0 linux dvr self-kit user’s guide. 1 the contents of this user’s manual shall not be reproduced...

1

Linux DVR Self-Kit

User’s Guide

2

The contents of this User’s Manual shall not be reproduced arbitrarily

without

prior approval.

The product of this User’s Manual may be modified without advance notice for the reasons of upgrading, etc.

The trademarks mentioned in this User’s Manual are registered trademark and unique trademark of each relevant company.

Please contact LeadTech Corporation for any unclear matters or errors to be corrected in the contents of this User’s Manual.

Copyright 2005ⓒLeadTech Corp. All Rights Reserved

Self-Kit Series, V2.86

Oct 2005

3

Matters to be Noted

Turn off the power of Linux DVR without fail before the installation.

The persons other than professional installer should not open the cover of the case of

this product at their own discretion.

When verifying internal part of this product for system upgrade or repair of trouble,

please ask to the place of purchase without fail.

When installing this product, maintain approximately 15cm of distance from other

nearby equipment.

Be careful not to apply impact or shaking when Linux DVR is moved or in operation.

Do not install at the place where there is strong magnetism or radio wave.

Surface of wall for smooth radiation of heat. Be attentive no conductive material is

put inside the cooling ventilation hole.

Please avoid installing at the places of high temperature such as nearby direct

sunlight or heater.

Please avoid installing at the places where are extremely cold or highly humid.

Before connecting the power, check the using power of AC100~240V 50/60Hz

without fail.

This unit is designed for indoor use. Operating ambient temperature must not range

beyond (0℃~+40℃)

4

Table Of Contents

Chapter 1. Self-Kit Introduction ……………………………………… I. Part of Self-Kit …………………………………………………………………………. 1. LDB-400MX …………………………………………………………………………. 2. LDB-800MX …………………………………………………………………………. 3. LDB-1600MX ………………………………………………………………………… 4. Option ………………………………………………………………………………… 5. Network Client Application (Eye-Linker) Install CD ………………………. II. Self-Kit Installation Guide …………………………………………………………. 1. Self-Kit Hardware Installation Guide …………………………………………. 2. How To Install The Initial Setup ………………………………………………….

Chapter 2. DVR Application User’s Guide …………………………… I. Usage of Remote Controller and Keyboard …………………………………….. 1. Function of Remote Controller and Keyboard ……………………………….. 2. By Remote Controller ………………………………………………………………. II. Surveillance Mode (Main GUI) ……………………………………………………. III. Setup Mode ………………………………………………………………………...... 1. General Setup ………………………………………………………………………… 2. Camera Setup ………………………………………………………………………… 3. Color Setup ………………………………………………………………………….... 4. Motion Area Setup …………………………………………………………………... 5. Schedule Setup …………………………………………………………………….... 6. Network Setup ……………………………………………………………………….. 7. Sensor Setup …………………………………………………………………………. 8. Alarm Setup …………………………………………………………………………... 9. PTZ Control Mode ……………………………………………………………………. 10. Backup Mode ………………………………………………………………………... 11. System Administration ……………………………………………………………. 12. Search Mode …………………………………………………………………………. IV. DVR Application Troubleshooting Guide ………………………………………..

Chapter 3. Eye-Linker User’s Guide …………………………………… I. Features of Eye-Linker …..…………………….……………………………………… II. Installation guide of Eye-Linker .………………………………………………….. 1. System spec. to be recommended for Eye-Linker .………………………….. 2. Installation steps for Eye-Linker ………………………………………………… 3. To run Eye-Linker …..……….………………………………………………………. III. User’s guide of Eye-Linker ..……………..………………………………………… IV. Eye-Linker Troubleshooting Guide ……….……………………………………….

45567899912

15161618192223252728293133343536394144

4748505050525367

5

Chapter 1.

Self-Kit Introduction

6

I. Part of Self-Kit

1. LDB-400MX

4CH Video Input Cable (BNC) * 1EA

¹ Flash Memory - 32MB(IDE 40Pin Compatible Type)

SM100M * 1EA

※ ¹ Flash Memory Embedded Linux OS, Device Driver, DVR Application Software Installed.

