11 unnoticeable but important things to know while buying carports!!
TRANSCRIPT
Carport CentralIMPORTANT POINTS YOU SHOULD REMEMBER BEFORE BUYING A CARPORT…
http://www.carportcentral.com
IndexSpecial PermitsPreparation of ground siteRoof StylesWidthLengthHeight Side
CertificationsGable EndsSide PanelsJ trimsClosed sides About us
http://www.carportcentral.com
Permits
Generally, you need to have a permit, if you are planning to have a new construction project whether it be installing a new carport/garage or expanding the existing ones. It's necessary to have a permit such as:-
-Building Permit,
-Electric Permit etc.
for the security purposes. So please be sure to get any permit required in your area and then go with the structure you would like to have.
http://www.carportcentral.com
Ground level(Flat land does not mean that the land is Level).
Proper
To make sure the custom carport is installed in the safest and securest possible manner, it is important to prepare the surface and the foundation on which that the carport or structure will rest.
Might end up leaning to one end or one side. This could compromise not only your carport, but also the contents within it. You are also inviting various animals (snakes, mice, and other critters) to find their way through the gaps into your enclosure.
Improper
http://www.carportcentral.com
A- Frame (Boxed Eave)
It is more affordable since it does not have the hat channel and ridge cap that the vertical roof has to support the vertical panels. The roof bow/truss has a welded transition via a steel pin onto the legs. The underneath eave sides of the roof bow or truss is covered with boxed eave trim for a nice
finished appearance.
http://www.carportcentral.com
Vertical Style
This allows dirt, trash, water, and snow to exit off to the eave side of the building. Steel panels on home and business roof-tops are always installed vertically. The roof bow/truss has a welded transition via a steel pin on to the legs. This unit has vertical roof trim on the sides
and ends for a finished appearance as well as hat channel to support the vertical panels and it adds rigidity to the structure
http://www.carportcentral.com
Regular Style Carports
Regular Frame Design with the panels are installed horizontally. The corrugated ridges in the panel run from front to back or end to end. The regular style is the most economical unit since it does not have the hat
channel, the ridge cap, the eave-side trim, nor the welded transition from the roof bow/truss to the leg.
http://www.carportcentral.com
Width- Selecting the right size is
important.
- You should make sure that the custom carport will be
wide enough for your vehicle or equipment for which you
intend to use it.
- Carports come in standards widths of 12’, 18’, 20’, 22’, 24’, 26’, 28’, 30’, 32’, 34’ 36’, 38’,
and 40
For instance:
12’ - Single car, truck or RV
18’ - Two compact cars
20’ - Two midsized cars
22’ - Two full sized cars, trucks or SUV
24’ - Two full or oversized cars or trucks
26’ - Three midsized cars or truck
http://www.carportcentral.com
Length
AGAIN! Will you store only one car, or multiple cars in your new metal
carport?
The industry standard length for prefabricated carports are 21’, 26’,
31’, and up in 5’ increments.
Note: The roof of every structure is always longer than the base due to a 6” overhang on each end of the roof.
http://www.carportcentral.com
Side Height
Steel carport height is measured by the side height,
meaning the height on the sides of the structure, not from the very top point of
the roof to the ground.
The standard option offered on metal carports is 6’ height
with the height requirements increasing to 8’
for any structure 32’ or wider.
Side height is used to make sure a vehicle can clear the lowest point of the carport.
http://www.carportcentral.com
Certifications• Johnston – Wilson – wake
• Pender – Carteret – NashNC - County (Certified & Certified Doors)
• Spartanburg – Richland – Charleston
• Berkeley –Marlboro – Horry
• City of Bennettsville – City of Newberry
• City of Moncks Corner – City of Wellford
SC – County (City Just certified)
• Marion – Okeechobee – Putham
• Bay – St johns –Hillsborough
• Brevard
Florida State(must be certified
with certified doors)
http://www.carportcentral.com
Continued..• all carports & garages must be certified
New Jersey State
• in Lowndes county customer will have to get a permit but not necessarily certified buildingState of Georgia
• parish that have to be certified
• ascension – St-john the BaptistState of LA
• City of Mineola - have to pull a permit
State of TX
http://www.carportcentral.com
Continued..• Belleville – Granite city
State of Illinois
• Saint louis + Wichita – Lawrence – Topeka –Manhattan
• Kansas city - ( colors must match the house colors) & can’t install over 400 sq. ft.
State Missouri
• Richmond – Columbia – ChathamCounties that have to be certified
• Lee – St-john – Hernando
• Pasco – Hillsborough
• Volusia
As built plans
http://www.carportcentral.com
Gable Ends
Appearance – hides frame and braces
Provides additional side-to-side strength due to additional framing support and steel panel
Provides better protection from sun and from blowing rain on the ends.
Increase the appearance by concealing the frame
and braces
http://www.carportcentral.com
Side Panels(Add extra strength and support to your custom metal carport or RV carport)
Provides better protection from the sun,
wind, and rain
Provides additional strength from back to
front
All RV carports 10’ and taller should have at least one panel on each side of the
carport.
http://www.carportcentral.com
J Trim
Safety – Panel edges are not exposed
Appearance – Gives a nice finished look
Applied to the edges of panels so they are not exposed for safety and it also gives the unit a nice finished look.
http://www.carportcentral.com
About us..
http://www.carportcentral.com
Learn More at – http://carportcentral.comCall us at - (980) – 321-9898 or TOLL FREE (844) 860-4950
Email – [email protected]