1348 1548 1948 pub 05-04 covers - earthmaster |...

© 2007 Alamo Group Inc.

PART'S MANUAL

M&W®

1020 South Sangamon Ave.Gibson City, Illinois 60936217-784-4261

DYNA-DRIVEGROUND-DRIVEN CULTIVATOR

Rev 02-07 DD 60 S/N 10095 -CURRENT Part No. 00771093P

An Operator's Manual was shipped with the equipment in theManual Canister. This Operator's Manual is an integral part ofthe safe operation of this machine and must be maintainedwith the unit at all times. READ, UNDERSTAND, and FOLLOWthe Safety and Operation Instructions contained in this manualbefore operating the equipment. If the Operator's Manual isnot with the equipment, contact your dealer or M&W(800-446-5158) to obtain a Free copy before operating theequipment.

TO THE OWNER/OPERATOR/DEALERAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator whorecognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement tobe used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Formin full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Cardand on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophicfailure with possible injury or death.

PARTSSECTION

Parts Section – 1

Parts Section – 2©2007 Alamo Group Inc.

PARTS ORDERING GUIDE

For maximum safety and to guarantee optimum product reliability, always usegenuine Alamo Group Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death. Directany questions regarding parts to:

The following instructions are offered to help eliminate needless delay and error in processingpurchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basicmachine featured in this manual. Part Numbers and Descriptions are given to help locate the partsand quantities required.

2. The Purchase Order must include the name and address of the person or organization orderingthe parts, who should be charged, and if possible, the serial number of the machine for which theparts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber, and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and aresubject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the proper PartNumber when ordering Replacement Safety Decals.

M&W1020 South Sangamon Ave.Gibson City, Illinois 60936217-784-4561

PART NAME INDEX

CRUMBLER 2000, 2600, 3000 Rev 04-04........................................................................................................................... 48CRUMBLER 2400, 3000, 3400 Rev 04-04........................................................................................................................... 50CRUMBLER 3000 Rev 04-04............................................................................................................................................... 46CRUMBLER 4000 - 5000 ......................................................................................................................................... 52, 54, 56CRUMBLER 6000 Rev 04-04......................................................................................................................................... 58, 60GREASE LINES AND SHIELDS - MODEL 6000................................................................................................................. 67LIGHT KIT - MODEL 4000, 5000 & 6000 ............................................................................................................................ 64MODEL 2000 MAINFRAME ................................................................................................................................................... 4MODEL 2400 MAINFRAME ................................................................................................................................................... 6MODEL 2600 MAINFRAME ................................................................................................................................................... 8MODEL 3000 MAINFRAME ........................................................................................................................................... 10, 12MODEL 3400 MAINFRAME ................................................................................................................................................. 14MODEL 4000 MAINFRAME ........................................................................................................................................... 16, 18MODEL 5000 MAINFRAME ........................................................................................................................................... 20, 22MODEL 6000 MAINFRAME Pub 08-06................................................................................................................................ 24REAR FLAP - MODEL 4000 & 5000.................................................................................................................................... 62REAR FLAP - MODEL 6000................................................................................................................................................. 63SIGNAL LAMPS - DUAL (AMBER) ...................................................................................................................................... 65SIGNAL LAMPS - DUAL (RED) ........................................................................................................................................... 66TRANSMISSION ASSEMBLY .............................................................................................................................................. 28TRANSMISSION ASSEMBLY Pub 08-06 ............................................................................................................................ 26TRIPLEX DRIVE TRANSMISSION ASSY 6000 S/N 10095 -Current Pub 08-06 ................................................................ 682000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07 ......................................................................... 342000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIESRev 02-07 .......................................................................... 322400, 3000, 3400 ROTOR SHAFT& BEARING ASSEMBLIES ........................................................................................... 363000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07 ............................................................................................. 304000 & 5000 ROTOR SHAFT & BEARING ASSEMBLIES ................................................................................................. 424000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 ............................................................................. 38, 406000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07................................................................................................ 44

Dyna Drive (Aug-06) -Current Rev 02-07

©2007 Alamo Group Inc. Parts Section – 3

MODEL 2000 MAINFRAME




ITEM PART NO. QTY. DESCRIPTION

1 852071 1 MAINFRAME 20002 552010 4 PIN3 852017 12 BRACKET - HINGE4 201143 24 COACH BOLT

00754583 24 FLAT WASHER00765676 24 SELF-LOCKING NUT

5 215046 4 HAIR COTTER PIN852054 1 GUARD - HINGED FLAP

6 06.012.03 2 LINK - FLAP ADJUSTMENT215046 4 PIN.HAIR

7 2196 2 CLIP552263 2 PIN, HITCH

16 3834200 1 SKID8277 4 PLOW BOLT00013901 4 NUT214124 4 WASHER

17 277476 1 FILLER CAP18 852006 1 CHAINCASE LH

00762395 9 BOLT00756026 7 BOLT9100206 9 SPRING WASHER00756164 7 LOCKING NUT

20 3830209 1 PLATE - DEPTH ADJUST LH3830208 1 PLATE - DEPTH ADJUST RH

21 214224 2 WASHER00762395 2 BOLT9100206 2 SPRING WASHER

22 3832030 2 PLATE - REFLECTOR MTG.








