waiting, smoking and pedestrian shelters 44-47 theta waiting shelter 44 theta waiting shelter with...
TRANSCRIPT
HIGH-INTEGRITY
SHELTERS, COMPOUNDS,
WALKWAYS, CANOPIES
AND STREET FURNITURE
CI/SfB (90.7) x
DESIGN / MANUFACTURE / INSTALL
Apex Shelter Systems Ltd
Apex House
Units 3-4
26a Hart Street
Southport
Merseyside
PR8 6BT
T: 01704 546522
F: 01704 517437
www.apexshelters.co.uk
www.apexshelters.co.uk
2010 V.1
Contents
02 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 03
Introduction 4
Colour Charts 6
Roofing Materials 7
CYCLE AND MOTORCYCLE SHELTERS 8-23
Alpha Cycle Shelter 8
Alpha Motorcycle Shelter 9
Economy Alpha Cycle Shelter 10
Junior Alpha Cycle Shelter 11
Beta Cycle Shelter 12
Beta Motorcycle Shelter 13
Theta Cycle Shelter 15
Theta Motorcycle Shelter 15
Eta Infant Shelter 16
Delta Cycle Shelter 18
Delta Motorcycle Shelter 19
Gamma Cycle Shelter 20
Gamma Motorcycle Shelter 21
Castor Cycle Shelter 22
CYCLE AND MOTORCYCLE COMPOUNDS 24-28
Alpha Cycle and Motorcycle Compound 24
Locking Mechanisms 25
Theta Cycle and Motorcycle Compound 26
Wooden Shelters BREEAM Compliant 27
Opposing Alpha Cycle and Motorcycle Compounds 28
Opposing Theta Cycle and Motorcycle Compounds 30
Castor Cycle Compound 31
Alpha Gamma Combination Compound 32
Theta Delta Combination Compound 34
CAGES 35-36
Omega Cycle Cage 35
Lambda Cycle Cage 36
CYCLE LOCKERS 37
Sigma Horizontal Cycle Locker 37
Sigma Semi-Vertical Cycle Locker 37
RACKS AND STANDS 38-41
NU Double-Sided Cycle Rack 38
NU Sheffield Cycle Stand 39
NU Single-Sided Scooter Stand 40
NU Double-Sided Scooter Stand 40
Economy NU Single-Sided Scooter Stand 40
Economy NU Double-Sided Scooter Stand 40
OUTDOOR CLASSROOMS 41
Outdoor Classroom 41
LARGE UMBRELLAS 42-43
Zeta Umbrellas 42
WAITING, SMOKING AND PEDESTRIAN SHELTERS 44-47
Theta Waiting Shelter 44
Theta Waiting Shelter with Seating 45
Alpha T Waiting Shelter with Seating 46
Beta Waiting Shelter with Seating 47
PRAM/BUGGY SHELTERS 48
Hera Pram Store 48
Domed Roof Pram Shelter 49
Theta Buggy Shelter 50
Eta Buggy Shelter 51
YOUTH SHELTERS 53-54
Omicron Youth Shelter 51
Epsilon Youth Shelter 52
Sunburst Youth Shelter 54
MOBILITY SCOOTER/LOCKER SHELTERS 55-57
Mobility Scooter Shelters 55
Helmet Lockers 56
Cigarette Bins 56
Locker Shelters 57
WALKWAYS AND ENTRANCE CANOPIES 58-63
Paisley Entrance Canopies 59
Stirling Entrance Canopy 60
Dundee Entrance Canopy 61
Dumfries Lattice Walkway 62
Bin Compound 63
Theta Shelter incorporating Integral Single-sided Scooter Rack 63
SMOKING SHELTERS 64-65
Olympic Smoking Shelter 64
Theta Smoking Shelter 65
BOOT AND SHOE CLEANERS 66-67
Perseus Boot and Shoe Cleaner 66
Theseus Boot and Shoe Cleaner 67
Hercules Boot and Shoe Cleaner 67
Introduction
As well as our standard range of products, goods
can be custom-made to tailor-suit a specific site
or requirement.
Our team has over 20 years experience in the design,
manufacture and installation of street furniture. Risk
assessments and method statements are carried out in
accordance with CDM regulations. All work is covered
by our Personal Indemnity Insurance. If necessary,
where planning permission is required, a qualified
architect will facilitate the application on your behalf.
Costs for this service will vary for each project.
Shelters are designed to meet the structural integrity
standard BS 5950-1990 (structural use of steelwork in
building, Part 1).
Goods and installations are guaranteed for 12 months
parts and labour.
INSTALLATION
All shelters are supplied in kit form with
comprehensive installation instructions for ease of
assembly. Alternatively, we can provide a full quotation
for the manufacture, delivery and installation including
ground works, where necessary. We offer a free-of-
charge nationwide site survey to assess the site and
offer expert advice on the most suitable product for
the application.
Please note, that if you are installing a full concrete
plinth for a shelter, please allow an additional 500mm
of concrete to the width and length of the base.
DELIVERY
From receipt of order smaller items take approximately
3-4 weeks delivery. Shelters are on a 5-6 weeks lead
time from order. Bespoke products are 6-8 weeks from
acceptance of drawings. If you require goods sooner,
please ask as we can sometimes improve on
these estimates.
STEEL WORK FINISHES
Hot dipped galvanised – to BS EN ISO 1461:1999
This treatment offers a low-maintenance, long-lasting
finish for all types of environment. It is dull silver in
appearance. If requested when ordering, a certificate of
conformity can be supplied.
POLYESTER POWDER COATING
Powder coating has excellent outdoor exposure
qualities, as well as offering an attractive consistent
appearance in a variety of colours.
The importance of the finish is not only the visible top
coat, but, equally, the pre-treatment of the steelwork.
All Apex products are shot blast to SA2.5 to degrease
the surface and provide a key for the subsequent
processes. The steel is then etch-primed with Zinc
Phosphate anti-corrosive Primer then the final coat of
Polyester Powder is electrostatically sprayed onto the
surface to a thickness of 80 - 110 microns. The treated
steelwork is then heat-cured, melting the Polyester
Powder into a continuous phase and bonding it into
the steelwork. Polyester Powder Coats give high
durability and high resistance to weathering plus
excellent colour stability.
Another option available for powder coating is Extra
Life. This is a programme of coating systems that
offers product protection for up to 12 years. It
incorporates the latest powder primer technologies.
Please ask our Sales Department for a quotation
with Extra Life.
CONDITIONS OF SALE
Prices quoted are current at the date of printing.
Please use these costs as a guide reference only, due
to fluctuations in raw materials. Please contact our
sales department for a full quotation. All prices
exclude delivery charges, installation and VAT.
Due to printing limitations colours may vary slightly
to those shown in the brochure.
Dimensions are approximate and shown in millimeters.
Company Conditions of Sale are available upon request.
A RANGE OF QUALITY SHELTERS AND ASSOCIATED
STREET FURNITURE AT AFFORDABLE PRICES
04 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 05
There many stock colours to choose from so we have
listed our most popular colours below;
If, however, you require a colour we do not stock, this
will incur an additional charge. Alternatively we can
match your required colour to the nearest stock BS or
RAL Colour. Please speak to our Sales Department.
If requested, goods can be polyester powder coated on
top of the galvanized finish to give a more durable
resistance in extreme weather conditions. This does give
the products a rougher texture than the standard powder
coating due to the galvanized undercoat.
RAL 9005 – Black RAL 6002 – Forest Green
RAL 9010 – White RAL 5013 – Dark Blue
BS 00 A 05 – Light Grey BS 04 E 53 – Poppy Red
BS 18 E 53 – Solent Blue BS 18 B 25 – Merlin Grey
RAL 1023 - Yellow RAL 3004 - Burgundy
The reverse of the plastisol sheet comes as standard in a
grey polyester. The exposed face is supplied in a 200 micron
external grade PVC coating. The sheeting is non-
combustible and will not contribute to a fire. The roofing
sheets achieve a Class 0 rating in the Building Regulations.
CODES
To try and simplify our catalogue referencing a number
of standard pre-fixed are used throughout relating
cladding and racks. An example of this is the Theta
Tbep iR12, Theta is the model, Tbep transparent roof,
back panel and end panels and integral rack for 12
cycles. A key is listed below to refer to:
P – Plastisol Roof Cladding
Pep – Plastisol Roof and Transparent End Panels
T – 5mm thick transparent PET roofing
Tep – 5mm thick transparent PET roofing and end panels
B – back panel, this can be plastisol or PET
iR– Integral Rack, if there is a number following this it
relates to the capacity of cycles the rack holds.
