amplifiers ÷ 300 hertz adjustable high-pass cut frequency ... subwoofer digital amplifier ... mx 20...
TRANSCRIPT
AmplifiersThe task of an amplifier is to supply the right quantity of energy,
in order to drive the loudspeakers correctly, without altering the
music track. The high dynamic capacity and absolute tonal neu-
trality are both recognized features of all Coral's power amplifiers.
è compito dell'amplificatore fornire un'adeguata quantità di energia,
per pilotare correttamente gli altoparlanti, senza alterare il brano
musicale: elevata capacità dinamica ed assoluta neutralità timbrica
sono caratteristiche riconosciute a tutti gli amplificatori Coral.
XTA 4084 channel power amplifier
800 watt total music power
2 x 200 watt rms power (4 ohm)
4 x 100 watt rms power (2 ohm)
4 x 85 watt rms power (4 ohm)
separate A and B channel controls
45 ÷ 300 hertz adjustable high-pass cut frequency
12 dB/oct low-pass filter slope
45 ÷ 300 hertz adjustable low-pass cut frequency
12 dB/oct low-pass filter slope
+6 or +12 dB X-pander gain @ 50 hertz
10 ÷ 30K hertz (-3 dB) frequency response
0.05 % total harmonic distortion
90 dB signal/noise ratio
0.2 ÷ 7 volt RCA input sensitivity
22 K ohm RCA input impedance
1 ÷ 10 volt high-level input sensitivity
11 ÷ 15 volt power supply
66 ampere max power current
X-pander remote control supplied
240 x 390 x 56 mm - 4.1 Kg
XTA 2082 channel power amplifier
500 watt total music power
1 x 250 watt rms power (4 ohm)
2 x 125 watt rms power (2 ohm)
2 x 85 watt rms power (4 ohm)
45 ÷ 300 hertz adjustable high-pass cut frequency
12 dB/oct high-pass filter slope
45 ÷ 300 hertz adjustable low-pass cut frequency
12 dB/oct low-pass filter slope
90 dB signal/noise ratio
+6 or +12 db X-pander gain @ 50 hertz
10 ÷ 30K hertz (-3 dB) frequency response
0.05% total harmonic distortion
0.2 ÷ 7 volt RCA input sensitivity
22 K ohm RCA input impedance
1 ÷ 10 volt high-level input sensitivity
11 ÷ 15 volt power supply
heavy duty power terminals
34 ampere max power current
signal output RCA connectors
240 x 290 x 56 mm - 2.9 Kg
XTA 130subwoofer digital amplifier
1400 watt music power
700 watt rms power (1 ohm)
500 watt rms power (2 ohm)
300 watt rms power (4 ohm)
35 ÷ 250 hertz adjustable low-pass cut frequency
12 dB/oct low-pass filter slope
16 ÷ 80 hertz adjustable subsonic cut frequency
12 dB/oct subsonic filter slope
110 dB signal/noise ratio
0 ÷ 18 dB adjustable X-pander gain @ 40 Hz
0 ÷ 180 degree adjustable phase control
10 ÷ 250 hertz (-3 dB) frequency response
0.05 % total harmonic distortion
0.2 ÷ 7 volt RCA input sensitivity
22 Kohm RCA input impedance
1 ÷ 10 volt high-level input sensitivity
11 ÷ 15 volt power supply
70 ampere max power current
X-Pander remote control supplied
240 x 340 x 56 mm - 3.8 Kg
Il controllo remoto consente l’uso dell’ X-Pander dal posto di guida. The remote control allows the X-Pander adjustment from the driver's position.
La completezza della sezione “bass-processor” del modello XTA 130 rende possibili
innumerevoli configurazioni, senza l'uso di filtri elettronici esterni. La sezione “bass
X-pander” è comandabile a distanza tramite il controllo remoto fornito in dota-
zione, per plasmare il suono del subwoofer secondo le vostre esigenze. Inoltre, è
dotato di uscita di linea, per l'eventuale collegamento ad un altro amplificatore.
