0671p resene painting - web view0671p resene painting. branded worksection. this branded worksection...

06 FINISH 0671p RESENE painting

0671P RESENE PAINTING

1 GENERAL

1.1 RESPONSIBILITIES

GeneralRequirement: Provide RESENE coating systems to substrates, as documented.

PerformanceRequirement: Provide coating systems as follows:

- Consistent in colour, gloss level, texture and dry film thickness.

- Free of runs, sags, blisters, or other discontinuities.

- Paint systems which are fully opaque or at the documented level of opacity.

- Clear finishes at the level of transparency consistent with the product.

- Fully adhered.

- Resistant to environmental degradation within the manufacturer’s stated life span.

1.2 COMPANY CONTACTS

Resene technical contactsWebsite: www.resene.com.au

1.3 CROSS REFERENCES

GeneralRequirement: Conform to the following:

- 0171 General requirements.

1.4 STANDARDS

PaintingGeneral: To the recommendations of those parts of AS/NZS 2311 referenced in this worksection.

1.5 MANUFACTURER'S DOCUMENTS

Technical manualsProduct: Refer to Resene One-Line Specifications and Product Data Manual (hard copy or view online at www.resene.com.au).

Safety: Submit the Resene published safety data sheets (SDS) showing the health and safety precautions to be taken during application.

1.6 INTERPRETATION

DefinitionsGeneral: For the purposes of this worksection the definitions in AS/NZS 2310 and the following apply:

- Gloss: The optical property of a surface, characterised by its ability to reflect light specularly.

- Gloss unit: Numerical value for the amount of specular reflection relative to that of a standard surface under the same geometric conditions.

- Levels Of Gloss Finish: When the specular direction is 60 degrees, surfaces with the following specular gloss reading is defined as follows:

. Full gloss: Over 85 gloss units.

© NATSPEC (Oct 17) 1 "[Insert date]"

http://www.resene.com.au/

http://www.resene.com.au/


. Gloss: Between 50 and 85 gloss units.

. Semi-gloss: Between 20 and 50 gloss units.

. Low gloss (low sheen): Between 5 and 20 gloss units.

. Flat finish (matt): Up to 5 gloss units.

- Opacity: The ability of a paint or textured and membrane coating to obliterate the colour difference of a substrate.

- Paint or coating system: A product in liquid form, which when applied to a surface, forms a dry film having protective, decorative or other specific technical properties.

- Primer, prime coat: The first coat of a painting system that helps bind subsequent coats to the substrate and which may inhibit its deterioration.

- Sealer: A product used to seal substrates to prevent the following:

. Materials from bleeding through to the surface.

. Reaction of the substrate with incompatible top coats.

. Undue absorption of the following coat into the substrate.

- Substrate: The surface to which a material or product is applied.

- Undercoat: An intermediate coat formulated to prepare a primed surface or other prepared surface for the finishing coat.

1.7 SUBMISSIONS

SamplesClear finish coating: Submit samples of timber or timber veneer matching those to be used in the works as follows:

- Requirement: Label for identification and prepare, putty, stain, seal and coat in conformance with the documented system.

- Size: Large enough to be cut into 4 segments.

Opaque coated samples: Submit labelled samples of each coating system, on representative substrates, showing surface preparation, colour, gloss level, texture, and physical properties.

Control reference: Check Resene colour samples before application and keep the Resene colour samples on site as a control reference. Colour matches are not permitted as they will differ in appearance, durability and performance to the original selected colour over the life of the coating.

Coated samples scheduleSubstrate Paint system Colour Sample size

Plasterboard Flat waterborne: Interior Off white 50 x 300 mm

SubcontractorsSpecialist applicators: Submit names and contact details of proposed specialist applicators.

Evidence of experience: [complete/delete]

WarrantiesGeneral: Submit the coating manufacturer’s warranties as follows:

- [complete/delete]



1.8 INSPECTION

NoticeInspection: Give notice so that inspection may be made of the following:

- Painting stages:

. Completion of surface preparation.

. After application of final coat.

- Clear finishing stages:

. Before surface preparation of timber.

. Completion of surface preparation.

. After application of final coat.

2 PRODUCTS

2.1 GENERAL

Product substitutionOther products: Conform to PRODUCTS, GENERAL, Substitutions in the 0171 General requirements worksection.

Storage and handlingGeneral: Store materials not in use in tightly covered containers in well-ventilated areas with temperatures maintained at the manufacturer’s recommendations.

Delivery: Deliver paints to the site in the manufacturer’s labelled and unopened containers.

MarkingIdentification: Marked to show the following:

- Manufacturer’s identification.

- Product brand name.

- Product type.

- Quantity.

- Product reference code and batch number.

- Date of manufacture.

- Material composition and characteristics such as volatility, flash point, light fastness, colour and pattern.

2.2 PAINTING MATERIALS

CombinationsGeneral: Do not combine paints from different manufacturers in a paint system.

Clear timber finish systems: Provide only the combinations of putty, stain and sealer recommended by the manufacturer of the topcoats.

Putty and fillersMaterial: To the recommendations of Resene, suitable for the substrate and compatible with the primer.

TintingGeneral: Provide only products which are colour tinted by the manufacturer or supplier.

Toxic ingredientsGeneral: To the Poisons Standard June 2017 (including SUSMP 17) Part 2 Section 7.



Low VOC compliance reference tableNOTE: COMPLIANCE CRITERIA – GBCA specifications (obtain latest figures from GBCA).