R – floor-mounted rack
iMC – Motorcycle Rack
SCS – Single-sided Scooter Rack
SCD – Double-sided Scooter Rack
BF – Base Fix
SF – Submerged Fixed
P – Pedestal
I – Integral
AD – Additional Bay/Unit
Jnr – Junior Cycles, if sub-fixed after the shelter, it
refers to a smaller style shelter and rack if sub-fixed
after the rack it depicts a junior style rack.
Polyethylene Terephthalate (PET)
These high quality sheets are solid plastic – available in
transparent, smoked grey or opaque. They are extremely
impact-resistant and have an excellent fire rating
complying with BS 476:Part 7. The resistance to
weathering is guaranteed for 5 years (10 year available
upon request). They have a high chemical resistance so
even graffiti can be removed using an acetone free
solvent cleaner. PET is environmentally friendly with
ideal re-cycling properties. If not specified the sheets
will be supplied in 5mm thick transparent for the
cladding. There is an 8mm option available in both
transparent and opaque – there would be an additional
charge for this option.
Plastisol Coated Steel
Plastisol cladding (HP200®) offers excellent resistance to
corrosion and moderate weather resistance. Guaranteed
for a minimum of 10 years, it presents a hard-wearing
option available in 6 standard colours:-
Roofing MaterialsColour Chart
06 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 07
Picture shows example of the plastisol cladding in Solent Blue BS 18 E 53
Jade
14C37
Country Green Juniper Green
12B29
Slate Blue
18829
Willow
12B17
Moorland Green
12B21
Forest Green
RAL6002
Olive Green
12B27
Ivory
RAL9002
Mushroom
10B19
New Grey
10B23
Merlin Grey
18B25
White
00E55
Pigeon Grey
18B17
Goosewing Grey
10A05
Black
00E53
New Red
04D44
Buttermilk
10C31
Bamboo
08C35
Vandyke Brown
08B29
Terracotta
04C39
Wedgewood Blue
18C37
Ocean Blue
18C39
Pacific Blue
18E58
DESCRIPTION
Contemporary Shelter suitable to accommodate
cycles and/or motorcycles. Cycle racks can be adapted
to hold junior cycles and/or scooters (shelter showing
the incorporated scooter racks is shown on P54).
Motorcycles can be free-standing or the shelter can be
manufactured with an integral locking rail to the rear of
the shelter so motorcycles can be secured via chain or
D lock. Lockers can also be incorporated into the
shelter – please see image on P55 showing this.
GENERAL SPECIFICATION
Lengths: 2560mm, 3060mm, 4060mm and 5060mm
Capacity: 6 cycles or 2-3 motorcycles, 8 cycles or 3-4
motorcycles, 10 cycles or 4-5 motorcycles, 12 cycles or
5-6 motorcycles respectively
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 (Alpha P) or 5mm thick transparent PET (Alpha T)
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Alpha Cycle and Motorcycle Shelter
Picture shows a bank of 2 Alpha Tep iR12 Shelters with End Panels
08 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 09
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in a flat pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
ALPHA P iR CYCLE SHELTER
Loading: Single-sided into integral fully welded cycle
racks. If required, racks can be floor-mounted.
If junior versions are required, please contact the sales
department. Please enquire to the sales department if shelters are required to meet the BREEAM standards as the racks need to be spaced at 1000mm centres.
Alpha P iR6 £1,006.00
Alpha P iR8 £1,204.00
Alpha P iR10 £1,340.00
Alpha P iR12 £1,466.00
ALPHA T iR CYCLE SHELTER
Alpha T iR6 £1,180.00
Alpha T iR8 £1,325.00
Alpha T iR10 £1,604.00
Alpha T iR12 £1,795.00
Picture shows bank of 2 Alpha Shelters – 1 withmotorcycles and 1 for cycles
ADDITIONAL BAYS
Alpha Shelters can be supplied any length to suit
your requirements.
END PANELS (EP)
5mm thick Transparent PET End Panels are available
for the Alpha Shelter
Price per end panel £167.50
ALPHA IMC MOTORCYCLE SHELTERS
Loading: Integral fully welded rail to rear of
shelter for securing motorcycles.
ALPHA P iMC MOTORCYCLE SHELTERS
Alpha P iMC – 2.5m £937.00
Alpha P iMC – 3m £1,115.00
Alpha P iMC – 4m £1,210.00
Alpha P iMC-5m £1,310.00
ALPHA T iMC MOTORCYCLE SHELTERS
Alpha T iMC2.5 L: 2560mm £1,100.00
Alpha T iMC3 L: 3060mm £1,220.00
Alpha T iMC4 L: 4060mm £1,415.00
Alpha T iMC5 L: 5060mm £1,635.00 Picture shows 2 Alpha Pep iR12 shelters with end panels
Picture shows a bank of 2 Alpha P iR12 Shelters
DESCRIPTION
Due to the popularity of the Alpha Shelter, an
economy shelter has been designed to enable you to
keep the aesthetics, whilst reducing costs. The
shelters are supplied with floor-mounted cycle racks
or motorcycle locking rail, or alternatively
motorcycles can be free-standing in the shelter.
GENERAL SPECIFICATION
Lengths: 2060 and 4060mm
Capacity: 5 cycles and 2 motorcycles or 10 cycles
or 4-5 motorcycles
Loading: Into floor-mounted cycle rack
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Economy Alpha Cycle and
Motorcycle Shelter
10 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 11
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
ECONOMY ALPHA R CYCLE SHELTER
Loading: Single-sided into floor-mounted fully welded
cycle racks. If junior versions are required, please
contact the sales department.
Economy Alpha P R10 £1,230.00
Economy Alpha T R10 £1,478.00
Loading: floor-mounted fully welded rail to rear of
shelter for securing motorcycles.
Economy Alpha P iMC6 £1,036.00
Economy Alpha T iMC5 £1,285.00
END PANELS (EP)
End Panels – 5mm thick transparent PET
Price per end panel £155.50
Picture shows...
Junior Alpha Cycle Shelter
DESCRIPTION
Alpha Curved Shelter to suit junior cycles
and/or scooters
GENERAL SPECIFICATION
Lengths: 4060mm
Capacity: 12 junior cycles
Overall width: 1800mm
Height to front: 1500mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour
on P7
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation
and are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
JUNIOR ALPHA iR CYCLE SHELTER
Loading: Single-sided into integral fully welded cycle
racks. If required, racks can be floor-mounted.
If junior versions are required, please contact the
sales department.
Alpha Junior P iR12 £1,115.00
Alpha Junior T iR12 £1,195.00
END PANELS (EP)
Junior Alpha End Panels are available in 5mm thick
transparent PET
Price per end panel £1,54.00
ADDITIONAL BAYS
Shelters can be supplied any length to suit
your requirements.
Please call the sales office for a quotation.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
DESCRIPTION
Beta shelters are suitable to accommodate cycle
and/or motorcycles. Cycle racks can be adapted to
hold junior cycles and/or scooters. Motorcycles can
be free-standing or the shelter can be supplied with
a locking rail to the rear of the shelter so
motorcycles can be secured via a chain or ‘D’ lock.
GENERAL SPECIFICATION
Lengths: 2560mm, 3060mm, 4060mm and 5060mm
Capacity: 6 cycles or 2-3 motorcycles, 8 cycles or 3-4
motorcycles, 10 cycles or 4-5 motorcycles, 12 cycles
or 5-6 motorcycles respectively
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard colour –
see colour chart P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete
or extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Beta Cycle and Motorcycle Shelters
Picture shows a Beta P shelter to hold motorcycles
12 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 13
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. If installing a concrete plinth
allow and additional 500mm concrete to front and width
of the shelter. A full nationwide installation service is
available including ground-works. Please contact the
sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
BETA CYCLE SHELTERS
Loading: Single-sided into integral fully welded cycle
racks. If required, racks can be floor-mounted.
If junior versions are required, please contact the
sales department.
BETA P iRCYCLE SHELTERS
Beta P iR6 £1,190.00
Beta P iR8 £1,295.00
Beta P iR10 £1,405.00
Beta P iR12 £1,522.00
BETA T iRCYCLE SHELTERS
Beta T iR6 £1,378.00
Beta T iR8 £1,482.00
Beta T iR10 £1,570.00
Beta T iR12 £1,644.00
BETA iMC MOTORCYCLE SHELTERS
Loading: Integral fully welded rail to rear of shelter for
securing motorcycles.