7

2. LDB-800MX


Flash Memory - 32MB(IDE 40Pin Compatible Type)

SM100M * 2EA

I. Part of Self-Kit

8

3. LDB-1600MX


Flash Memory - 32MB(IDE 40Pin Compatible Type)

SM400M * 1EA

I. Part of Self-Kit

9

4. OptionRemote Controller and Receiver

Remote Controller Receiver

4-1. Sensor Board

5. Network Client Application (Eye-Linker) Installation CD

DIO 400 Board

Eye-linker Installation CD

*Note*Eye-Link Installation CD including- Eye-Linker- Self-Kit User’s Guide

I. Part of Self-Kit

10

II. Self-Kit Installation

Guide1. Self-Kit Hardware Installation Guide LDB-400MX (30/30)

Self-Kit Installation Guide

LDB-400MX (30/30)

11


Guide

LDB-800MX (60/60)


LDB-800MX (60/60)

12


Guide

LDB-1600MX (120/120)


LDB-1600MX (120/120)

13

2. How To Install The Initial Setup


Guide

1) System booting after hooking HDD

※ This will be changed as per main board

2) HDD information in System Manager

[System Manager ]Normal viewing at initial setupHDD1 : Flash Memory (to be fixed)HDD2 : Primary Slave HDD2 : Secondary MasterHDD2 : Primary Slave HDD “Enter” after “Confirm” at initial setup (to start formatting HDD)

14


Guide

3) HDD formatting

[HDD Formatting ]

4) Running the DVR Application

To Run the DVR application after HDD Formatting.

“Enter” after “Confirm”

15


Guide

5) waiting

“Enter”

.dvdrDVR Application Program is working.

16

Chapter 2.

DVR Application User’s Guide

17

I. How To Use The Remote Controller And Keyboard

Remote Controller

POWERDVR Power ON/OFF (Currently not available)

1~16 Full Screen for each selected channel

FREEZE No applicable function

BACKUP DVR Backup Mode

REC

[Surveillance Mode]Full recording regardless of each setup data[Motion/Schedule Mode]Setup for motion and schedule

CANCELTo shift to high level menu at setup mode or to cancel the value in setup mode

ENTERTo shift to low level menu at setup mode or to apply the value at setup mode

To change the value at setup modeTo switch channel at the Surveillance Mode

To change the value at setup modeTo switch channel at the Surveillance Mode

To Move cursor at setup mode

To Move cursor at setup mode

REW at the Search Mode

FF at the Search Mode

Play Start / Play Pause (Toggle)

Stop playing

SEARCH Search Mode

SETUP Setup Mode

DIV[Surveillance Mode] 16–13–9–8–4–1-16 [Search Mode] 16-9-4-1-16

PTZ PAN/TILT Mode

1. Function of Remote Controller and Keyboard

18

*Note*All functions are the same as Remote controller.

Keyboard


19

2. By remote controller

Surveillance Mode

Setup Mode

First level of Setup

Second level of Setup

² Value of Setup

ENTER : to shift to low level menu

ENTER : to come out to high level menu after fixing the changing value CANCEL : to come out to high level menu

ENTER : to shift to low level menu

ENTER :to shift low level menu

SETUP : SETUP Mode

CANCEL : to shift to high level menu

CANCEL : to shift to high level menu then to save the change as per message.(YES, NO, CANCEL)

CANCEL : Surveillance Mode

※ ² Value of Setup

changing the value to use in the remote controller In the motion and schedule mode, REC key for changing the values


20

Surveillance Mode – live monitoring mode

II. Surveillance Mode (Main GUI)

[Surveillance Mode]

Current Mode : Surveillance Mode1

2 Monitoring area

Present time and date3

4 status of camera

Sensor status (working status is to be on by Yellow color )5

6 Alarm status (working status is to be on by Yellow color)

Number of user to be connected with Network (Eye-Linker)7

8 HDD status (current storage volume / maximum storage capacity)

Recording statusMotion Detection status

2 3

1

4

5

6

7

8

21

Window can be divided by “DIV” button at Surveillance Mode

[Monitoring area]

enlarge

[enlarged viewing]

CAM005

1

2

Monitoring area

Camera ID1

2 Camera status (I con)

Storage status

schedule status

PAN/TILT

Camera and sensor

Motion Detect storage status

TV OUT status

*Note*Each ICON shows the current settings

TIP #1. “DIV” function

[16]

[1]

[13]

[4]

[9]

[8]


22

[camera 1,2,3,4]

[camera 13,14,15,16]

[camera 5,6,7,8]

[camera 9,10,11,12 ]

TIP #2. , function

To record all data from all cameras regardless of setup data of each camera,Whenever want to be back to the setup data, push “REC” button one more time.

