01-installation and commissioning the rtn 900 v1r2 hybrid microwave-20091220-a
DESCRIPTION
Comissionamento HuaweiTRANSCRIPT
www.huawei.com
Huawei Confidential
Security Level: 23/4/18
英文标题 :40-47pt
副标题 :26-30pt
字体颜色 : 反白内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文标题 :35-47pt
字体 : 黑体 副标题 :24-28pt
字体颜色 : 反白字体 : 细黑体
Installing and Commissioning RTN 900
V100R200 Hybrid Microwave
英文目录标题 :35-40pt
颜色 : R153 G0 B0
内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文目录标题 :35-40pt
颜色 : R153 G0 B0
字体 : 黑体
英文目录正文 :28-30pt
子目录 (2-5 级 ) :20-30pt
颜色 : 黑色内部使用字体 :
FrutigerNext LT Regular
外部使用字体 : Arial
中文目录正文 :28-30pt
子目录 (2-5 级 ):20-30pt
颜色 : 黑色字体 : 细黑体
Contents
• Key Points
• Hardware Installation
• Equipment CommissioningEquipment Commissioning
• DCN CommissioningDCN Commissioning
• AcceptanceAcceptance
• Other SpecificationsOther Specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 3Huawei Confidential
Key PointsCaution Cause Requirement
1 Properly handle the IF board
and SCC power switches.
The field personnel do not know how
to operate the power switches. As a
result, a large number of boards on
the existing network are damaged.
This point must be imparted
to every field engineer,
especially the personnel of
the partners.
2 Do not reseat IF cables
when the power is on.
The ODU and IF board are damaged
by the reseating of IF cables when
the power is on.
This point must be imparted
to every field engineer,
especially the personnel of
the partners.
3 Do not tear up the ODU seal
or remove the ODU cover.
If the seal of the ODU is torn up or
the cover of the ODU is removed, the
vendor will refuse to provide warranty
services.
This point must be imparted
to every field engineer,
especially the personnel of
the partners.
4 Do not damage equipment
with improper operations.
If the damage is caused by artificial
factors, the vendor will refuse to
provide warranty services.
This point must be imparted
to every field engineer,
especially the personnel of
the partners.
HUAWEI TECHNOLOGIES CO., LTD. Page 4Huawei Confidential
Key Points
Properly handle the IF board and SCC power switches.
These boards are damaged due to improper operations of the personnel. Note: So many boards are found damaged in only one project!
① Train microwave partners for standardized operations according to projects.
② Hand out related training materials to every partner and every engineering team.
③ Provide special trainings for the partners with serious problems.
④ Provide effective trainings to all new partners.
HUAWEI TECHNOLOGIES CO., LTD. Page 5Huawei Confidential
Key Points
Do not reseat IF cables when the power is on.
Ensure the power is off before reseating IF cables or IF boards.
Pull IF cables out of the IF board, IF jumper, or ODU or plug into them after the power is off.
IF boards should also be reseated after the power is off.
Be careful in the use of a multimeter for testing the IF output voltage to avoid short circuits.
① Train microwave partners for standardized operations according to projects.
② Hand out related training materials to every partner and every engineering team.
③ Provide special trainings for the partners with serious problems.
④ Provide effective trainings to all new partners.
HUAWEI TECHNOLOGIES CO., LTD. Page 6Huawei Confidential
Key Points
Do not reseat IF cables when the power is on.
Power off the IF board before reseating IF cables.
Reseating IF cables when the power is on tends to cause a short circuit between the -48V power supply and the GND, which will blow out the protection tube.
The picture shows the short circuit.
① Train microwave partners for standardized operations according to projects.
② Hand out related training materials to every partner and every engineering team.
③ Provide special trainings for the partners with serious problems.
④ Provide effective trainings to all new partners.
HUAWEI TECHNOLOGIES CO., LTD. Page 7Huawei Confidential
Key Points
Do not tear up the ODU seal or remove the ODU cover.
If the seal of the ODU is torn up or the cover of the ODU is removed without permission, the vendor will refuse to provide warranty services.
The seal of the ODU shall not be torn up.
The ODU cover shall not be removed without permission.
① Train microwave partners for standardized operations according to projects.
② Hand out related training materials to every partner and every engineering team.
③ Provide special trainings for the partners with serious problems.
④ Provide effective trainings to all new partners.
HUAWEI TECHNOLOGIES CO., LTD. Page 8Huawei Confidential
Key Points
Do not damage equipment with improper operations.