Green Star submission guidelines Product Type

VOC Limits MAX g/litre

Resene Products compared to the GBCA specification

VOC g/litre (inc tint using Resene non VOC tinters)

Walls - interior low sheen 16 Resene Zylone Sheen VOC Free D302

0

Walls - interior flat 16 Resene Sandtex Standard and Superfine D71 (textured)

12

Ceilings - interior flat 14 Resene Ceiling Paint D305

1

Trim - exterior/interior gloss

75 Resene Enamacryl Gloss Waterborne Enamel D309a

63

Trim - exterior/interior semi-gloss

75 Resene Lustacryl Semi-Gloss Waterborne Enamel D310

63

Trim - interior semi-gloss 75 Resene Lustacryl Kitchen & Bathroom Semi-Gloss Waterborne Enamel D310K

63

Trim - exterior satin 75 Resene Lumbersider D34

35

Trim - exterior satin 75 Resene Waterborne Sidewalk D38a

30

Trim - low sheen 75 Resene SpaceCote Low Sheen Waterborne Enamel D311

55

Trim - low sheen 75 Resene SpaceCote Low Sheen Kitchen & Bathroom Waterborne Enamel D311K

55

Trim - flat 75 Resene SpaceCote Flat Waterborne Enamel D314

55

Interior latex undercoat 65 Resene Quick Dry 53


http://www.resene.com.au/archspec/datashts/d314_SpaceCote_Flat.pdf

http://www.resene.com.au/archspec/datashts/d311K_Spacecote_Low_Sheen_K.pdf

http://www.resene.com.au/archspec/datashts/d311_Spacecote_Low_Sheen.pdf

http://www.resene.co.nz/archspec/datashts/d38a_Waterborne_Sidewalk.pdf

http://www.resene.co.nz/archspec/datashts/d34_Lumbersider.pdf

http://www.resene.com.au/archspec/datashts/d310K_LustacrylKitchenandBathroom.pdf

http://www.resene.com.au/archspec/datashts/d310_Lustacryl_WB_Enamel.pdf

http://www.resene.co.nz/archspec/datashts/d309_Enamacryl_WB_Enamel.pdf

http://www.resene.co.nz/archspec/datashts/d305_Ceiling_Paint_Flat.pdf

http://www.resene.co.nz/archspec/datashts/d71_Sandtex_Coating.pdf

http://www.resene.co.nz/archspec/datashts/d302_Zylone_Sheen_Acrylic.pdf


Green Star submission guidelines Product Type

VOC Limits MAX g/litre

Resene Products compared to the GBCA specification

VOC g/litre (inc tint using Resene non VOC tinters)

Waterborne Primer Undercoat D45

Interior sealer 65 Resene Broadwall Surface Prep & Seal D807

27

Interior sealer 65 Resene Broadwall 3 in 1 D810

2

Interior sealer 65 Resene Broadwall Waterborne Wallboard Sealer D403

0

Interior sealer 65 Resene Waterborne Smooth Surface Sealer D47a

< 10

3 EXECUTION

3.1 PREPARATION

Order of workOther trades: Before painting, complete the work of other trades as far as practicable within the area to be painted, except for the installation of fittings, floor sanding and laying flooring materials.

Clear finishes: Complete clear timber finishes before commencing opaque paint finishes in the same area.

ProtectionGeneral: Before painting, clean the area and protect it from dust contamination. Use drop sheets and masking agents to protect surfaces, including finished surfaces and adjacent finishes, during painting.

Fixtures and furniture: Remove door furniture, switch plates, light fittings and other fixtures before painting, and conform to the following:

- Labelling and storage: Attach labels or mark fixtures using a non-permanent method, identifying location and refixing instructions, if required. Store and protect against damage.

Difficult to remove fixtures: Where removal is impractical or difficult, apply surface protection before substrate preparation and painting.

Wet paint warningNotices: Place in a conspicuous location and do not remove until the paint is dry.

Substrate preparation – generallyGeneral: Prepare substrates to receive the painting systems to the paint manufacturer’s recommendations.


http://www.resene.co.nz/archspec/datashts/d47a_WBSmoothSurfaceSealer.pdf

http://www.resene.co.nz/archspec/datashts/d403_Broadwall_Sealer.pdf

http://www.resene.co.nz/archspec/datashts/d810_Broadwall_3in1.pdf

http://www.resene.co.nz/archspec/datashts/d807_Broadwall_Surface_Prep.pdf

http://www.resene.co.nz/archspec/datashts/d45_QuickDryPrimerUndercoat.pdf


Cleaning: Clean down the substrate surface. Do not cause damage to the substrate or the surroundings.

Filling: Fill cracks and holes with fillers, sealants, putties or grouting cements as appropriate for the finishing system and substrate, and sand smooth.

- Clear finish: Provide filler tinted to match the substrate.

Clear timber finish systems: Prepare the surface so that its attributes will show through the clear finish without blemishes, using methods including the following:

- Removal of bruises.

- Removal of discolourations, including staining by oil, grease and nailheads.

- Bleaching where necessary to match the timber colour sample.

- Puttying.

- Fine sanding, with the last abrasive no coarser than 220 grit, so that there are no scratches across the grain.

Treated surfaces: If surfaces have been treated with preservatives or fire retardants, make sure coating is compatible with the treatment and does not adversely affect its performance.

Unpainted surfacesStandard: To AS/NZS 2311 Section 3.

Previously painted surfacesCondition of substrate: [complete/delete]

Location of substrate in good condition: [complete/delete]

Location of substrate in poor condition: [complete/delete]

Preparation of a substrate in good condition: To AS/NZS 2311 clause 7.4.

Preparation of a substrate in poor condition: To AS/NZS 2311 clause 7.5.

Preparation of steel substrates with protective coatings: To AS/NZS 2312.1 Section 8 and AS 1627.1.

PVC-U: Clean with methylated spirit and a nylon scouring pad.

Wallpaper: Remove wallpaper and residual paste with clean water. Patch and repair substrate to a uniform surface before painting.

Lime wash paints: Remove by brushing with warm water.

Cleaning external surfacesSound external surfaces other than timber: Remove dirt, grease, loose and foreign matter, efflorescence and mould by water blasting or steam cleaning without damaging the surface. Remove remaining loose material with appropriate hand tools. Use sanding blocks to preserve the arrises of masonry and stone details.

Efflorescence: Eliminate the source of salt and water before cleaning. Allow surface to dry for 15 to 30 days before repainting.

New masonry: Allow 30 days for the masonry to cure and pH level to stabilise before painting.

Particular preparation requirements scheduleSubstrate Preparation method Applicable standard



3.2 PAINTING

GeneralRequirement: Refer to Resene One-Line Specifications and Product Data Manual data sheets and the requirements of this work section.

Light levelsGeneral: ≥ 400 lux.