BETA P iMC MOTORCYCLE SHELTERS
Beta P iMC – 2.5m £1,050.00
Beta P iMC – 3m £1,125.00
Beta P iMC – 4m £1,225.00
Beta P iMC-5m £1,318.00
BETA T iMC MOTORCYCLE SHELTERS
Beta T iMC – 2.5m £1,240.00
Beta T iMC – 3m £1,260.00
Beta T iMC – 4m £1,408.00
Beta T iMC-5m £1,460.00
ADDITIONAL BAYS
Shelters can be supplied any length to suit
your requirements.
Please call the sales office for a quotation.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Picture shows a bank of 2 Beta P iR12 Shelters
Picture shows a bank of Beta Shelters to cover existing racks
DESCRIPTION
The Theta shelter is ideal for sorting either cycle
and/or motorcycles. Cycle racks can be adapted to
hold junior cycles and scooters. Motorcycles can be
free-standing or the shelter can be supplied with a
locking rail to the rear of the shelter so motorcycles
can be secured via a ‘D’ lock.
GENERAL SPECIFICATION
Lengths: 2560mm, 3060mm, 4060mm and 5060mm
Capacity: 6 cycles or 2-3 motorcycles, 8 cycles or 3-4
motorcycles, 10 cycles or 4-5 motorcycles, 12 cycles or
5-6 motorcycles respectively
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Theta Cycle and Motorcycle Shelter
Picture shows a Theta Tbep iR12 cycle with transparent roof, back and end panels
14 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 15
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
THETA CYCLE SHELTER
Loading: Single-sided into integral fully welded cycle
racks. If required, racks can be floor-mounted. If
junior versions are required, please contact the
sales department.
THETA P iR CYCLE SHELTER
Theta P iR6 £1,138.00
Theta P iR8 £1,223.00
Theta P iR10 £1,347.00
Theta P iR12 £1,463.00
THETA T iR CYCLE SHELTER
Theta T iR6 £1,150.00
Theta T iR8 £1,234.00
Theta T iR10 £1,432.00
Theta T iR12 £1,567.00
THETA IMC MOTORCYCLE SHELTERS
Loading: Integral fully welded rail to rear of shelter for
securing motorcycles.
THETA P iMC MOTORCYCLE SHELTERS
Theta P iMC2.5 £1,025.00
Theta P iMC3 £1,070.00
Theta P iMC4 £1,165.00
Theta P iMC5 £1,260.00
THETA T iMC MOTORCYCLE SHELTERS
Theta T iMC – 2.5m £1,033.00
Theta T iMC – 3m £1,068.00
Theta T iMC – 4m £1,250.00
Theta T iMC-5m £1,335.00
ADDITIONAL BAYS
Shelters can be supplied any length to suit
your requirements.
Please call the sales office for a quotation.
Picture shows a bank of 3 Theta Pbep iR12 Shelters with bespoke back panels and end panels
BACK PANELS
Back panels Plastisol Coated Steel £135.00 based on
5m shelter
Back panels 5mm thick transparent PET £399.00 based
on 5m shelter
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
END PANELS (EP)
Theta End Panels are
available in 5mm thick
transparent PET
Price per end panel £164.00
Picture shows a Theta Cycle Compound clad with hardwood panels
DESCRIPTION
The Eta Shelter is a infant adaptation of our popular
Alpha Shelter. The shelter has a floor-mounted nu
toastrack cycle rack.
GENERAL SPECIFICATION
Lengths: 2560mm
Capacity: 8 junior cycles
Overall width: 1200mm
Height to front: 1200mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 5mm thick transparent PET
End Panels: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Eta Infant Shelter
16 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 17
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Loading: single-sided into floor-mounted fully welded
cycle rack.
Eta Tep R8 CYCLE SHELTER - £1,235.00
ADDITIONAL BAYS
Shelters can be supplied any length to suit your
requirements.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Picture shows Eta Tep General Shelter
DESCRIPTION
The Delta shelter is a dual access shelter for sorting
either cycle and/or motorcycles. Cycle racks can be
adapted to hold junior cycles and scooters.
Motorcycles can be free-standing or the shelter can
be supplied with a locking rail to the rear of the
shelter so motorcycles can be secured via a ‘D’ lock.
GENERAL SPECIFICATION
Lengths: 2560mm, 3060mm, 4060mm and 5060mm
Capacity: 12 cycles or 4-6 motorcycles, 16 cycles or 6-8
motorcycles, 20 cycles or 8-10 motorcycles, 24 cycles or
10-12 motorcycles respectively
Overall width: 3800mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 (Alternatively, shelter can be fitted with 5mm thick
transparent PET – please ask the Sales Office for prices)
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Delta Cycle and Motorcycle Shelter
Picture shows a Delta Shelter with a motorcycle rail one side of shelter and a cycle rack on the alternate
18 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 19
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
DELTA iR CYCLE SHELTER
Double-sided into integral fully welded cycle racks. If
required, racks can be floor-mounted. If junior versions
are required, please contact the sales department.
DELTA P iR CYCLE SHELTER
Delta P iR12 £1,810.00
Delta P iR16 £1,897.00
Delta P iR20 £2,135.00
Delta P iR24 £2,324.00
DELTA T iR CYCLE SHELTER
Delta T iR12 £2,200.00
Delta T iR16 £2,297.00
Delta T iR20 £2,535.00
Delta T iR24 £2,818.00
Picture shows a Delta P iR24 Shelter
Picture shows a bank of 5 Delta P iR24 Shelters
DELTA iMC MOTORCYCLE SHELTERS
Loading: Integral fully welded rail to rear of shelter for
securing motorcycles.
DELTA P iMC MOTORCYCLE SHELTERS
Delta P iMC – 2.5m £1,595.00
Delta P iMC – 3m £1,624.00
Delta P iMC – 4m £1,834.00
Delta P iMC-5m £1,975.00
DELTA T iMC MOTORCYCLE SHELTERS
Delta T iMC – 2.5m £1,900.00
Delta T iMC – 3m £1,995.00
Delta T iMC – 4m £2,233.00
Delta T iMC-5m £2,470.00
END PANELS (EP)
End Panels – 5mm thick transparent PET
Price per end panel £320.00
ADDITIONAL BAYS
Shelters can be supplied any length to suit
your requirements.
Please call the sales office for a quotation
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
DESCRIPTION
The Gamma shelter is a dual access shelter for
sorting either cycle and/or motorcycles. Cycle racks
can be adapted to hold junior cycles and scooters.
Motorcycles can be free-standing or the shelter can
be supplied with a locking rail to the rear of the
shelter so motorcycles can be secured via a ‘D’ lock.
GENERAL SPECIFICATION
Lengths: 2560mm, 3060mm, 4060mm and 5060mm
Capacity: 12 cycles or 4-6 motorcycles, 16 cycles or 6-8
motorcycles, 20 cycles or 8-10 motorcycles, 24 cycles or
10-12 motorcycles respectively
Overall width: 3800mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 (Alternatively, the shelter could be fitted with 16mm
triple wall polycarbonate)
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Gamma Cycle and Motorcycle Shelter
Picture shows...
20 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 21
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
GAMMA iR CYCLE SHELTER
Double-sided into integral fully welded cycle racks. If
required, racks can be floor-mounted. If junior versions
are required, please contact the sales department.
Please enquire to the sales department if shelters arerequired to meet the BREEAM standards as the racksneed to be spaced at 1000mm centres.
GAMMA P iR CYCLE SHELTER
Gamma P iR12 £1,757.00
Gamma P iR16 £1,853.00
Gamma P iR20 £2,045.00
Gamma P iR24 £2,237.00
GAMMA T iR CYCLE SHELTER
Gamma T iR12 £1,885.00
Gamma T iR16 £2,205.00
Gamma T iR20 £2,562.00
Gamma T iR24 £2,928.00
Picture shows a Gamma P iR24 Shelter
Picture shows a bank of 3 Gamma Pep iR24Shelters with lockable sliding gates
GAMMA iMC MOTORCYCLE SHELTERS
Loading: Integral fully welded rail to rear of shelter for
securing motorcycles.
GAMMA P iMC MOTORCYCLE SHELTERS
Gamma P iMC - 2.5m £1,600.00
Gamma P iMC - 3m £1,714.00
Gamma P iMC - 4m £1,905.00
Gamma P iMC - 5m £2,040.00
GAMMA T iMC MOTORCYCLE SHELTERS
Gamma T iMC - 2.5m £1,850.00
Gamma T iMC - 3m £1,980.00
Gamma T iMC - 4m £2,345.00
Gamma T iMC - 5m £2,658.00
END PANELS (EP)
Gamma End Panels are available in 5mm thick
transparent PET
Price per end panel £330.00
ADDITIONAL BAYS
Shelters can be supplied any length to suit
your requirements.
