122319 logia 5-in-1 wireless weather station with wi-fi

5-IN-1 WIRELESSWEATHER STATION WITH WI-FIUSER GUIDELOWSC510WB

2

Thank you for purchasing the Logia™ 5-in-1 Wireless Weather Station with WI-FI. This User Guide is intended to provide you with guidelines to ensure that operation of this product is safe and does not pose risk to the user. Any use that does not conform to the guidelines described in this User Guide may void the limited warranty.Please read all directions before using the product and retain this guide for reference. This product is intended for household use only. It is not intended for commercial use.This product is covered by a limited one-year warranty. Coverage is subject to limits and exclusions. See warranty for details.

SAFETY PRECAUTIONSPRODUCT FEATURESPACKAGE CONTENTSDISPLAY CONSOLE OVERVIEWLCD DISPLAY OVERVIEWWIRELESS WEATHER SENSOR OVERVIEWWIRELESS WEATHER SENSOR SETUPDISPLAY CONSOLE SETUPWI-FI CONNECTIONCREATE WEATHER SERVER ACCOUNTACCESSING WEATHER DATA ONLINEOTHER CONSOLE SETTINGS AND FUNCTIONS CARE AND MAINTENANCESPECIFICATIONSQUESTIONS?

345678

101315202324343539

TABLE OF CONTENTS

3

SAFETY PRECAUTIONS1. Do not let children use or play with this device. It is not a toy.2. Do not use any attachments not supplied or recommended by the manufacturer.3. Do not place the appliance near open flames or heat sources. Fire, electric shock, product damage,

or injury might occur.4. Do not mix old and new batteries in the display unit.5. A low battery symbol will appear in the OUT or CH sections of the LCD display when battery

power is low on the console or weather sensor, respectively. Be sure to change the batteries promptly to ensure the proper operation of the weather station.

6. Do not subject the display unit to excessive force or shock (do not throw the unit!), dust, extreme high or low temperatures, or humidity/moisture. These can cause the unit to stop functioning as well as present the risk of shock, fire, or other hazards.

7. Do not cover the ventilation holes on the display with newspapers, curtains, or any other items. 8. Never immerse the display in water! If you spill any liquid on the display, dry it immediately with a

soft, lint-free cloth.9. Do not use abrasive or corrosive materials to clean the display. 10. Do not tamper with the display or the weather vane’s internal components. This invalidates your

limited warranty. 11. Placing this product on certain types of wood may result in unintended damage to the finish,

for which Logia™ will not be responsible. Consult your furniture manufacturer’s instructions for information on wood care.

12. Do not dispose of old batteries as unsorted municipal waste. Make sure to dispose of them properly according to your local guidelines.

13. The main display console is only intended for use indoors.

QUESTIONS OR PROBLEMS? CONTACT US!Email: [email protected] or call: 1-833-815-0568 www.logiaweatherstation.com

4

PRODUCT FEATURES1. Wireless 5-in-1 weather sensor measures wind speed, wind direction, rainfall, temperature, and

humidity.2. No calibration needed! The product is fully pre-calibrated and mostly assembled; all you need to do

is install it and sync with the included display console.3. Provides precise weather and environmental information directly from your own backyard, instead

of relying on a national weather station.4. Color LCD display with dimmable backlight.5. Can alert you to excessively high/low indoor or outdoor temperatures or humidity, high wind speeds,

extreme drops in barometric pressure, high heat indexes, low wind chills, and high/low dew points.6. Syncs with installed WI-FI and online weather servers (Weather Undergound and Weathercloud) to

help you store and track weather data in your area, plus view live weather statistics and historical weather trends.

5

PACKAGE CONTENTS

WI-FI

SENSOR RESETREFRESH

MAX/MINHISTORYCHANNEL

BARO

UNIT

1. Wireless Weather Sensor (1)2. Mounting Pole (1)

Plastic Exterior3. Mounting Clamp (1)4. Mounting Base (1)5. Large Mounting Screws (4)

6. Large Hexagonal Nuts (4)7. Large Washers (4)8. Small Screws (2)9. Small Hexagonal Nuts (2) 10. Rubber Pads for Mounting

Clamp

11. Display Console with Kickstand (1) 12. Display Console Battery (1)13. Display Console Power Cable (1)14. User Guide

1

2

5

7

8

6

9

4

3

10

11

12

13

14

6

DISPLAY CONSOLE OVERVIEWMAIN CONSOLE OVERVIEW

1. Kickstand2. SNOOZE button3. CHANNEL button4. HISTORY button5. MAX/MIN button6. WIND button7. INDEX button8. BARO button9. RAIN button

10. LCD Display (See overview on page7

11. CLOCK SET button12. ALARM button13. Wall mount notch14. ALERT button15. button16. button17. Power connection

18. 12/24 button19. °C/°F button20. BARO UNIT button21. SENSOR/WI-FI button22. REFRESH button23. Battery compartment24. OFF/LO/HI button25. RESET button

WI-FI

SENSOR RESETREFRESH


BARO

UNITWI-FI

SENSOR RESETREFRESH


BARO

UNIT

1

2

3 4 5 6 7 8 9 10 17 18 19 20 21 22 23 24 25

11 12 13 14 15 16

7

LCD DISPLAY OVERVIEW

1. Temperature & humidity (indoor/CH)2. Weather forecast3. Time, date, & moon phase4. Wind speed & direction5. Temperature & humidity (outdoor)6. Barometer7. Rainfall 8. Weather index

LCD DISPLAY Display section:1. Indoor / CH temperature &

humidity2. Weather forecast3. Time, calendar & moon phase4. Wind direction & speed5. Outdoor temperature &

humidity6. Barometer7. Rainfall8. Weather index

WIRELESS 5-IN-1 WEATHER SENSOR1. Rain collector2. Balance indicator3. Antenna4. Wind cups5. Mounting pole6. Radiation shield7. Wind vane8. Mounting base9. Mounting clamp10. Red LED indicator11. [ RESET ] key12. Battery door13. Screws

1

2

3

5

89

4

76

12

10

11

13

1

4

5

6

7

8

2

3

8

WIRELESS WEATHER SENSOR OVERVIEWMAIN DEVICE

1. Rain collector2. Level3. Antenna4. Wind cups (anemometer)5. Mounting pole6. Sensor casing7. Wind vane

8. Mounting base9. Mounting clamp10. Red LED indicator11. RESET button12. Battery compartment13. Mounting clamp

screws

1

4

2

6

3

710

11

12

5

138

9

9

RAIN GAUGE

TEMPERATURE AND HUMIDITY SENSOR

WIND SENSOR

1. Rain collector2. Tipping bucket3. Drain holes4. Rain sensor

1. Sensor shield2. Temperature and

humidity sensor

1. Wind cups (anemometer)2. Wind vane

1

1

1

2

2

2

3 4

10

WIRELESS WEATHER SENSOR SETUPINSTALL BATTERIES

ASSEMBLE STAND AND POLE

1. Unscrew the door to the battery compartment on the underside of the main sensor unit.2. Insert three (3) new AA alkaline batteries, making sure the polarities match up with the markings

inside the compartment.

1. Insert the top of the pole into the square hole at the bottom of the weather sensor. Ensure that the arrow indicators are lined up as shown.

3. Replace the battery door, ensuring the watertight O-ring is properly aligned. This maintains the water-resistant seal.

4. Replace the battery screw, making sure it is tightly fastened down. The red LED should begin fl ashing every 12 seconds.

11

2. Insert the nut into the hexagonal hole by the sensor and hold it in place, then insert the screw through the other side. Use a screwdriver to tighten the screw. Do not insert the screw fi rst, or the nut may not line up correctly with the designated hole.

3. Insert the bottom of the pole into the square hole on the plastic stand, making sure the arrows are lined up as shown.

Please note that there are two diff erent ways you can attach the pole to the base, depending on how you will be mounting it outdoors. If you will be fastening the sensor directly to a railing, use the option that positions the stand perpendicular to the sensor pole. If you will be fastening it to a pole, use the slot that positions the base parallel to the sensor pole.

4

BATTERY AND INSTALLATION

Unscrew the battery door at bottom of unit and insert the batteries according to the +/- polarity indicated .Screw the battery door compartment on tightly .

NOTE:1 . Ensure the water tight O-ring is properly aligned in place to ensure water resistant .2. The red LED will begin flashing every 12 seconds.

ASSEMBLY THE STAND AND POLE

Step 1Insert the top side of the pole to the square hole of the weather sensor .

NOTE: Ensure the pole and sensor's indicator align .

Step 2Place the nut in the hexagon hole on the sensor, then insert the screw in other side and tighten it by the screw driver .

Step 3Insert the other side of the pole to the square hole of the plastic stand .

NOTE: Ensure the pole and stand's indicator align .

12

MOUNT THE SENSOR OUTDOORS

If securing to a railing, make sure the railing is made of suitable material, and screw directly through the openings in the base stand into the railing until secure.

1. The wireless weather sensor should be mounted in an open area with no obstructions above and/or around it, so that it can accurately measure the rain and wind.

2. The wind vane should be pointed due North (refer to the arrow on top of the unit) in order to be properly oriented and receive accurate wind readings.

3. The mounting stand and included clamps should be secured to a post or pole, with a minimum of 4.9 ft. (1.5 m) ground clearance.

4. If securing to a pole, make sure you add the rubber pads to the clamp before fastening it with the included screws. The pole should be between 1″-1.3″ in diameter.

4. Insert the nut into the hexagonal hole on the side of the stand and hold it in place, then insert the screw through the other side. Use a screwdriver to tighten the screw.

5

Step 4Place the nut in the hexagon hole of the stand, then insert the screw in other side and then tighten it by the screw driver .

Install the wireless 5-IN-1 sensor in an open locat ion with no obstructions above and around the sensor for accurate rain and wind measurement . Install the sensor with the smaller end facing the North to properly orient the wind direction vane .Secure the mounting stand and clamps (included) to a post or pole, and allow minimum 1 .5m off the ground .

1 .5 meter offthe ground

Add rubberpads beforemount on the pole

Point toNORTH

MOUNTING GUIDELINES1 . Install the wireless 5-IN-1 sensor at least 1 .5m off the ground for better and more accurate

wind measurements .2 . Choose an open area within 150 meters from the LCD console .3 . Install the wireless 5-IN-1 sensor as level as possible to achieve accurate rain and wind

measurements .4 . Mount the wireless 5-IN-1 sensor with the wind meter end pointing to the North to correctly

orient direction of the wind vane .

A . Mounting on pole (Pole Diameter 1"~1 .3")(25~33mm)

B . Mounting on the railing

5

Install the wireless 5-IN-1 sensor in an open location with no obstructions above and around the sensor for accurate rain and wind measurement. Install the sensor with the smaller end facing the North to properly orient the wind direction vane.Secure the mounting stand and bracket (included) to a post or pole, and allow minimum 1.5m off the ground.

1.5 meter offthe ground


Point toNORTH

POWER UP CONSOLEYour console can pairing up with the wireless 5-IN-1 outdoor weather sensor and up to 7 optional wireless sensors. (Not included)

INSTALL THE BACKUP BATTERY

1 . Remove the battery door of the console.2 . Insert a new button cell battery.3 . Replace the battery door.

NOTE:The backup battery can backup: Time & Date, Max/Min & Past 24 hours weather records, Alert setting values, offset value of weather data and Sensor(s) channel history.The built-in memory can backup: Router setting and Weather server setting

POWER UP THE CONSOLE1 . Plug the power adaptor to power up the console.2 . Once the console power up, all the segments of the LCD will be shown.3 . The console will automatically start AP mode.

NOTE: If no display appears on the LCD after you plug the adaptor, press [ RESET ] key by using a pointed object.

SET LCD DISPLAY VIEWING ANGLEPress [ ] or [ ] key in normal mode to adjust LCD viewing angle to fit table stand or wall mount situation.