Substrate moisture contentRequirement: Use a moisture meter to demonstrate that the moisture content of the substrate is at or below the recommended maximum level for the type of paint and the substrate material.

Paint applicationStandard: To AS/NZS 2311 Section 6.

Timing: Apply the first coat immediately after substrate preparation and before contamination of the substrate can occur. Apply subsequent coats after the manufacturer’s recommended drying period has elapsed.

Painting conditionsGeneral: Unless the paint is recommended for such conditions, do not paint under the following conditions:

- Dusty conditions.

- Relative humidity: > 85%.

- Surface temperature: < 10°C or > 35°C.

Priming before fixingGeneral: Apply one coat of wood primer, and 2 coats to end grain, to the back of the following before fixing in position:

- External fascia boards.

- Timber door and window frames.

- Bottoms of external doors.

- Associated trims and glazing beads.

- Timber board cladding.

SprayingGeneral: If the paint application is by spraying, use conventional or airless equipment which conforms to the following:

- Satisfactorily atomises paint being applied.

- Does not require paint to be thinned beyond the maximum amount recommended by the manufacturer.

- Does not introduce oil, water or other contaminants into the applied paint.

Paint with known health hazards: Provide personal protection, masking, ventilating and screening facilities to AS/NZS 4114.1 and AS/NZS 4114.2.

SandingClear finishes: Sand the sealer using abrasives no coarser than 320 grit without cutting through the colour. Take special care with round surfaces and edges.

RepairRequirement: Clean off marks, paint spots and stains progressively and restore damaged surfaces to their original condition.

Maintenance painting: To AS/NZS 2311 Section 8.



Repair of galvanizingCleaning: For galvanized surfaces which have been subsequently welded, power tool grind to remove all surface contaminants, including rust and weld splatter. Prime affected area immediately after cleaning.

Primer: Type 2 organic zinc-rich coating for the protection of steel to AS/NZS 3750.9.

TintingGeneral: Tint each coat of an opaque coating system so that each has a noticeably different tint from the preceding coat, except for top coats in systems with more than one top coat.

ServicesGeneral: Paint all new services and equipment, including those in plant rooms, if not embedded, except chromium, anodised aluminium, GRP, PVC-U, stainless steel, non-metallic flexible materials and normally lubricated machined surfaces.

Proprietary items: Repaint only if damaged.

WindowsOperation: Make sure opening windows function correctly before and after painting.

DoorsDrying: Maintain door leaf in the open position during drying. Do not allow door hardware or accessories to damage the door finish during the drying process.

3.3 COMPLETION

GeneralProtection and masking: Remove masking and protection coverings before paint has dried.

Cleaning: On completion of painting, remove splatters by washing, scraping or other methods which do not scratch or damage adjacent finished surfaces.

Reinstatement: Repair, replace or refinish any damage, including works of other trades. Touch up new damaged decorative paintwork or misses only with the paint batch used in the original application.

Removed fixtures: Refix undamaged fixture in the original location, make sure they are properly fitted and in proper working order.

Disposal of paint and waste materials.Requirement: Conform to requirements of the local government authority.

4 SELECTIONS

4.1 EXTERIOR PAINTING SCHEDULES

Paint system schedulesPaint system: To the EXTERIOR PAINT SYSTEM clause identified by the Resene Specification Number.

Exterior finishes scheduleSubstrate Resene Spec Number Colour

4.2 EXTERIOR PAINT SYSTEMS



Exterior cementitious surfacesDescription Resene One-

Line SpecSurface prep Surface prep 2nd coat 3rd coat

Exterior cementitious surfaces, waterborne gloss

1e 1.1 D83

For thin plaster - Resene Limelock D809, waterborne cure/seal

For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or

For powdery surfaces - Resene Sureseal D42, solvent-borne sealer

Resene Hi-Glo D31, waterborne gloss

Resene Hi-Glo D31, waterborne gloss 4th coat: Resene Multishield+ D54a, waterborne glaze (optional)

Exterior cementitious surfaces, waterborne semi-gloss

1e 1.2 D83


For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; orFor powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or

Self priming - Resene Sonyx 101 D30, waterborne semi-gloss

Resene Sonyx 101 D30, waterborne semi-gloss


4th coat: Resene Multishield+ D54a, waterborne glaze (optional)

Exterior cementitious surfaces, waterborne satin

1e 1.3 D83



Resene Lumbersider D34, waterborne satin


4th coat: Resene Multishield+




http://www.resene.co.nz/archspec/datashts/d405_Concrete_Primer.pdf

http://www.resene.co.nz/archspec/datashts/d809_Limelock_Cure_&_Seal.pdf

http://www.resene.co.nz/archspec/datashts/d83_Cementitious_Surfaces.pdf

http://www.resene.co.nz/archspec/datashts/spec1_Cementitious.pdf




http://www.resene.co.nz/archspec/datashts/d54a_Multishield_Glaze.pdf

http://www.resene.co.nz/archspec/datashts/d30_Sonyx_101_Acrylic.pdf



http://www.resene.co.nz/archspec/datashts/d42_Sureseal_Sealer.pdf









http://www.resene.co.nz/archspec/datashts/d31_Hi-Glo_Acrylic.pdf











Description Resene One-Line Spec

Surface prep Surface prep 2nd coat 3rd coat

For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or

Self priming - Resene Lumbersider D34, waterborne satin

D54a, waterborne glaze (optional)