The completeness of the "bass-processor" section of the model XTA 130 makes possible numberless configurations, without the use of external
electronic crossovers. The "bass X-pander" section is adjustable by the supplied remote control, to mould the subwoofer sound according to your
needs. As well, the amplifier is equipped with line output, to be eventually connected to a further amplifier.
SubwoofersHDS 812subwoofer unit
700 watt max power
350 watt nominal power
25 ÷ 250 hertz frequency range
92 dB (2.83 V/1m) sensitivity
309 mm external diameter
60 mm voice coil diameter
butyl rubber surround
extend T-yoke magnetic system
HDB 10bass reflex subwoofer
500 watt max power
250 watt nominal power
80 ÷ 250 watt suggested amplifier
35 ÷ 250 hertz frequency range
90 dB (2.83 V/1 m) sensitivity
4 ohm nominal impedance
263 mm loudspeaker diameter
50 mm voice coil diameter
butyl rubber surround
360 x 305 x 307 mm box dimensions
8.8 Kg net weight
Il subwoofer HDB 10 fornisce bassi molto profondi e ben control-
lati, con elevata dinamica e distorsione ridottissima. Il cono in po-
lipropilene è rigido, leggero ed impermeabile. La bobina mobile
multi strato è avvolta su un supporto rinforzato con resine partico-
larmente resistenti al calore: questa tecnologia assicura una elevata
tenuta in potenza e notevoli escursioni, lineari e molto veloci.
The HDB 10 subwoofer supplies deep and properly con-
trolled basses, with high dynamics and very low distor-
tion. The cone is stiff, light and waterproof. The voice coil
is a multi-layer winding on a textile former treated with
high temperature resistant resins: this peculiar technology
gives huge linear excursion with the fastest acceleration.
HDS 808subwoofer unit
400 watt max power
200 watt nominal power
40 ÷ 400 hertz frequency range
90 dB (2.83 V/1m) sensitivity
212 mm external diameter
50 mm voice coil diameter
butyl rubber surround
extend T-yoke magnetic system
HDS 810subwoofer unit
500 watt max power
250 watt nominal power
30 ÷ 300 hertz frequency range
90 dB (2.83 V/1m) sensitivity
263 mm external diameter
50 mm voice coil diameter
butyl rubber surround
extend T-yoke magnetic system
I subwoofer della linea “HDS” forniscono bassi puliti e ben controllati, con una di-
namica impressionante e distorsione ridottissima. I coni in polpa di cellulosa sono
impregnati con speciali polimeri; le bobine mobili assicurano elevata tenuta in
potenza e notevoli escursioni lineari; le piastre polari nere ed i poli centrali ven-
tilati incrementano la dissipazione termica e riducono la compressione dinamica.
The "HDS" line subwoofers supply pure and powerful basses, impressive dynamic
range and very low distortion. The cones are moulded with air dried cellulose
pulp and impregnated with polymers; the voice coils assure high power han-
dling, linear and fast excursions; the black pole-plate and the vented T-yoke
improve the voice coil heat dissipation, reducing the dynamic compression.
DLK 1302-way stereo loudspeaker kit
80 watt max power, 40 watt nominal power
70 ÷ 20000 hertz frequency range
130 mm woofer, polypropylene cone
36 mm dome tweeter, neodymium magnet
5000 hertz, 12 dB/oct crossover filter
hi-pass electronic power control
DLK 1652-way stereo loudspeaker kit
80 watt max power, 40 watt nominal power
60 ÷ 20000 hertz frequency range
165 mm woofer, polypropylene cone
36 mm dome tweeter, neodymium magnet
5000 hertz, 12 dB/oct crossover filter
hi-pass electronic power control
I kit di altoparlanti della linea Daytona (DLK 130 e DLK 165) sono
adatti ad essere installati nei vani predisposti dalle case automobi-
listiche e collegati direttamente all'autoradio.