6 552039 2 LINK - FLAP ADJUSTMENT215046 4 PIN.HAIR

7 2196 2 CLIP552263 2 PIN, HITCH










2 552010 5 PIN3 852017 15 BRACKET - HINGE4 201143 30 COACH BOLT



6 06.012.03 2 LINK - FLAP ADJUSTMENT215046 4 PIN, HAIR

7 2196 2 CLIP552263 2 PIN, HITCH

12 852072 1 MAINFRAME 260016 3834200 1 SKID

8277 4 PLOW BOLT00013901 4 NUT214124 4 WASHER





22 3832030 2 PLATE - REFLECTOR MTG.









7 2196 2 CLIP3830219 2 PIN, HITCH (CAT II, CAT III)3834855 2 SPACER, HITCH3834854 2 SPACER, HITCH

9 2196 1 CLIP3830251 1 PIN, TOP LINK CAT II

10 2196 1 CLIP3830252 1 PIN, TOP LINK CAT III






22 3832030 2 PLATE - REFLECTOR MTG.23 2438621 1 SPADE - SMV24 00021400 2 BOLT25 32901C 2 LOCKNUT








6 552039 2 LINK - FLAP ADJUSTMENT215046 4 PIN, HAIR

7 2196 2 CLIP552263 2 PIN, HITCH

12 852072 1 MAINFRAME 300016 552007 1 SKID

8277 4 PLOW BOLT00013901 4 NUT214124 4 WASHER













7 2196 2 CLIP552257 2 PIN, HITCH (CAT II, CAT III)552258 2 SPACER

9 2196 1 CLIP3830251 1 PIN, TOP LINK PIN CAT II

10 2196 1 CLIP3830252 1 PIN, TOP LINK PIN CAT III














10 2196 1 CLIP3830270 1 TOP LINK PIN - CAT III

12 852087 1 MAINFRAME 400013 0838404 2 KLICK PIN

3830271 2 PIN, LOWER LINK - CAT III S/N 10725 AND AFTER3830210 2 PIN, HITCH - CAT III S/N 10700 - 107243834854 2 SPACER




19 852008 1 CHAINCASE RH00762395 9 BOLT00756026 7 BOLT9100206 9 SPRING WASHER00756164 7 LOCKING NUT

20 3830209 1 PLATE-DEPTH ADJUST LH3830208 1 PLATE-DEPTH ADJUST RH


23 2438621 1 SPADE, SMV24 00021400 2 BOLT25 32901C 2 LOCKNUT









9 2196 1 CLIP852032 1 PIN, HITCH

10 2196 1 CLIP852033 1 PIN, HITCH

12 852087 1 MAINFRAME 400013 2196 2 CLIP

552257 2 PIN, HITCH - CAT II, III552258 2 SPACER





20 852020 1 PLATE-DEPTH ADJUST LH852021 1 PLATE-DEPTH ADJUST RH








5 215046 4 HAIR COTTER PIN06.773.01 1 GUARD - HINGED FLAP


10 2196 1 CLIP3830270 1 TOP LINK PIN CAT III

12 3830205 1 MAINFRAME 500013 0838404 2 KLICK PIN

3830271 2 PIN, LOWER LINK CAT III S/N 10742 AND AFTER3830210 2 PIN, HITCH - CAT III S/N 10700 - 107413834854 2 SPACER







23 2438621 1 SPADE, SMV24 00021400 2 BOLT25 32901C 2 LOCKNUT







5 215046 4 HAIR COTTER PIN5A 852061 1 GUARD - HINGED FLAP LH5B 852060 1 GUARD - HINGED FLAP RH6 552039 2 LINK - FLAP ADJUSTMENT

215046 4 PIN, HAIR9 2196 1 CLIP

852032 1 PIN, HITCH10 2196 1 CLIP

852033 1 PIN, HITCH12 852070 1 MAINFRAME 500013 2196 2 CLIP

552257 2 PIN, HITCH - CAT II, III552258 2 SPACER

14 552293 1 SUPPORT, HINGE FLAP00751688 6 BOLT00754577 6 LOCKWASHER00755949 6 NUT









MODEL 6000 MAINFRAME Pub 08-06



MODEL 6000 MAINFRAME Pub 08-06


1 3830245 1 GUARD - RIGHT REAR HINGED FLAP2 3830254 1 GUARD - LEFT REAR HINGED FLAP3 852017 30 BRACKET - HINGE

201143 60 CARRIAGE BOLT00754583 60 FLATWASHER00765676 60 TOP LOCKNUT

4 552010 10 PIN5 3831045 4 BAR - LINK

215046 8 HAIRPIN COTTER6 3834200 2 SKID (7.00" WIDE)

3834201 2 SKID (8.34" WIDE)8277 8 PLOW BOLT00013901 8 NUT214124 8 WASHER

7 852006 1 CHAINCASE - LH (4.84" WIDE)3830291 1 CHAINCASE - LH (6.18" WIDE)

8 277476 2 FILLER CAP9 852008 1 CHAINCASE - RH (4.84" WIDE)