Exterior cementitious surfaces, waterborne mineral flat

20.e 1.5 SSP D83


For sound cementitious surfaces - Resene Aquapel D65; or

For powdery surface - Resene Sureseal D42, solvent-borne sealer

Resene Aquashield D601, waterborne mineral flat

Resene Aquashield D601, waterborne mineral flat

Exterior cementitious surfaces, solvent-borne gloss

1e 2.1 D83


For sound cementitious surfaces - Resene Concrete Primer D405,

waterborne primer; or


Resene Acrylic Undercoat D404, waterborne undercoat

Resene Super Gloss D32, solvent-borne gloss

Exterior timbers


http://www.resene.co.nz/archspec/datashts/d32_Super_Gloss_Enamel.pdf

http://www.resene.co.nz/archspec/datashts/d404_Acrylic_Undercoat.pdf









http://www.resene.co.nz/archspec/datashts/d601_AquaShield.pdf

http://www.resene.co.nz/archspec/datashts/d601_AquaShield.pdf


http://www.resene.co.nz/archspec/datashts/d65_Aquapel_Water_Repellent.pdf



http://www.resene.co.nz/archspec/datashts/spec20_Textured_Coatings.pdf









Surface prep 1st coat 2nd coat 3rd coat

Exterior timbers, waterborne gloss

2e 1.1 D82; and Resene TimberLock D48, solvent-borne

preserver/conditioner

For normal recommended system - Resene Quick Dry D45,

waterborne primer/undercoat; or

For timber that stains - Resene Wood Primer D40, solvent-borne primer; or

For hardboard only - Resene Sureseal D42, solvent-borne sealer



Exterior timbers, waterborne semi-gloss

2e 1.2 D82; and Resene TimberLock D48, solvent-borne preserver/conditioner

For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or


For hardboard only - Resene Sureseal D42, solvent-borne sealer



Exterior timbers, waterborne satin


For normal recommended system - Resene Quick Dry D45,

waterborne







http://www.resene.co.nz/archspec/datashts/d48_TimberLock.pdf

http://www.resene.co.nz/archspec/datashts/d82_Timber_Surfaces_Prep.pdf

http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf






http://www.resene.co.nz/archspec/datashts/d40_Wood_Primer.pdf




















primer/undercoat; or

For timber that stains - Resene Wood Primer D40, solvent-borne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or

Self priming - Resene Lumbersider D34, waterborne satin

Exterior timber joinery, waterborne gloss



For timber that stains - Resene Wood Primer D40, solvent-borne primer

Resene Enamacryl D309, waterborne gloss enamel


Exterior timber joinery, waterborne semi-gloss



For timber that stains - Resene Wood Primer D40, solvent-

Resene Lustacryl D310, waterborne semi-gloss enamel



http://www.resene.co.nz/archspec/datashts/d310_Lustacryl_WB_Enamel.pdf






http://www.resene.co.nz/archspec/datashts/spec3_Timber_Joinery.pdf

















borne primer

Exterior timbers, solvent-borne gloss


For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For hardboard only - Resene Sureseal D42, solvent-borne sealer



Exterior timber, stains and clear finishesDescription Resene One-

Line SpecSurface prep 1st coat 2nd coat 3rd coat

Exterior timbers, stains and clear finishes, waterborne stainThis system is not suitable for decks

2e 3.5 D82 Resene Waterborne Woodsman D57a, waterborne stain

Resene Waterborne Woodsman D57a, waterborne stain

Resene Waterborne Woodsman D57a, waterborne stain (after 3 months)

Exterior timbers, stains and clear finishes, solvent-borne flat. If used on decks this system may not meet the slip resistance requirements of the building code. SRG Grit can be added to improve performance.

2e 4.5 D82 Resene Woodsman D57, solvent-borne stain

Resene Woodsman D57, solvent-borne stain


Exterior timber joinery


http://www.resene.co.nz/archspec/datashts/d57_Woodsman_Oil_Stain.pdf






http://www.resene.co.nz/archspec/datashts/d57a_WB_Woodsman_Oil_Stain.pdf


















Exterior timber joinery, waterborne gloss






Exterior timber joinery, waterborne semi-gloss






Exterior timber joinery, solvent-borne gloss






Exterior timber decks, pergolas and fencesDescription Resene

One-Line Surface prep 1st coat 2nd coat 3rd coat






























Spec

Exterior timber decks, pergolas and fences, waterborne satin. If used on decks this system may not meet the slip resistance requirements of the building code. SRG Grit can be added to improve performance.


For normal recommended system - Resene Lumbersider D34, waterborne satin



Exterior timber decks, non-skid finish


Resene Quick Dry D45, waterborne primer/undercoat

Resene Non-Skid Deck & Path D313, non-skid finish

Resene Non-Skid Deck & Path D313, non-skid finish

Exterior timber, pergolas and fences, waterborne stain. This system is not suitable for decks.

4e 3.5 D82 Resene Waterborne Woodsman D57a, waterborne stain

Resene Waterborne Woodsman D57a, waterborne stain

Resene Waterborne Woodsman D57a, waterborne stain (after 3 months)

Exterior timber decks, pergolas and fences, solvent-borne stain. If used on decks this system may not meet the slip resistance requirements of the BCA.

4e 4.5 D82 Resene Woodsman D57, solvent-borne stain


Resene Woodsman D57, solvent-borne stain (after 3 months)

Exterior timber decks, pergolas and

4e 4.5 C D82 Resene Kwila Timber Stain D501, solvent-

Resene Kwila Timber Stain D501, solvent-

-


http://www.resene.co.nz/archspec/datashts/d501_Kwila_Timber_Stain.pdf



http://www.resene.co.nz/archspec/datashts/spec4_Timber_Decks_Fences.pdf



















http://www.resene.co.nz/archspec/datashts/d313_Non-Skid_Deck_&_Path.pdf

http://www.resene.co.nz/archspec/datashts/d313_Non-Skid_Deck_&_Path.pdf

















fences, solvent-borne stain. If used on decks this system may not meet the slip resistance requirements of the BCA.

borne stain borne stain

Exterior timber decks, pergolas and fences, solvent-borne stain. If used on decks this system may not meet the slip resistance requirements of the BCA.