A MOUNTING ON POLE(POLE DIAMETER 1”-1.3”)(25-33MM)

Point to NORTH

Add rubber pads before mount onthe pole

1.5 meter off the ground

13

INSTALLING THE BACKUP BATTERY

POWERING THE DISPLAY CONSOLE

Your display console can pair with the wireless weather sensor as well as up to seven (7) optional wireless hygro-thermo outdoor sensors (not included).

5. The mounting location should be within 492 ft. (150 m) of the location where you will be keeping the display console with few obstructions and relatively clear sightlines. If there are multiple walls/ levels/buildings in between the sensor and the display console, the functionality could be compromised and you will need less space between the two. 6. Use the built-in level to make sure the sensor is parallel with the ground.

1. Detach the table stand.2. Unscrew the console battery door screw. 3. Remove the battery door.4. Insert a new button cell battery.5. Replace the battery door and tighten the screw. NOTE: The backup battery can assist with backing up the time & date, MAX/MIN data, weather records from the past 24 hours, alert settings, the offset value of weather data, and the sensor(s) channel history. The built-in memory will backup router and weather server settings.

1. Connect the power cable to a wall outlet or power source and to the display console power connection port.2. The display console should power on, and all the segments of the LCD display screen should be shown.3. The display console will automatically start AP mode.

DISPLAY CONSOLE SETUP5

Step 4Place the nut in the hexagon hole of the stand, then insert the screw in other side and then tighten it by the screw driver .

Install the wireless 5-IN-1 sensor in an open locat ion with no obstructions above and around the sensor for accurate rain and wind measurement . Install the sensor with the smaller end facing the North to properly orient the wind direction vane .Secure the mounting stand and clamps (included) to a post or pole, and allow minimum 1 .5m off the ground .

1 .5 meter offthe ground


Point toNORTH

MOUNTING GUIDELINES1 . Install the wireless 5-IN-1 sensor at least 1 .5m off the ground for better and more accurate

wind measurements .2 . Choose an open area within 150 meters from the LCD console .3 . Install the wireless 5-IN-1 sensor as level as possible to achieve accurate rain and wind

measurements .4 . Mount the wireless 5-IN-1 sensor with the wind meter end pointing to the North to correctly

orient direction of the wind vane .

A . Mounting on pole (Pole Diameter 1"~1 .3")(25~33mm)

B . Mounting on the railing

Screw

CR2032

B MOUNTING ON A RAILING

14

PAIRING THE WIRELESS WEATHER SENSOR WITH THE DISPLAY CONSOLE

SET THE LCD DISPLAY VIEWING ANGLE

CHANGING BATTERIES AND MANUAL PAIRING

Whenever you change the batteries in the sensor, you will need to manually repair it with the display console. Follow these instructions to manually pair your console with the sensor.

1. Once your display console powers on, it should automatically search for and connect to the wireless weather sensor. If the console does not connect within the fi rst 15 minutes, refer to the following section, Changing Batteries and Manual Pairing, for instructions on manual pairing.

2. You will see the icon of an antenna blinking in the temperature and humidity (outdoor) section of the display.

3. Once the pairing process completes, the antenna icon will appear solid (not blinking), and the readings for outdoor temperature and humidity, wind speed, wind direction, and rainfall will appear in their designated sections of the LCD display.

If you have the display console wall-mounted or on a table stand, the viewing angle may need adjustment. Press or buttons while the display is in normal operating mode to adjust the viewing angle.

NOTE: If nothing appears on the LCD display screen after you plug in the power adaptor, use a pin or similar small object to press the RESET button.

1. Change the batteries in the wireless weather sensor.2. Press the SENSOR/WI-FI button at the back of the console.3. Press the RESET key on the underside of the wireless weather sensor. Make sure after pressing

the RESET key that the red LED indicator is fl ashing every 12 seconds.

WI-FI

SENSOR RESETREFRESH


BARO

UNIT

3

1 2

15

PAIRING ADDITIONAL WIRELESS SENSORS WITH THE DISPLAY CONSOLE

NOTE: Any time you press the RESET key underneath the wireless weather sensor, it generates a new ID code for pairing with the console, and you will need to press the SENSOR/WI-FI button on the console for the two devices to pair again.

The display console should automatically search and pair with any additional wireless hygro-thermo outdoor sensors you install. You can also press the SENSOR/WI-FI button to search manually for the sensor while on the channel where it should display. Once your sensor has paired, the sensor signal strength indicator and weather information will appear in the temperature and humidity (outdoor) section when you are on the channel associated with that sensor.

WI-FI CONNECTIONSET UP WI-FI CONNECTION

When you fi rst power up the console, or press and hold the SENSOR/WI-FI button for six (6) seconds, the console LCD display will show the letters “AP” and an icon to signify that it has entered Access Point (AP) mode. At this time it will be ready for the WI-FI settings to be adjusted.

Use your smartphone, tablet, or computer to connect to the console via WI-FI by following these steps: 1. On PC, open your WI-FI network settings. On Android™ or iOS devices, go to settings menu and then select Connections/WI-FI to open the network settings. 2. Locate the display console’s SSID from the list. It should appear as PWS-XXXXXX (where all the X’s are integers) in the list. Tap on the SSID to connect. This step will take several seconds.

6

MAIN CONSOLE

Your main console can pairing up with the wireless 5-in-1 outdoor weather sensor and up to 7

optional wireless hygro-thermo outdoor sensors . (Not included)

Powering up the main console

1 . Remove the battery door on the back side of the main unit .

2 . Insert 6 new AA batteries and replace the battery door .

3 . Once the batteries are inserted, the segments of the LCD will be shown .

NOTE:If no display appears on the LCD after inserting the batteries, press [ RESET ] key by using a

pointed object .

Pairing of wireless 5-in-1 weather sensor with main console

After insertion of batteries, the main console will automatically search and connect the

wireless 5-in-1 sensor (antenna blinking) . Once the connection is successful, antenna mark

and readings for outdoor temperature & humidity, wind speed, wind direction and rainfall will

appear on the display .

Changing batteries and manual pairing of sensor

Whenever you changed the batteries of the wireless 5-in-1 sensor, pairing must be done

manually .

1 . Change all the batteries to new ones in the sensor .

2 . Press [ CH ] until the icon appear in the Outdoor section

3 . Press [ SENSOR / SYNC ] key .

4 . Press [ RESET ] key on the sensor .

NOTE:Pressing [ RESET ] key at bottom of wireless 5-in-1 sensor will generate a new ID code for

pairing purpose . So you also need to press the [ SENSOR / SYNC ] key on the console to

repairing up the sensor .

Pairing the wireless sensor(s) with the console

The console will automatically search and pair up your wireless sensor(s) . You can also press

[SENSOR / SYNC ] key to search the on display channel's sensor manually . Once your sensor

paired up, the sensor signal strength indicator and weather information will appear on your

console display .

SYNC UP PC TIME

This unit is designed to automatically synchronize its calendar and clock when connected to

the computer with PC software "Weather Tool" through USB data cable . Once connected to the

computer, the unit will automatically synchronize the time instantly and 12:00am per day . You

can also press the [ TIME SYNC ] key to sync up PC time instantly .

NOTE: - The time sync function only work with the PC software "Weather Tool", please make sure the

PC software is open .

- PC Time sync up is according to your current PC time, so please ensure your PC time is

correct . Once the PC time sync up the icon will appear in the Time section .

- You can also enable or disable auto time sync function by press and hold [ TIME SYNC ] key

for 8 seconds .

9

4 . Jot down your ID and key for the further setup step.

SETUP WI-FI CONNECTION1 . When you first power up the console, or press and hold the [ WI-FI / SENSOR ] key for 6

seconds in normal mode, the console LCD will show "AP" and " " icon to signify that it has entered AP (access point) mode, and is ready for WI-FI settings.

2 . Use the smart phone, tablet, or computer to connect to the console through WI-FI.3 . In PC choose WiFi network settings or In Android / iOS choose setting → WI-FI to select the

console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.

PWS-XXXXXX

PWS-XXXXXX

PC WI-FI network interface Android WI-FI network interface4 . Once connected, enter the following IP address into your internet browser’s address bar, to

access the console’s web interface:http://192.168.1.1

NOTE : - Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header. - Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or Opera.

9






PWS-XXXXXX

PWS-XXXXXX




16

3. Once you are connected to the display console, open up your internet or mobile web browser, and enter the following address into the address bar: http://192.168.1.1 (make sure to include the http:// or else the web browser may interpret the address as a search query). We recommend using the latest version of reputable web browsers.

SET UP WEATHER SERVER CONNECTION

Once you are connected via WI-FI to the display console and have opened the settings page at http://192.168.1.1, enter the following information into the web interface setup page. If you have chosen not to use Weather Underground or Weathercloud’s servers, leave the check boxes unchecked.

Function firmware version: 1.00 WiFi firmware version: 1.00

nist.time.govServer URL:

Time server setup

WIFI Router setup

SETUP ADVANCED

Wunderground

Station ID:

WDw124

******

******

******

IPACIR23Wc

Weather server setup

Station key:

Router:

Add Router

Search

Security type:

Router Password:

WAP2

ROUTER_A

Apply

Language: English

Weathercloud

Station ID:

Station key:

Mac address 00:0E:C6:00:07:10

Press to search router Select the WI-FI router (SSID) you will connect toManually enter the SSID if not on the listSelect router’s security type (usually WAP2)

Enter new Station ID and Station key assigned by Wunderground (Weather Underground)

Select time server

Press to complete the setting

SETUP page

Router’s password (leave blank if unsecured)

Press to allow add router manually

Password record remark (If you entered password)

Current ID and key recorded (if any)

Current ID and keyrecorded (if any)

Enter new Station ID and Station keyassigned by Weathercloud

Press “SETUP” icon to SETUP page

If you don’t have Station ID and Station Keys available for the upload you need to first create an account at the respective weather servers of Weather Underground (WU) and WeatherCloud (WC), followed by registering the product to obtain the ID and keys. For details, please refer to session on “CREATE WEATHER SERVER ACCOUNT”.

17

NOTES: When the WI-FI setup is complete, your computer or mobile device will return to the default WI-FI connection. If it does not, simply open your device’s wireless network settings and manually reconnect.While in AP mode, you can press and hold the SENSOR/WI-FI button for six (6) seconds to exit AP mode. The display console will simply restore the previous AP settings.

WI-FI CONNECTION STATUS

TIME SERVER CONNECTION STATUS

ADVANCED SETTINGS VIA WEB INTERFACE

The following icons on the LCD display screen show the WI-FI status:

Once the display console has connected to the internet, it will attempt to connect to the internet time server to obtain the UTC time. Once the connection is successful and the time has been updated, the “SYNC” icon will appear above the WI-FI icon on the LCD.

Once you are connected via WI-FI to the display console and have opened the settings page at http://192.168.1.1, clicking on the tab that says ADVANCED will open the following page. This page will allow you to set and view specific calibration data of your display console, and also update the firmware if you are on PC.

To display the correct time for your specific time zone, you’ll need to change the time zone in the CLOCK setting mode from 00 (default) to your specific time zone (e.g. -5 for EST). If you don’t know your time zone, you can look it up online. 1. In normal operating mode, press and hold the CLOCK SET button for two (2) seconds to enter the clock setting menu. 2. Press the or buttons to adjust the time zone, and then press and hold the CLOCK SET button for two (2) seconds to confirm and exit the menu. Please refer to the Setting the Time section of the manual on page 24 for details of other available clock settings.

The time will automatically sync with the internet time server at 12:00AM and 12:00PM each day. If you would like to force it to sync sooner than that, press the REFRESH button on the console to update the time in the next minute.

10

SETUP THE WEATHER SERVER CONNECTIONEnter the following information into the below web interface "SETUP" page. If you choose not to use Wunderground.com or Weathercloud.net, leave the check boxes unchecked.