3830290 1 CHAINCASE - RH (6.18" WIDE)00762395 18 BOLT00756026 14 BOLT9100206 18 SPRING WASHER00756164 14 LOCKING NUT

10 3830271 2 PIN - LOWER HITCH (CAT III)11 3834854 2 SPACER12 00725708 2 PIN - SNAPPER13 3830270 1 PIN - UPPER LINK (CAT III)14 2196 1 PIN - CLIP15 3830247 1 MAINFRAME16 00021400 2 BOLT17 2438621 1 SPADE SMV18 32901C 2 LOCKNUT



TRANSMISSION ASSEMBLY Pub 08-06



TRANSMISSION ASSEMBLY Pub 08-06

ITEM PART NO. 2000 26000 3000 QTY 4000 5000 6000 QTY DESCRIPTION

1 552004 1 2 CHAIN - ROLLER2 241705 1 2 SPROCKET3 552214 1 2 WASHER

00756373 1 2 BOLT701615C 1 2 SPRING WASHER

4 04.278.02 1 2 SPROCKET5 552215 1 2 WASHER


11 08.816.01 1 1 TENSIONER BRACKET - LH08.816.02 - 1 TENSIONER BRACKET - RH

14 852007 1 2 ROD-SPRING GUIDE212419 2 4 LOCKING NUT

15 552008 1 2 SPECIAL NUT16 214226 1 2 FLAT WASHER17 225092 1 2 SPRING - COMP18 852081 1 2 BRACKET - TENSIONER19 552279 2 4 PLATE - NYLON GUIDE

00765676 2 4 SELF-LOCKING NUT00766178 2 4 BOLT

22 214226 1 2 FLAT WASHER23 0401225 1 2 CIRCLIP24 552009 1 2 PIN25 214224 1 2 WASHER

9313056 1 2 BOLT9100206 1 2 SPRING WASHER



TRANSMISSION ASSEMBLY



TRANSMISSION ASSEMBLY

ITEM PART NO. 2400 3000 3400 QTY 4000 5000 QTY DESCRIPTION

1 552004 1 2 CHAIN - ROLLER2 241705 1 2 SPROCKET3 552214 1 2 WASHER


4 241706 1 2 SPROCKET5 552215 1 2 WASHER


6 852079 1 1 BRACKET, CHAIN STOP LH852080 - 1 BRACKET, CHAIN STOP RH

7 552116 1 2 PIN IDLER9313056 1 2 BOLT9100206 1 2 SPRING WASHER

8 241707 1 2 SPROCKET9 552021 1 2 SPACER, BEARING10 221036 2 4 COLLAR, SPACER11 852031 1 2 BRACKET, CUSHION ARM12 243685 2 4 BEARING13 552213 1 2 WASHER14 852007 1 2 ROD-SPRING GUIDE

212419 2 4 LOCKING NUT15 552008 1 2 SPECIAL NUT16 214226 1 2 FLAT WASHER17 225092 1 2 SPRING - COMP18 852081 1 2 BRACKET - TENSIONER19 552279 2 4 PLATE - NYLON GUIDE

00765676 2 4 SELF-LOCKING NUT00766178 2 4 BOLT

22 214226 1 2 FLAT WASHER23 0401225 1 2 CIRCLIP24 552009 1 2 PIN25 214224 1 2 WASHER

9313056 1 2 BOLT9100206 1 2 SPRING WASHER

26 852014 1 2 BRACKET SPRING MOUNT LH00762401 2 4 BOLT00756164 2 4 LOCKING NUT

27 852015 1 2 BRACKET SPRING MOUNT RH00762401 2 4 BOLT00756164 2 4 LOCKING NUT

28 552020 1 2 PLATE SPRING MTG.00756026 4 8 BOLT00756164 4 8 LOCKING NUT

29 277474 1 2 RUBBER BUFFER00756164 1 2 LOCKING NUT



3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07



3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07


1 552015 1 SPACER2 852038 1 ROTOR SHAFT - FRONT3 06.949.01 92 TINE - CLOCKWISE TWIST

9100206 92 SPRING WASHER202851 92 BOLT00756105 92 LOCKING NUT

4 06.949.02 92 TINE - COUNTERCLOCKWISE TWIST9100206 92 SPRING WASHER202851 92 BOLT00756105 92 LOCKING NUT

5 06.950.01 64 PLATE - TINE SPACER9100206 64 SPRING WASHER202851 64 BOLT00756105 64 LOCKING NUT

6 852039 1 ROTOR SHAFT - REAR7 552117 1 COLLAR20 221035 2 COLLAR22 223051 2 SEAL23 222156 4 SNAP RING24 852049 2 HOUSING - BEARING

00766457 2 GREASE FITTING (METRIC)00003500 2 GREASE FITTING (NPT)