[ camera status in normal ] [on recording data from all camera]

TIP #3. “REC” function


23

III. Setup Mode

Setup Mode

1

2

1

2

Please Enter Password : Enter the password for setup (Default Password : 0000 “10”can be applied to “0”)SETUP MODE :

[Setup Mode-main window]

To shift the menu :

To choose the menu :

To shift to low level menu :

To shift to high level menu :

To change setup data :

To cancel setup data :

To apply setup data (no recording) :

TIP #4. Using remote controller in Setup Mode

ENTER

ENTER

CANCEL

REC

CANCEL

ENTER

24

1. General Setup

III. Setup Mode

1

2

3

4

5

6

7

8

[General Setup]

9

1

2

3

4

5

6

7

8

9

New Password : Only want to change password

Retype New Password

Channel Auto Switching : Switching camera channel automatically when the window is 13,9,8,4 division screen and full screen.

TV OUT : TV output for selected camera channel. Selected camera channels in TV are switching every selected seconds

Rebooting : Rebooting every selected days at selected hour (00~23) No rebooting when the value is Every 000 Days

Set Date : Changing the system date and time ( Warning! When time is newly set, all of the stored data will be deleted.)Water Mark : For the back up of JPG file

HDD : Warning of insufficient space of Hard disk

Video Type : Video Type (NTSC/PAL) and number of cameras

25

Set Date – Warning! When time is newly set, all of the stored data will be deletedVideo Type – NTSC / PAL

[To confirm saving the changes] [To Confirm rebooting]

TIP #5. Settings applied after rebooting in General Setup

III. Setup Mode

26

2. Camera Setup

III. Setup Mode

1

2

3

4

5

6

Camera

I D : ID of camera. Basic setup is set for ‘CAM+Camera No. (Max 8 characters)

PTZ Type / ID: Type of pan/tilt Camera and ID

Recording Status: Full Record / Do Not Record / Schedule

Motion Sensitivity : Sensitivity : 1 to 10, 10 is the most sensitive Post Recording : recording time after the motion is detected Display : Showing blue area in the Surveillance Mode when the motion is detected

1

2

3

4

5

6

7

8

9

Frame rate : Frame rate per sec

10

27

III. Setup Mode

7

8

9

Image Quality : Setting can be done from 1 to 5, and 5 is the best image qualityAlarm : Ring alarm at Surveillance mode when movement is detected. User can select one among 4 alarms.

Resolution : For NTSC: 320 x 240, 640 x 240 For PAL: 320 x 288, 640 x 288

10 Apply All : Applying to all the cameras with the same settings of current camera (ON/OFF)

TIP #6. Motion Sensitivity in Surveillance Mode

(Example) Sensitivity : 06 Post Recording : 03 sec Display : ON When the motion is detected, it will be recorded during 3 sec after the detection. It shows blue box when the motion is detected.

[Screen of Surveillance Mode]

It shows blue box when the motion is detected

TIP #7. Apply All (the same function in all other setup)

Applying to all the cameras with the same settings of current camera (ON/OFF) However, the settings are not changed before you save the changes.

Selecting ‘Yes’ means saving all the settings you have changed.

28

3. Color Setup

III. Setup Mode

1

2

3

4

5

6

1

2

3

4

5

6

Camera

BRIGHTNESS

SATURATION

HUE

CONTRAST

APPLY ALL : Applying to all the cameras with the same settings of current camera (ON/OFF)

29

4. Motion Area Setup

III. Setup Mode

1

2

3

4

Camera : to choose the camera for setting

Setup Motion Area : Example for motion area

Motion Area : to set up the motion area on the camera screen. – Default Value : to set up the full motion area (use the “REC” button and cursors for setting motion area)

Apply All : to apply the fixed setting to all cameras (ON/OFF)

1 2

3

4

Unselected Area

Unselected Area (with cursor)

Selected Area

Selected Area (with cursor)

[Motion Area Setup window]

30

5. Schedule Setup

III. Setup Mode

1 2

3

4

1

2

3

Camera : to choose the camera for setting

Setup Schedule : example for setting the schedule

Apply All : to apply the fixed setting to all cameras (ON/OFF)

