140g-nti-e12, 140g-ntk-e12 lsig microprocessor...
TRANSCRIPT
OPTIONAL
140G-NS
140G-N
X2
OPTIONAL
X4
12
WARNING:
WARNUNG:
AVERTISSEMENT:
To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E).
Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E).
Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación Instalação - -
140G-N
140G-NS
LSIG
21
LSIG microprocessor-based electronic release for 140G-N, 140G-NSSganciatore elettronico a microprocessore LSIGElektronischer Mikroprozessor-Auslöser LSIGDéclencheur électronique à microprocesseur LSIGRelé electrónico con microprocesador LSIG
Bul. 140G
DIR 1000529R0502 (L6151)
140G-NTI-E12, 140G-NTK-E12
(2)
2
1
1
FOR 140G-NS ONLY
FOR ONLY140G-N
1 2
3 4
DIR 1000529R0502 (L6151)
5 6
7 8
2
2
1
1
1
2
(3)DIR 1000529R0502 (L6151)
11 140G-N
109
1
2
1
3
2
(4)DIR 1000529R0502 (L6151)
APPLY LABEL
12 140G-N
140G-NS
140G-NS
13
14 140G-NS
1
2
3
15
(5)
1.1 Nm
9.73 lb-in
DIR 1000529R0502 (L6151)
In Iu
1.1 Nm
9.73 lb-in
In Iu
2
1
2
1.5 Nm
13.27 lb-in
16 17
T5
T6
W4
W3
95S
98S
K1
K2
For3P+Nonly
T4
T3
T8
T7
T5
T6
W4
W3
95S
98S
W2
W1
K14
K15
K12
K13
K11
K10
K1
K2
T3
T2
T4
T1
98ST6
W3T5 95S
K2
K1
W4
(6)DIR 1000529R0502 (L6151)
TWISTED PAIR OFSHIELDED WIRES
ELECTRONICTRIP UNIT
LSIG
OUTPUT CONTACT
Uaux.24V
TU AL
48
>
ELECTRONIC TRIP UNIT
>>
>>
>>>
>>
LSlG
T6
T5
UI/N
NPE
TWISTED PAIR OFSHIELDED WIRES
19
18 140G-NS
In = 1600A
0.6 Nm
5.31 lb-in
if mountedse montatofalls montierts'il est montési está montado
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.
Copyright © 2013 Rockwell Automation, Inc. All Rights Reserved.
DIR 1000529R0502 (L6151)Publication 140G-IN046A-MU-P - April 2013
CONFIDENTIAL AND PROPRIETARY INFORMATION. THIS DOCUMENT CONTAINS CONFIDENTIAL AND PROPRIETARY INFORMATION OF
ROCKWELL AUTOMATION, INC. AND MAY NOT BE USED, COPIED OR DISCLOSED TO OTHERS, EXCEPT WITH THE AUTHORIZED WRITTEN
PERMISSION OF ROCKWELL AUTOMATION, INC.
Sheet
Size Ver
Of 11
A 0010000028320Dr. DateG. USHAKOW 02-12-10
MATERIALSIZE
FOLD
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
FLAT
SPECIFICATIONS FORINSTRUCTION SHEET CREATED BY STRATEGIC PARTNER
This Instruction Sheet is Being Printed by Strategic Partner
Note: After folding---Printed in (Country where printed)* and instruction sheet number in lower left corner should be visible.
* The printing vendor may change the instruction sheet files to show the correct country.