Time server setup

WiFi Router setup

SETUP ADVANCED

Wunderground

Station ID:WDw124

******

******

******

IPACIR23Wc


Station key:

Router:

Add Router

Search

Security type:

Router Password:

WAP2

ROUTER_A

Apply

Language: English

Weathercloud

Station ID:

Station key:


Press to search router Select the Wi-fi router (SSID) you will connect toManually enter the SSID if not on the listSelect router’s security type (usually WAP2)

Check to confirm upload to Weather UndergroundEnter new Station ID and Station key assigned by Wunderground (Weather Underground)

Check to confirm upload to Weathercloud

Select time server


SETUP page







Solid: the display console isconnected to your wireless router

Flashing: the display console is attempting to connect to your wireless router

Flashing: the display console is currently in AP (access point) mode


NOTE: - When WI-FI setup is complete, your PC or mobile will resume your default WI-FI connection. - During AP mode, you can press and hold the [ WI-FI / SENSOR ] key for 6 seconds to stop AP mode and the console will restore your previous setting.

WI-FI CONNECTION STATUSBelow is the WI-FI icon status on the console LCD:

Flashing: Console is trying to connect to WI-FI router

TIME SERVER CONNECTION STATUSAfter the console has connected to the internet, it will attempt to connect to the internet time server to obtain the UTC time. Once the connection succeeds and the console's time has been updated, the “ ” icon will appear on the LCD.

Time zone: To display the time of your time-zone, change the time zone in CLOCK setting mode from '00' (default) to your time zone (e.g.08 for Hong Kong).1. Press and hold [ CLOCK SET ] key for 2s to enter time setting mode.2. Press [ ] or [ ] key to enter your time zone, then press and hold [ CLOCK SET ] key

setting for the console.

10

SETUP THE WEATHER SERVER CONNECTIONEnter the following information into the below web interface "SETUP" page. If you choose not to use Wunderground.com or Weathercloud.net, leave the check boxes unchecked.



Time server setup

WiFi Router setup

SETUP ADVANCED

Wunderground

Station ID:WDw124

******

******

******

IPACIR23Wc


Station key:

Router:

Add Router

Search

Security type:

Router Password:

WAP2

ROUTER_A

Apply

Language: English

Weathercloud

Station ID:

Station key:


Press to search router Select the Wi-fi router (SSID) you will connect toManually enter the SSID if not on the listSelect router’s security type (usually WAP2)

Check to confirm upload to Weather UndergroundEnter new Station ID and Station key assigned by Wunderground (Weather Underground)

Check to confirm upload to Weathercloud

Select time server


SETUP page







Solid: the display console isconnected to your wireless router

Flashing: the display console is attempting to connect to your wireless router

Flashing: the display console is currently in AP (access point) mode


NOTE: - When WI-FI setup is complete, your PC or mobile will resume your default WI-FI connection. - During AP mode, you can press and hold the [ WI-FI / SENSOR ] key for 6 seconds to stop AP mode and the console will restore your previous setting.

WI-FI CONNECTION STATUSBelow is the WI-FI icon status on the console LCD:

Flashing: Console is trying to connect to WI-FI router

TIME SERVER CONNECTION STATUSAfter the console has connected to the internet, it will attempt to connect to the internet time server to obtain the UTC time. Once the connection succeeds and the console's time has been updated, the “ ” icon will appear on the LCD.

Time zone: To display the time of your time-zone, change the time zone in CLOCK setting mode from '00' (default) to your time zone (e.g.08 for Hong Kong).1. Press and hold [ CLOCK SET ] key for 2s to enter time setting mode.2. Press [ ] or [ ] key to enter your time zone, then press and hold [ CLOCK SET ] key

setting for the console.

18

CALIBRATION

1. You may enter or change the off set and gain values for diff erent measurement parameters, while viewing the current off set and gain values next to the corresponding boxes. 2. Once you have completed your calibrations, press the APPLY button on the SETUP tab. 3. The current off set value will update to show the value that you entered (instead of the default value). If you want to change the value, you can enter a new value in the box beside the number (as in step 1). To update the value, again, press APPLY in the SETUP tab.NOTE:We do not recommend calibration of most values with the exception of Relative Pressure, which must be correctly calibrated to refl ect your distance above sea level to account for altitude eff ects.

11

The time will automatically synchronize Internet time server at 12:00AM and 12:00PM per day. Also you can press the [REFRESH ] key to get the internet time manually within 1 minute.

ADVANCE SETTING IN WEB INTERFACEPress "ADVANCED" key at the top of web interface to enter the advance setting page, this page allow you to set and view the calibration data of the console, also you can update the

-800 ~ 800hpa / -23.62 ~ 23.62inHg / -601.5 ~ 601.5mmHgSetting Range:

SETUP ADVANCED

Language: English

Temperature oC

Outdoor

Indoor

CH 1

CH 2

CH 3

CH 4

CH 5

CH 6

CH 7

Humidity %

Relative Pressure Offset:

Absolute Pressure Offset:

hpa

Range: -20 ~ 20(Default: 0)

Current offset: 10Current offset: -9

Current offset: -5Current offset: 2


Current offset: -2Current offset: 1.2

Current offset: -5Current offset: -0.2

Current offset: -3Current offset: -20.1

Current offset: -10Current offset: 11.5

Current offset: -3

Current offset: -3(Default: 0)

Current offset: 10(Default: 0)

Current offset: 0.2


Pressure

Range: -20.0 ~ 20.0oC-36.0 ~ 36.0oF (Default: 0.0)

**UV gain: Range: 0.01 ~ 10(Default: 1.00)Current gain: 1.1

** Depends on outdoor sensor type

Wind speed gain:

**Wind direction:

Rain gain: Range: 0.5 ~ 1.5(Default: 1.00)

Range: -10 ~ 10(Default: 0o)

Range: 0.5 ~ 1.5(Default: 1.00)

Current gain: 0.85

Current offset: 2o

Current gain: 0.75


Temperature calibration section

Pressure calibration section

Rain calibration section

Wind calibration section

Select setting unit

Advanced pageCALIBRATION1. User may enter or change the offset and gain values for different measurement parameters

while current offset and gain values are shown next to their corresponding boxes.2. Once completed, press Apply in the SETUP pageThe current offset value will show the previous value that you entered, if you want to change, just input the new value in the blank, the new value will valid once you press Apply icon in SETUP page.

NOTE:Calibration of most parameter is not required, with the exception of Relative Pressure, which must be calibrated to sea-level to account for altitude effects.

VIEW YOUR WEATHER DATA IN WUNDERGROUNDTo view your weather station live data in a web browser (PC or mobile version), please visit http://www.wunderground.com, and then enter your “Station ID” in the searching box. Your weather data will show up on the next page. You can also login your account to view and download the recorded data of your weather station.

Press ‘ADVANCED’ icon to view the advanced settings page

Humidity calibration section

Select setting unit

19

UPDATING THE FIRMWAREThis display console supports OTA (over the air) Function Firmware and WI-FI System Firmware updates via any web browser (not mobile browser) on a PC that is connected to WI-FI. The update function for both types of updates can be found at the bottom of the Advanced Tab on the wireless settings interface (see Advanced Settings via Web Interface on page 20.

Follow the steps below to update your device’s Function or WI-FI System Firmware

1. Download the latest version of the fi rmware (function or WI-FI) and save it to your PC. Remember where you saved the fi le. 2. Press and hold the SENSOR/WI-FI button for six (6) seconds to put the display console into AP mode, then connect the PC to the console (refer to steps in Set Up WI-FI Connection on page 18. 3. Click the button that says Browse next to the appropriate type of update that you downloaded and navigate to the location where you saved the fi le. 4. Click the corresponding Upload button to transfer the update fi le to the console.

5. The fi le will install automatically once it is uploaded. You can view update progress on the display console in the wind direction section (the number displayed will correspond to the percentage completed, so 50 = 50% and so on).

12

You can also use the Apple ipad's "WunderStation" app to login your own weather station to view the live data.

WunderStation

VIEWING YOUR WEATHER DATA IN WEATHERCLOUD1 . To view your weather station live data in a web browser (PC or mobile version), please visit

https://weathercloud.net and sign in your own account.

2 . Click the icon inside the pull down menu of your station.

3 . Click "Current", "Wind", "Evolution" or "Inside" icon to view the live data of your weather station .

FIRMWARE UPDATEThe console supports OTA firmware update capability. Its firmware may be updated over the air anytime (whenever necessary) through any web-browser on a PC with WI-FI connectivity. Update function, however, is not available through mobile/smart devices.Two types of firmware updates are available, namely Function Firmware and System WI-FI Firmware, and are located at the bottom of ADVANCED page.

Current Function firmware version

Current WI-FI firmware version

Current Functionfi rmware version

Current WI-FIfi rmware version

13

FIRMWARE UPDATE STEP1 . Download the latest version firmware (function or WI-FI) to your PC.2 . Set the Console into AP (access point) mode then connect the PC to the console (ref to

"SETUP WI-FI CONNECTION" section in previous page).3 . To update the Function firmware, click the Browse in Function firmware section and

browse to the location of the file you download in step 1. To update the WI-FI firmware, click the Browse in WI-FI firmware section.

4 . Click the corresponding Upload to start transfer the firmware file to console (indicated by a transfer completion %). Upload30% ...

BrowseC:\download\PWS_SYS.bin

Upload

Browse

Function firmware version: 1.00

WiFi firmware version: 1.00

3

44

3

5 . Once the console received the firmware file, it executes the update automatically as indicated by the update progress on display (i.e. 100 is completion).

6 . The console will restart once the update completed.NOTE: - Function and WI-FI firmware cannot be updated at the same time, you need to update one by one .

- Please keep connecting the power during the firmware update process. - Please make sure your PC's WI-FI connection is stable. - When the update process start, do not operate the PC and console. - During firmware update the console will stop upload data. It will reconnect to your WI-FI router and upload the data again once the update success. If the console cannot connect to your router, please end the SETUP page to setup again.

- After the firmware updates, user might need to input the Weather Underground ID and password again.

OTHER SETTING & FUNCTIONS OF THE CONSOLECLOCK SETTINGThis console is designed to obtain the local time by synchronize with the assigned internet time server. If you want to use it offline, you can set the time and date manually. During the first time startup, press and hold the [ WI-FI / SENSOR ] key for 6 seconds and let the console back to normal mode.1 . In normal mode, press and hold [ CLOCK SET ] key for 2 seconds to enter setting.2 . The setting sequence: Time Zone → DST ON/OFF → Hour → Minute → 12/24 hour format →

Year → Month → Day → M-D/D-M format → Time sync ON/OFF → weekday Language.3 . Press [ ] or [ ] key to change the value. Press and hold the key for quick-adjust.4 . Press [ CLOCK SET ] key to save and exit the setting mode, or the unit will automatically

exit the setting mode 60 seconds later without pressing any key.

NOTE: - In normal mode, press [ CLOCK SET ] key to switch between year and date display. - During the setting, you can press and hold [ CLOCK SET ] key for 2 seconds to back to normal model.

13

FIRMWARE UPDATE STEP1 . Download the latest version firmware (function or WI-FI) to your PC.2 . Set the Console into AP (access point) mode then connect the PC to the console (ref to

"SETUP WI-FI CONNECTION" section in previous page).3 . To update the Function firmware, click the Browse in Function firmware section and

browse to the location of the file you download in step 1. To update the WI-FI firmware, click the Browse in WI-FI firmware section.

4 . Click the corresponding Upload to start transfer the firmware file to console (indicated by a transfer completion %). Upload30% ...

BrowseC:\download\PWS_SYS.bin

Upload

Browse

Function firmware version: 1.00

WiFi firmware version: 1.00

3

4

5 . Once the console received the firmware file, it executes the update automatically as indicated by the update progress on display (i.e. 100 is completion).

6 . The console will restart once the update completed.NOTE: - Function and WI-FI firmware cannot be updated at the same time, you need to update one by one .