Record

Motion Record

Do Not Record

[Schedule Setup 화면 ]

31

TIP #8. For Schedule and Motion detecting Recording

Setup Schedule and Motion detecting recording

1. Set “Recording Status” to “Schedule” in the Camera Setup2. Set “Record” or “Motion” of the selected camera in the Schedule Setup3. Set motion area of the selected camera in the Motion Area Setup

[1. Set “Recording Status” to “Schedule”]

III. Setup Mode

[2. Set schedule in the Schedule Setup]

[3. Set motion area in the Motion Area Setup]

if setting the schedule like the upper picture for camera 01 - every Sunday : No recording- every Monday : Always recording- every Tuesday: recording when motion is detected

32

6. Network Setup

III. Setup Mode

[Network Setup window]

1

2

3

4

5

Connection : to setup the network LAN / ADSL / DHCP

I P : IP Address

Net Mask / ADSL ID / Nothing : LAN – to setup Net Mask ADSL – to input ID password DHCP – nothing applicable.

Gateway / ADSL Password / Nothing :LAN – to setup Gateway ADSL – to input ID PasswordDHCP – nothing applicable

Port : For Network Client Application (Eye-Linker) – Default value : 5005

9

1

2

3

4

5

6

7

8

33

6

7

8

9

Concurrent User : Concurrent number of user for Network Client Application (Eye-Linker) Picture Quality : to set up picture quality for Network (5 : the highest quality)Ping Use : to confirm ping test to DVR AT Network

Bandwidth : to setup bandwidth for transmition

III. Setup Mode

Rebooting should be done when any setting value was changed at Network Setup

[to confirm saving the changes] [to confirm rebooting system]

TIP #9.setting value for rebooting after Network setup

34

7. Sensor Setup

III. Setup Mode

1

2

3

4

5

1

2

3

4

5

Sensor : to choose the sensor to be set

Setting Up : N/O (Normal Open) or N/C (Normal Close) setting

Storing : to select the camera for recording after sensor working selected camera is distinguished by yellow color

Alarm : to set up the Alarm for sensor working

Period of Time : to set the recording time

[Sensor Setup window]

35

8. Alarm Setup

III. Setup Mode

[Alarm Setup window]

1

2

3

1

2

3

Alarm : to select Alarm

Setting Up : to setup N/O (Normal Open) or N/C (Normal Close)

Alarm lasting time : Period for Alarm working

36

[PTZ window]

9. PTZ Control Mode

1

2

34

56

1

2

3

4

5

6

Camera : to select camera for PTZ control

PAN/TILT :to control PAN / TILT

FOCUS : to control Focus

LIGHT : to control Light

ZOOM : to control Zoom in /Zoom out

POWER : to control Power

Not to change the set value at PTZ modeOnly to control camera with PAN / TILT function can be used for control

TIP #10. setting value for rebooting after Network setup

III. Setup Mode

37

10. Backup Mode

III. Setup Mode

1

2

3

To set up the date for back up

To confirm the date when data was recorded : the date of recording date can be shown by red color

Backup : Back up the recorded file (by USB HDD) ( file format to be played back thru Eye-Linker after back up)

1

23

4

[Backup window]

4 AVI Export : AVI format for back up (USB HDD) (file format to be played back thru Windows Media Player

38

III. Setup Mode

[Backup window]

1

2

3

4

5

6

DVR System side : Left side for DVR System

Description of recorded file : File list of recording at selected date

sign for back up function : Channel Auto Switching for1, 4, 8, 9, 13

Information status : Working status for back up

USB HDD side :

Description of file after finishing back up :

1

2 3

4

5

6

To start backing up

To start restoring

To delete the list selected

To select all list

39

III. Setup Mode

TIP #11. How To Backup

How to back up (back up for AVI Export is under almost same way)

[to choose the date to be back up]

[select the list to be back up]

After selecting the list for back up by “Enter” , workingMessage for back up will be on, then back up will be starting by “Yes”

[back up is on going] [finishing back up]

40

11. System Administration

III. Setup Mode

[System Administration window]