25 243687 2 BEARING26 3830213 1 PLATE STRUT

00756373 4 BOLT9143007 8 LOCKING NUT00765901 3 BOLT

28 243683 2 BEARING ASSEMBLY- FLANGED02957275 8 BOLT9143007 8 LOCKING NUT

29 852022 2 DUST COVER30 3836800 2 SEAL10 41895.01 15 TINE - CLEARING LH - LONG


11 41895.02 15 TINE - CLEARING RH - LONG9100206 15 SPRING WASHER202851 15 BOLT00756105 15 LOCKING NUT



2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIESRev 02-07



2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIESRev 02-07

ITEM PART NO. 2000 QTY 2600 QTY 3000 QTY DESCRIPTION

1 552015 1 1 1 SPACER2 852051 1 - - ROTOR SHAFT - FRONT (2000 UNIT)

852050 - 1 - ROTOR SHAFT - FRONT (2600 UNIT)852038 - - 1 ROTOR SHAFT - FRONT (3000 UNIT)

3 06.949.01 62 80 92 TINE - CLOCKWISE TWIST9100206 62 80 92 SPRING WASHER202851 62 80 92 BOLT00756105 62 80 92 LOCKING NUT

4 06.949.02 62 80 92 TINE - COUNTERCLOCKWISE TWIST9100206 62 80 92 SPRING WASHER202851 62 80 92 BOLT00756105 62 80 92 LOCKING NUT

5 06.950.01 44 56 64 PLATE - TINE SPACER9100206 44 56 64 SPRING WASHER202851 44 56 64 BOLT00756105 44 56 64 LOCKING NUT

6 852053 1 - - ROTOR SHAFT - REAR (2000 UNIT)852052 - 1 - ROTOR SHAFT - REAR (2600 UNIT)852039 - - 1 ROTOR SHAFT - REAR (3000 UNIT)

7 552117 1 1 1 COLLER10 41895.01 10 13 15 TINE - CLEARING LH - LONG

9100206 10 13 15 SPRING WASHER202851 10 13 15 BOLT00756105 10 13 15 LOCKING NUT

11 41895.02 10 13 15 TINE - CLEARING RH - LONG9100206 10 13 15 SPRING WASHER202851 10 13 15 BOLT00756105 10 13 15 LOCKING NUT

20 221035 4 4 4 COLLAR22 223051 2 2 2 SEAL23 222156 4 4 4 SNAP RING24 852049 2 2 2 HOUSING - BEARING

00003500 2 2 2 GREASE FITTING25 243687 2 2 2 BEARING26 3830213 1 1 1 PLATE STRUT

00756373 4 4 4 BOLT9143007 8 8 8 LOCKING NUT00765901 3 3 3 BOLT

28 243683 2 2 2 BEARING ASSEMBLY- FLANGED02957275 8 8 8 BOLT9143007 8 8 8 LOCKING NUT

29 852022 2 2 2 DUST COVER



2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07



2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07




3 06.949.01 62 80 92 TINE - CLOCKWISE TWIST9100206 62 80 92 SPRING WASHER202851 62 80 92 BOLT00756105 62 80 92 LOCKING NUT

4 06.949.02 62 80 92 TINE - COUNTERCLOCKWISE TWIST9100206 62 80 92 SPRING WASHER202851 62 80 92 BOLT00756105 62 80 92 LOCKING NUT

5 06.950.01 44 56 64 PLATE - TINE SPACER9100206 44 56 64 SPRING WASHER202851 44 56 64 BOLT00756105 44 56 64 LOCKING NUT


7 552117 1 1 1 COLLAR10 41895.01 10 13 15 TINE - CLEARING LH - LONG


11 41895.02 10 13 15 TINE - CLEARING RH - LONG9100206 10 13 15 SPRING WASHER202851 10 13 15 BOLT00756105 10 13 15 LOCKING NUT

20 221035 2 2 2 COLLAR22 223051 4 4 4 SEAL23 222156 4 4 4 SNAP RING24 852049 2 2 2 HOUSING - BEARING

00003500 2 2 2 GREASE FITTING25 243687 2 2 2 BEARING26 3830213 1 1 1 PLATE STRUT



29 852022 2 2 2 DUST COVER



2400, 3000, 3400 ROTOR SHAFT& BEARING ASSEMBLIES



2400, 3000, 3400 ROTOR SHAFT& BEARING ASSEMBLIES




3 552001 62 80 92 TINE - CLOCKWISE TWIST9100206 62 80 92 SPRING WASHER202851 62 80 92 BOLT00756105 62 80 92 LOCKING NUT

4 552002 62 80 92 TINE - COUNTERCLOCKWISE TWIST9100206 62 80 92 SPRING WASHER202851 62 80 92 BOLT00756105 62 80 92 LOCKING NUT

5 552016 44 56 64 PLATE - TINE SPACER9100206 44 56 64 SPRING WASHER202851 44 56 64 BOLT00756105 44 56 64 LOCKING NUT


7 552117 1 1 1 COLLAR10 552005 10 13 15 TINE - CLEARING LH - LONG


11 552006 10 13 15 TINE - CLEARING RH - LONG9100206 10 13 15 SPRING WASHER202851 10 13 15 BOLT00756105 10 13 15 LOCKING NUT

20 221035 2 2 2 COLLAR22 223051 - - - SEAL23 222156 - - - SNAP RING24 852049 - - - HOUSING - BEARING

00003500 - - - GREASE FITTING25 243687 - - - BEARING26 852078 1 1 1 STRUT-BRG HOUSING (BOLT ON)



