 1/4" 1'-8 1/2" 6'-11 1/2"

6'-7"

Assemble and Install Decorative Door ShutterIt is necessary to prepare two decorative door shutter.

10.1 Assemble front frame using 1 1/2 “ x 1 1/2 “ pressure-treated lumber and secure with 3” wood screws. You will need two boards cut to 6'-7" that will be the vertical girts and two boards cut to 1'-5 1/2" that will be the horizontal girts.

10.2 Assemble back frame using 3/4“ x 2 1/2 “ pressure-treated lumber and secure with 5” wood screws. You will need two boards cut to 6'-7" that will be the vertical girts and two boards cut to 1'-3 1/2" that will be the horizontal girts.

10.3 Use 3/4 “ x 3/4 “ pressure-treated lumber for the lattice. You will need thirty six boards cut to 2'-3/4". Assemble according to the drawing.

STEP 10

Assemble and Install Roof Drainage System11.1 Assemble roof drainage system on the front fascia board. You will need 5" half round gutter 22' long, two end pieces with the outlet, six 45° elbows, two 3" pipes 6' long, two joint connectors and two end caps.

11.2 Fasten the round gutter to the fascia with the round hungers.

11.3 Fasten the vertical pipe section with the four wall fasteners.

22'

23'- 1/2"

5'

24'- 3/4"

STEP 11

Assemble and Install Door Ramp12.1 Assemble the five door ramp frames from pressure-treated lumber and secure with 3 and 5” wood screws. For each frame you will need one 1 1/2" x 1 1/2" board cut to 1'-8"; one 1 1/2" x 2 1/2" board cut to 3'-3/4" and one 1 1/2" x 3 1/2" board cut to 6 1/4".

12.2 Connect and secure all frames using one 1 1/2" x 2 1/2" board 5'-9" long and 3” wood screws.

12.3 Cut the 9/16" plywood sheet with dimensions 3'-3/4" x 5'-9" for the top plane and two sheets with dimensions 9 1/4" x 2'-9 1/2" for the sides.

12.4 Assemble siding shields with 2" galvanized nails.

5'-9"

3'- 3/4"

2'-9 1/2"

9 1/4"

STEP 12

Shed DecorationNow that your coop is all done, you are ready to decorate it any way you want using your favorite

paint, stain, or preservative.

STEP 13

CopyrightThe text and illustrations that appear here are the exclusive property of shedplans.org and are protected by federal copyright laws. The duplication, sale or distribution of any portion of these plans without prior written consent from the original designer will be subject to the appropriate penalties for copyright infringement. Sharing this plan on the web is only permited with an indicated original source: https://shedplans.org

For more great HOW-TO plans please visit: https://shedplans.org

16x24 garden shed plan · 2019-10-16 · 16x24 garden shed plan author: shedplans.org subject:...

Documents