- Please keep connecting the power during the firmware update process. - Please make sure your PC's WI-FI connection is stable. - When the update process start, do not operate the PC and console. - During firmware update the console will stop upload data. It will reconnect to your WI-FI router and upload the data again once the update success. If the console cannot connect to your router, please end the SETUP page to setup again.

- After the firmware updates, user might need to input the Weather Underground ID and password again.

OTHER SETTING & FUNCTIONS OF THE CONSOLECLOCK SETTINGThis console is designed to obtain the local time by synchronize with the assigned internet time server. If you want to use it offline, you can set the time and date manually. During the first time startup, press and hold the [ WI-FI / SENSOR ] key for 6 seconds and let the console back to normal mode.1 . In normal mode, press and hold [ CLOCK SET ] key for 2 seconds to enter setting.2 . The setting sequence: Time Zone → DST ON/OFF → Hour → Minute → 12/24 hour format →

Year → Month → Day → M-D/D-M format → Time sync ON/OFF → weekday Language.3 . Press [ ] or [ ] key to change the value. Press and hold the key for quick-adjust.4 . Press [ CLOCK SET ] key to save and exit the setting mode, or the unit will automatically

exit the setting mode 60 seconds later without pressing any key.

NOTE: - In normal mode, press [ CLOCK SET ] key to switch between year and date display. - During the setting, you can press and hold [ CLOCK SET ] key for 2 seconds to back to normal model.

20

6. The console will restart once the update completes.

NOTES: • You cannot update the Function Firmware and WI-FI Firmware at the same time. Updates must be installed one by one.• Make sure the power cable remains connected during the update process.• Make sure your PC’s wireless connection is stable.• Once the update process starts, do not try to do anything else on your PC or on the display console.• During the firmware update process, the console will stop uploading data temporarily. It will reconnect to your router and resume uploading data once the update is complete. If the console cannot connect to your router, you may need to set up the WI-FI connection again, following the steps on page 18.• Once your firmware update completes, you may need to input your Weather Underground ID and password again on the SETUP tab of the wireless interface.

CREATE WEATHER UNDERGROUND ACCOUNT

1. Visit the Weather Underground website at https://www.wunderground.com and click the link that says “JOIN”. Follow the instructions to create an account. NOTE: Please use a valid email address to register your account.

2. Once you have created your account and completed the email validation process, return to the Weather Underground website. Click the dropdown link at the top of the site that says MORE, and then select Add Weather Station from the dropdown menu.

3. Follow the instructions on screen to enter your weather station information. Step 2 will ask you to enter a name for your weather station (get creative if you want, but don’t forget the name you gave it!) and choose your station hardware (choose “other”). Once you complete this section, click Submit to generate your unique Station ID and key.

Your display console can upload weather data to Weather Underground and/or Weathercloud via your WI-FI router.NOTE: Logia™ does not own Weather Underground or Weathercloud, and these instructions are liable to change without notice due to changes in either website.

CREATE WEATHER SERVER ACCOUNT

NOTE: Use the valid email address to register your account.

2. After you have created your account and completed the Email validation, please go back to the WUndergound web page. Click the " " on the top to open the drop-down menu and click “Add Weather Station”.


2. After you have created your account and completed the Email validation, please go back to the WUndergound web page. Click the " " on the top to open the drop-down menu and click “Add Weather Station”.

21

4. Write down or screenshot your Station ID and Station Key/Password for reference and to complete the setup process.

22

CREATE WEATHERCLOUD ACCOUNT

1. Visit the Weathercloud website at https://www.weathercloud.net and enter your information in the box that says Join Us Today. Follow the instructions to create an account. NOTE: Please use a valid email address to register your account.

2. Once your account is created, sign into it, and then click +New to add a new device.

3. Enter all the requested information into the Create New Device page. When presented with the Model selection box, choose LOWSC510WB Series under the Logia section. When presented with the Link Type selection box, choose Pro Weather Link. Once you have completed this section, click Create.

8

CREATE WEATHERCLOUD ACCOUNT1 . In https://weathercloud.net enter your information in "Join us today" section, then follow

the instructions to create your account .


2 . Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new device.

3 . Enter all the information in Create new device page, for the Model* selection box select the "W100 Series" under "CCL" section. for the Link type* selection box select the "Pro Weather Link", Once you have completed, click Create .

8






8






23

VIEW YOUR WEATHER DATA IN WEATHER UNDERGROUND

ACCESSING WEATHER DATA ONLINE

VIEW YOUR WEATHER DATA IN WEATHERCLOUD

To view your weather station data live via PC or mobile web browser, visit http://www.wunderground.com, and then enter the Station ID you were provided during account setup in the search box. Your weather data will show up on the next page. Alternately, you can log in to your Weather Underground account to view and download the recorded data from your weather station.

1. To view your weather station data live via PC or mobile web browser, visit http://www. weathercloud.net and sign into the account you created.2. Click on the tab at the top of the page titled Devices.3. Click on the Settings menu at the top right of the page, and select the option View.

You can also check Weather Underground web site to learn more about their mobile App for Android and iOS.

4. Write down or screenshot your Weathercloud ID and Station Key/Password for reference and to complete the setup process.

9






PWS-XXXXXX

PWS-XXXXXX




24

OTHER CONSOLE SETTINGS AND FUNCTIONSMANUALLY SETTING THE TIME

The display console is designed to synchronize with the internet time server to obtain the local time, but if you want to use it without connecting to your home wireless network, you can set the time manually. During initial setup, you will need to press and hold the SENSOR/WI-FI button for six (6) seconds, then let the display console return to normal mode. This will put it into offl ine mode for you to use it. 1. In normal operating mode while offl ine, press and hold the CLOCK SET button for two (2) seconds to enter the clock setting menu. 2. Press the or buttons to adjust the time zone. 3. Press the CLOCK SET button again to make adjustments to the next setting. 4. Settings will cycle through the following options: Time Zone > DST ON/OFF > Hour > Minute > 12/24-hour Format > Year > Month > Day > M-D/D-M Format > Time Sync ON/OFF > Language. 5. Press the CLOCK SET button one fi nal time after adjusting all settings options to save and exit, or the console will automatically save and exit the menu after 60 seconds of idle time.NOTES: • In normal operating mode, press the CLOCK SET button once to switch between date and year display.• While adjusting settings, you can press and hold the CLOCK SET button for two (2) seconds to return to normal mode.

MOON PHASE

The display console calculates the moon phase according to your time, date, and time zone. The table below explains the corresponding phases and their icons for both Northern and Southern hemispheres. Please refer to the section regarding Orienting the Wireless Weather Sensor Due South on page 25 for more information on setting up your Wireless Weather Sensor in the Southern Hemisphere.

4. Click on either Current, Wind, Evolution, or Inside to view your weather station’s data.

12

You can also use the Apple ipad's "WunderStation" app to login your own weather station to view the live data.

WunderStation

VIEWING YOUR WEATHER DATA IN WEATHERCLOUD1 . To view your weather station live data in a web browser (PC or mobile version), please visit

https://weathercloud.net and sign in your own account.

2 . Click the icon inside the pull down menu of your station.

3 . Click "Current", "Wind", "Evolution" or "Inside" icon to view the live data of your weather station .

FIRMWARE UPDATEThe console supports OTA firmware update capability. Its firmware may be updated over the air anytime (whenever necessary) through any web-browser on a PC with WI-FI connectivity. Update function, however, is not available through mobile/smart devices.Two types of firmware updates are available, namely Function Firmware and System WI-FI Firmware, and are located at the bottom of ADVANCED page.

Current Function firmware version

Current WI-FI firmware version

25

Northern Hemisphere Icons Southern Hemisphere IconsMoon Phase

New Moon

Waxing Crescent Moon

First Quarter Moon

Waxing Gibbous Moon

Full Moon

Waning Gibbous Moon

Third Quarter Moon

Waning Crescent Moon

NOTE: - In alarm mode, the “ ” icon will display on the LCD.

Alarm off Alarm on Alarm with ice-alert

Temp/Humidity TrendArrow Icon

Rising Steady Falling

Too cold Comfortable Too hot

No signal Weak signal Good signal

POINTING THE WIRELESS WEATHER SENSOR TO SOUTH

The outdoor wireless weather sensor is calibrated to be pointed North for maximum accuracy. However, for your convenience, if you are a user located in the Southern Hemisphere, you can use the sensor with the wind vane pointing South. 1. Mount and install the wireless weather sensor with the wind meter end pointed South, instead of North. (Please refer to the Installation Instructions on page 12 for mounting instructions.)2. While the display console is in normal operating mode, press and hold the INDEX button for eight (8) seconds until the N icon appears in the weekday section of the display to indicate the console is in sensor orientation mode.3. Use the or buttons to change the orientation to Southern Hemisphere. The N should change to an S.4. Press the INDEX button another time to confirm and exit the menu.

NOTES:• Changing the hemisphere setting will automatically switch the direction of the moon phases on the display.• Pointing the wireless weather sensor toward the South will allow maximum sunlight on the solar panel, especially during the winter season in the Southern Hemisphere.

26

SETTING THE ALARM

ACTIVATING/DEACTIVATING THE ALARM & TEMPERATURE PRE-ALARM

The temperature pre-alarm will alert you 30 minutes prior to your alarm time whenever the outdoor temperature falls below 26.5°F (-3°C). 1. In normal operating mode, press the ALARM button to display the set alarm time for five (5) seconds.2. When the alarm time is being shown on the LCD display, press the ALARM button again to cycle through the alarm functions as shown below. The corresponding icons will appear on the LCD display.

If you’d like to use your display console as an alarm clock, follow these instructions to set the alarm time:1. In normal operating mode, press and hold the ALARM button for two (2) seconds until the alarm hour starts flashing. This indicates that you have entered the alarm time setting mode. 2. Use the or buttons to adjust the alarm hour. Press and hold either button to move through the hours quickly.3. Press the ALARM button again to confirm the alarm hour and move to adjusting the minutes. The minute digits should be flashing.4. Use the or buttons to adjust the alarm minute. Press and hold either button to move through the minutes quickly.5. Press the ALARM button to save and exit the menu.

NOTES: • Once you have an alarm set, the icon will be displayed next to the time on the LCD display. • The alarm function will be activated automatically once you set a time.

3. When the clock reaches the designated alarm time, the alarm sound will start playing.4. To stop the alarm: a. Allow the alarm to continue for two minutes and it will stop itself automatically. It will remain set for the following day. b. Press the SNOOZE/BACKLIGHT button on top of the unit to snooze the alarm for five minutes. The snooze can be set continuously for 24 hours. We don’t recommend doing that, though. While the console is in snooze mode, the alarm icon will continue flashing. c. Press and hold the SNOOZE/BACKLIGHT BELL for two (2) seconds to stop the alarm completely. It will stay set for the following day. d. Press the ALARM button to stop the alarm completely. It will remain set for the following day.


New Moon


First Quarter Moon

Waxing Gibbous Moon

Full Moon

Waning Gibbous Moon

Third Quarter Moon








27

TEMPERATURE/HUMIDITY & TRENDS

VIEWING OUTDOOR CHANNELS

RECEIVING WIRELESS SENSOR SIGNALS

Press the °C/°F button to switch between Celsius and Fahrenheit temperature measurements. The arrows show the trend in changes to the temperature/humidity levels.

This console is capable of pairing with the wireless weather sensor and up to 7 additional wireless thermal-hygro sensors. If you have 2 or more sensors installed, press the CH button to cycle between different wireless channels in normal operating mode, or press and hold the CH button for two (2) seconds to toggle auto-cycle mode on, which cycles through displaying all connected channels at 4-second intervals. While the console is in auto-cycle mode, you can press the CH button once to toggle auto-cycle mode off and continue displaying the current channel.