1

2

Setup Initializing : Back to the initial setup

Log Backup : to back up the present System Log by USB HDD

1 2 3 4

5

Confirm : under initializingCancel

Confirm Cancel

41

3

4

5

Hard Disk Initializing : Initializing after deleting all recorded files

Status Windows : Status of each menu

Upgrading Version : Application S/W Upgrade

Connect to Server : nothing applicableConnect to Local : when upgrade for latest version by USB, but can not working, it can be back to old versionConnect to USB : upgrade S/W by USB Memory

Confirm Cancel

III. Setup Mode

42

12. Search Mode

III. Setup Mode

1

2

3

4

5

Normal : Normal Searching

Event : Searching for the recording data through the event from motion detecting or sensor

Recording data status: The date marked in red color is the date that has recorded data

Displaying the time that has recorded data in the selected date

[Search Mode]

1

2

3

4

6

Selecting date and time to search

5

6 Displaying the camera status :

The camera has recorded data.

The camera doesn’t have recorded data.

43

III. Setup Mode

1

2

Monitor Area: Displaying recording data1

2 Current Status

PlayingStop (or pause)

FF x 1( x2, x4)REW x 1( x2, x4)

Waiting

44

Window can be divided by “DIV” button in the Search Mode.

TIP #12. “DIV” function in the Search Mode

[16]

[full] [4]

[9]

III. Setup Mode

[Camera 1,2,3,4]

[Camera 13,14,15,16]

[Camera 5,6,7,8]

[Camera 9,10,11,12]

TIP #13. , in the Search Mode

45

IV. DVR Application Troubleshooting

Guide

# 1. No recording

Answer 1 : Verify if recording icon ( ) is displayed in the Surveillance Mode

Answer 2 : Verify if “recording status” in Camera Setup is Do Not RecordDo Not Record . If so, change it to Full RecordFull Record or ScheduleSchedule

Answer 3 : Verify if the setting is “record”( ) in the Schedule Setup when recording status is ScheduleSchedule.

Answer 4 : Use “REC” function in the Surveillance Mode regardless of setup data of each camera, if necessary.

# 2. Not recording in the Schedule mode

Answer 1 : Verify if “recording status” in the Camera Setup is Schedule.Schedule.

If the recording status is Full RecordFull Record or Do Not Record, Do Not Record, it won’t work with the schedule you setup.

# 3. Not recording in the motion detecting mode

Answer 1 : Verify if “recording status” in the Camera Setup is ScheduleSchedule , if you want to use motion detecting recoding mode.

Answer 2 : Verify if the setting is “motion” ( ) in the Schedule setup when recording status is ScheduleSchedule.

46

# 4. Stored data are deleted.

Answer 1 : When time is newly set, all of the stored data will be deleted. (Warning!)

Answer 2 : If you initialize HDD in the System Administration Setup, all date will be deleted.

# 5. Not working with the control of the PTZ Camera

Answer 1 : Verify if “PTZ Type / ID” is correct in the Camera Setup

Manufacturer Model

ONIX CNB-PTZ102N

DONGYANG UNITECH DRX-500

ORIENTAL SYSTEM DVRX-1000

HONEYWELLHSDN-251

HRX1000

SAMSUNG SCC-641

SAMSUNG TECHWINSRX100B

SPD-1600

KODICOM KRD-301/302

PELCO PELCO-D

TRINUS PT-100-200

LG LPT_A100L

FILTEK PT_102

[supporting PTZ]


Guide

47

# 6. the screen of specific camera channel is OFF or the quality of image is poor.

Answer 1: Check if there is any problem with camera or camera adapter and connection line.


Guide

# 7. No power to the DVR system

Answer 1 : Check if there is any problem with power, power cable and power connector.

# 8. Not showing Surveillance Mode after booting

Answer 1 : If it will not show Surveillance Mode after booting the system, the file system of HDD can be damaged. Please contact the installed company, distributor or our head office.

※ In case when a problem is not solved despite of the verification of above contents, contact the installed company, distributor or our head office.

48

Chapter 3.

Eye-Linker User’s Guide

49

Eye-Linker program is the DVR Network Client program to be installed on the Window OS based PC which supports remote real time monitoring, controlling, searching, backup, setup by accessing the several Linus OS DVRs connected each other thru Network

General

- Eye-Linker is for remote monitoring CCTV Video channel transmitted thru network by accessing one of several Linux DVRs connected each other by network.

- Monitoring the selected cameras from DVRs connected by network.