If the damage is caused by artificial factors, the vendor will refuse to provide warranty services.
Handle ODUs with care.
Hoist and install ODUs with caution to avoid collision with the tower.
If the damage is caused by artificial factors, the vendor will refuse to provide warranty services.
The ODUs damaged during engineering operations must be returned as soon as possible. The vendor shall not provide warranty services after the warranty expires.
① Train microwave partners for standardized operations according to projects.
② Hand out related training materials to every partner and every engineering team.
③ Provide special trainings for the partners with serious problems.
④ Provide effective trainings to all new partners.
英文目录标题 :35-40pt
颜色 : R153 G0 B0
内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文目录标题 :35-40pt
颜色 : R153 G0 B0
字体 : 黑体
英文目录正文 :28-30pt
子目录 (2-5 级 ) :20-30pt
颜色 : 黑色内部使用字体 :
FrutigerNext LT Regular
外部使用字体 : Arial
中文目录正文 :28-30pt
子目录 (2-5 级 ):20-30pt
颜色 : 黑色字体 : 细黑体
Contents
• Key Points
• Hardware Installation
• Equipment CommissioningEquipment Commissioning
• DCN CommissioningDCN Commissioning
• AcceptanceAcceptance
• Other SpecificationsOther Specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 10Huawei Confidential
Installation of RTN 900 V1R2 Hybrid Microwave Hardware
Scenario Note Key Points
1 Installation of
ODUs
The operation is the same as that of the traditional microwave.
The Standardized Operating Process (SOP) is implemented based on the existing process. Courseware for partners .3D animation.
2 Installation of
IDUs
The operation is the same as that of the RTN 900 V1R1.
HUAWEI TECHNOLOGIES CO., LTD. Page 11Huawei Confidential
Installation of IDUs
Requirements for the input power of the IDU
RTN 910 RTN 950
Rated Voltage –48V/–60V –48V/–60V
Voltage Range –38.4V ~– 72V –38.4V ~– 72V
Number of Input Power Supplies
2 2
Recommended Fuse Capacity
10A 20A
英文目录标题 :35-40pt
颜色 : R153 G0 B0
内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文目录标题 :35-40pt
颜色 : R153 G0 B0
字体 : 黑体
英文目录正文 :28-30pt
子目录 (2-5 级 ) :20-30pt
颜色 : 黑色内部使用字体 :
FrutigerNext LT Regular
外部使用字体 : Arial
中文目录正文 :28-30pt
子目录 (2-5 级 ):20-30pt
颜色 : 黑色字体 : 细黑体
Contents
• Key Points
• Hardware Installation
• Equipment Commissioning
• DCN CommissioningDCN Commissioning
• AcceptanceAcceptance
• Other SpecificationsOther Specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 13Huawei Confidential
Commissioning – Strategies
BTS
IDU IDU
Third-party service channel or direct connection
B A
BSCMSC
Microwave NMS
Means for supporting the partner to complete the construction of BTSs independently: •WEBLCT•Handheld terminal•Remote access in wireless mode•SOP
Means for remote access: • Downloading the script files for remote
access in wireless mode• Centralized NMS (including 2M and
shared 2M)
Service configuration tools•U2000•U2000 LCT
Remote commissioning is recommended.
HUAWEI TECHNOLOGIES CO., LTD. Page 14Huawei Confidential
Equipment Commissioning – Strategies
RTN 900
Service configuration
System commissioning
Hardware installation
Antenna alignment
Hardware installation
Equipment power-on
RF configuration
Antenna alignment
Complete the
station work
Hardware personnel
Software commissioning engineers
Central Telecommunications Room
Station work
Equipment commissioning
It is recommended that the partners complete the station work independently.
HUAWEI TECHNOLOGIES CO., LTD. Page 15Huawei Confidential
Equipment Commissioning – Key Points Methods for commissioning the hybrid microwave are described as
follows:
The AM function of the hybrid microwave should be disabled before the
antennas are aligned.
The antennas should be aligned in low modulation mode provided by
network planning.
The received signal level (RSL) value must be within the scope as
required. The AM function of the hybrid microwave must be enabled after
the antennas are aligned.
Note: During equipment commissioning, perform operations as required. Otherwise, the boards may be damaged and you have to enter the station to replace the damaged boards!
HUAWEI TECHNOLOGIES CO., LTD. Page 16Huawei Confidential
Equipment Commissioning• Power On
There is no power switch on the RTN 900 IDU cabinet, so that, it is
important to test the input voltage value.