4e 4.5 N D82 Resene Furniture and Decking Oil D503, solvent-borne oil

Resene Furniture and Decking Oil D503, solvent-borne oil

-

Exterior galvanized steel and zincalumeDescription Resene One-


Exterior galvanized steel and Zincalume, waterborne gloss

5e 1.1 D89 For new work - Resene Galvo-Prime D402, waterborne galvanized iron primer; or

For repaint - Resene Galvo One D41, solvent-borne galvanized iron primer 2 coats of primer strongly recommended for non-rain washed areas



Exterior galvanized steel and Zincalume, waterborne

5e 1.2 D89 For new work - Resene Galvo-Prime D402, waterborne

Resene Sonyx 101 D30, waterborne

Resene Sonyx 101 D30, waterborne




http://www.resene.co.nz/archspec/datashts/d402_Galvo-Prime_Primer.pdf

http://www.resene.co.nz/archspec/datashts/d89_Non-Ferrous_Metals.pdf

http://www.resene.co.nz/archspec/datashts/spec5_Steel_Galvanised_Ext.pdf






http://www.resene.co.nz/archspec/datashts/d41_Galvo_One_Primer.pdf







http://www.resene.co.nz/archspec/datashts/d503_Furniture_Decking_Oil.pdf

http://www.resene.co.nz/archspec/datashts/d503_Furniture_Decking_Oil.pdf








semi-gloss galvanized iron primer; or\For repaint - Resene Galvo One D41, solvent-borne galvanized iron primer 2 coats of primer strongly recommended for non-rain washed areas

semi-gloss semi-gloss

Exterior galvanized steel and Zincalume, waterborne satin

5e 1.3 D89 For new work - Resene Galvo-Prime D402, waterborne galvanized iron primer; or\For repaint - Resene Galvo One D41, solvent-borne galvanized iron primer 2 coats of primer strongly recommended for non-rain washed areas. System not suitable for roofs



Exterior galvanized steel and Zincalume, solvent-borne gloss system not suitable for roofs

5e 2.1 D89 Resene Galvo One D41, solvent-borne galvanized iron primer



Exterior cedarDescription Resene

One-Line Spec


Exterior cedar, waterborne gloss


Resene Wood Primer D40, solvent-borne primer


Resene Hi-Glo D31, waterborne gloss 4th coat: Resene Hi-Glo







http://www.resene.co.nz/archspec/datashts/spec8_Cedar_Exterior.pdf























D31, waterborne gloss (4th coat optional on weathered cedar)

Exterior cedar, waterborne semi-gloss




Resene Sonyx 101 D30, waterborne semi-gloss 4th coat: Resene Sonyx 101 D30, waterborne semi-gloss (4th coat optional on weathered cedar)

Exterior cedar, waterborne satin




Resene Lumbersider D34, waterborne satin 4th coat: Resene Lumbersider D34, waterborne satin (4th coat optional on weathered cedar)

Exterior cedar, solvent-borne gloss




Resene Super Gloss D32, solvent-borne gloss 4th coat: Resene Super Gloss D32, solvent-borne gloss

Exterior cedar, waterborne

8e 3.5 D82 Resene Waterborne

Resene Waterborne

Resene Waterborne

































stain Woodsman D57a, waterborne stain

Woodsman D57a, waterborne stain

Woodsman D57a, waterborne stain (after 3 months)

Exterior cedar, solvent-borne stain

8e 4.5 D82 For stained finish - Resene Woodsman D57, solvent-borne stain


Resene Woodsman D57, solvent-borne stain (after 3 months)

Exterior cedar, solvent-borne stain, kwila timber stain colour

8e 4.5 D82 Resene Kwila Timber Stain D501, solvent-borne stain

Resene Kwila Timber Stain D501, solvent-borne stain

-

Concrete waterproofing membranesDescription Resene One-


Barrier membranes, waterborne semi-gloss

17e 1.2T D83 For thin plaster - Resene Limelock D809, waterborne cure/seal


For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene Thixalon 5 D63, waterborne semi-gloss

Resene Thixalon 5 D63, waterborne semi-gloss

Resene Thixalon 5 D63, waterborne semi-gloss 4th coat: Resene Multishield+ D54a, waterborne glaze (optional)

Waterproofing 17e 1.2F D83 For sound Resene Resene



http://www.resene.co.nz/archspec/datashts/spec17_Waterproofing_Memb.pdf



http://www.resene.co.nz/archspec/datashts/d63_Thixalon5_Waterproofing.pdf

























membranes, waterborne semi-gloss. A minimum film build of 500 microns is required.


cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or

For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene Flexicover E D64, waterborne semi-gloss

Flexicover E D64, waterborne semi-gloss

Flexicover E D64, waterborne semi-gloss 4th coat: Resene Lumbersider D34, waterborne satin (optional)

Waterproofing membranes, waterborne low sheen

17e 1.4 D83For thin plaster - Resene Limelock D809, waterborne cure/seal


For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene X-200 D62, waterborne low sheen

Resene X-200 D62, waterborne low sheen

Resene X-200 D62, waterborne low sheen 4th coat: Resene Multishield+ D54a, waterborne glaze (optional)

Exterior metallic finishesDescription Resene One-


Exterior waterborne metallic

25e 1.3/5 D83 Resene Quick Dry D45, waterborne

Resene Lumbersider D34,

3rd/4th coat: Resene Enamacryl





http://www.resene.co.nz/archspec/datashts/spec25_Special_Effects.pdf





http://www.resene.co.nz/archspec/datashts/d62_X-200_Waterproofing.pdf











http://www.resene.co.nz/archspec/datashts/d64_Flexicover_E_Membrane.pdf












primer/undercoat Waterborne low sheen must be applied where a barrier coat is needed. 2 full coats of Resene X-200 D62

waterborne satin

Metallic D309a, waterborne metallic 5th coat: Resene Multishield+ D54a, waterborne glaze (optional)

Exterior waterborne pearlescent

25e 1.3/5 P D83 Resene Quick Dry D45, waterborne primer/sealer


3rd coat: Resene Lumbersider D34, waterborne satin

4th coat: Resene Pearl Shimmer D312, waterborne pearlescent

5th coat: Resene Multishield+ D54a, waterborne glaze (optional)

Exterior metallic finish on concrete floor, Two-pack

25e 2.3/5 D83 Resene Armourcote 510 RA40, high solids epoxy

Resene Imperite IF 503 RA81, solvent-borne metallic

Resene Uracryl 400 Series Clear, acrylic urethane

4.3 INTERIOR PAINTING SCHEDULES

Paint system schedulesPaint system: To the INTERIOR PAINT SYSTEM clause identified by the Resene Specification Number.