Please call the sales office for a quotation
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
DESCRIPTION
High-tech shelter suitable to accommodate both
cycles and/or motorcycles. Manufactured with
perforated sheets to the lower part of the shelter and
solid transparent sheeting to upper, complete with a
16mm triple wall polycarbonate roof.
GENERAL SPECIFICATION
Lengths: 4060mm
Capacity: 20 cycles or 8-10 motorcycles
Overall width: 2100mm
Height to front: 2550mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 16mm triple wall polycarbonate
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Castor Cycle and Motorcycle Shelter
22 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 23
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Castor R10 £1,720.00
Picture shows Castor R10
DESCRIPTION
Gates can be added to the Alpha Shelter to provide
additional security. Gates are fitted with a hasp and
staple (as standard) for padlocking. Padlocks are not
supplied. Alternative locking methods, such as key
operated or coin retain/return can be incorporated.
See page 25 for Locking Mechanisms. If the area is
restricted sliding gates could reduce the footprint
of the shelter.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 10 cycles or 4-5 motorcycles, 12 cycles or 5-6
motorcycles respectively
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standards BS or RAL
Colour or 5mm thick Transparent PET
End Panels: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Alpha Cycle and Motorcycle Compound
Picture shows a Bank of 3 Alpha Tep iR12 shelters with End Panels and Sliding Gates
24 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 25
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
ALPHA iR CYCLE COMPOUND
Loading single-sided into integral fully welded cycle
racks. If required, racks can be floor-mounted. If junior
versions are required, please contact the sales
department. Please enquire to the sales department if shelters are required to meet the BREEAM standardsas the racks need to be spaced at 1000mm centres.
ALPHA PEP iR CYCLE COMPOUND
Alpha Pep Comp iR10 £2,175.00
Alpha Pep Comp iR12 £2,340.00
ALPHA TEP iR CYCLE COMPOUND
Alpha Tep Comp iR10 £2,545.00
Alpha Tep Comp iR12 £2,810.00
Picture shows a Bank of 2 Alpha Tep iR12 Shelters with End Panels and Front-Opening Gates
LOCKING MECHANISMS
A range of locking mechanisms are available;
including a hasp and staple, which is fitted as
standard, unless specified, a sliding bolt, (padlocks
are not supplied with either above option), a coin
return/retain or a card swipe system.
DESCRIPTION
Gates can be added to the Theta Shelter to provide
additional security. Gates are fitted with a hasp and
staple (as standard) for padlocking. Padlocks are not
supplied. Alternative locking methods, such as key
operated or coin retain/return can be incorporated.
See Page 25 for locking mechanisms. If the area is
restricted sliding gates could reduce the footprint
of the shelter.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 10 cycles or 4-5 motorcycles, 12 cycles or 5-6
motorcycles respectively
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standards BS or RAL
Colour or 5mm thick Transparent PET
End Panels: 5mm thick transparent PET
Back Panels: Plastisol Coated Steel to a standards BS or
RAL Colour or 5mm thick Transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Theta Cycle and Motorcycle Compound
26 Tel: 01704 546522 Fax: 01704 517437
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
THETA TBEP iR CYCLE COMPOUND
Loading single-sided into integral fully welded cycle
racks. If required, racks can be floor-mounted. If junior
versions are required, please contact the sales
department. Please enquire to the sales department ifshelters are required to meet the BREEAM standards as the racks need to be spaced at 1000mm centres.
Theta Pbep COMP iR10 £2,298.00
Theta Pbep COMP iR12 £2,472.00
Theta Tbep COMP iR10 £2,526.00
Theta Tbep COMP iR12 £2,875.00
Picture shows a Theta Pbep Compound with a motorcycle locking rail inside
Tel: 01704 546522 Fax: 01704 517437 27
BREEAM Compliant Cycle
Storage Facilities
What is BREEAM?
BREEAM is a tool to measure the sustainability of
non-domestic buildings in the UK. By using a
straightforward scoring system BREEAM addresses a
wide-range of environmental and sustainability issues
and enables developers and designers to prove the
environmental credentials of their buildings to
planners and clients.
What are the BREEAM Requirements for Cycle Storage?
> The space is covered overhead and protected from rain
> The covered area and the cycle racks are set in or fixed
to a permanent structure and allow both the wheel
and the frame to be locked securely. Our racks are
located in a locked structure fixed to or part of a
permanent structure with CCTV surveillance.
> There is a minimum distance of 1.0m between cycle
racks, where the racks allow for two-sided parking,
and 0.8m for one-sided parking to enable bikes to be
easily stored and accessed.
> Racks positioned in a circular array and spaced in
accordance with the guidance in the New
Metric Handbook.
> There is a minimum distance from any obstruction of
300mm for single-sided use and 900mm for
double-sided use.
> Adequate Lighting is provided in accordance with
BS5489 part 1.
> The facilities are in a prominent site location that is
viewable from the building.
> The majority of the cycle racks are within 100m of a
building entrance (ideally within 50m). Or, in the case
of further or higher education buildings on a campus,
where it is not feasible to meet the 100m requirement
the assessor justifiably deems that the facilities are in
an easily accessible location for building users, the
credit may still be awarded.
Any of our cycle shelters can be manufactured in
accordance with BREEAM. Please notify the Sales
Department when requesting a quotation, as the rack
spacings differ to standard.
Picture shows a ThetaPbep Compound with
transparent back, front,gate and end panels
and plastisol roof
Wooden Shelters
If required, some shelters can be
manufactured to be able to
accommodate wooden slats.
The wood can be supplied by
yourselves or supplied by Apex
Shelter Systems.
The above shelter shows the Theta
Shelter which was manufactured
with additional struts to enable the
customer to clad the shelter after it
was delivered to site.
DESCRIPTION
Alpha Shelters can be used to create a lockable
compound by opposing 2 shelters. Lockable gates can
be fitted to one or both sides allowing 2 entrances.
Alternatively, one side can be fitted with a fixed
security panel. A variety of locking mechanisms are
available for the gate, including a hasp and staple
(which is fitted as standard) or a sliding bolt, (padlocks
are not supplied with either option), a coin return or a
coin retain or a card swipe system are also available.
Roof panels can be fitted to the walkway to provide
enhanced weather protection. Vandal-resistant lighting
can also be installed as required.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 20 cycles or 8-10 motorcycles, 24 cycles or
10-12 motorcycles respectively
Overall width: 6000mm
Height to highest point: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standards BS or RAL
Colour or 5mm thick Transparent PET
End Panels: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices quoted are shown for 2 opposing single units with
both a gate and a fixed panel or 2 gates and polyester
Powder Coated to a standard colour.
OP/ALPHA TEP iR CYCLE COMPOUND
Single or dual access compound with fully welded
integral cycle racks. If required, racks can be floor-
mounted. If junior versions or motorcycle racks are
required, please contact the sales department. Please
enquire to the sales department if shelters are
required to meet the BREEAM standards as the racks
need to be spaced at 1000mm centres.
OP/Alpha Tep COMP iR20 £4,485.00
OP/Alpha Tep COMP iR24 £4,860.00
ENHANCED WEATHER PROTECTION
Price per 4m section £500.00
Price per 5m section £520.00
Picture shows a bank of 2 OP/Alpha compound with covered walkway
Alpha Cycle and Motorcycle Compound
28 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 29
DESCRIPTION
Theta Shelters can be used to create a lockable
compound by opposing 2 shelters. Lockable gates can
be fitted to one or both sides allowing 2 entrances.
Alternatively, one side can be fitted with a fixed
security panel. A variety of locking mechanisms are
available for the gate, including a hasp and staple
(which is fitted as standard) or a sliding bolt,
(padlocks are not supplied with either option), a coin
return or a coin retain or a card swipe system are also
available. Roof panels can be fitted to the walkway to
provide enhanced weather protection. Vandal-
resistant lighting can also be installed as required.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 20 cycles or 8-10 motorcycles, 24 cycles or
10-12 motorcycles respectively
Overall width: 6000mm
Height to highest point: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standards BS or
RAL Colour or 5mm thick Transparent PET
End Panels: 5mm thick transparent PET
Back Panels: Plastisol Coated Steel to a standards BS
or RAL Colour or 5mm thick Transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
Opposing Theta Cycle and
Motorcycle Compounds
30 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 31
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices quoted are shown for 2 opposing single units with
both a gate and a fixed panel or 2 gates and polyester
Powder Coated to a standard colour.
OP/THETA TEP iR CYCLE COMPOUND
Single or dual access compound with fully welded
integral cycle racks. If required, racks can be floor-
mounted. If junior versions or motorcycle racks are
required, please contact the sales department. Please
enquire to the sales department if shelters are
required to meet the BREEAM standards as the racks
need to be spaced at 1000mm centres.