Real time monitoring for several DVRs thru Network

Remote DVR SystemData input

Accessing DVRReal time remote

monitoring for selected cameras

Seoul

Pusan

Inchon Pohang

Jeju

I. Features of Eye-Linker

50

Function for searching thru Eye-Linker program for video data at remote DVR system

- Network searching for the video data by month, day, time, camera at remote DVR thru the same interface with DVR.- Printing out the data after searching by JPEG.- Function of image filtering and enlarging and reducing searched images.

Real time searching thru network for data in DVR system

I. Features of Eye-Linker

- Function to change auto channel switching, rebooting cycle setup key, basic setting key of remote camera, each sensor key, etc

To change the setup mode of remote DVR system

Remote back up function thru eye linker by date, hour, time, camera at remote DVR system of which file formats are Linux DVR system own format( LDV,IDX) and or AVI in general.

Network backup function for DVR system

51

1.System spec. to be recommended for Eye-Linker

II. Installation guide of Eye-Linker

- CPU : Pentium III 800GHz or above- Memory : 256MB or above- HDD : 20MB or above- OS : Windows 2000 / XP / 2003

Recommended spec.

*Note*Check your HDD space if you want to backup files from remote DVRs

2. Installation steps for Eye-Linker

1) Run “Setup.exe”

To run the Eye-Linker program by double click the Setup.exe

52


2. Installation steps of Eye-Linker

2) Eye-Linker Setup

To choose the langague (Korean, English, Japan)

1

2 3

4

53

3. To run Eye-Linker


-Double click the icon on Window screen. Or “C:\ProgramFiles\Leadtech\EyeLinker\EyeLinker.exe

To run Eye-Linker

The message is to be on the screen when initially execute Eye-Linker programIt is not error so click the “OK”

[Initial mode]

54

Description of screen

1

1

2

3

4

6

5

Monitoring area : real time monitoring for maximum 16 screen of remote camera.

To click the right side mouse button - Image filtering - reducing/ enlarging - real time storing- to control the out side devices hooked into DVR

Status for Camera connectivity of DVR.

[camera status]

III. User’s guide of Eye-Linker

55


2To management groups and lists for remote DVRs : Add/Remove/Modify the groups and the lists of remote DVRs

Eye-Linker is designed for accessing to several remote DVRs at the same time.The list of DVR groups can be chosen, then the information of these groups will be on the screen.

TIP #1. How to list up the remote DVR

Add/Remove/Modify Groups (Selection of Group by double click)

[Screen for Group Management]

- Server name : Remote DVR name- Change Group : To choose the group of DVR to be added- Connection Type : TCP/IP, ISDN, Local - IP SERVER : When allocated IP by ADSL or DHCP, inputting ID of DVR System , controlling the finally changed IP of DVR, setting value to connect the remote DVR by Eye-Linker- IP : inputting fixed IP address- port :Port number (Default: 5005)- Folder : In case of connecting to Local - Password: Password of the remote DVR (Default: 0000)- Memo : Description for the remote DVR- Server Status Description: To check the remote DVR- Cameras for auto Connect: To choose cameras for showing images automatically when you connect the remote DVR- Save Folder: When back up for the remote DVR, the folder to be store the backup data

Description of screen in detail

56


TIP #2. How to connect or disconnect the remote DVR

To choose DVR

To connect remote DVR To disconnect remote DVR


Click “Connect” then showing the video images of the remote DVR

57


4 Divided screens for real time monitoring

3 To control the Pan/Tilt/Zoom for cameras thru Eye-Linker

To control the direction of camera (The center button is for controlling PTZ Light )

To set up camera Focus

To control Zoom In/Out

1ch, 4ch, 9ch, 16ch

automatic channel switching for 1, 4, 9, 16ch manually control


58

5 To set up and finish Eye-Linker program

TIP 3. How to configure Eye-Linker

To finish the Eye-Linker

- Screen: To set up screens - Alarm : To set up warning and sensor- Connection: To set up connection- DVR IP Server : When using ADSL or DHCP

*Note*To set up DVR IP server surely when IP address is allocated by ADSL or DHCP. Leadtech is now operating IP server(Static IP: 211.105.46.29)


[Screen for EyeLinker configuration ]


59

6 Functions for controlling Camera/Sensor/Alarm, setup, search, backup in relation to real time monitoring of remote DVR Systems