Interior finishes scheduleRoom name Code Substrate Resene Spec

NumberColour


http://www.resene.co.nz/archspec/datashts/ra81_Imperite_I_F_503_Gloss.pdf

http://www.resene.co.nz/archspec/datashts/ra40_Armourcote_510_Epoxy.pdf







http://www.resene.co.nz/archspec/datashts/d312_Pearl_Shimmer_Glaze.pdf










http://www.resene.co.nz/archspec/datashts/d309a_Enamacryl_Metallic.pdf



Room name Code Substrate Resene Spec Number

Colour

4.4 INTERIOR PAINT SYSTEMS

Resene interior paint systemsInterior paint systems: Supply the listed Resene systems for the following substrates.

Interior cementitious surfacesDescription Resene One-


Interior cementitious surfaces, waterborne gloss

1i 1.1 D83




Resene Enamacryl D309, waterborne gloss

Resene Enamacryl D309, waterborne gloss

Interior cementitious surfaces, waterborne semi-gloss

1i 1.2 D83For thin plaster - Resene Limelock D809, waterborne cure/seal


For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene Lustacryl D310, waterborne semi-gloss




























enamel

Interior cementitious surfaces, waterborne satin

1i 1.3 D83



For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene Lumbersider D34, waterborne satin



Interior cementitious surfaces, waterborne low sheen

1i 1.4 ZS D83



For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene Zylone Sheen or Resene Zylone Sheen VOC

Free D302, waterborne low

Resene Zylone Sheen or Resene Zylone Sheen VOC

Free D302, waterborne low sheen

Resene Zylone Sheen or Resene Zylone Sheen VOC

Free D302, waterborne low sheen



























sheen

Interior cementitious surfaces, waterborne low sheen

1i 1.4 SC D83



For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene SpaceCote Low Sheen D311, waterborne low sheen enamel

Resene SpaceCote Low Sheen D311, waterborne low sheen enamel


Interior cementitious surfaces, waterborne flat

1i 1.5 D83



For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene Zylone 20 D37, waterborne flat

Resene Zylone 20 D37, waterborne flat


Interior cementitious surfaces,

1i 1.5 SC D83 For sound cementitious surfaces -

Resene SpaceCote Flat D314,

Resene SpaceCote Flat D314,


http://www.resene.co.nz/archspec/datashts/d314_SpaceCote_Flat.pdf







http://www.resene.co.nz/archspec/datashts/d37_Zylone_20_Flat_Acrylic.pdf











http://www.resene.co.nz/archspec/datashts/d311_SpaceCote_Low_Sheen.pdf














waterborne flat enamel


Resene Concrete Primer D405, waterborne primer; or

For powdery surfaces - Resene Sureseal D42, solvent-borne sealer; or Self priming - Resene SpaceCote Flat D314, waterborne flat enamel



Interior cementitious surfaces, solvent-borne gloss

1i 2.1 D83






Interior cementitious surfaces, solvent-borne semi-gloss

1i 2.2 D83



For powdery surfaces - Resene

Resene Lusta-Glo D33, solvent-borne semi-gloss



http://www.resene.co.nz/archspec/datashts/d33_Lusta-Glo_Enamel.pdf


























Sureseal D42, solvent-borne sealer

Interior timberDescription Resene

One-Line Spec


Interior timber, waterborne gloss

2i 1.1 D82; and Resene TimberLock D48, solvent-borne preserver/conditioner



For hardboard only - Resene Sureseal D42, solvent-borne sealer; or

For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer

Resene Enamacryl D309, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat


Interior timber, waterborne semi-gloss



For timber that

Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404,


























stains - Resene Wood Primer D40, solvent-borne primer; or

For hardboard only - Resene Sureseal D42, solventborne sealer; or


waterborne undercoat

Interior timber, waterborne satin





For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer; or Self priming - Resene




















Lumbersider D34, waterborne satin

Interior timber, waterborne low sheen

2i 1.4 ZS D82; and Resene TimberLock D48, solvent-borne preserver/conditioner



For hardboard only - Resene Sureseal D42, solventborne sealer; or

For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer; or Self priming - Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen

Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen


Interior timber, waterborne satin

2i 1.4 SC D82; and Resene TimberLock D48, solvent-borne preserver/conditioner





























For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer; or Self priming - Resene SpaceCote Low Sheen D311, waterborne low sheen enamel

Interior timber, waterborne flat





For painting over varnish - Resene




















Waterborne Smooth Surface Sealer D47a, waterborne sealer; or Self priming - Resene Zylone 20 D37, waterborne flat

Interior timber, waterborne flat enamel

2i 1.5 SC D82; and Resene TimberLock D48, solvent-borne preserver/conditioner




For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer; or Self priming - Resene SpaceCote Flat D314, waterborne flat enamel

Resene SpaceCote Flat D314, waterborne flat enamel


Interior timber, solvent-borne gloss

2i 2.1 D82; and Resene TimberLock D48, solvent-borne preserver/conditione

For normal recommended system - Resene Quick Dry

Resene Acrylic Undercoat D404, waterborne

Resene Super Gloss D32, solvent-borne
























r D45,waterborne primer/undercoat; or




undercoat gloss

Interior timber, solvent-borne semi-gloss





For painting over varnish - Resene Waterborne

Resene Lusta-Glo D33, solvent-borne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat




















Smooth Surface Sealer D47a, waterborne sealer

Interior timber stains and clear finishesDescription Resene One-

Line SpecSurface prep 1st coat 2nd coat 3rd/4th/5th

coat

Interior timber, stains and clear finishes, waterborne gloss

2i 3.1 D82 Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional)

Resene Aquaclear D59, waterborne gloss urethane


Interior timber, stains and clear finishes, waterborne semi-gloss


Resene Aquaclear D59, waterborne semi-gloss urethane


Interior timber, stains and clear finishes,

2i 3.3 D82 Stained finish - Resene Waterborne

Resene Aquaclear D59, waterborne

Resene Aquaclear D59, waterborne


http://www.resene.co.nz/archspec/datashts/d59_Aquaclear_Varnish.pdf









http://www.resene.co.nz/archspec/datashts/d50a_WB_Colorwood_Woodstain.pdf



















Surface prep 1st coat 2nd coat 3rd/4th/5th coat

waterborne satin

Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional)

satin urethane satin urethane

Interior timber, stains and clear finishes, solvent-borne gloss


Resene Poly-Flat D52, solvent-borne flat clear; or

For particleboard and fibre board - Resene Aquaclear D59, waterborne urethane

Resene Poly-Gloss D52, solvent-borne gloss clear

Interior timber, stains and clear finishes, heavy duty solvent-borne gloss

2i 4.1 D82 Heavy duty finish - Resene Polythane D53, solvent-borne gloss clear;