29 852022 2 2 2 DUST COVER



4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07




ITEM PART NO. 4000 QTY 5000 QTY DESCRIPTION

1 552015 2 2 SPACER2 852084 2 - ROTOR SHAFT - FRONT (4000 UNIT ONLY)

3830200 - 1 ROTOR SHAFT - FRONT RH (5000 UNIT ONLY)852063 - 1 ROTOR SHAFT - FRONT LH (5000 UNIT ONLY)

3 06.949.01 122 152 TINE - CLOCKWISE TWIST9100206 122 152 SPRING WASHER202851 122 152 BOLT00756105 122 152 LOCKING NUT

4 06.949.02 122 152 TINE - COUNTERCLOCKWISE TWIST9100206 122 152 SPRING WASHER202851 122 152 BOLT00756105 122 152 LOCKING NUT

5 06.950.01 84 104 PLATE - TINE SPACER9100206 84 104 SPRING WASHER202851 84 104 BOLT00756105 84 104 LOCKING NUT

6 852083 1 - ROTOR SHAFT - REAR RH (4000 UNIT ONLY)852082 1 - ROTOR SHAFT - REAR LH (4000 UNIT ONLY)3830201 - 2 ROTOR SHAFT - REAR (5000 UNIT ONLY)

7 552117 2 2 COLLAR20 221035 4 4 COLLAR22 223051 4 4 SEAL23 222156 8 8 SNAP RING24 852049 4 4 HOUSING - BEARING

00766457 4 4 GREASE FITTING (METRIC)00003500 4 4 GREASE FITTING (NPT)

25 243687 4 4 BEARING26 3830213 2 2 PLATE STRUT

00756373 8 8 BOLT9143007 16 16 LOCKING NUT00765901 6 6 BOLT

28 852067 4 4 BEARING HOUSING ASSY (INC 29,30)9313087 8 8 BOLT9143007 8 8 LOCKING NUT

29 852003 4 4 BEARING HOUSING9313056 8 8 BOLT9100206 8 8 SPRING WASHER00766457 4 4 GREASE NIPPLE

30 552081 4 4 BEARING ASSEMBLY31 3836800 4 4 SEAL

IF EQUIPED WITH WITH CLEARING TINES:10 41895.01 20 25 TINE - CLEARING LH - LONG

9100206 20 25 SPRING WASHER202851 20 25 BOLT00756105 20 25 LOCKING NUT

11 41895.02 20 25 TINE - CLEARING RH - LONG9100206 20 25 SPRING WASHER202851 20 25 BOLT00756105 20 25 LOCKING NUT






3830200 - 1 ROTOR SHAFT - FRONT RH (5000 UNIT ONLY)852063 - 1 ROTOR SHAFT - FRONT LH (5000 UNIT ONLY)

3 06.949.01 122 152 TINE - CLOCKWISE TWIST9100206 122 152 SPRING WASHER202851 122 152 BOLT00756105 122 152 LOCKING NUT

4 06.949.02 122 152 TINE - COUNTERCLOCKWISE TWIST9100206 122 152 SPRING WASHER202851 122 152 BOLT00756105 122 152 LOCKING NUT

5 06.950.01 84 104 PLATE - TINE SPACER9100206 84 104 SPRING WASHER202851 84 104 BOLT00756105 84 104 LOCKING NUT


7 552117 2 2 COLLAR10 41895.01 20 25 TINE - CLEARING LH - LONG


11 41895.02 20 25 TINE - CLEARING RH - LONG9100206 20 25 SPRING WASHER202851 20 25 BOLT00756105 20 25 LOCKING NUT

20 221035 4 4 COLLAR22 223051 8 8 SEAL23 222156 8 8 SNAP RING24 852049 4 4 HOUSING - BEARING

00003500 4 4 GREASE FITTING25 243687 4 4 BEARING26 3830213 2 2 PLATE STRUT




30 552081 4 4 BEARING ASSEMBLY



4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLIES



4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLIES



852062 - 1 ROTOR SHAFT - FRONT LH (5000 UNIT ONLY)852063 - 1 ROTOR SHAFT - FRONT RH (5000 UNIT ONLY)

3 552001 122 140 TINE - CLOCKWISE TWIST9100206 122 140 SPRING WASHER202851 122 140 BOLT00756501 122 140 LOCKING NUT

4 552002 122 140 TINE - COUNTERCLOCKWISE TWIST9100206 122 140 SPRING WASHER202851 122 140 BOLT00756501 122 140 LOCKING NUT

5 552016 84 96 PLATE - TINE SPACER9100206 84 96 SPRING WASHER202851 84 96 BOLT00756501 84 96 LOCKING NUT


7 552117 2 2 COLLAR10 552005 20 23 TINE - CLEARING LH - LONG


11 552006 20 23 TINE - CLEARING RH - LONG9100206 20 23 SPRING WASHER202851 20 23 BOLT00756501 20 23 LOCKING NUT

20 221035 4 4 COLLAR22 223051 - - SEAL23 222156 - - SNAP RING24 852049 - - HOUSING - BEARING

00003500 - - GREASE FITTING25 243687 - - BEARING26 852078 2 2 STRUT-BRG HOUSING (BOLT ON)




