110120 pdg a4001n user manual cover - movistar · in the dns configuration panel (see figure 16),...

P.DG A4001N

User Manual

Copyright © 2011 ADB Broadband S.p.A. All rights reserved. This document contains ADB proprietary and confidential infor-

mation. No part of this document may be copied, reprinted or reproduced in any material form or electronically, whether wholly

or in part, and no information contained herein may be used or disclosed to third parties unless under a previous written agree-

ment with ADB Broadband S.p.A setting forth relevant terms and conditions.

Trademarks:

All terms used in this document that are known to be trademarks or service marks have been noted as such. ADB cannot attest

to the accuracy of this information. Other product and corporate names used in this document that may be trademarks or ser-

vice marks of other companies are used only for explanation and to the owner’s benefit, without intent to infringe. Use of a term

in this document should not be regarded as affecting the validity of any trademark or service mark.

This publication is subject to change without notice. ADB reserves the right to make changes to equipment design and system

components as well as system documentation and literature as progress in engineering, manufacturing methods, or other cir-

cumstances may warrant.

This publication is intended solely for informational and instructional purposes. Refer to the above as to its possible uses. It con-

stitutes neither a contract with the user hereof nor a warranty or guarantee with regard to any of the ADB products described

herein nor shall it be construed to grant a license or any other rights under any proprietary rights to information or material in-

cluded herein. ADB hereby expressly disclaims any warranty or guarantee, whether express or implied, with regard to items de-

scribed herein. Any contract, license, or warranty between ADB and the user hereof is created solely by separate legal docu-

ments.

Home Station ADSL ADB P.DG A4001N

© (2011) ADB Broadband S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.

i

CONTENTS

Welcome 1

About this Guide 1 Naming Convention 1 Conventions 1

Procedures 3

How to change Access Password 3 How to open ports 4 How to Upgrade the Firmware 6 How to how to configure the ADSL line addessing >> static with RFC1483 7 How to how to configure the ADSL line addessing >> dinamic with PPPoE 12 How to configure the LAN access 17


Welcome 1

Welc

om

e

Welcome

ABOUT THIS GUIDE

This guide describes the most relevant user procedures for the Home Station ADSL

ADB P.DG A4001N. This guide is intended for use by those responsible for support-

ing the installation and setup of network equipment; consequently, it assumes a

basic working knowledge of LANs (Local Area Networks) and Internet Routers.

NAMING CONVENTION

Throughout this guide, the P.DG A4001N

Category 5 Ethernet Cables are referred to as Ethernet Cables throughout this guide.

CONVENTIONS

Table 1 and Table 2 list conventions that are used throughout this guide.

TABLE 1. Notice Icons

Icon Notice Type Description

Information note Information that describes important features or instruc-tions.

Caution Information that alerts you to potential loss of data or po-tential damage to an application, system, or device.



2 Welcome

TABLE 1. Notice Icons

Icon Notice Type Description

Warning Information that alerts you to potential personal injury.

TABLE 2. Text Conventions

Convention Description

e-thing, and then press Return or Enter. Do not press Return or Enter when an instruction simply says

Keyboard key names If you must press two or more keys simultaneously, the key names are linked with a plus sign (+). Example:

Press Ctrl+Alt+Del

Words in italics Italics are used to:

Emphasize a point.

Denote a new term at the place where it is defined in the text.

Identify menu names, menu commands, and software button

Help menu, select Contents. Click OK


Procedures 3

Pro

cedure

s

Procedures

This chapter is dedicated to the main how-to procedures description. For a more

complete device description and operative guidelines, please refer to the product

Administrator Manual.

HOW TO CHANGE ACCESS

PASSWORD

Please follow below procedure s

Open your web browser and connect to http://192.168.1.1/main.html

Select from the left menu the it -

For the selected account, insert in the related input box the curre

to confirm your changes.

http://192.168.1.1/main.html



4 Procedures

FIGURE 1. Access Password Change panel

HOW TO OPEN PORTS

Some applications require that specific ports in the Router's firewall be opened for

access by the remote parties. Port Trigger dynamically opens up the 'Open Ports' in

the firewall when an application on the LAN initiates a TCP/UDP connection to a re-

mote party using the 'Triggering Ports'. The Router allows the remote party from

the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured.

Please follow below steps to learn how to open ports in the firewall:


-

In the shown panel (see

port

A new panel (see Figure 3) will be shown: you can configure the port set-

tings from this screen by selecting an existing application or creating your own (Custom application)

In the table, insert the Trigger port range, Trigger protocol, Open port range




Procedures 5

FIGURE 2. Port Triggering panel

FIGURE 3. Port Triggering panel #2



6 Procedures

HOW TO UPGRADE THE

FIRMWARE

Please follow below steps to learn how to update the device firmware:

Obtain an updated software image file from your ISP


Insert the a

- p-

Enter the path to the image file location in the box or click the "Browse" button to locate the image file

Click the "Update Software" button once to upload the new image file.

The update process takes about 2 minutes to complete, and your Router will reboot.