1. While in normal operating mode, press the SENSOR/SYNC button once to start receiving the current sensor signal on the channel being displayed. (i.e. if you’re on CH 1 and press the SENSOR/ SYNC button, the current wireless sensor signal being received will only display on CH 1.) The signal icon will start flashing.2. The signal icon will continue flashing until it successfully receives a signal. If no signal is received within five (5) minutes, the icon will disappear.

NOTE: • If/when the temperature outside falls below -40°F (-40°C), the LCD display will show the word “Lo” in the temperature section. If the temperature outside rises above 176°F (80°C), the LCD display will show the word, “HI” in the temperature section. • If/when the humidity level falls below 1%, the LCD display will show the word “Lo” in the humidity section. If/when the humidity level rises above 99%, the LCD display will show the word, “HI” in the humidity section.


New Moon


First Quarter Moon

Waxing Gibbous Moon

Full Moon

Waning Gibbous Moon

Third Quarter Moon







No signal Weak signal Good signalNorthern Hemisphere Icons Southern Hemisphere IconsMoon Phase

New Moon


First Quarter Moon

Waxing Gibbous Moon

Full Moon

Waning Gibbous Moon

Third Quarter Moon








28

3. If the signal for the outdoor channel has been interrupted and does not recover within 15 minutes, the signal icon will disappear. The temperature and humidity section (outdoor) will display “—” on the corresponding channel. 4. If the signal still does not recover within 48 hours, the “—” display will become permanent. You will need to replace the batteries on the associated channel’s sensor and press the SENSOR/SYNC button to pair up the sensors again.5. After replacing batteries in the display console or the wireless weather sensor, or if the unit fails to receive a specified channel, press the SENSOR/SYNC button while the failed channel is being displayed to manually receive that sensor’s signal again.

1. While in normal operating mode, press and hold the WIND button for two seconds to enter the wind speed unit setting mode. The unit display will start flashing. Press the or buttons to cycle through the wind speed units in the following order: m/s > km/h > knots > mph

INDOOR COMFORT INDICATOR KEY

SELECTING WIND DISPLAY MODE

WIND READOUTS Real time winddirection indicator

Past wind directions indicator of last 5 minutes

Average / gustwind speed

Wind Direction

Set Wind Speed Units

The indoor comfort indicators display a pictorial representation based on the indoor air temperature and humidity levels to determine the approximate comfort level.

While in normal operating mode, press the WIND button to switch between the average wind speed measurement and gust wind speed measurement.

NOTE:Comfort indicator levels may vary even when the temperature is the same due to variances in relative humidity levels. No comfort indicator will be displayed if the temperature falls below 32°F (0°C) or over 140°F (60°C).


New Moon


First Quarter Moon

Waxing Gibbous Moon

Full Moon

Waning Gibbous Moon

Third Quarter Moon








16

WIRELESS SENSOR SIGNAL RECEIVING1 . The console display signal strength for the wireless 5-IN-1 sensor, as per table below:

No signal Weak signal Good signal2 . If the signal has discontinued and does not recover within 15 minutes, the signal icon will

disappear. The temperature and humidity will display “Er” for the corresponding channel. 3 . If the signal does not recover within 48 hours, the “Er” display will become permanent. You

need to replace the batteries and then press [ SENSOR / WI-FI] key to pair up the sensor again .

VIEW THE OUTDOOR CHANNEL (OPTIONAL FEATURE WITH ADD ON EXTRA THERMAL HYGRO SENSORS)This console is capable to pair with a wireless 5-IN-1 sensor and up to 7 wireless thermal-hygro sensors. If you have 2 or more sensors, you can press [ CHANNEL ] key to switch between different wireless channels in normal mode, or press and hold [ CHANNEL ] key for 2 seconds to toggle auto-cycle mode to display the connected channels at 4 seconds interval.During auto-cycle mode, press [ CHANNEL ] key to stop auto cycle and display the current channel .

WINDWIND SPEED AND DIRECTION SECTION OVERVIEW

Past wind directions indicator of last 5 minutes

Real time wind direction indicator

Average / gust wind speed

TO SET THE WIND SPEED UNIT AND DIRECTION DISPLAY FORMAT1 . In normal mode, press and hold [ WIND ] key for 2 seconds to enter into wind speed unit

mode and the unit will flash. Press [ ] or [ ] key to change the wind speed unit in this sequence: m/s → km/h → knots → mph

2 . Press [ WIND ] key again to return to normal mode.

TO SELECT THE WIND DISPLAY MODEIn normal mode, press [ WIND ] key to switch between AVERAGE and GUST wind speed.

WEATHER INDEXAt the WEATHER INDEX section, you can press [ INDEX ] key to view the weather index in this sequence: FEELS LIKE → HEAT INDEX → WIND CHILL → DEWPOINT.

FEELS LIKEThe feels like temperature index determine how the outdoor temperature that people actually feel .

29

2. Press the WIND button again to return to normal display mode.

3. Press the WIND button while in normal operating mode to switch between AVERAGE and GUST wind speeds.

WEATHER INDEXES

Wind Speed Level Chart

Feels Like

Wind Chill

When reading the Weather Index display, you can press the INDEX button to cycle through different weather indexes in the following order: Feels Like > Heat Index > Wind Chill > Dewpoint.

The Feels Like temperature index determines what temperature it actually feels like outside, taking into account factors like wind chill and the heat index.

Wind chill is determined by a combination of the wireless weather sensor’s temperature and wind speed data.

the signal icon will disappear. The temperature and humidity will display “--” for the corresponding channel.

4. If the signal does not recover within 48 hours, the “--” display will become permanent you need to replace the batteries of “--” channel’s sensor(s) and then press [ SENSOR / SYNC] key to pair up the sensors of each “--” channels again.

NOTE: After replacing the batteries of the wireless sensor or the unit fails to receive sensor signal of

[ SENSOR / SYNC ] key to manually receive that sensor signal again.

COMFORT INDICATIONThe comfort indication is a pictorial indication based on indoor air temperature and humidity in an attempt to determine comfort level.


NOTE:Comfort indication can vary under the same temperature, depending on the humidity.There is no comfort indication when temperature is below 0°C (32°F) or over 60°C (140°F).

WIND

Indicator of winddirection over thelast five minutes

16 direction or relative degree reading

Real-time wind direction indicator

Wind speed level

Average / gust wind speed

To select the wind display modeIn normal mode, press [ WIND ] key to switch between AVERAGE and GUST wind speed.

To set the wind speed unit and direction display format1. In normal mode, press and hold [ WIND ] key for 2 seconds to enter into wind speed unit

[ GRAPH / ] or [ HISTORY / V ] key to change the wind speed unit in this sequence: m/s → km/h → knots → mph

2. Press [ WIND ] key again to enter into wind direction display format setting mode. The wind [ GRAPH / ] or [ HISTORY / V ] key to select

the display format 16 direction or relative degree reading.3. Press [ WIND ] key again to return to normal mode.

Wind Speed Level

SpeedLevel

0.1~11.8 mphLight

12~30.4 mphModerate

31~54.7 mphStrong

>55 mphStorm

Heat Index

Dew Point

The heat index is determined by the wireless weather sensor’s temperature and humidity readings when the temperature outdoors is between 80°F (27°C) and 120°F (50°C).

• The dew point is the temperature below which the water vapor in air at constant barometric pressure condenses into liquid water at the same rate at which it evaporates. The condensed water is called dew when it forms on a solid surface.• The dew point temperature is determined by the temperature and humidity data from the wireless weather sensor.

Beaufort Scale Level Description Wind Speed Land Condition

0 Calm Calm. Smoke rises vertically

1 Light air

2 Light breeze

3 Gentle breeze

4 Moderate breeze

5 Fresh breeze

6 Strong breeze

7 High wind

< 1 km/h< 1 mph< 1 knot

.< 0 3 m/s.1 1 ~ 5km/h1 ~ 3 mph1 ~ 3 knot. .0 3 ~ 1 5 m/s6 ~ 11 km/h4 ~ 7 mph4 ~ 6 knot. .1 6 ~ 3 3 m/s

12 ~ 19 km/h8 ~ 12 mph7 ~ 10 knot. .3 4 ~ 5 4 m/s

20 ~ 28 km/h13 ~ 17 mph11 ~ 16 knot. .5 5 ~ 7 9 m/s

29 ~ 38 km/h18 ~ 24 mph17 ~ 21 knot. .8 0 ~ 10 7 m/s

39 ~ 49 km/h25 ~ 30 mph22 ~ 27 knot. .10 8 ~ 13 8 m/s

50 ~ 61 km/h31 ~ 38 mph28 ~ 33 knot. .13 9 ~ 17 1 m/s

Smoke drifts indicate wind direction. Leaves and wind

vanes are stationary.

Wind can be felt on exposed skin. Leaves rustle. Wind

vanes begin to move.

Leaves and small twigs constantly moving, light

flags extended.

Dust and loose paper raised. Small branches

begin to move.

Branches of a moderate size move. Small trees in

leaf begin to sway.

Whole trees in motion. Effort needed to walk

against the wind.

Some twigs broken from trees. Cars veer on the

road. Progress on foot is seriously impeded.

Some branches break off trees, and some small trees blow

over. Construction/temporary signs and barricades blow over.

Trees are broken off or uprooted, structural

damage likely.

Widespread vegetation and structural damage likely.

Severe widespread damage to vegetation and structures.

Debris and unsecured objects are hurled about.

Large branches in motion. Whistling heard in overhead wires.

Umbrella use becomes difficult. Empty plastic bins tip over.

8 Gale

9 Strong gale

10 Storm

11 Violent storm

12 Hurricane force

62 ~ 74 km/h39 ~ 46 mph34 ~ 40 knot

17. 2 ~ 20.7 m/s75 ~ 88 km/h47 ~ 54 mph41 ~ 47 knot

20.8 ~ 24.4 m/s89 ~ 102 km/h55 ~ 63 mph48 ~ 55 knot

24.5 ~ 28.4 m/s103 ~ 117 km/h

64 ~ 73 mph56 ~ 63 knot

28.5 ~ 32.6 m/s≥ 118 km/h≥ 74 mph≥ 64 knot≥ 32.7m/s

Heat Index range Warning Explanation80°F to 90°F (27°C to 32°C) Caution Possibility of heat exhaustion91°F to 105°F (33°C to 40°C) Extreme Caution Possibility of heat dehydration106°F to 129°F (41°C to 54°C) Danger Heat exhaustion likely≥ 130°F (≥ 55°C) Extreme Danger Strong risk of dehydration / sun stroke

Sunny Partly cloudy Cloudy Rainy Rainy / Stormy Snowy

Absolute The absolute atmospheric pressure of your locationRelative The relative atmospheric pressure based on the sea level

30

NOTE:• The accuracy of a general pressure-based forecast is about 70% - 75%. Forecasts are not guaranteed.• The forecast section reflects a general prediction for the next roughly 12 ~ 24 hours. It may not necessarily reflect the current situation.• The SNOWY weather forecast is not based on the atmospheric pressure, but based on the current temperature reading from that wireless sensor. When the outdoor temperature is below ~ 26°F (-3°C), the SNOWY weather indicator will be shown on the LCD display.

The built-in barometer can notice atmospheric pressure changes, and based on the data collected, can predict the weather conditions in the forthcoming 12-24 hours within a 19 ~ 31 mile (30 ~ 50 km) radius.

WEATHER FORECAST



1 Light air

2 Light breeze

3 Gentle breeze

4 Moderate breeze

5 Fresh breeze

6 Strong breeze

7 High wind



12 ~ 19 km/h8 ~ 12 mph7 ~ 10 knot. .3 4 ~ 5 4 m/s

20 ~ 28 km/h13 ~ 17 mph11 ~ 16 knot. .5 5 ~ 7 9 m/s

29 ~ 38 km/h18 ~ 24 mph17 ~ 21 knot. .8 0 ~ 10 7 m/s

39 ~ 49 km/h25 ~ 30 mph22 ~ 27 knot. .10 8 ~ 13 8 m/s

50 ~ 61 km/h31 ~ 38 mph28 ~ 33 knot. .13 9 ~ 17 1 m/s






flags extended.


begin to move.


leaf begin to sway.


against the wind.






damage likely.