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 17Huawei Confidential
Equipment Commissioning Power on equipment and IF
boards• RTN 950
• RTN 910
1 2 3
The switches must be pulled out first and then turned to the right. Forcible pulling is prohibited!
Power on the corresponding power distribution box first. Power on the ODUs on the IF board (including active and standby ODUs). Note: The switches must be first pulled out and then turned.
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 18Huawei Confidential
Equipment Commissioning• Connect Laptop with RTN 900
ETH-OAM
WEBLCT
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 19Huawei Confidential
Equipment Commissioning Login U2000 Web
LCT
password : T2000
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 20Huawei Confidential
Equipment Commissioning Creat NE
①
②
③
④
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 21Huawei Confidential
Equipment Commissioning Configure NE ID/ NE Name
Configure NE names.
Change NE IDs. The IDs in one network must be unique.
③
②
①
④
⑤
⑥
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 22Huawei Confidential
Equipment Commissioning Add boards.
③
②
①
④
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 23Huawei Confidential
Equipment Commissioning Create the IF 1+1 protection group (this step can be omitted for the 1+0 mode).
③
②
①
④
Slot 1 and Slot 2 constitute a protection group with Slot 1 as the recommended working slot.
Slot 3 and Slot 5 constitute a protection group with Slot 3 as the recommended working slot.
Slot 4 and Slot 6 constitute a protection group with Slot 4 as the recommended working slot.
③
②
①
④
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 24Huawei Confidential
Equipment Commissioning Configure Link
②
① ③
④
⑤⑥
⑦See Next Page
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 25Huawei Confidential
Equipment Commissioning
Confirm that the AM function is disable .the default value is disable.
Configure Hybrid/AM——set IF channel band and confirm that the AM function is disabled.
Set the channel space and modulation
accroding to the design document.
Input the E1 number of the Hybrid
microwave frame. The E1 number should
be the same as the design document. The number of E1 should be the same in
one hop.
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 26Huawei Confidential
Equipment Commissioning Align the antennas – query the receive power.
③
②
①
④
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
HUAWEI TECHNOLOGIES CO., LTD. Page 27Huawei Confidential
Equipment Commissioning Enable the AM function.
After the AM function is enabled, set IF Channel Band, Modulation Mode of the Assured AM Capacity, and Modulation Mode of the Full AM Capacity according to networking planning.
③
②
①
It is zero when E1 does not exist.
⑥④ ⑤ ⑦
⑧
Power on equipment
Basic configuration
Confirm that the AM function is disabled
Align antennas
Enable the AM function
英文目录标题 :35-40pt
颜色 : R153 G0 B0
内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文目录标题 :35-40pt
颜色 : R153 G0 B0
字体 : 黑体
英文目录正文 :28-30pt
子目录 (2-5 级 ) :20-30pt
颜色 : 黑色内部使用字体 :
FrutigerNext LT Regular
外部使用字体 : Arial
中文目录正文 :28-30pt
子目录 (2-5 级 ):20-30pt
颜色 : 黑色字体 : 细黑体
Contents
• Key Points
• Hardware Installation
• Equipment Commissioning
• DCN CommissioningDCN Commissioning
• Acceptance
• Other Specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 29Huawei Confidential
DCN Commissioning – Extended ECC Communicate NMS information through the extended
ECC.For one telecom room, multiple RTN600s can interwork through the extended ECC. This work must be made clear to partners in advance.
NMS
HUAWEI TECHNOLOGIES CO., LTD. Page 30Huawei Confidential
DCN Commissioning – Solution Introduction Through third-party networks
Solution Description Advantage Disadvantage Priority
Through service
channels provided
by the customer
The customer provides the Ethernet or E1 (or N x 64 K)
channels, and NMS information of Huawei is directly
connected to the third-party Ethernet port as common
services or connected to E1 channels through the protocol
converter/clock port.
The interface of Huawei is
simple, involving no
cooperation with third-party
equipment.
The service channels of the
customer are occupied.
1
Transparent
transmission
through
synchronous
ports or
asynchronous
ports
The third-party equipment is required to provide the
synchronous or asynchronous data ports. Then, information
is transmitted transparently through the third-party
microwave equipment. Finally, information is converted back
to Ethernet NMS information through the protocol converter.
The NMS can also be connected to the third-party
equipment directly.
Service channels are not
occupied.
1. Special connectors need
to be prepared. 2. The
cooperation of the third party
is required, which is very
risky.