OP/Theta Tep iR20 COMP £4,404.00
OP/Theta Tep iR24 COMP £4,736.00
ENHANCED WEATHER PROTECTION
Price per 4m section £500.00
Price per 5m section £520.00
Picture shows an OP/Theta Tbep iR24 compound with a set of lockers
Picture shows Castor Compound
Castor Cycle and
Motorcycle Compound
DESCRIPTION
High-tech secure compound suitable to accommodate
both cycles and/or motorcycles. Manufactured with
perforated sheets to the lower part of the shelter and
solid transparent sheeting to upper, complete with a
16mm triple wall polycarbonate roof.
GENERAL SPECIFICATION
Lengths: 4060mm
Capacity: 10 cycles or 4-5 motorcycles
Overall width: 6000mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 16mm triple wall polycarbonate
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Price on application
DESCRIPTION
This compound uses the Alpha and Gamma Shelters to
make valuable use of larger areas. Two lockable gates
can be fitted to one or both sides of the compound
allowing 4 entrances. Alternatively, one side of the
compound can be fitted with fixed security panels to
prevent access. A variety of locking mechanisms are
available for the gate, including a hasp and staple
(which is fitted as standard) or a sliding bolt, (padlocks
are not supplied with either option), a coin return or a
coin retain or a card swipe system are also available.
Roof panels can be fitted to the walkway to provide
enhanced weather protection. Vandal-resistant lighting
can also be installed as required.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 40 cycles or 16-20 motorcycles, 48 cycles or
20-24 motorcycles respectively
Overall width: 11000mm
Height to highest point: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standards BS or RAL
Colour and/or 5mm thick Transparent PET
End Panels: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices quoted are shown for 2 opposing single Alpha
units and a central Gamma Unit with 2 gates and 2 fixed
panels or 4 gates, polyester Powder Coated to a
standard colour.
ALPHA GAMMA SECURE CYCLE COMPOUND
Single or dual access compound with fully welded
integral cycle racks. If required, racks can be floor-
mounted. If junior versions or motorcycle racks are
required, please contact the sales department. Please
enquire to the sales department if shelters are required
to meet the BREEAM standards as the racks need to be
spaced at 1000mm centres.
Alpha Pep Gamma Pep iR40 COMP £7,306.00
Alpha Tep Gamma Pep iR40 COMP £7,872.00
Alpha Tep Gamma Tep iR40 COMP £8,313.00
Alpha Pep Gamma Pep iR48 COMP £7,743.00
Alpha Tep Gamma Pep iR48 COMP £8,437.00
Alpha Tep Gamma Tep iR48 COMP £9,054.00
Alpha Gamma Combination Cycle
and Motorcycle Compounds
32 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 33
ENHANCED WEATHER PROTECTION
Price per 4m section £1,000.00
Price per 5m section £1,040.00
ADDITIONAL SECURITY
For extra security within a compound why not have
another enclosure within the compound. The gates
can either be solid steel bars or fully clad with
5mm thick PET.
Gates can be added to each side of the shelter for extra
security. Cost per 5m Shelter £1,120.00
Picture shows an Alpha T Gamma P compound to hold 144 cycles
Picture shows Alpha Tep Gamma Tep iR40 COMP
34 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 35
Omega Cycle Cage
DESCRIPTION
The Omega Security Cage is ideal for the external
storage of cycles, motorcycles or scooter racks. The
robust mesh panels provide both high security
and visibility.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 10 cycles or 4-5 motorcycles, 12 cycles or 5-6
motorcycles respectively
Overall width: 2500mm
Height to highest point: 2150mm
Finish: Hot dipped galvanized to BS EN ISO 1461:1999
Roofing: Plastisol Coated Steel to a standards BS or
RAL Colour
Fixing: Base Fixed
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
OMEGA CYCLE CAGE
Single access compound with floor-mounted cycle
racks. If junior versions or motorcycle racks are
required, please contact the sales department.
Omega P R10 £3,565.00
Omega P R12 £3,705.00
Theta Delta Cycle and
Motorcycle Compounds
DESCRIPTION
This compound uses a combination of the Theta and
Delta Shelters to make valuable use of larger areas.
Two lockable gates can be fitted to one or both sides
of the compound allowing 4 entrances. Alternatively,
one side of the compound can be fitted with fixed
security panels to prevent access. A variety of locking
mechanisms are available for the gate, including a
hasp and staple (which is fitted as standard) or a
sliding bolt, (padlocks are not supplied with either
option), a coin return or a coin retain or a card swipe
system are also available. Roof panels can be fitted to
the walkway to provide enhanced weather protection.
Vandal-resistant lighting can also be installed
as required.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 40 cycles or 16-20 motorcycles, 48 cycles or
20-24 motorcycles respectively
Overall width: 11000mm
Height to highest point: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standards BS or
RAL Colour P7 and/or 5mm thick Transparent PET
End Panels: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete
or extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices quoted are shown for 2 opposing single Theta
units and a central Delta Unit with 2 gates and 2 fixed
panels or 4 gates and polyester Powder Coated to a
standard colour.
THETA DELTA CYCLE COMPOUND
Single access compound with floor-mounted cycle
racks. If junior versions or motorcycle racks are
required, please contact the sales department.
Theta Pbep Delta Pep iR40 COMP £7,835.00
Theta Tbep Delta Pep iR40 COMP £8,053.00
Theta Tbep Delta Tep iR40 COMP £8,320.00
Theta Pbep Delta Pep iR48 COMP £8,356.00
Theta Tbep Delta Pep iR48 COMP £8,610.00
Theta Tbep Delta Tep iR48 COMP £9,018.00
ENHANCED WEATHER PROTECTION
Price per 4m section £1,000.00
Price per 5m section £1,040.00
DESCRIPTION
The Lambda Security Cage is ideal for the external
storage of cycles, motorcycles or scooter racks.
GENERAL SPECIFICATION
Lengths: 4060mm and 5060mm, other sizes
are available
Capacity: 20 cycles or 8-10 motorcycles, 24 cycles or 10-
12 motorcycles respectively
Overall width: 5000mm
Height to lowest point: 2500mm
Finish: Hot dipped galvanized to BS EN ISO 1461:1999
Roofing: Plastisol Coated Steel to a standards BS or
RAL Colour
Fixing: Base Fixed
Construction: Shelters can be linked to form
continuous runs
Lambda Cycle Cage
36 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 37
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
LAMBDA CYCLE CAGE
Single access compound with floor-mounted
cycle racks. If junior versions or motorcycle racks are
required, please contact the sales department.
Lambda P R20 £5,632.00
Lambda P R24 £5,880.00
Picture shows the Lambda Cage for Scooter Racks with the option for clear back and sides
Sigma Cycle Lockers
DESCRIPTION
Individual Semi-vertical or Horizontal Cycle Lockers
supplied with a perforated viewing panel to the door.
Coat and helmet hooks are fitted inside the door. A
wheel support is inside the locker to guide the cycle
via a front wheel support to secure it.
Lockers are manufactured from galvanized panels witheither a sloped roof or an apex roof. The door is fittedwith a piano hinge and three point locking mechanism.
Other cladding options are available; perforated steelsheeting, transparent sheets, plastisol sheets or meshpanels. A variety of locking mechanisms are availableincluding a hasp and staple which is supplied asstandard, a T-handle, a coin return, a coin retain or acard swipe system. Double-sided lockers for 2 cyclesare available, please ask the Sales Department for details.
GENERAL SPECIFICATION
Lengths: 1200mm Semi-Vertical or 1900mm Horizontal
Capacity: 1 cycle
Overall width: 800mm
Height to lowest point: 1100mm Semi-Vertical or
1950mm Horizontal
Finish: Polyester Powder Coated to a standard BS or
RAL Colour
Fixing: Base Fixed
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full, nationwide
installation service is available including groundworks.
Please contact the sales office for further information.
Lockers are supplied fully assembled with 4 pre-
punched for securing into position. A full nationwide
installation service is available including groundworks.
Sigma Semi-Vertical £620.00
Sigma Horizontal £620.00
Picture shows a Bank of 6 Sigma Lockers
DESCRIPTION
This double-sided cycle rack enables the storage of 2
cycles per loop. The standard centres are 750mm;
however, these can be increased to 800mm, 900mm or
1000mm to comply with BREEAM, if requested. The
rack is fully welded with 4 pre-punched base plates for
bolting to concrete. This model is also available in
stainless steel at an extra cost.