8 Gale

9 Strong gale

10 Storm

11 Violent storm

12 Hurricane force

62 ~ 74 km/h39 ~ 46 mph34 ~ 40 knot

17. 2 ~ 20.7 m/s75 ~ 88 km/h47 ~ 54 mph41 ~ 47 knot

20.8 ~ 24.4 m/s89 ~ 102 km/h55 ~ 63 mph48 ~ 55 knot

24.5 ~ 28.4 m/s103 ~ 117 km/h

64 ~ 73 mph56 ~ 63 knot

28.5 ~ 32.6 m/s≥ 118 km/h≥ 74 mph≥ 64 knot≥ 32.7m/s




In normal mode, press BARO UNIT button on the back side to change the barometer unit in this sequence: hPa > inHg > mmHg.

In normal mode, press BARO button to switch between ABSOLUTE / RELATIVE barometric reading.

BAROMETRIC PRESSURE

TO SET THE BAROMETER UNIT

TO VIEW THE ABSOLUTE / RELATIVE BAROMETRIC READING

The atmospheric pressure is the pressure at any location on Earth caused by the weight of the column of air directly above that location. The average pressure gradually decreases as the altitude increases. Meteorologists use barometers to measure atmospheric pressure. Since variation in atmospheric pressure can be greatly affected by the weather, it is possible to forecast the weather by measuring these changes in pressure.



1 Light air

2 Light breeze

3 Gentle breeze

4 Moderate breeze

5 Fresh breeze

6 Strong breeze

7 High wind



12 ~ 19 km/h8 ~ 12 mph7 ~ 10 knot. .3 4 ~ 5 4 m/s

20 ~ 28 km/h13 ~ 17 mph11 ~ 16 knot. .5 5 ~ 7 9 m/s

29 ~ 38 km/h18 ~ 24 mph17 ~ 21 knot. .8 0 ~ 10 7 m/s

39 ~ 49 km/h25 ~ 30 mph22 ~ 27 knot. .10 8 ~ 13 8 m/s

50 ~ 61 km/h31 ~ 38 mph28 ~ 33 knot. .13 9 ~ 17 1 m/s






flags extended.


begin to move.


leaf begin to sway.


against the wind.






damage likely.






8 Gale

9 Strong gale

10 Storm

11 Violent storm

12 Hurricane force

62 ~ 74 km/h39 ~ 46 mph34 ~ 40 knot

17. 2 ~ 20.7 m/s75 ~ 88 km/h47 ~ 54 mph41 ~ 47 knot

20.8 ~ 24.4 m/s89 ~ 102 km/h55 ~ 63 mph48 ~ 55 knot

24.5 ~ 28.4 m/s103 ~ 117 km/h

64 ~ 73 mph56 ~ 63 knot

28.5 ~ 32.6 m/s≥ 118 km/h≥ 74 mph≥ 64 knot≥ 32.7m/s




17

HEAT INDEXThe heat index, which is determined by the wireless 5-IN-1 sensor's temperature & humidity data, when the temperature is between 27°C (80°F) and 50°C (120°F). Heat Index range Warning Explanation27°C to 32°C (80°F to 90°F) Caution Possibility of heat exhaustion33°C to 40°C (91°F to 105°F) Extreme Caution Possibility of heat dehydration41°C to 54°C (106°F to 129°F) Danger Heat exhaustion likely≥55°C (≥130°F) Extreme Danger Strong risk of dehydration / sun stroke

WIND CHILLA combination of the wireless 5-IN-1 sensor's temperature and wind speed data determines the current wind chill factor.

DEW POINT - The dew point is the temperature below which the water vapor in air at constant barometric pressure condenses into liquid water at the same rate at which it evaporates. The condensed water is called dew when it forms on a solid surface.

- The dew point temperature is determined by the temperature & humidity data from wireless 5-IN-1 sensor .

WEATHER FORECASTThe built-in barometer can notice atmosphere pressure changes. Based on the data collected, it can predict the weather conditions in the forthcoming 12~24 hours within a 30~50km (19~31 miles) radius.


NOTE: - The accuracy of a general pressure-based weather forecast is about 70% to 75%. - The weather forecast is reflecting the weather situation for next 12~24 hours, it may not necessarily reflect the current situation.

- The SNOWY weather forecast is not based on the atmospheric pressure, but based on the temperature of outdoor. When the temperature is below -3°C (26°F), the SNOWY weather icon will be displayed on the LCD.

BAROMETRIC PRESSUREThe atmospheric pressure is the pressure at any location of the earth caused by the weight of the column of air above it. One atmospheric pressure refers to the average pressure and gradually decreases as altitude increases. Meteorologists use barometers to measure atmospheric pressure. Since variation in atmospheric pressure greatly affected by weather, it is possible to forecast the weather by measuring the changes in pressure.

TO SET THE BAROMETER UNITIn normal mode, press [ BARO UNIT ] key to change the barometer unit in this sequence: hPa → inHg → mmHg

31

RAINFALL

The Rainfall shows information regarding the rainfall and rain rate.

1. Press and hold the RAIN button for two (2) seconds to enter unit setting mode.2. Press the or buttons to toggle the units of measure for rainfall between mm and in.3. Press the RAIN button again to save and exit the setting mode.

Set the Rainfall Units

Select the Rainfall Display Mode

Reset the Accumulating Rainfall Record

Press the RAIN button to toggle between:1. HOURLY: total rainfall in the past hour2. DAILY: total rainfall since midnight3. WEEKLY: total rainfall for the current week4. MONTHLY: total rainfall since the beginning of the current month5. RATE: current rainfall rate in the past hour (updates every 24 seconds)6. ACCUMULATION: total rainfall since the last reset (will show the record start date on the display for five seconds)

While in normal operating mode, press and hold the °C/°F button for two (2) seconds to reset the ACCUMULATION rainfall record.

NOTE:• To ensure precise data, please reset the ACCUMULATION rainfall record whenever you move and reinstall your wireless weather sensor to a different location.

MAX/MIN DATA RECORD

TO VIEW THE ACCUMULATED MAX / MIN

The display console can record the accumulated and daily MAX/MIN weather data with a corresponding time stamp for you to review.

In normal mode, press [ MAX / MIN ] key to check MAX/MIN records. The display sequence is:

18

TO VIEW THE ABSOLUTE / RELATIVE BAROMETRIC READINGIn normal mode, press [ BARO ] key to switch between ABSOLUTE / RELATIVE barometric reading.

RAINFALLThe RAINFALL section shows the rainfall and rain rate information

TO SET THE RAINFALL UNIT1 . Press and hold [ RAIN ] key for 2 seconds to enter unit setting mode.2 . Press [ Ʌ ] or [ V ] key to toggle the rainfall unit between mm and in.3 . Press [ RAIN ] key to confirm and exit the setting.

TO SELECT THE RAINFALL DISPLAY MODEPress [ RAIN ] key to toggle between:1. HOURLY - the total rainfall in the past hour 2. DAILY - the total rainfall from midnight3. WEEKLY - the total rainfall of the current week4. MONTHLY- the total rainfall of the current calendar month5. Total - the total rainfall since the last reset6. Rate - Current rainfall rate in past an hour (Update every 24 seconds)

TO RESET THE TOTAL RAINFALL RECORDIn normal mode, press and hold [ HISTORY ] key for 2 seconds to reset all the rainfall record.

NOTE:To ensure correct data, please reset all the rainfall record when you reinstall your wireless 5-IN-1 sensor to other location

MAX / MIN DATA RECORDThe console can record the accumulated MAX / MIN weather data with the corresponding time stamp for you to easy review.

TO VIEW THE ACCUMULATED MAX / MINIn normal mode, press [ MAX / MIN ] key to check MAX/MIN records. The display sequence is: indoor (or current channel) MAX temperature → indoor (or current channel) MIN temperature → indoor (or current channel) MAX humidity → indoor (or current channel) MIN humidity → outdoor MAX temperature → outdoor MIN temperature → outdoor MAX humidity → outdoor MIN humidity → MAX average wind speed → MAX gust → MAX relative pressure → MIN relative pressure → MAX absolute pressure → MIN absolute pressure → MAX FEELS LIKE → MIN FEELS LIKE→ MAX heat index → MIN heat index → MAX wind chill → MIN wind chill → MAX dew point → MIN dew point → MAX daily rainfall.

TO CLEAR THE MAX/MIN RECORDSPress and hold [ MAX / MIN ] key for 2 seconds to reset the MAX/MIN records of specify weather display section.

NOTE:The LCD will also display the " " icon, data records time & date.

32

Reset the Accumulated MAX/MIN Records

indoor (or current channel) MAX temperature > indoor (or current channel) MIN temperature > indoor (or current channel) MAX humidity > indoor (or current channel) MIN > humidity outdoor MAX temperature > outdoor MIN temperature > outdoor MAX humidity > outdoor MIN humidity > MAX average wind speed > MAX gust > MAX relative pressure > MIN relative pressure > MAX absolute pressure MIN absolute pressure > MAX FEELS LIKE > MIN FEELS LIKE > MAX heat index > MIN heat index > MAX wind chill > MIN wind chill > MAX dew point > MIN dew point > MAX daily rainfall.* or current display channel sensor

Press and hold the MAX/MIN button for two (2) seconds to reset the MAX/MIN records of the specific weather display section.

The display console automatically stores the weather data from the past 24 hours.1. Press the HISTORY button to check the beginning of the current hour’s weather data, e.g., if the current time is 7:25 AM on Dec 1st, the display will show the data for 7:00 AM on Dec 1st. 2. Press the HISTORY button to view the older readings for each hour of the past 24 hours, e.g. 6:00 AM (Dec 1st), 5:00 AM (Dec 1st), …, 10:00 AM (Nov 30th), 9:00 AM (Nov 30th), 8:00 AM (Nov 30th).

WEATHER ALERT SETTINGS

To Set the Alert

History Data for Past 24 Hours

The Weather Alert can alert you to certain weather conditions by activating an alarm sound and flashing the LCD display’s alert icon when specific criteria are met.

1. Press the ALERT button to cycle through and display the desired weather alert options in the following order:

NOTE: The LCD display will also show the History icon, along with the time and date, when displaying the history data records.