30 552081 4 4 BEARING ASSEMBLY



6000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07



6000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07


1 552015 2 SPACER2 3830227 1 ROTOR SHAFT - FRONT RH WITH DUPLEX DRIVE ON SHORT SHAFT* 3830301 1 ROTOR SHAFT FRONT RH WITH TRIPLEX DRIVE

3830228 1 ROTOR SHAFT - FRONT LH WITH DUPLEX DRIVE ON SHORT SHAFT* 3830302 1 ROTOR SHAFT FRONT LH WITH TRIPLEX DRIVE3 06.949.01 174 TINE - CLOCKWISE TWIST


4 06.949.02 176 TINE - COUNTERCLOCKWISE TWIST9100206 176 SPRING WASHER202851 176 BOLT00756105 176 LOCKING NUT

5 06.950.01 120 PLATE - TINE SPACER9100206 120 SPRING WASHER202851 120 BOLT00756105 120 LOCKING NUT

6 3830226 2 ROTOR SHAFT - REAR WITH DUPLEX DRIVE ON SHORT SHAFT)* 3830303 2 ROTOR SHAFT REAR WITH TRIPLEX DRIVE7 552117 2 COLLAR11 41895.02 4 TINE - CLEARING RH - LONG ( LEFT HAND END OF RIGHT HAND REAR

ROTAR ONLY)9100206 4 SPRING WASHER202851 4 BOLT00756105 4 LOCKING NUT

20 3832516 8 COLLAR22 223051 8 SEAL23 222156 8 SNAP RING24 852049 4 BEARING HOUSING

00003500 4 GREASE FITTING25 243687 4 BEARING26 3830213 2 PLATE STRUT

00756373 8 BOLT9143007 16 LOCKING NUT00765901 6 BOLT

28 3830115 4 INNER BEARING HOUSING ASSY (INC 29,30)9313087 8 BOLT9143007 8 LOCKING NUT

29 3830284 4 INNER BEARING HOUSING9313056 8 BOLT9100206 8 SPRING WASHER

30 552081 4 BEARING ASSEMBLY31 3838200 4 O-RING

IF EQUIPED WITH CLEARING TINES:10 41895.01 27 TINE,LH CRANK 50 X 35111 41895.02 27 TINE,RH CRANK 50 X 351

9100206 54 WASHER,LOCK 12MM202851 54 HHCS M12 X 1.25 X 42 GR.8.800756105 54 NUT,TOPLOCK METRIC 12MM-P1.25

* REPLACES SHORT SHAFT IF USING TRIPLEX DRIVE



CRUMBLER 3000 Rev 04-04





1 243682 2 BEARING ASSY. - FLANGED W/SHIELDS3834879 4 SHIELD02959661 4 BOLT00762401 4 BOLT00756164 8 LOCKING NUT00771054 2 DECAL - GREASE00766457 2 GREASE FITTING243689 RP BEARING

3 852011 1 ARM - TRAILING LH852012 1 ARM - TRAILING RH

4 852029 2 PIN61368C8 2 BOLT00755954 2 SPRING WASHER00754583 2 FLATWASHER700116C 2 NUT

7 852016 1 CRUMBLER, ROLLER (2000 UNIT)852023 1 CRUMBLER, ROLLER (2600 UNIT)852024 1 CRUMBLER, ROLLER (3000 UNIT)

8 852000 2 PIN214241 2 FLATWASHER00036900 2 COTTER PIN212420 2 NUT - SLOTTED

9 00766457 2 FITTING



CRUMBLER 2000, 2600, 3000 Rev 04-04



CRUMBLER 2000, 2600, 3000 Rev 04-04


1 852013 2 COVER BEARING02959661 4 BOLT00762401 4 BOLT00756164 8 LOCKING NUT00771054 2 DECAL - GREASE00766457 2 GREASE FITTING

2 243682 2 BEARING ASSY - FLANGED243689 RP BEARING





9 00766457 2 FITTING



CRUMBLER 2400, 3000, 3400 Rev 04-04



CRUMBLER 2400, 3000, 3400 Rev 04-04


1 852013 2 COVER BEARING02959661 4 BOLT00762401 4 BOLT00756164 8 LOCKING NUT00771054 2 DECAL - GREASE00766457 2 GREASE FITTING



4 852029 2 PIN00754764 2 BOLT00754577 2 SPRING WASHER00754583 2 FLATWASHER



9 00766457 2 FITTING



CRUMBLER 4000 - 5000





1 243683 2 BEARING ASSY. - FLANGED W/SHIELDS3834878 4 SHIELD02957275 8 BOLT9143007 8 LOCKING NUT00771054 2 DECAL - GREASE00766457 2 GREASE FITTING243690 RP BEARING



7 3830212 1 CRUMBLER, ROLLER (4000 UNIT)41.130.01 1 CRUMBLER, ROLLER (5000 UNIT)


9 00766457 2 FITTING





1 852059 2 COVER BEARING02957275 8 BOLT9143007 8 LOCKING NUT00771054 2 DECAL - GREASE00766457 2 GREASE NIPPLE




7 3830212 1 CRUMBLER, ROLLER (4000 UNIT)41.130.01 1 CRUMBLER, ROLLER (5000 UNIT)