For particleboard and fibre board - Resene Particleboard Sealer D43, waterborne sealer

Resene Polythane D53, solvent-borne gloss clear


Interior timber, stains and clear finishes,

2i 4.3 D82 Stained finish - Resene Waterborne

Resene Poly-Flat D52, solvent-borne

Resene Poly-Satin D52, solvent-borne


http://www.resene.co.nz/archspec/datashts/d52_Qristal_Polyurethane.pdf



























solvent-borne satin

Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional)

flat clear; or


satin clear

Interior timber, stains and clear finishes, solvent-borne flat


Resene Poly-Flat D52, solvent-borne flat clear; or


Resene Poly-Flat D52, solvent-borne flat clear

Interior timber floors, stains and clear finishes dedicated section for floorsDescription Resene One-

Line SpecSurface prep 1st coat 2nd coat 3rd/4th/5th

coat

Interior timber, stains and clear finishes, waterborne gloss

2i 3.1 F D82 For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Aquaclear D59, waterborne





























gloss urethane

Interior timber, stains and clear finishes, waterborne semi-gloss

2i 3.2 F D82 For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Aquaclear D59, waterborne gloss urethane



Interior timber, stains and clear finishes, waterborne satin

2i 3.3 F D82 For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Aquaclear D59, waterborne gloss urethane

Resene Aquaclear D59, waterborne satin urethane

Resene Aquaclear D59, waterborne satin urethane

Interior timber, stains and clear finishes, solvent-borne gloss

2i 4.1 F D82 For heavy duty finish - Resene Polythane D53, solvent-borne gloss clear; or

For particle board and fibre board - Resene Particle Board Sealer D43, waterborne sealer



Interior timber, stains and clear finishes, solvent-borne satin

2i 4.3 F D82 For stained finish - Resene Waterborne Colorwood D50a,

Resene HD Poly-Satin D52, solvent-borne satin clear

Resene HD Poly-Satin D52, solvent-borne satin clear










http://www.resene.co.nz/archspec/datashts/d53_Polythane_Polyurethane.pdf


http://www.resene.co.nz/archspec/datashts/d43_Particle_Board_Sealer.pdf




























waterborne wood stain; or

For clear finish - Resene HD Poly-Satin D52, solvent-borne satin clear; or

For particle board and fibre board - Resene Aquaclear D59, waterborne urethane

Interior timber joineryDescription Resene

One-Line Spec


Interior timber joinery, waterborne gloss


For normal recommended system - Resene Quick Dry D45; waterborne primer/undercoat; or





Interior timber joinery, waterborne

3i 1.2 D82; and Resene TimberLock D48, solvent-borne

For normal recommended system - Resene

Resene Lustacryl D310,

Resene Lustacryl D310,























semi-gloss preserver/conditioner

Quick Dry D45; waterborne primer/undercoat; or



waterborne semi-gloss enamel

waterborne semi-gloss enamel

Interior timber joinery, waterborne low sheen







Interior timber joinery, waterborne flat


For normal recommended system - Resene Quick Dry D45; waterborne primer/undercoat











http://www.resene.com.au/archspec/datasheets/d311_SpaceCote_Low_Sheen.pdf














; or



Interior timber joinery, solvent-borne gloss







Interior timber joinery, solvent-borne semi-gloss



For timber that

























stains - Resene Wood Primer D40, solvent-borne primer; or


Interior timber joinery, clear waterborne gloss

3i 3.1 D82 For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or

For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional)



Interior timber joinery, clear waterborne semi-gloss





Interior timber 3i 3.3 D82 For stained finish Resene Resene







http://www.resene.com.au/archspec/datasheets/d50a_Colorwood.pdf



















joinery, clear waterborne satin

- Resene Waterborne Colorwood D50a, waterborne wood stain; orFor clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional)

Aquaclear D59, waterborne satin urethane

Aquaclear D59, waterborne satin urethane

(5th coat optional)

Interior timber joinery, clear solvent-borne gloss



Resene Waterborne Colorwood D50a, waterborne wood stain

3rd coat: Resene Poly-Flat D52

4th/5th coat: Resene Poly-Gloss D52, solvent-borne gloss clear

Interior timber joinery, clear heavy duty solvent-borne gloss

3i 4.1 D82 For heavy duty finish - Resene Polythane D53, solvent-borne gloss clear; or

For particle board and fibre board - Resene Particle Board Sealer D43, waterborne sealer



No 5th coat required.

Interior timber joinery, clear

3i 4.1 D82 For stained finish - Resene

Resene Poly-Flat D52,

Resene Poly-Satin D52,










http://www.resene.co.nz/archspec/datashts/d43_Particle_Board_Sealer.pdf























solvent-borne satin

Waterborne Colorwood D50a, waterborne wood stain; or


solvent-borne flat clear

solvent-borne satin clear

No 5th coat required.