GENERAL SPECIFICATION
Lengths: 1500mm, 3000mm or 3750mm
Capacity: 6, 10 or 12 cycles
Overall width: 750mm
Height: 800mm
Diameter: 48.3 x 3.2mm
Finish: Polyester Powder Coated to a standard BS or
RAL Colour
Fixing: Base Fixed (submerged fixed racks can be
supplied at an extra charge)
Nu R Double-Sided Floor
Mounted Cycle Racks
38 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 39
INSTALLATION
These racks are supplied fully welded for bolting into
concrete or setting into concrete. Larger racks may be
sent in more than one length for bolting together on site.
Nu- R6 £205.00 6 cycles
Nu- R10 £255.00 10 cycles
Nu- R12 £320.00 12 cycles
These racks are also available for infant/junior cycles
ref. Nu R10 jnr
Nu- R6jnr £185.00 6 junior cycles
Nu- R10jnr £235.00 10 junior cycles
Nu- R12jnr £300.00 12 junior cycles
Picture shows a bank of 2 racks
Nu Sheffield Cycle Stands
DESCRIPTION
Tubular cycle stand which can be supplied with base
plates for bolting to concrete or with extended legs for
setting into concrete. It is also available in stainless
steel at an extra cost.
GENERAL SPECIFICATION
Capacity: 1-2 cycles
Overall width: 750mm
Height: 800mm
Diameter: 42.4mm x 3.2mm
Finish: Polyester Powder Coated to a standard BS or
RAL Colour
Fixing: Base Fixed (submerged fixed racks can be
supplied at an extra charge)
INSTALLATION
These racks are supplied fully welded for bolting onto
concrete or setting into concrete.
Nu-BF £58.00 Base Fixed
Nu-SF £38.00 Submerged Fixed
These racks are also available for infant/junior cycles
ref. Nu SH jnr
DESCRIPTION
floor-mounted locking rail to secure motorcycles
GENERAL SPECIFICATION
Capacity: 4-5 motorcycles
Height: 300mm
Length: 4000mm
Finish: Polyester Powder Coated to a standard BS or
RAL Colour
Fixing: Base plates for bolting to concrete or extended
legs for submerging into concrete
INSTALLATION
These rails are fully welded for bolting onto or setting
into concrete
Price £205.00
Nu Motorcycle Locking Rail
Picture shows Nu-BF
Nu Scooter Stands
40 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 41
Nu-SCS5 £285.00 Single-Sided
Nu-SCS10 £328.00Nu-SCD10 £328.00 Double-Sided
Nu-SCD20 £398.00
DESCRIPTION
Economy scooter stands are manufactured without
pins. The scooter can be locked in position with the
users own padlock.
GENERAL SPECIFICATION
Lengths (single): 850mm, 1675mm
Lengths (double): 925mm, 1750mm
Capacity (single): 5, 10 scooters
Capacity (double): 10, 20 scooters
Height: 900mm
Finish: Polyester Powder Coated to a standard BS or
RAL Colour
Fixing: Base Fixed or Submerged Fixed
BNu- SCS10 £273.00
Single
BNu- SCD10 £315.00
BNu- SCD20 £385.00
Double
BNu- SCS5 £203.00
BNu- SCS10 £273.00
Economy Nu Scooter Stands
Outdoor Classrooms
IMPROVING OUTDOOR LEARNING
An outdoor classroom is ideal for an evolvingcurriculum, providing sensory experiences leading togreater levels of creativity and understanding. Theplayground is full of exciting things for the children toexperiment, discover and explore with. All our outdoorteaching facilities are built to combine practicality withsimple design. We offer a wide range of outdoorclassrooms that are available with optional seating andLighting. It is important to us that everybody using theclassroom has shelter from all weather conditionsthrough the provision of shade and shelter.
The outdoor Classrooms are suitable for Schools,National Parks, Zoos, Visitor Centres and other public areas.
The classrooms are custom-made to suit any size orapplication. A free-of-charge UK site visit is available.
There are a wide range of options for the material usedfor the manufacture of the classrooms.
Prices on request depending upon size and spefification.
DESCRIPTION
Scooter stands with pins to secure the scooter into
position. These can then be locked with the users own
padlock. If required, scooter racks can be incorporated
into a cycle shelter – see page 62. The racks can be
supplied with base plates for bolting down or extended
for sub-merging into concrete. These single-sided
racks can also be manufactured for bolting to a wall
where space is limited.
GENERAL SPECIFICATION
Single-Sided Lengths: 850mm
Double-Sided Lengths: 1675mm
Sided Lengths: 925mm and 1750mm
Capacity: 5, 10 scooters and 10 and 20 scooters
Height: 900mm
Diameter: 48.3 x 3.2mm
Finish: Polyester Powder Coated to a standard BS or
RAL Colour
Fixing: Base Fixed or Submerged Fixed
Zeta Umbrellas are a low-cost solution to provide cover
to large areas. They can provide valuable outside
teaching, seating and eating areas, preventing
over-exposure to the sun and let’s not forget the rain!
The fabric of the shade is a high quality polyester fabric,
230 grammes per square meter. It blocks out UV rays
and is waterproof – even in the heaviest of downpours!
Opening and closing the umbrella is made easy with a
removable crank or super- quick clamp handle
mechanism. The clamp mechanism can be opened and
closed in seconds and locked securely with the supplied
padlock to protect your investment.
The umbrellas are designed to withstand winds of 22-28mph dependent on size and model.
There are two methods for fixing the umbrellas. Option 1is an Inground Sleeve System. This consists of a lowersleeve which is anchored into the concrete and lies flushwith the ground. The outer sleeve is bolted to it withtamper resistant fixings. The sleeve is then secured tothe umbrella via a double clamp and a lockable bolt(again, lock supplied). Option 2 is a portable stand. Thisis a heavy duty galvanised steel base with the same
mechanisim as the inground sleeve clamp fixingattached. Concrete slabs supplied are then used tocreate a weight to secure the umbrella into position.Around 8-24 concrete slabs are supplied alongside eachumbrella depending upon the size of the umbrella. Thebase has adjustable feet positioned in each corner tolevel the umbrella if the ground is uneven.
Optional valances can be added to the umbrellas andalso a guttering system can be provided. Please call theSales Office for a full quotation.
There is a wide selection of colours available. The mostpopular shades are listed below; however, please contactus as other colours and patterns can be obtained ontothe valence at no additional cost. Professional printing isalso available at an additional cost.
The fabrics can be easily laundered commercially.Every umbrella is delivered in a rigid cardboardpackaging tube to ensure it reaches you as we send it.The tube packaging is dependent on size of the umbrellaand for larger umbrellas there will be a wooden pallet.
Zeta Umbrellas
42 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 43
CIRCULAR UMBRELLAS
Zeta I 3
3m diameter With In ground Sleeve£525.00
Zeta P 3
3m diameter Portable Base£570.00
Zeta I 4
4m diameter With In ground Sleeve£625.00
Zeta P 4
4m diameter Portable Base£1,060.00
Zeta I 5.5
5.5m diameter With In ground Sleeve£1,565.00
Zeta P 5.5
5.5m diameter Portable Base£1,555.00
Zeta I 10
10m diameter With In ground Sleeve£5,060.00
Zeta P 5.5
10m diameter Portable Base£5,360.00
SQUARE UMBRELLAS
Zeta I 2.2
2.2m x 2.2m With In ground Sleeve£240.00
Zeta P 2.2 x 2.2
2.2m x 2.2m Portable Base£260.00
Zeta I 3 x 3
3m x 3m With In ground Sleeve£715.00
Zeta P 3 x 3
3m x 3m Portable Base£735.00
Zeta I 3.5 x 3.5
3.5m x 3.5m With In ground Sleeve£1,025.00
Zeta P 3.5 x 3.5
3.5m x 3.5m Portable Base£1,050.00
Zeta I 4 x 4
4m x 4m With In ground Sleeve£1,220.00
Zeta P 4 x 4
4m x 4m Portable Base£1,245.00
Zeta I 5 x 5
5m x 5m With In ground Sleeve£1,645.00
Zeta P 5 x 5
5m x 5m Portable Base£1,650.00
Zeta I 7 x 7
7m x 7m With In ground Sleeve£4,085.00
Zeta P 7 x 7
7m x 7m Portable Base£4,120.00
DESCRIPTION
Pedestrian Shelter available with optional back, side
and/or front panels to suit your site requirements.
Panels available in 5mm thick PET, 8mm thick PET,
Plastisol Coated Steel or toughened glass.