9 00766457 2 FITTING





1 852059 2 COVER BEARING02957275 8 BOLT9143007 8 LOCKING NUT00771054 2 DECAL - GREASE00766457 2 GREASE NIPPLE



4 852029 2 PIN00754764 2 BOLT00754577 2 SPRING WASHER00754583 2 FLATWASHER

7 852085 1 CRUMBLER, ROLLER (4000 UNIT)852026 1 CRUMBLER, ROLLER (5000 UNIT)


9 00766457 2 FITTING





1 243683 4 BEARING ASSY. - FLANGED W/SHIELDS3834878 8 SHIELD02957275 16 BOLT9143007 16 LOCKING NUT243690 RP BEARING

3 3830207 1 ARM - TRAILING LH3830206 1 ARM - TRAILING RH (NOT SHOWN)


5 3830209 1 PLATE - DEPTH ADJUST LH214224 2 WASHER00762395 2 BOLT9100206 2 SPRING WASHER

6 3830237 1 CRUMBLER ROLLER, LH7 3830236 1 CRUMBLER ROLLER, RH8 3830238 1 CENTER ARM9 3830253 1 PIN - CENTER ARM PIVOT10 3832515 1 BUSHING, THREADED FLANGE11 3830208 2 PLATE - DEPTH ADJUST RH12 3832600 1 PIN, HEX ADJUSTMENT13 701613C 1 LOCKWASHER14 02959661 1 BOLT15 3830244 2 COVER16 212420 3 NUT

00036900 3 COTTER PIN17 214241 3 FLATWASHER18 3830239 1 PIN - CENTER ARM19 852058 2 PIN - OUTER ARM20 00766457 7 GREASE FITTING





1 852059 2 COVER BEARING02957275 16 BOLT9143007 16 LOCKING NUT


3 3830207 1 ARM - TRAILING LH3830206 1 ARM - TRAILING RH (NOT SHOWN)


5 3830209 1 PLATE - DEPTH ADJUST LH214224 2 WASHER00762395 2 BOLT9100206 2 SPRING WASHER

6 3830237 1 CRUMBLER ROLLER, LH7 3830236 1 CRUMBLER ROLLER, RH8 3830238 1 CENTER ARM9 3830253 1 PIN - CENTER ARM PIVOT10 3832515 1 BUSHING, THREADED FLANGE11 3830208 2 PLATE - DEPTH ADJUST RH12 3832600 1 PIN, HEX ADJUSTMENT13 701613C 1 LOCKWASHER14 02959661 1 BOLT15 3830244 2 COVER16 212420 3 NUT

00036900 3 COTTER PIN17 214241 3 FLATWASHER18 3830239 1 PIN - CENTER ARM19 852058 2 PIN - OUTER ARM20 00766457 7 GREASE FITTING



REAR FLAP - MODEL 4000 & 5000


1 00011100 36 38 FLATWASHER2 00011400 13 13 BOLT4 3831151 2 - REAR FLAP RETAINING STRAP

3831152 - 2 REAR FLAP RETAINING STRAP3831156 - - REAR FLAP RETAINING STRAP

5 3836100 2 - REAR DOOR BELTING3836101 - 2 REAR DOOR BELTING3836102 - - REAR DOOR BELTING

6 3837420 4 4 SUPPORT SPRING7 600315 12 12 SUPPORT CLAMP8 6D9017 35 37 LOCKNUT



REAR FLAP - MODEL 6000


1 3830254 1 REAR FLAP - LH2 3830245 1 REAR FLAP - RH3 6D9017 36 LOCKNUT4 600315 18 SUPPORT CLAMP5 00011100 36 FLAT WASHER6 3837420 6 SUPPORT SPRING7 3836102 2 REAR DOOR BELTING8 3831156 2 REAR FLAP RETAINING STRAP9 00011400 18 BOLT



LIGHT KIT - MODEL 4000, 5000 & 6000


1 2431606 4 LIGHT MOUNT BRACKET2 3830285 4 LIGHT BRACKET3 00015800 18 LOCKNUT4 00011400 8 HEXBOLT5 02816800 4 HEXNUT6 370013C 4 LOCKWASHER7 33105C 4 HEX JAMNUT8 1458398 4 ORANGE REFLECTOR9 1458392 4 RED REFLECTOR10 00011100 18 FLATWASHER11 2467901 2 DUAL RED/BLACK SIGNAL LAMP12 2467900 2 DUAL AMBER/AMBER LAMP13 2457900 1 MAIN WIRING HARNESS14 2467903 1 PLUG HOLDER15 2467902 1 WISHBONE HARNESS - 7’16 2467905 2 EXTENSION HARNESS - 5’

2467906 2 EXTENSION HARNESS - 7’17 3263N13C 4 SCREW18 329023C 6 LOCKNUT19 3263N6C 2 SCREW20 2417903 4 GROUND WIRE21 0138629 12 TY-WRAP22 3831733 2 WIRE COVER (NOT SHOWN)



SIGNAL LAMPS - DUAL (AMBER)