1 Information of currently connected DVR System (Model, Name, Version, HDD Used percent)

2 Status for camera of currently connected DVR system (To be changed by mouse click ) connected disconnected

3 Status of sensor

4 Status of alarm

5 Set up : remote setting up the remote DVR system

To enter password

[ screen for setting of remote DVR ]


1 2

3

4

5 6 7 8 9 10


Gatheing configurations of the remote DVR

60

TIP 4. To change the setting of remote DVR


General setting

[ Screen for general setting]

Camera setting

[ Screen for Camera setting ]


61


Schedule setting

[ screen of schedule setting ] [ example of schedule setting ]

Motion area setting

[ example of motion area setting ]

[ screen of motion area setting ]

TIP 4. To change the setting of remote DVR (Continued)


62


Sensor setting

[ screen of sensor ]

Alarm setting

[ screen of alarm ]

*Note*To remote set up the configuration of remote DVR is same way with DVR

TIP 4. To change the setting of remote DVR (Continued)


63

6 Search: To search the recorded images of remote DVR system

Click “Search”

Click “Search” on the Search mode to select the servers (Remote DVRs)

[ Search Mode]

Select the Remote DVR you want to search. When the connection is “No” , click “Connect” then the remote DVR will be connected to the PC.

1. Select the remote DVR you want to search택2. Check if the connection is “YES” 3. Click “Select” on the DVR you select4. Ready for searching



64

TIP #5. How To Search

How to search remote DVR

When you select the DVR you want to search, it shows dates and time which have recorded images

- Bold letter date : There are recorded images on the date- Normal letter date : No recorded images on the date

- Green box( ): There are recorded images on the hour - Blank box( ) : No recorded images on the timeClick to the time you want to search in the time

table

Showing the recorded images on the selected time

Available to change searching speed in 5 levels

Searching Speed

Search Control

Time Control

Brightness,Contrast,Color/Mono,Saving recorded images,Print

Dividing,Channel Auto Switching



65

7 Back Up: Backup the recorded image files on remote DVR to the PC

Click “Backup” - Eye-Linker should be connected to the remote DVR when you want to backup

- Check the date and time (Bold – recorded images exist)- The checked boxes on Select Cam mean there are recorded images on the cameras- Select camera you want to backup

Click “Backup Start” when you select the period for backup

Select download folder

[Backup Progressing]

[Backup Finished]



66

8 Log View : Showing the logs of Eye Linker

Click “Log View”

Showing the log of “Eye-Linker” Application

9

Click “Check Watermark”

Check Water Mark : To Verify if the JPEG file from the DVR is modified or forged

Select the file to verify*Note*You will know if the JPEG file is modified after selecting the file.



67

10

Click “Avi Export”

Avi Export: Backup the recorded image files which are converted to AVI format on remote DVR to the PC. Please refer the “backup” part in this manual.7



68

IV. Eye-Linker Troubleshooting Guide

# 1. No connection to DVR

Answer 1 : Verify if network is working on the PC where the Eye-Linker is running.

Answer 2 : Check the network setup in the DVR and verify if DVR is connected to network.

Answer 3 : Check if the remote DVR is working on.

# 2. Connected to remote DVR, but not showing any video images

Answer 1 : Edit the server you want to connect and select the cameras which are automatically connected when you connect the DVR

Answer 2 : Check if the camera icon is on in the main screen of Eye-Linker

connected to camera not connected to camera

69

IV. Eye-Linker Troubleshooting Guide

# 3. Unable to search for remote DVR

Answer 1 : Check if the PC connected to the DVR.

Answer 2 : Check if there are recorded images on the date you want to search.

Answer 3 : Check if the selected camera is on.

# 4. Unable to backup when you click the backup button

Answer 1 : Check if there are recorded files on the date you want to backup. Please refer the Backup part again.

Answer 2 : Check if the checkbox of the camera you want to backup is checked.

If no checked on the “SelectCam”, the backup cannot be progressed.

# 5. Too slow to monitor in the display mode, the Search mode or to backup

Answer 1 : If you connect to many remote DVRs, the program can be slow because of the network bandwidth.

Answer 2 : When the speed of backup is too slow, please turn off the current monitoring cameras in the display mode.

Answer 3 : When the speed of searching is too slow, please turn off the current monitoring cameras in the display mode.

0 linux dvr self-kit user’s guide. 1 the contents of this user’s manual shall not be reproduced...

Documents