Alert Option Sequence Setting Range Display Section Default Setting

High Outdoor Humidity AlertLow Outdoor Humidity AlertHigh Indoor Temperature AlertLow Indoor Temperature AlertHigh Indoor Humidity AlertLow Indoor Humidity AlertWind Speed Alert

-40°F ~ 176°F(-40°C ~ 80°C)

0.1 m/s ~ 50 m/s(0.1 ~ 180 km/h0.1 ~ 112 mph0.1 ~ 97 knots)

17.2 m/s(62 km/h39 mph

34 knots)

1% ~ 99%

-40°F ~ 176°F(-40°C ~ 80°C)

1% ~ 99%

Outdoor temperature & humidity

Indoor temperature & humidity

Wind direction & speed

104°F (40°C)

32°F (0°C)

80%40%

104°F (40°C)32°F (0°C)

80%40%

Pressure Drop Alert 1hPa ~ 10hPa Barometer & Rainfall 3hPaHourly Rainfall Alert 0.04 in ~ 39 in

(1 mm ~ 1000 mm)-40°F ~ 140°F (-40°C ~ 60°C)

4 in (100 mm)

Low Wind Chill Alert Weather index 32°F (0°C)High Dew Point Alert 50°F (10°C)Low Dew Point Alert 14°F (-10°C)High Heat Index Alert 81°F ~ 120°F

(27°C ~ 49°C)95°F (35°C)

High Beaufort Scale Alert 1 ~12 6

High Outdoor Temperature Alert (current channel)Low Outdoor Temperature Alert (current channel)

33

Alert Option Sequence Setting Range Display Section Default Setting

High Outdoor Humidity AlertLow Outdoor Humidity AlertHigh Indoor Temperature AlertLow Indoor Temperature AlertHigh Indoor Humidity AlertLow Indoor Humidity AlertWind Speed Alert

-40°F ~ 176°F(-40°C ~ 80°C)

0.1 m/s ~ 50 m/s(0.1 ~ 180 km/h0.1 ~ 112 mph0.1 ~ 97 knots)

17.2 m/s(62 km/h39 mph

34 knots)

1% ~ 99%

-40°F ~ 176°F(-40°C ~ 80°C)

1% ~ 99%


Indoor temperature & humidity

Wind direction & speed

104°F (40°C)

32°F (0°C)

80%40%

104°F (40°C)32°F (0°C)

80%40%

Pressure Drop Alert 1hPa ~ 10hPa Barometer & Rainfall 3hPaHourly Rainfall Alert 0.04 in ~ 39 in

(1 mm ~ 1000 mm)-40°F ~ 140°F (-40°C ~ 60°C)

4 in (100 mm)

Low Wind Chill Alert Weather index 32°F (0°C)High Dew Point Alert 50°F (10°C)Low Dew Point Alert 14°F (-10°C)High Heat Index Alert 81°F ~ 120°F

(27°C ~ 49°C)95°F (35°C)

High Beaufort Scale Alert 1 ~12 6

High Outdoor Temperature Alert (current channel)Low Outdoor Temperature Alert (current channel)

2. While on the alert option you want to set, press and hold the ALERT button for two (2) seconds to enter that alert’s settings mode. The alert option will start flashing.3. Press the or buttons to adjust the value, or press and hold the buttons to adjust the value more quickly.4. Press the ALERT button when the desired value is reached to save the alert setting, then press the ALARM button to toggle the weather alert on or off.

5. Press any button on the front of the display console to save and return to normal mode, or wait 30 seconds without pressing any buttons and the alert will save itself and return to normal mode.

To Silence the Weather Alert Alarm

Press the SNOOZE/LIGHT button on top of the display console to silence the alarm, or it will automatically turn off after two (2) minutes.

NOTES:• Once the alert is triggered, the alarm will sound for two (2) minutes and the associated alert icon and weather readings will flash. • If the alert alarm automatically shuts off after two (2) minutes instead of being manually shut off, the associated alert icon and readings will continue flashing until the reading is out of the alert range.• The weather alert alarm will go off once the readings fall into alert range again.

19

PAST 24 HOURS HISTORY DATAThe console automatically stores the weather data of the past 24 hours.1 . Press [ HISTORY ] key to check the beginning of the current hour's weather data, e.g. the

current time is 7:25 am, March 8, the display will show the data of 7:00am, March 8.2 . Press [ HISTORY ] key repeatedly to view older readings of the past 24 hours, e.g. 6:00am

(Mar 8), 5:00am (Mar 8), …, 10:00am (Mar 7), 9:00am (Mar 7), 8:00am (Mar 7)

NOTE:The LCD will also display the " " icon, history data records with time & date.

WEATHER ALERT SETTINGWeather Alert can alert you of certain weather conditions. Once the alert criterion is met, the alarm sound will activate and the LCD’s alert icon will flash.

TO SET ALERT1 . Press [ ALERT ] to select and display the desired weather alert reading in the sequence

below:

Alert reading Sequence Setting Range Display Section Default ValueIndoor Temperature High Alert(current channel)

-40°C ~ 80°C

Indoor / CH temperature & humidity

40°C

Indoor Temperature Low Alert(current channel) 0°C

Indoor Humidity High Alert(current channel)

1% ~ 99%80%

Indoor Humidity Low Alert(current channel) 40%

Outdoor Temperature High Alert-40°C ~ 80°C


40°COutdoor Temperature Low Alert 0°COutdoor Humidity High Alert

1% ~ 99%80%

Outdoor Humidity Low Alert 40%Average Wind Speed 0.1m/s ~ 50m/s Wind direction & speed 17.2mm/hPressure Drop 1hPa ~ 10hPa Barometer 3hPaHourly Rainfall 1mm ~ 1000mm Rainfall 100mm

2 . Under the current alert reading, press and hold [ ALERT ] key for 2 seconds to enter alert setting and the alert reading will flash.

3 . Press [ Ʌ ] or [ V ] key to adjust the value or press and hold the key to change rapidly.4 . Press [ ALERT ] key to confirm the value.5 . Press [ ALARM ] key to toggle the regarding alert on / off.6 . Press [ ALERT ] key to step to next alert reading.

High /LowAlert on Alert off

Alert on Alert off7 . Press any key on the front side to save alert on /off status and back to normal mode, or it

will automatically back to normal mode after 30 seconds without pressing any key.

19

PAST 24 HOURS HISTORY DATAThe console automatically stores the weather data of the past 24 hours.1 . Press [ HISTORY ] key to check the beginning of the current hour's weather data, e.g. the

current time is 7:25 am, March 8, the display will show the data of 7:00am, March 8.2 . Press [ HISTORY ] key repeatedly to view older readings of the past 24 hours, e.g. 6:00am

(Mar 8), 5:00am (Mar 8), …, 10:00am (Mar 7), 9:00am (Mar 7), 8:00am (Mar 7)

NOTE:The LCD will also display the " " icon, history data records with time & date.

WEATHER ALERT SETTINGWeather Alert can alert you of certain weather conditions. Once the alert criterion is met, the alarm sound will activate and the LCD’s alert icon will flash.

TO SET ALERT1 . Press [ ALERT ] to select and display the desired weather alert reading in the sequence

below:

Alert reading Sequence Setting Range Display Section Default ValueIndoor Temperature High Alert(current channel)

-40°C ~ 80°C

Indoor / CH temperature & humidity

40°C

Indoor Temperature Low Alert(current channel) 0°C

Indoor Humidity High Alert(current channel)

1% ~ 99%80%

Indoor Humidity Low Alert(current channel) 40%

Outdoor Temperature High Alert-40°C ~ 80°C


40°COutdoor Temperature Low Alert 0°COutdoor Humidity High Alert

1% ~ 99%80%

Outdoor Humidity Low Alert 40%Average Wind Speed 0.1m/s ~ 50m/s Wind direction & speed 17.2mm/hPressure Drop 1hPa ~ 10hPa Barometer 3hPaHourly Rainfall 1mm ~ 1000mm Rainfall 100mm

2 . Under the current alert reading, press and hold [ ALERT ] key for 2 seconds to enter alert setting and the alert reading will flash.

3 . Press [ Ʌ ] or [ V ] key to adjust the value or press and hold the key to change rapidly.4 . Press [ ALERT ] key to confirm the value.5 . Press [ ALARM ] key to toggle the regarding alert on / off.6 . Press [ ALERT ] key to step to next alert reading.

High /LowAlert on Alert off

Alert on Alert off7 . Press any key on the front side to save alert on /off status and back to normal mode, or it

will automatically back to normal mode after 30 seconds without pressing any key.

High / Low Alert on Alert off

34

CLEANING THE RAIN COLLECTOR

1. Rotate the rain collector by 30° counter-clockwise until it is in the unlock position as shown.

20

MAINTENANCE

BATTERY REPLACEMENTIf the low battery indicator “ ” displayed in time section, it indicates that the console battery power is low . You should replace all the batteries in the console at onceIf the low battery indicator “ ” displayed in outdoor section, it indicates that the current channel wireless outdoor sensor battery power is low . You should replace all the batteries in the current channel sensor at once .

Low battery indicator for main unit Low battery indicator for wireless sensor

CLEANING THE RAIN COLLECTOR

1 . Rotate the rain collector by 30° anticlockwise .2 . Gently remove the rain collector .3 . Clean and remove any debris or insects .4 . Install all the parts when they are fully clean

and dried .

N N

“Unlock” Position“Lock” Position

N

TO CLEAN THE THERMO/HYGRO SENSOR1 . Unscrew the 2 screws at the bottom of the radiation shield .2 . Gently pull out the shield .3 . Remove carefully any dirt or insects inside the sensor casing (Do not let the sensors inside get

wet) .4 . Clean the shield with water and remove any dirt or insects .5 . Install all the parts back when they are fully clean and dried .

PRECAUTIONS - Keep and reading the “User manual” is highly recommended . The manufacturer and supplier cannot accept any responsibility for any incorrect readings, export data lost and any consequences that occur should an inaccurate reading take place .

- Do not subject the unit to excessive force, shock, dust, temperature or humidity . - Do not cover the ventilation holes with any items such as newspapers, curtains etc . - Do not immerse the unit in water . If you spill liquid over it, dry it immediately with a soft, lint-free cloth .

- Do not clean the unit with abrasive or corrosive materials . - Do not tamper with the unit’s internal components . This invalidates the warranty . - Only use fresh batteries . Do not mix new and old batteries . - Only use attachments / accessories specified by the manufacturer. - Images shown in this manual may differ from the actual display . - When disposing of this product, ensure it is collected separately for special treatment . - Placement of this product on certain types of wood may result in damage to its finishing for which manufacturer will not be responsible . Consult the furniture manufacturer’s care instructions for information .

- The contents of this manual may not be reproduced without the permission of the manufacturer .

CLEANING THE THERMO/HYGRO SENSOR

2. Gently remove the rain collector.3. Clean and remove any debris or insects. 4. Wait until the parts are fully dry, and then reinstall them, and return the rain collector to a locked position.

1. Unscrew the 2 screws at the bottom of the sensor casing.2. Gently pull out the shield.3. Carefully remove any dirt or insects inside the sensor casing, making sure the inside sensors remain dry. 4. Clean the shield with water and remove any dirt or insects.5. Once the parts are fully clean and dry, reinstall them and replace the screws.

BATTERY REPLACEMENTIf the low battery indicator icon is displayed in the outdoor temperature and humidity section or the corresponding CH section of the LCD console display, this indicates that the batteries in your wireless weather sensor are running low and should be replaced. Make sure to replace all batteries at the same time.

CARE AND MAINTENANCE

20

TO SILENCE THE ALERT ALARMPress [ SNOOZE ] key to silence the alert alarm or let the alarm automatically turn off after 2 minutes.

NOTE: - Once the alert is triggered, the alarm will sound for 2 minutes and the related alert icon and readings will flash.

- If the alert alarm is automatically off after 2 minutes, the alert icon and readings will still keep flash until the weather reading is out of the alert range.

- The weather alert will sound again when the weather readings falls into the alert range again.

MAINTENANCEBATTERY REPLACEMENTIf the low battery indicator “ ” displayed in OUT or CH section, it indicates that the current channel wireless or outdoor 5-in-1 sensor battery power is low. You should replace all the batteries in the current channel sensor at once .

CLEANING THE RAIN COLLECTOR1 . Unscrew the rain collector by turning it 30°anti-clockwise.2 . Gently remove the rain collector.3 . Clean and remove any debris or insects.4 . Install the collector when it is clean and fully dried.

N N

“Unlock” Position“Lock” Position

N

CLEANING HYGRO-THERMO SENSOR OF WIRELESS 5-IN-1 SENSOR1 . Remove the 2 screws at the bottom of the radiation shield.2 . Gently pull out the shield.3 . Carefully remove any dirt or insects on the sensor casing (do not

let the sensors inside get wet).4 . Clean the shield with water to remove any dirt or insects.5 . Install all the parts back when they are clean and fully dried.

PRECAUTIONS - Keep and reading the “User manual” is highly recommended. The manufacturer and supplier cannot accept any responsibility for any incorrect readings, export data lost and any consequences that occur should an inaccurate reading take place.

- This product is designed for use in the home only as indication of weather conditions. This product is not to be used for medical purposes or for public information

- Do not subject the unit to excessive force, shock, dust, temperature or humidity. - Do not cover the ventilation holes with any items such as newspapers, curtains etc. - Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth .

- Do not clean the unit with abrasive or corrosive materials. - Do not tamper with the unit’s internal components. This invalidates the warranty. - Placement of this product on certain types of wood may result in damage to its finishing for which manufacturer will not be responsible. Consult the furniture manufacturer’s care instructions for information.

35

DISPLAY CONSOLE

SPECIFICATIONS

SPECIFICATIONSDISPLAY CONSOLE

Dimensions (W x H x D) 5.4″ x 6.6″ x 1″ (117 x 189 x 31mm)Weight 0.82 lb. (370g) with batteriesPower source DC 5V, 1A adaptorBackup battery CR2032, 3V batteryOperating temperature range

Wi-Fi standardWi-Fi operating frequency

23°F ~ 122°F (-5°C ~ 50°C)

802.11 b/g/n2.4GHz

Router security type WPA/WPA2, OPEN, WEP (WEP will only support a hexadecimal password)Supported devices for setup UI Smart devices, tablets, laptops, or PCs with built-in WI-FI and AP mode

functionality such as: Android™ phone or tablet, iPhone or iPad, or a Windows® laptop/PC

1 Wireless 5-in-1 weather outdoor sensor and up to 7 optional wireless hygro-thermo outdoor sensors

(700 ~ 1100 hPa ± 5 hPa) / (540 ~ 696 hPa ± 8 hPa)(20.67 ~ 32.48 inHg ± 0.15 inHg) / (15.95 ~ 20.55 inHg ± 0.24 inHg)(525 ~ 825mmHg ± 3.8mmHg) / (405 ~ 522 mmHg ± 6 mmHg)Typical at 77°F (25°C)

>104°F ± 3.6°F (>40°C ± 2°C) 32°F ~ 104°F ± 1.8°F (0~40°C ± 1°C)< 32°F ± 3.6°F (< 0°C ± 2°C)131°F ~ 140°F ± 0.9°F (55°C ~ 60°C ± 0.5°C)50°F ~ 131°F ± 0.7°F (10°C ~ 55°C ± 0.4°C)-4°F ~ 50°F ± 2.3°F (-20°C ~ 10°C ± 1.3°C)-40°F ~ -4°F ± 3.4°F (-40°C ~ -20°C ± 1.9°C)

20~39% RH ±8%RH @ 77°F (25°C)40~70% RH ±5%RH @ 77°F (25°C)71~90% RH ±8%RH @ 77°F (25°C)

868 MHz (EU or UK version), 915 MHz (US version), 917 MHz (AU version)

Recommended web browser version Latest version of any web browser that supports HTML 5

Supported sensors

RF frequencyRF transmission range 492 ft (150m)

Time display HH: MM: SS

General Specifications

WI-FI Communication Specifications

Wireless Sensor Communication Specifications

Barometer Display & Function Specifications

Time Function Specifications

Hour format 12 hour or 24 hourDate display DD / MM or MM / DDTime synchronization method Synchronizes with UTC clock through internet time serverWeekday languages EN / DE / FR / ES / IT / NL / RUTime zones GMT +13 ~ GMT -12DST ON / OFF

Note:

Indoor / Outdoor Temperature Display & Function Specifications

Indoor / Outdoor Humidity Display & Function Specifications

Wind Speed & Direction Display and Function SpecificationsNote:

Rain Display & Function SpecificationsNote:

Weather Index Display & Function SpecificationsNote:

Note:

The following details are listed as they are displayed or operate on the console.Barometer units hPa, inHg, and mmHgMeasuring range 540 ~ 1100 hPa (relative setting range 930 ~ 1050 hPa)

Accuracy

Resolution 1hPa / 0.01inHg / 0.1mmHgWeather forecast Sunny, Partly Cloudy, Cloudy, Rainy, Rainy / Stormy and SnowyDisplay modes CurrentMemory modes Historical data of past 24 hours, daily Max / MinAlarm Pressure change alert

The following details are listed as they are displayed or operate on the console.Temperature unit °C and °F

-40 ~ 176°F (-40 ~ 80°C)Display range

Indoor Accuracy

Outdoor Accuracy

Resolution 0.1°F / 0.1°C Display modes CurrentMemory modes Historical data of past 24 hours, Max / MinAlarm High / Low temperature alert

Note: The following details are listed as they are displayed or operate on the console.Humidity unit %

1%

Display range 1 ~ 99%

Indoor Accuracy

Outdoor Accuracy 1 ~ 90% RH ± 2.5% RH @ 77°F (25°C)90 ~ 99% RH ± 3.5% RH @ 77°F (25°C)

ResolutionDisplay modes CurrentMemory modes Historical data of past 24 hours, Max / MinAlarm High / Low Humidity Alert

The following detail are listed as they are displayed or operate on the console.Wind speed unit mph, m/s, km/h and knotsWind speed display range 0 ~ 112mph, 50m/s, 180km/h, 97knotsResolution 0.1mph, 0.1m/s, 0.1km/h, 0.1knotsSpeed accuracy ± 2.2 mph or ± 10% (whichever is greater)Display mode Gust / AverageMemory modes Historical Data of past 24 hours, daily Max Gust/ AverageAlarm Hi Wind Speed Alert (Average / Gust)Wind direction 16 direction

The following details are listed as they are displayed or operate on the console.Unit for rainfall mm and inAccuracy for rainfall ± 7%Range of rainfall 0 ~ 19999mm (0 ~ 787.3 in)Resolution 0.254mm (0.01in)Display modes CurrentMemory modes Historical Data of past 24 hours, daily MaxRainfall display mode Hourly / Daily / Weekly / Monthly / Total rainfallAlarm High Hourly Rainfall Alert

The following details are listed as they are displayed or operate on the console.Weather index mode Feels like, Wind Chill, Heat Index and Dew pointBeaufort scale 0 ~ 12Wind Chill range -40°F ~ 64.4°F (-40°C ~ 18°C), wind speed > 4 .8km/hHeat index range 78.8°F ~ 122°F (26°C ~ 50 °C)Dew point range -4°F ~ 140°F (-20°C ~ 60°C)Display modes CurrentMemory modes Historical Data of past 24 hours, Daily Max / MinWireless 5-in-1 Sensor SpecificationsDimensions (W x H x D) 13.5″ x 15.5″ x 5.35″ (343.5 x 393.5 x 136 mm)Weight 1.62 lb. (734g) with batteriesMain power source 3 x AA 1.5V batteries (lithium batteries recommended)Weather data recorded Temperature, humidity, wind speed, wind direction, and rainfallRF Transmission range 492 ft (150m)RF frequency 868 MHz (EU or UK version), 915 MHz (US version), 917 MHz (AU version)

Transmission interval • Every 12 seconds: wind speed and wind direction• Every 24 seconds: temperature, humidity, and rain

Operating range -40°F ~ 140°F ( -40°C ~ 60°C)

36




23°F ~ 122°F (-5°C ~ 50°C)

802.11 b/g/n2.4GHz









Supported sensors









Note:






Note:


Accuracy



-40 ~ 176°F (-40 ~ 80°C)Display range

Indoor Accuracy

Outdoor Accuracy



1%


Indoor Accuracy








37




23°F ~ 122°F (-5°C ~ 50°C)

802.11 b/g/n2.4GHz









Supported sensors









Note:






Note:


Accuracy



-40 ~ 176°F (-40 ~ 80°C)Display range

Indoor Accuracy

Outdoor Accuracy



1%


Indoor Accuracy








FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and; (2) This device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates—and can radiate—radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If the equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna • Increase the separation between the equipment and the receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the unit at least 20cm from nearby persons.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

38

WARRANTY INFORMATIONLIMITED WARRANTY ON LOGIA™ 5-IN-1 WIRELESS WEATHER STATION WITH WI-FI

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

WE WARRANT THAT DURING THE WARRANTY PERIOD, THE PRODUCT WILL BE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP.

LIMITATION OF LIABILITYTO THE EXTENT NOT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL

OTHER WARRANTIES, ORAL, WRITTEN, STATUTORY, EXPRESS OR IMPLIED. EXCEPT FOR THE EXPRESS WARRANTIES CONTAINED IN THIS LIMITED WARRANTY STATEMENT AND TO THE EXTENT NOT PROHIBITED BY LAW, WE DISCLAIM ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, STATUTORY OR OTHERWISE,

INCLUDING WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW DISCLAIMERS OF IMPLIED WARRANTIES, SO THIS

DISCLAIMER MAY NOT APPLY TO YOU. TO THE EXTENT SUCH WARRANTIES CANNOT BE DISCLAIMED UNDER THE LAWS OF YOUR JURISDICTION, WE LIMIT THE DURATION AND REMEDIES OF SUCH

WARRANTIES TO THE DURATION OF THIS EXPRESS LIMITED WARRANTY.OUR RESPONSIBILITY FOR DEFECTIVE GOODS IS LIMITED TO REPAIR, REPLACEMENT OR REFUND AS

DESCRIBED BELOW IN THIS WARRANTY STATEMENT.

WHO MAY USE THIS WARRANTY? C&A Marketing, Inc. located at 114 Tived Lane East, Edison, NJ (“we”) extend this limited warranty only to the consumer who originally purchased the product (“you”). It does not extend to any subsequent owner or other transferee of the product.WHAT DOES THIS WARRANTY COVER? This limited warranty covers defects in materials and workmanship of the Logia™ 5-in-1 Wireless Weather Station with WI-FI (the “product”) for the Warranty Period as defined below.WHAT DOES THIS WARRANTY NOT COVER? This limited warranty does not cover any damage due to: (a) transportation; (b) storage; (c) improper use; (d) failure to follow the product instructions or to perform any preventive maintenance; (e) modifications; (f) unauthorized repair; (g) normal wear and tear; or (h) external causes such as accidents, abuse, or other actions or events beyond our reasonable control.WHAT IS THE PERIOD OF COVERAGE? This limited warranty starts on the date of your purchase and lasts for one year (the “Warranty Period”). The Warranty Period is not extended if we repair or replace the product. We may change the availability of this limited warranty at our discretion, but any changes will not be retroactive.WHAT ARE YOUR REMEDIES UNDER THIS WARRANTY? With respect to any defective product during the Warranty Period, we will, at our sole discretion, either: (a) repair or replace such product (or the defective part) free of charge or (b) refund the purchase price of such product if an exchange unit cannot be provided. HOW DO YOU OBTAIN WARRANTY SERVICE? To obtain warranty service, you must contact us at 1-833-815-0568 or by email at [email protected] during the Warranty Period to obtain a Defective Merchandise Authorization (“DMA”) number. No warranty service will be provided without a DMA number and return shipping costs to our facilities shall be assumed by you, the purchaser. Shipping costs of the replacement unit to you shall be assumed by us.

39

If you experience any issues with your Logia™ 5-in-1 Wireless Weather Station with WI-FI, please contact us before returning your product to the place of purchase. We’re here to help!

QUESTIONS OR PROBLEMS? CONTACT US!Email: [email protected] or call: 1-833-815-0568 www.logiaweatherstation.com

LOGIA is a trademark of C&A IP Holdings, LLC, in the U.S.

Android is a trademark of Google LLC. Apple and App Store are trademarks of Apple Inc. in the U.S. and other countries. IOS is a trademark of Cisco in the U.S. and other countries and is used under license.

Microsoft, Windows, Windows Server, Windows Vista, and Windows 10 are trademarks of Microsoft Corporation in the U.S. and/or other countries. WI-FI, WPA, and WPA2 are trademarks of WI-FI Alliance in the U.S. and/or other countries.

All other products, brand names, company names, and logos are trademarks of their respective owners, used merely to identify their respective products, and are not meant to connote any sponsorship, endorsement or approval.

Distributed by C&A Marketing, Inc., 114 Tived Lane East, Edison, NJ 08837. Made in China.

© 2019. C&A IP Holdings, LLC. All Rights Reserved.

122319 logia 5-in-1 wireless weather station with wi-fi

Documents