2
Through the IP
over DCC
protocol
The NEs of the third-party equipment are required to support
IP and NMS ports. NMS information is transmitted in IP
sharing mode.
Service channels are not
occupied.
1. It is hard to configure. 2.
The cooperation of the third
party is required, which is
very risky.
3
Through the OSI
protocol
The NEs of the third-party equipment are required to support
OSI (TP4) and NMS network ports. NMS information is
transmitted in OSI sharing mode.
Service channels are not
occupied.
1. It is harder to configure
this solution than the IP
solution. 2. The cooperation
of the third party is required,
which is very risky.
4
英文目录标题 :35-40pt
颜色 : R153 G0 B0
内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文目录标题 :35-40pt
颜色 : R153 G0 B0
字体 : 黑体
英文目录正文 :28-30pt
子目录 (2-5 级 ) :20-30pt
颜色 : 黑色内部使用字体 :
FrutigerNext LT Regular
外部使用字体 : Arial
中文目录正文 :28-30pt
子目录 (2-5 级 ):20-30pt
颜色 : 黑色字体 : 细黑体
Contents
• Key Points
• Hardware Installation
• Equipment Commissioning
• DCN Commissioning
• AcceptanceAcceptance
• Other SpecificationsOther Specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 32Huawei Confidential
Acceptance – Strategies1. The operations must be strictly compliant with the Acceptance Guide.
2. The acceptance consists of two parts, namely, Acceptance Items and Form
(Recommended) and Acceptance Items and Form (Optional).
3. It is recommended that the items to be tested should be selected only from the
Acceptance Items and Form (Recommended) and the items should be as few as
possible. If the customer has special requirements, a few items that can be tested
can be selected from the Acceptance Items and Form (Optional).
4. Before the acceptance, acceptance items and operation instructions that
correspond to these items should be printed based on the selected items,
combined into a manual, and submitted to the customer. The manual submitted to
the customer cannot consist of items not to be tested and corresponding test
instructions. It is prohibited to submit the unedited Acceptance Guide to users.
5. The items selected from the Acceptance Items and Form (Optional) need to be
quoted and charged separately.
6. Recommend remote acceptance to customers. It is recommended that the
percentage of items subject to on-site acceptance be 5% - 10%.
HUAWEI TECHNOLOGIES CO., LTD. Page 33Huawei Confidential
Acceptance – Online Test Methods of Ethernet Services Online test methods of Ethernet services: The ETH-OAM function is used for testing Ethernet services.
Prerequisite: Antenna alignment is completed. The RTN605 V100R300 or RTN620 V100R300 is configured with the EMS6.
1. Select the NE from the Object Tree in the NE Explorer of the NE1, and then choose Configuration > Ethernet OAM Management > Ethernet Service OAM Management
2. Select the MD, MA, and MEP that correspond to Port 1, click OAM. 3. Select Start LB.
The LB Test window is displayed. . 4. Select MP ID, and set the parameters in Test Node. 5. Click Start Test. 6. Check Detection Result. The LossRate in the Detection Result should be 0.
Procedure:
HUAWEI TECHNOLOGIES CO., LTD. Page 34Huawei Confidential
Acceptance – AM Test Method of testing the AM handover function: If the hybrid microwave is used for transmission, whether the
handover function is normal can be verified by testing the AM handover function.
Prerequisite: The antennas are aligned. The HYBRID/AM mode is configured.
① Disable the AM function.
② Enable 15-minute performance monitoring.
③ Query the performance: No FEC-BER-COR-ER, and only the low modulation mode is available.
④ Enable the AM function.
⑤ Query the performance: No FEC-BER-COR-ER exists. It can be found that the modulation modes is adjusted from low to high.
Procedure:
Notes: 1. The two ends of the link must be configured synchronously. 2. This method is not the same as the method of decreasing the optical power described in the Commissioning Guide. This is better. The Commissioning Guide will be modified later.
1 、
3 、
5 、
英文目录标题 :35-40pt
颜色 : R153 G0 B0
内部使用字体 :
FrutigerNext LT Medium
外部使用字体 : Arial
中文目录标题 :35-40pt
颜色 : R153 G0 B0
字体 : 黑体
英文目录正文 :28-30pt
子目录 (2-5 级 ) :20-30pt
颜色 : 黑色内部使用字体 :
FrutigerNext LT Regular
外部使用字体 : Arial
中文目录正文 :28-30pt
子目录 (2-5 级 ):20-30pt
颜色 : 黑色字体 : 细黑体
Contents
• Key Points
• Hardware Installation
• Equipment Commissioning
• DCN Commissioning
• Acceptance
• Other SpecificationsOther Specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 36Huawei Confidential
Reclaiming Licenses Strategies and requirements for microwave licenses
Due to the uncertainty of microwave network planning, delivery based on
BTSs is impossible. Therefore, under the microwave strategy, the Supply Chain
delivers the maximum number of licenses. The GTS is in charge of reclaiming
the frontline licenses. For projects delivered by customers, customer support
engineers should mark them clearly and the Supply Chain delivers the licenses
as planned.