Interior paper faced plaster/solid plaster/fibrous plasterDescription Resene One-

Line SpecSurface prep 1st coat 2nd coat 3rd/4th coat

Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne gloss

15i 1.1 Level 5 D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep

(if reqd): For wet area, stained, porous or powdery areas - Resene Sureseal D42; solvent-borne sealer

For new wet areas - Resene Waterborne Smooth Surface Sealer D47a



15i 1.11 Level 5 (3 in 1 system)

D84; D85; D87; Resene Broadwall 3 in 1 D810, waterborne prep


For new wet areas - Resene Waterborne







http://www.resene.com.au/archspec/datasheets/d810_Broadwall_3in1.pdf

http://www.resene.co.nz/archspec/datashts/d87_Repainting.pdf

http://www.resene.co.nz/archspec/datashts/d85_Gypsum_Plaster_Prep.pdf

http://www.resene.co.nz/archspec/datashts/d84_Paperfaced_Plaster.pdf

http://www.resene.co.nz/archspec/datashts/spec15_Plaster_Interior.pdf


















Surface prep 1st coat 2nd coat 3rd/4th coat

Smooth Surface Sealer D47a

15i 1.1 Level 4 Resene Broadwall Waterborne Wallboard Sealer D403



Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne semi-gloss















Interior paperfaced

15i 1.3 Level 5 D84; D85; D87; Resene

(if reqd): For wet area,

Resene Lumbersider

Resene Lumbersider










































plaster/solid plaster/fibrous plaster, waterborne satin

Broadwall Surface Prep & Seal D807, waterborne prep

stained, porous or powdery areas - Resene Sureseal D42; solvent-borne sealer

D34, waterborne satin

D34, waterborne satin









Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne low sheen

15i 1.4 ZS Level 5

D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep

(if reqd): For wet area, stained, porous or powdery areas - Resene Sureseal D42; solventborne sealer



15i 1.41 ZS

Level 5 ( 3 in 1 system)

















































15i 1.4 ZS Level 4

Resene Broadwall Waterborne Wallboard Sealer D403



Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne low sheen enamel

15i 1.4 SC Level 5


(if reqd): For wet area, stained, porous or powdery areas - Resene Sureseal D42; solventborne sealer; or

For new wet areas - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer



15i 1.41 SC

Level 5 (3 in 1 System)

D84; D85; D87; Resene Broadwall 3 in 1 System D810, waterborne prep

(if reqd): For wet area, stained, porous or powdery areas - Resene Sureseal D42; solvent-borne sealer; or




15i 1.4 SC Level 4




Interior 15i 1.5 Level 5 D84; D85; D87; (if reqd): For Resene Zylone Resene Zylone











































paperfaced plaster/solid plaster/fibrous plaster, waterborne flat

Resene Broadwall Surface Prep & Seal D807, waterborne prep

wet area, stained, porous or powdery areas - Resene Sureseal D42; solvent-borne sealer

20 D37, waterborne flat

20 D37, waterborne flat

15i 1.51 Level 5 (3 in 1 System)

D84; D85; D87; Resene Broadwall 3 in 1 system D807, waterborne prep







Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne flat - ceiling

15i 1.5 Level 5 Ceiling



Resene Ceiling Paint D305, waterborne flat


15i 1.51

Level 5 Ceiling (3 in 1 system)


(if reqd): For wet area, stained, porous or powdery areas - Resene Sureseal

D42; solvent-borne sealer



15i 1.5 L 4 Ceiling

Resene Broadwall Waterborne Wallboard



















































Sealer D403

Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne flat

15i 1.5 SC Level 5


(if reqd): For wet area, stained, porous or powdery area, Resene Sureseal

D42, solvent-borne sealer; or

For new wet area, Resene Waterborne Smooth Surface Sealer D47a



15i 1.51 SC

Level 5 (3 in 1 System)


(if reqd): For wet area, stained, porous or powdery area, Resene Sureseal D42, solvent-borne sealer; or

For new wet area, Resene Waterborne Smooth Surface Sealer D47a



15i 1.5 SC Level 4




Interior paperfaced plaster/solid plaster/fibrous plaster, solvent-borne gloss


Resene Sureseal D42, solvent-borne sealer; or

For new wet areas, Resene Waterborne Smooth Surface















































Sealer D47a

15i 1.21 L 5 (3 in 1 system)



For new wet areas, Resene Waterborne Smooth Surface Sealer D47a





Resene Super Gloss D32, solventborne gloss

Interior paperfaced plaster/solid plaster/fibrous plaster, solvent-borne semi-gloss












15i 2.2 Level 4 Broadwall Waterborne Wallboard Sealer D403













































Interior metallic finishesDescription Resene One-

Line SpecSurface prep 1st coat 2nd coat 3rd/4th coat

Interior metallic finishes, waterborne metallic finish on Anaglypta, Scandatex, etc

25i 1.3/5 D84; D85 Resene Broadwall Waterborne Wallboard Sealer D403


Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional)

Interior metallic finishes, waterborne metallic finish on paperfaced plasterboard

25i 1.3/51 D84; D85 Resene Broadwall Surface Prep and Seal D807, waterborne surfacer/sealer or Resene Broadwall 3 in 1 Sealer D810, waterborne surfacer/sealer



Interior metallic finishes, waterborne metallic finish on MDF joinery/doors

25i 1.3/52 D82 Resene Quick Dry D45, waterborne primer/undercoat



Interior metallic finishes, waterborne pearlescent finish on interior surfaces

25i 1.3/52 P D82 for MDF; D84

D85

Normal recommended system: Resene Quick Dry D45, waterborne primer/undercoat; or For paperfaced plasterboard Resene Broadwall


3rd coat: Resene Lumbersider D34, waterborne satin 4th coat: Resene Pearl Shimmer D312, waterborne pearlescent 5th coat: Resene


http://www.resene.co.nz/archspec/datashts/d312_Pearl_Shimmer_Glaze.pdf






































Surface Prep and Seal D807, waterborne surfacer/sealer or Resene Broadwall 3 in 1 Sealer D810, waterborne surfacer/sealer

Aquaclear D59, waterborne gloss urethane (optional)

Interior metallic finishes, solventborne metallic finish on concrete floor

25i 2.3/5 D83 Resene Armourcote 510 RA40, high solids epoxy

Resene Imperite I.F. 503 RA81, solvent-borne metallic

Resene Uracryl 400 Series Clear, solvent-borne clear

Interior metallic finishes, solventborne metallic finish on MDF Joinery/doors

25i 2.3/51 D82 Refer Resene Paints Ltd

Resene Imperite I.F. 503 RA81, solvent-borne metallic

Resene Imperite I.F. 502 Clear RA82, semi-gloss clear


http://www.resene.co.nz/archspec/datashts/ra82_Imperite_I_F_502_Clear.pdf

http://www.resene.co.nz/archspec/datashts/ra81_Imperite_I_F_503_Gloss.pdf












0671p resene painting - web view0671p resene painting. branded worksection. this branded worksection...

Documents