GENERAL SPECIFICATION
Lengths: 5060mm as standard, these can be
manufactured to suit any length
Overall width: 2100mm as standard, this can be
manufactured to any width
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Theta Waiting Shelter
44 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 45
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Theta P £1,052.00 (Plastisol Roof)
Theta T £1,180.00 (Transparent Roof)
5mm thick Transparent Back Panel £300.00
End Panels £175.00 per end
Theta Waiting Shelter with Seating
DESCRIPTION
Pedestrian/Waiting Shelter with integral seating
available with optional back, side and/or front panels to
suit your site requirements. Panels available in 5mm
thick PET, 8mm thick PET, Plastisol Coated Steel or
toughened glass.
GENERAL SPECIFICATION
Lengths: 5060mm as standard, these can be
manufactured to suit any length
Overall width: 2100mm as standard, this can be
manufactured to any width
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Theta P £1,699.50 (Plastisol Roof)
Theta T £1,799.50 (Transparent Roof)
5mm thick Transparent Back Panel £300.00
End Panels £175.00 per end
DESCRIPTION
Alpha T Waiting Shelter with integral seating is an
attractive, robust shelter suitable for Schools, Railways,
Bus Terminals and Sports Grounds. Without end panels
it also complies with the government legislations for
Smoking Shelters.
GENERAL SPECIFICATION
Lengths: 5060mm as standard, these can be
manufactured to suit any length
Overall width: 2100mm as standard, this can be
manufactured to any width
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Alpha T Waiting Shelter with Seating
46 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 47
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Alpha T-Seat from £2,065.00
Alpha P-Seat £1,697.00
End Panels £167.50 per end
Beta Waiting Shelter with Seating
DESCRIPTION
An attractive shelter ideal as a waiting shelter. The
curve of the roofing ensures that rain water runs off to
the rear of the shelter.
GENERAL SPECIFICATION
Lengths: 3060mm, 4060mm and 5060mm
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard colour –
see colour chart P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. If installing a concrete plinth
allow and additional 500mm concrete to front and width
of the shelter. A full nationwide installation service is
available including ground-works. Please contact the
sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Beta P Waiting Shelters with integral seat
Beta P iSeat4 £1,501.00
Beta P iSeat5 £1,614.00
Beta T Waiting Shelters with integral seat
Beta T iSeat4 £1,768.00
Beta T iSeat5 £1,798.00
Picture shows a bank of 2 Beta 5m Waiting Shelters
Tel: 01704 546522 Fax: 01704 517437 4948 Tel: 01704 546522 Fax: 01704 517437
Hera Buggy Shelter
DESCRIPTION
The Hera Pram Store is a modern solution for the
storage of prams and buggies. There are a range of
options available for the shelter to suit a variety of
budgets. Additional features available include a locking
rail to secure the prams/buggies and lockable gates for
additional security
GENERAL SPECIFICATION
Length: 4100mm
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
PRICE: £1,680.00
DESCRIPTION
The Domed Roof Shelter has been specifically designed
for the external storage of prams and buggies. The
sophisticated shelter has a punch pad operated door
lock for security and transparent sheeting giving all
round visibility.
GENERAL SPECIFICATION
Lengths: 3000mm, 4000mm, 5000mm and 6000mm
Overall width: 2100mm
Height to front: 2700mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Features: 1 No. Lockable door to shelter as standard.
Doors available either side of shelter if required.
Domed Roof Pram Shelter
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Domed Roof Shelter
Price for 5000mm length £3,240.00
Picture shows 6m Domed Roof Pram Shelter
50 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 51
Theta Buggy Shelter
DESCRIPTION
The Theta style of shelter offers a practical and stylish
solution for the external storage of prams and buggies.
There are a range of options available for the shelter to
suit a variety of budgets. Additional features available
include a locking rail to secure the prams/buggies,
lockable gates for additional security, end panels and
back panels for extra weather protection.
GENERAL SPECIFICATION
Lengths: 2560mm, 3060mm, 4060mm and 5060mm
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Adjustable base plates for bolting to
concrete or extended legs for submerging into concrete
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
THETA BUGGY SHELTER
Theta P Buggy Shelter
Theta P 2560mm £920.00
Theta P 3060mm £2,197.00
Theta P 4060mm £2,347.00
Theta P 5060mm £2,531.00
Theta T Buggy Shelter
Theta T 2560mm £920.00
Theta T 3060mm £2,125.00
Theta T 4060mm £2,435.00
Theta T 5060mm £2,743.00
OPTIONAL EXTRAS
Length Plastisol PET Gates Integral
Back Back Hinged Locking
Panel Panel Rail
2560mm £121.00 £312.00 £485.00 £90.00
3060mm £140.00 £345.00 £500.00 £106.00
4060mm £178.00 £410.00 £530.00 £140.00
5060mm £214.00 £479.00 £560.00 £172.00
End Panels £164.00 per panel
Picture shows 2m Theta Tbep Pram Compound with rear locking rail
Picture shows Theta TbepCompound with plastisol roofingand transparent cladding
DESCRIPTION
The Eta shelter is a compact, space saving solution to
store prams and buggies. The shelter is available with
individual compartments which can be lockable via a
chain and users padlock.
GENERAL SPECIFICATION
Lengths: 3060mm, 4060mm and 5060mm
Overall width: 1200mm
Height to front: 1200mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Eta Buggy Shelter
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full
nationwide installation.
Capacity Length Shelter Compartments Chain Gates
6 3060mm £782.00 £314.00 £35.00 £300.00
8 4060mm £858.00 £440.00 £49.00 £364.00
10 5060mm £936.00 £567.00 £63.00 £429.00
PET end Panels £126.00 each
Picture shows Eta Tep Shelter with Integral Locking Rail
Picture shows Eta Tep Shelter with compartments and chain
52 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 53
Omicron Youth Shelter
DESCRIPTION
Modern eye-catching youth shelter which allows
teenagers to sit facing each other and socialise.
GENERAL SPECIFICATION
Lengths: 4000mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Galvanised steel or 5mm thick
transparent PET
Fixing: Base plates for bolting to concrete or extended
legs for submerging into concrete
Construction: Shelters are segmented and link together
to form circular shelter as shown in the photograph
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Full Product
Omicron P £5,999.00
Omicron T £6,200.00
Per Section
Omicron P Section £1,420.00
Omicron T Section £1,530.00
Per Additional Section
Omicron P-AD £1,145.00
Omicron T-AD £1,200.00
Picture shows Omicron Youth Shelter
Picture shows modified Omicron Shelter with Plastisol Roofing
DESCRIPTION
Hexagonal Youth Shelter incorporating seating
designed for comfort. Can be configured from a
minimum of 2 segments to a maximum of 7.
GENERAL SPECIFICATION
Lengths: 4000mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters are segmented and link together
to form a hexagonal shelter as shown in the diagram
Epsilon Youth Shelter
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Full Product
Epsilon P £4,995.00
Epsilon T £5,280.00
Per Section
Epsilon P Section £1,320.00
Epsilon T Section £1,430.00
Per Additional Section
Epsilon P-AD £695.00
Epsilon T-AD £735.00
54 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 55
Sunburst Youth Shelter
DESCRIPTION
Contemporary Youth Shelter incorporating seating
around the perimeter with a fixed central table. Ideal
for youths to congregate, grouped with the robust
design providing protection from the elements.
GENERAL SPECIFICATION
Lengths: 5600mm
Height to front: 2050mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard BS or RAL
Colour or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters are segmented and link together
to form a hexagonal shelter as shown in the diagram
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Full Product
Sunburst P £6,650.00
Per Section
Sunburst P Section £1,596.00
Per Additional Section
Sunburst P-AD £1,288.00
DESCRIPTION
The Mobility Scooter Shelter has been specifically
designed for the external storage of mobility scooters.
The attractive shelter has all round clear visibility
and a lockable door.
GENERAL SPECIFICATION
Lengths: 5060mm
Overall width: 3000mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: Plastisol Coated Steel to a standard Colour on
P7 or 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
Features: Lockable doors to the front of the shelter as
standard. Can be manufacture with sliding gates.
Mobility Scooter Shelters
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Price on application.
56 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 57
Locker shelters
Shelters can be custom-made for the external storage
of lockers. Below are varying designs which have been
specifically designed for the customer's requirements.
Helmet Lockers
PLASTIC LOCKERS
Cube lockers offer individual, personal security in the
school or workplace. Ideal for external use, these cube
lockers can be stacked together or bolted on top of
other lockers for extra storage space. Available with a
cam lock (supplied with 2 keys) or a hasp and staple or
padlocking (padlock not supplied). Finish is Grey body
available with a choice of colours for the door; blue,
cream, green, grey, red or white.