FIGURE 4. Firmware Upgrade panel




Procedures 7

HOW TO HOW TO

CONFIGURE THE ADSL LINE ADDESSING >> STATIC WITH

RFC1483

To configure a static ADSL line addressing it is necessary to configure the ATM and WAN interface according to below steps:


-

Please verify to have the following settings:

o VPI = 8

o VCI = 35

o DSL Latency = Path0 (Path1 deselected)

o DSL Link type = IPoA

o Encapsulation Mode = LLC/SNAP-ROUTING

o Service Category = CBR

o Peak Cell Rate = 452

o Enable IP QoS NOT checked

FIGURE 5. ATM Interface Configuration




8 Procedures

ly changes

-item

In the shown panel, please insert:

o Service Description = PVC: 8/35

FIGURE 6. WAN Service panel

In the WAN IP Settings panel (see Figure 7), please insert:

o WAN IP Address = 172.26.208.12

o WAN Subnet Mask = 255.255.240.0

FIGURE 7. WAN IP Settings panel



Procedures 9

In the Network Address Translation Settings panel (see Figure 8), please in-

sert:

o Enable NAT NOT checked

o Enable Firewall NOT checked

o Enable IGMP Multicast checked

FIGURE 8. Network Address Translation panel

In the Routing Default Gateway panel (see Figure 9), please check to have the ipoa0



10 Procedures

FIGURE 9. Routing Default Gateway panel

In the DNS Server Configuration panel (see Figure 10), please insert:

o Select DNS Server Interface from available WAN Interfaces NOT checked

o Use the following static DNS IP Address checked with

Primary DNS Server = 80.58.61.250

Secondary DNS Server = 80.58.61.254



Procedures 11

FIGURE 10. DNS Server Configuration panel

In the WAN Setup Summary (see Figure 11), please verify that:

o Connection type = IPoA

o NAT = Disabled

o Full Cone NAT = Disabled

o Firewall = Disabled

o IGP Multicast = Enabled

o Quality of Service = Disabled



12 Procedures

FIGURE 11. WAN Setup Summary panel

HOW TO HOW TO CONFIGURE THE ADSL LINE

ADDESSING >> DINAMIC WITH PPPOE

To configure a dynamic ADSL line with PPPoE addressing it is necessary to configure

the ATM and WAN interface according to below steps. Please consider that this pro-

cedure will allow you to configure two pvc: the second allowed pvc configuration in

below indicated between square brackets. Contact your ISP to know which one of them is the proper one.


-




Procedures 13

FIGURE 12. ATM Interface panel

Please verify to have the following settings:

o VPI = 8

o VCI = 35 [36]

o DSL Latency = Path0 (Path1 deselected)

o DSL Link type = EoA

o Encapsulation Mode = LLC/SNAP-ROUTING

o Service Category = UBR without PCR [UBR with PCR]

o [Peak Cell Rate = 301]

o Strict priority checked

o Weighted Fair Queuing not checked

o [Enable IP QoS checked]]

-item



14 Procedures

FIGURE 13. WAN Service panel

In the shown panel, please insert:

o Select WAN Service type = PPP over Ethernet

o Enter Service Description = PVC: 8/35 [PVC: 8/36]

Click on the Next button to proceed

In the shown PPP and password panel (see Figure 14), please insert:

o PPP username = (given user name)

o PPP password = (given password)

o PPPoE Service name = empty

o Authentication Method = AUTO

o ALL remaining fields must be unchecked




Procedures 15

FIGURE 14. PPP and password panel

In the Routing Default Gateway panel (see Figure 15), please verify to

have your pppo [ppp1] interface in the Selected Default Gateway Interfaces box


FIGURE 15. Routing Default Gateway panel



16 Procedures

In the DNS Configuration panel (see Figure 16), please verify that:

o Select DNS Server Interface form available WAN Interfaces is un-checked

o Use the following Static DNS IP Address:

Primary DNS Server = 80.58.61.250

Secondary DNS Server = 80.58.61.254


FIGURE 16. DNS Configuration panel



Procedures 17

In the WAN Setup Summary panel (see Figure 17) please verify that:

o Connection type = PPPoE

o NAT = Enabled

o Full Cone NAT = Disabled

o Firewall = Enabled

o IGP Multicast = Disabled

o Quality of Service = Disabled

FIGURE 17. WAN Setup Summary panel

HOW TO CONFIGURE THE LAN ACCESS

To configure LAN interface it is necessary to follow below steps:





18 Procedures

Sele -

(see Figure 18)

Please verify to set the following fields:

o IP Address = (router address: 192.168.1.1 by default)

o Subnet mask = 255.255.255.0

o Enable IGMP Snooping not checked

o Enable LAN side firewall not checked

o Enable DHCP server checked:

Start IP Address = first IP Address in the allowed IP range

End IP Address = last IP Address in the allowed IP range

Leased Time (hour) = 24

Static IP Lease list = MAC Address and IP Address till a

max of 32entries to be added/removed for a static IP as-

o Configure the second IP Address and Subnet Mask for LAN inter-face:

IP Address = 192.168.249.1

Subnet Mask = 255.255.255.252

FIGURE 18. LAN panel



Procedures 19

ADB Broadband S.p.AViale Sarca 22220126 Milano

http://broadband.adbglobal.com

110120 pdg a4001n user manual cover - movistar · in the dns configuration panel (see figure 16),...

Documents