1 2417900 2 AMBER SIGNAL LAMP LENS2 1417918 1 LIGHT BULB3 02816800 1 HEXNUT4 33105C 1 JAMNUT5 370013C 1 WASHER6 2417903 1 8" GROUND WIRE ASSEMBLY



SIGNAL LAMPS - DUAL (RED)


1 2417901 1 RED SIGNAL LAMP LENS2 2417902 1 BLACK (BLANK) SIGNAL LENS3 1417918 1 LIGHT BULB4 02816800 1 HEXNUT5 33105C 1 JAMNUT6 370013C 1 WASHER7 2417903 1 8" GROUND WIRE ASSEMBLY



GREASE LINES AND SHIELDS - MODEL 6000


1 3831615 2 LEFT FRONT & RIGHT REAR OUTER SHIELD2 3831614 2 RIGHT FRONT & LEFT REAR OUTER SHIELD3 3831617 4 CENTER SHIELD4 3831616 2 OUTER TOP SHIELD5 3831732 1 CENTER TOP SHIELD6 3830118 4 GREASE LINE - 28"7 3830119 4 GREASE LINE - 42"



TRIPLEX DRIVE TRANSMISSION ASSY 6000 S/N 10095 -Current Pub 08-06



TRIPLEX DRIVE TRANSMISSION ASSY 6000 S/N 10095 -Current Pub 08-06


1 3836200 2 ROLLER CHAIN2 3836351 2 SPROCKET3 3812500 2 SPACER, FRONT SHAFT (USED ONLY ON TRIPLEX DRIVE ON SHORTER

SHAFTS4 552214 2 WASHER,SPECIAL FLAT5 701615C 2 M16 LOCKWASHER6 02961833 2 BOLT (USED ONLY WITH ITEMS 3 & 8)7 3836350 2 SPROCKET8 3812501 2 SPACER, REAR SHAFT (USED ONLY ON TRIPLEX DRIVE ON SHORTER

SHAFTS9 552215 2 WASHER,FLAT.10 3830295 1 TENSIONER BRACKET - LH11 3830294 1 TENSIONER BRACKET - RH12 3830292 2 ROD SPRING GUIDE13 212419 4 HEX LOCKNUT M16 X 1.514 552008 2 NUT,SPECIAL M16 X 1.5 X 6215 15B1600 2 WASHER 1 SAE P16 3837421 2 SPRING,HD COMPRESSION17 3830293 2 BRACKET TENSIONER18 3836775 6 TENSIONER,NYLON19 312017H5C 4 HEX CAP 3/8-16 X 4 GR.520 00015800 4 NUT,TOPLOCK 3/8NC PLB21 0401225 2 25MM DIA. EXTERNAL SNAP RING22 3832525 2 PIN23 214224 2 WASHER,FLAT 13 X 44.5 X 524 9313056 2 HEXB METRIC 12-P1.75- 25MM PL525 9100206 2 WASHER,LOCK 12MM30 1458430 4 WASHER,MACHINERY BUSHING - YDP



LIMITED WARRANTY

1. LIMITED WARRANTIES1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal

purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)that the goods purchased are free from defects in material or workmanship.

1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to bedefective under normal use and service due to defects in material or workmanship.

1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, orlubricants, or which has served its normal life. This limited warranty does not apply to any part of any internalcombustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically foundin your Operator’s Manual.

1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of anynature on behalf of Manufacturer.

2. REMEDIES AND PROCEDURES.2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer

within 30 days of purchase.2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the

goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which theclaim is based.

2.03.Purchaser is responsible for returning the goods in question to the Dealer.2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and

service due to defects in material or workmanship, Manufacturer will:(a) Repair or replace the defective goods or part(s) or(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)

if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warrantyby Manufacturer.

The choice of remedy shall belong to Manufacturer.2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and

for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-portation cost for the goods or part(s) from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES

WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE.

3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FORUSE OF THE GOODS.

3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TOPURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGECAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOTLIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROMTHE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THEABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGESINCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.

3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDERTHIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HASOCCURRED.

4. MISCELLANEOUS.4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,

Texas.4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall

be deemed to be a waiver of any other term.4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the

invalidity of such provision shall not invalidate any other provisions herein.4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machineidentification when applying for warranty.

M&W Implement Model _____________________________________ Serial Number________________________________

Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION:READ YOUR OPERATOR'S MANUAL M&W

An Alamo Group Company1020 South Sangamon Ave.

Gibson City, Illinois 60936217-784-4261

M&W

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions andthe Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easilyfind the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safetyrequirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and3. Ensure that each employee uses such Seatbelt while the tractor is moving; and4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected

area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.2. Where possible, avoid operating the tractor near ditches, embankments, and holes.3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.4. Stay off slopes too steep for safe operation.5. Watch where you are going - especially at row ends, on roads, and around trees.6. Do not permit others to ride.7. Operate the tractor smoothly - no jerky turns, starts, or stops.8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machineryguards in place...

Please work, drive, play and live each day with care and concern foryour safety and that of your family and fellow citizens.

Printed U.S.A.Dyna-Driver 08-06 P/N 00771093P

1348 1548 1948 pub 05-04 covers - earthmaster |...

Documents