Kits
MK 1302-way stereo loudspeaker kit
200 watt max power
100 watt nominal power
60 ÷ 20000 hertz frequency range
92 dB sensitivity (2.83 V / 1 m)
130 mm woofer diametermica-polypropylene injection cone
49 mm neodymium tweetertreated silk dome, 26 mm voice coil
2-way filter, 3100 hertz crossover frequency3-step changeable tweeter levelhi-frequency electronic power control
MK 1652-way stereo loudspeaker kit
240 watt max power
120 watt nominal power
50 ÷ 20000 hertz frequency range
92 dB sensitivity (2.83 V / 1 m)
166 mm woofer diametermica-polypropylene injection cone
49 mm neodymium tweetertreated silk dome, 26 mm voice coil
2-way filter, 3100 hertz crossover frequency3-step changeable tweeter levelhi-frequency electronic power control
I kit di altoparlanti a due vie separate della linea Monza (MK 130 e
MK 165) sono completi di woofer, tweeter e crossover: possono es-
sere collegati direttamente ad ogni buona autoradio, ma forniscono
le loro migliori prestazioni se pilotati da un amplificatore di ade-
guata potenza. Sono stati sviluppati per essere facilmente installati
nei vani predisposti dalle case automobilistiche.
The Monza line 2-way separate loudspeaker kits (MK 130 and
MK 165), complete with woofers, tweeters and crossovers, can
be directly linked to each good car radio, but they supply its
best performances when driven by an adequate power ampli-
fier. They have been designed to be installed simply using the
car standard mounting holes.
The Daytona line loudspeaker kits (DLK 130 and DLK 165) are
suitable to be installed simply using the car standard mounting
holes, and directly connected to the car radio.
ComponentsThe Monza line components supply very good performance
combined with an easy installation. The mica-polypropylene cones,
the double-roll surrounds and the high flux of the magnet systems
provide linear response, sound transparency and tonal balance.
I componenti della linea Monza offrono prestazioni molto buone unite
alla semplicità di installazione. I coni in mica-polipropilene, le sospen-
sioni a doppia onda e l’elevato flusso dei complessi magnetici forni-
scono una risposta lineare unita a trasparenza e neutralità timbrica.
DLT 3636 mm neodymium tweeter
140 watt max power
70 watt nominal power
neodymium magnet
5 ÷ 20 Khertz frequency range
12 dB/oct crossover filter
electronic power control
DLW 165165 mm woofer
80 watt max power
40 watt nominal power
60 ÷ 5000 hertz frequency range
polypropylene cone
double roll surround
flux optimized T-Yoke
DLW 130130 mm mid-woofer
80 watt max power
40 watt nominal power
70 ÷ 5000 hertz frequency range
polypropylene cone
double roll surround
flux optimized T-Yoke
DLW 100100 mm mid-woofer
80 watt max power
40 watt nominal power
80 ÷ 5000 hertz frequency range
polypropylene cone
rubber surround
flux optimized T-Yoke
The Daytona line loudspeakers have been designed to be
installed simply using the car standard mounting holes, and
directly connected to the car radio. These units are the right
solution to an easy installation, still with a good quality level.
Gli altoparlanti della linea Daytona sono stati sviluppati per essere in-
stallati nei vani predisposti dalle case automobilistiche e collegati di-
rettamente all'autoradio. Questi componenti sono la risposta a chi de-
sidera un'installazione semplice, ma sempre di buon livello qualitativo.