During the engineering implementation or before preliminary acceptance,
GTS engineers reclaim licenses according to the actual license capacity in the
orders. GTS engineers download license files of the corresponding capacity
from the support website of Huawei, load them on the site or remotely through
the DC software, and then click the files to activate them.
HUAWEI TECHNOLOGIES CO., LTD. Page 37Huawei Confidential
Reclaiming Licenses Hybrid microwave license solution
This will be added in TR6!
HUAWEI TECHNOLOGIES CO., LTD. Page 38Huawei Confidential
Entry to CEAS In 2008, the Network Product Technical Service Dept issued the
Notice on Requirements for Entry of Information About RTN Microwave Customer Equipment to CEAS, clearly requiring that engineering information about RTN microwave should be entered to CEAS in a timely manner.
① The requirements and mode of entering homegrown products to CEAS should be the same
as those of other products. After a project is completed, related data needs to be entered in
CEAS. For entry criteria and operation methods, see the appendix to the Notice.
② For RTN microwave engineering projects completed in 2008 or earlier, all missing data
should be entered in CEAS in Q1 of 2009.
③ The network product manager of the technical service department at each representative
office is the first owner for entering and supplementing data about homegrown microwave
in CEAS. The product manager designates microwave engineers to complete the entry.
Currently, CEAS features low entry rate, low accuracy, and poor availability, which
seriously affects the follow-up implementation of services. To improve the data entry rate
of CEAS and enhance the timeliness and accuracy of CEAS data entry, the Network
Product Technical Service Dept reiterates that:
HUAWEI TECHNOLOGIES CO., LTD. Page 39Huawei Confidential
Entry to CEAS
Guide to entry of data about RTN900 V1000R200 in CEAS:
③
②
①
④ ⑤
HUAWEI TECHNOLOGIES CO., LTD. Page 40Huawei Confidential
Repair and Return of Damaged Boards Currently, there is a large number of OEM parts, especially ODUs, are not returned. This situation
seriously affects the analysis of fault causes and improvement of product quality of Huawei. If the damaged boards (especially ODUs) are not returned in a timely manner, the vendor may delay
the replenishment. The purchased microwave or ODU damaged within the warranty, especially at the engineering stage,
should be timely returned to vendors for repair, thus avoiding expensive maintenance costs caused by the repairs and returns beyond the warranty period.
Guide to Repair and Return of Overseas Purchased Microwave Parts (V1.0)
Guide to the Process of Handling the Faulty Purchased ODU (Applicable to the Countries Outside China)(V1.0)
Guide to the Process of Handling the Faulty Purchased ODU (Applicable to China)(V1.0) Criteria for Determining Whether an ODU Fault Is Caused by a Quality Defect of the ODUChecklist for the Description of the Faulty ODU.xls
Overseas Return and Repair Process for Spare Parts of Purchased ODUs Used in Self-Made Microwave Equipment
In March 2009, the process for handling damaged microwave ODUs was issued to the frontline for trial use. Representative offices and project teams need to return damaged parts and purchased parts as required.
HUAWEI TECHNOLOGIES CO., LTD. Page 41Huawei Confidential
Strategies for Spare Parts Key strategic points of homegrown microwave spare parts:
The number of microwave spare parts to be sold is 3% - 5% of that of microwave spare
parts to be installed. GTS engineers should control the sales of microwave spare parts
to customers effectively.
The HQ does not store spare parts for OEM microwave or purchased equipment such
as ODUs and antennas.
In principle, representative offices are not allowed to store microwave spare parts,
especially OEM equipment such as ODUs.
For managed services and replacement of spare parts, representative offices can store
a certain number of IDU and ODU spare parts according to the lowest requirement.
The HQ should review and approve the applications of representative offices for spare
parts in strict compliance with related service contracts and service SLAs.
The OEM microwave and OEM spare parts applied for by representative offices shall, in
principle, not be returned to the HQ (the method of handling the returned equipment or
spare parts is unavailable).
Thank youwww.huawei.com