1/5 hurricane mk.iid s.a. - eduard · hawker hurricane.....aero detail #12 hurricane in...
TRANSCRIPT
REFERENCES:Hawker Hurricane.........Aero Detail #12
Hurricane in action.........Sqaudron Signal #72
1/5
Hurricane Mk.IID S.A.
49 536
49 5361/48 scale detail set for kit • sada detailù pro model Hasegawa 1/48 Hasegawa
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM
20
J15
192 pcs.
67
53
J16
46
45
A4
A1
? OPEN CANOPY
J20
plastic2,0x2,0mm
5
29
30
322727
3
23
21
13
15
14
12
24
J2
K16
33 30
?
? 31
16
2/5 49 536
22
A1
18
6
22
8
K8
K15
28
J1K12
37
4
7 38
40
41
44
42
J8
11
A4
K12
37
17
J13
plastic0,4x5,0mm
58
10
10
43
K14
2
9
9
1
1
closed
open
plastic
insideF1
plastic
3/5 49 536
?
F1
180
90
59
64
180
9034
35
A1, A4
57
A1, A4
J20
57
69
J19
65
J18
5470
F1
F2
F3
3534
59 64
73
73
73
732 pcs.
62
61
63
60
4/5 49 536
F1
J3
B4
3636
C1
F1
J3
36
B4
36
71
L1
C2
56
C1
F1fill
wire
2pcsl-9,0mm
39
A1, A4
52 51
66
72
B4
J3
49
50
F1
47
48
F2
F3 55
Made in Czech RepublicEduard M.A. © 2010 www.eduard.com
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
PARTS WITH GLUE DÍLY OPATØENÉ LEPIDLEM
5/5 49 536
G2
K10
A1, A4
68
74
G1
26
25