DIMENSIONS
Height: 305mm
Width: 305mm
Depth: 305mm
Price on application
WIRE MESH LOCKERS
1 bank of 2 nests of lockers offers 12 individual
compartments ideal for the storage of cycle helmets.
If these lockers are ordered in conjunction with the
iR12 or R12 cycle racks and shelters, the racks can be
manufactured to allow the lockers to stored beneath
the shelter between the racks as shown in the
photograph below.
DIMENSIONS
Height: 1980mm
Width: 305mm
Depth: 710mm
Price on application
Cigarette Bins
FLOOR-MOUNTED STEEL OR STAINLESS
STEEL CIGARETTE BINS ARE AVAILABLE
Large floor-mounted – CB1
Square Post Mounted Bin – CB2
Price on application
WALL MOUNTED OR POST
MOUNTED CIGARETTE BIN
Walkways and Entrance Canopies
58 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 59
All walkways and canopies are designed in accordance
to with BS5950 (Structural use of steelwork in
buildings) by an in-house drawing team.
Our designers can create a bespoke design dependent
upon our customers’ individual site requirements.
Canopies are also an excellent way to provide shade in
playgrounds, ether to cover external seating or provide
shade whilst children are queuing.
A site surveyor can attend site, free-of-charge to
measure up the area and provide a full quotation. This
can include all necessary ground works and installation
costs, if required.
On receipt of order CAD drawings will be supplied for
your approval. Once the drawings are approved this will
then go into fabrication.
The range of framework colours can be found on P??? of
the catalogue.
The roofing available for the walkways and canopies are
as follows:-
> PET Cladding – as shown on P7
Which is supplied as standard in 5mm transparent
PET, however, is available in 5mm Opal, Smoke Grey
Tinted and Bronze Tinted PET. For flat roofs and
shallow curves Clear and Opal PET is
also available in 8mm thick
> Plastisol Coated Steel – as shown on P7
> Filon GRP Cladding
Filon is a Glass Reinforced Polyester (GRP) available in
a choice of Opaque or Translucent finish. This option
offers good UV resistance and is an extremely strong
cladding. It also complies with the UK Building
Regulations and BS476 Fire tests.
> Triple Wall Polycarbonate
16mm triple wall poly is available in clear, bronze and
opal. Polycarbonate carries a 10-year warranty
covering loss of light transmission and loss of strength
due to weathering.
Paisley Entrance Canopy
The Paisley Entrance Canopy offers a contemporary
yet robust design. It is manufactured with heavy
duty square hollow section legs with a solid
polycarbonate roof. It can be tailor-made to suit
your requirements.
Each Canopy/Walkway is custom-made to suit any
area or application. A free-of-charge UK site visit
is available.
The roofing sheets are 16mm triple
wall polycarbonate.
Guttering can be incorporated.
Picture shows Stirling Entrance Canopy
Stirling Entrance Canopy
60 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 61
The Dundee walkway can either be wall and floor-
mounted or free-standing. It has an attractive curved
roof and can be manufactured to suit any location.
The walkway can be manufactured with heavy duty
square or round hollow section legs.
A free-of-charge UK site visit is available.
The roofing sheets are 16mm triple
wall polycarbonate.
Guttering can be incorporated.
Safety pads can be added to the legs of the shelter.
Dundee Walkway
The Stirling Entrance Canopy offers a contemporary
design at a low cost, The monopitch canopy is
manufactured with heavy duty square or round hollow
section legs with a solid polycarbonate roof. It can be
tailor-made to suit your requirements.
A free-of-charge UK site visit is available.
Prices upon request depending upon size
Dumfries Lattice Walkway
62 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 63
The Dumfries walkway is an ideal shelter to cover
larger areas with the lattice detailing doubling not only
as an attractive feature but also as a strengthener.
Each Canopy/Walkway is custom-made to suit any
area or application. A free-of-charge UK site visit
is available.
The roofing sheets are 16mm triple
wall polycarbonate.
Guttering can be incorporated.
Safety pads can be added to the legs of the shelter.
Shelter can be manufacture to incorporate wheelie
bins. Please contact our Sales Department with
your requirements.
Theta Bin Compound
Scooter racks can be incorporated into any bike
shelter. The photograph shows the Theta Design
incorporating a cycle rack and a scooter rack.
Theta Shelter Incorporating
Integral Scooter Rack
Olympic Smoking Shelter
64 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 65
Theta Smoking Shelter
DESCRIPTION
The Olympic Smoking Shelter is an attractive curved
roof shelter complying with the current UK
Government Smoking Shelter Regulations, Office of
Tobacco Control Regulations Ireland and The Smoking,
Health and Social Care (Scotland) - 50% of the wall
area open for ventilation. A perch seat can be added
to the rear of the shelter, if required.
GENERAL SPECIFICATION
Lengths: 3000mm, 4000mm
Overall width: 2000mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 5mm thick transparent PET
Cladding: 50% clad with 5mm thick transparent PET
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Price
Olympic 3m £1,150.00
Olympic 4m £1,290.00
DESCRIPTION
The Theta Smoking Shelter comp0lies with the current
UK Government Smoking Shelter Regulations, Office of
Tabacco Control Regulations Ireland and The Smoking,
Health and Social Care (Scotland) - 50% of the wall
area open for ventilation.
GENERAL SPECIFICATION
Lengths: 3060mm, 4060mm and 5060mm
Overall width: 2100mm
Height to front: 2100mm
Finish: Available in hot dipped galvanised or polyester
powder coated – see colour chart on P6
Roofing: 5mm thick transparent PET (plastisol coated
steel upon request)
Fixing: Adjustable base plates for bolting to concrete or
extended legs for submerging into concrete
Construction: Shelters can be linked to form
continuous runs
INSTALLATION
Shelters have been designed for ease of installation and
are supplied in flat-pack form with full technical
installation instructions. Alternatively, a full nationwide
installation service is available including ground-works.
Please contact the sales office for further information.
Prices shown are for a single unit Polyester Powder
Coated to a standard colour excluding delivery,
installation and VAT.
Price
Theta TSS3 £1,748.00
Theta TSS4 £1,882.00
Theta TSS5 £2,044.00
Boot and Shoe Cleaners
Perseus Boot and
Shoe Cleaner
DESCRIPTION
Fully Welded Boot and Shoe Cleaner with steel handle
frame. Fitted with a single row of heavy duty PVC
brushes. Framework painted in a durable, corrosion
resistant black hammerite paint. Brush tray at floor
level. Replacement brush sets are available.
GENERAL SPECIFICATION
Lengths: 915mm, 1220mm, 1830mm and 2440mm
Overall width: 85mm
Height: 1000mm
Finish: Black Hammerite Painted
Fixing: Either base plates for bolting to concrete or
extended legs for submerging into grass/concrete
PRICE:
Perseus915 £105.00
Perseus1220 £130.00
Perseus1830 £155.00
Perseus2440 £180.00
Theseus Boot and
Shoe Cleaner
DESCRIPTION
Fully Welded Boot and Shoe Cleaner with steel handle
frame. Fitted with a single row of heavy duty PVC
brushes. Framework painted in a durable, corrosion
resistant black hammerite paint. Brush tray 120mm
above floor level. Replacement brush sets are available.
GENERAL SPECIFICATION
Lengths: 915mm, 1220mm, 1830mm and 2440mm
Overall width: 85mm
Height: 1000mm
Finish: Black Hammerite Painted
Fixing: Extended legs for submerging into
grass/concrete
PRICE:
Theseus 915 £105.00
Theseus 1220 £130.00
Theseus 1830 £155.00
Theseus 2440 £180.00
Replacement Brush Sets for the Perseus
or the Theseus
915R £35.00
1220R £60.00
1830R £85.00
2440R £110.00
66 Tel: 01704 546522 Fax: 01704 517437 Tel: 01704 546522 Fax: 01704 517437 67
Boot and Shoe Cleaners
Hercules Boot and
Shoe Cleaner
DESCRIPTION
Fully Welded Boot and Shoe Cleaner with steel handle
frame. Fitted with a double row of heavy duty PVC
brushes. Framework painted in a durable, corrosion
resistant black hammerite paint. Brush tray set at
floor level. Replacement brush sets are available.
GENERAL SPECIFICATION
Lengths: 915mm, 1220mm, 1830mm and 2440mm
Overall width: 168mm
Height: 1000mm
Finish: Black Hammerite Painted
Fixing: Extended legs for submerging into
grass/concrete
PRICE:
Hercules 915 £155.00
Hercules 1220 £175.00
Hercules 1830 £195.00
Hercules 2440 £200.00