MT 2549 mm neodymium tweeter
250 watt max power
100 watt nominal power
4 ohm nominal impedance
2.5 ÷ 20 Khertz frequency range
92 dB sensitivity (2.83 V / 1 m)
26 mm voice coil diameter
MX 202-way crossover filter
260 watt max power
130 watt nominal power
3100 hertz crossover frequency
6 / 12 dB/oct crossover slope
3 step tweeter level (- 2 / 0 / + 2 db)
hi-frequency electronic power control
65 x 90 x 30 mm
MW 165166 mm woofer
240 watt max power
120 watt nominal power
4 ohm nominal impedance
50 ÷ 6000 hertz frequency range
92 dB sensitivity (2.83 V / 1 m)
mica-polypropylene injection cone
26 mm voice coil, kapton former
DLC 8787 mm coaxial loudspeaker
120 watt peak power
40 watt nominal power
90 ÷ 20000 hertz frequency range
DLC 100100 mm coaxial loudspeaker
120 watt peak power
40 watt nominal power
80 ÷ 20000 hertz frequency range
DLC 130130 mm coaxial loudspeaker
120 watt peak power
40 watt nominal power
70 ÷ 20000 hertz frequency range
DLC 165165 mm coaxial loudspeaker
120 watt peak power
40 watt nominal power
60 ÷ 20000 hertz frequency range
DLC 91596 x 154 mm coaxial loudspeaker
120 watt peak power
40 watt nominal power
80 ÷ 20000 hertz frequency range
DLC 507140 x 190 mm coaxial loudspeaker
120 watt peak power
40 watt nominal power
60 ÷ 20000 hertz frequency range
Quando, per ragioni di spazio, non è possibile installare un sistema a
componenti separati, possiamo scegliere un altoparlante coassiale. Al
vertice della categoria troviamo i modelli della linea Monza: MC 130 e
MC 165 forniscono prestazioni insuperabili. I modelli della linea Dayto-
na (DLC) sono adatti ad essere collegati direttamente all'autoradio.
Coaxials
MC 130130 mm coaxial loudspeaker
120 watt max power
60 watt nominal power
60 ÷ 20000 hertz frequency range
92 dB (1 m / 2.83 V) sensitivity
mica-polypropylene injection cone
treated silk dome neodymium tweeter
In case it is not possible to install a separate components system,
because the space is not enough, we can chose a coaxial speaker.
The Monza line models are placed at the top of this category: MC
130 and MC 165 supply matchless performances. The Daytona line
models (DLC) are suitable to be directly connected to the car radio.
MC 165166 mm coaxial loudspeaker
160 watt max power
80 watt nominal power
50 ÷ 20000 hertz frequency range
92 dB (1 m / 2.83 V) sensitivity
mica-polypropylene injection cone
treated silk dome neodymium tweeter
TLK 5002-way stereo loudspeaker kit
100 watt max power 50 watt nominal power70 ÷ 20000 hertz frequency range130 mm titanium plated cone woofer • 25 mm voice coil• 55 mm installation depth20 mm silk dome tweeter• swivel installation accessories1-way crossover• 6 dB/oct slope - HF power control
• L O U D S P E A K E R C O M M O n F E AT U R E S • T I TA n I U M P L AT E D P O LY P R O P Y L E n E C O n E • n E O D Y M I U M T W E E T E R •
• A L U M I n I U M V O I C E C O I L F O R M E R • C H R O M E - P L A T E D P O L E P L A T E • S T R O n G R U B B E R S U R R O U n D •
TLK 6002-way stereo loudspeaker kit
140 watt max power 70 watt nominal power60 ÷ 20000 hertz frequency range165 mm titanium plated cone woofer • 25 mm voice coil• 58 mm installation depth20 mm silk dome tweeter• swivel installation accessories1-way crossover• 6 dB/oct slope - HF power control
TLC 400100 mm coaxial loudspeaker
90 watt peak power30 watt nominal power90 ÷ 20000 hertz frequency range45 mm installation depth
TLC 600165 mm coaxial loudspeaker
150 watt peak power50 watt nominal power60 ÷ 20000 hertz frequency range58 mm installation depth
TLC 500130 mm coaxial loudspeaker
120 watt peak power40 watt nominal power80 ÷ 20000 hertz frequency range55 mm installation depth
TLC 690165 x 234 mm coaxial loudspeaker
250 watt peak power90 watt nominal power50 ÷ 20000 hertz frequency range38 mm voice coil78 mm installation depthprotection grilles included
THE YOUNG LINE OF CORAL
Subwoofer suggested enclosures HDS 808 HDS 810 HDS 812
CLOSED BOX(small size)
volume 7 litres 13 litres 22 litres
sensitivity 87 dB @ 80 Hz 88 dB @ 55 Hz 90 dB @ 50 Hz
range 70 ÷ 120 Hz 50 ÷ 120 Hz 50 ÷ 120 Hz
CLOSED BOX(large size)
volume 10 litres 17 litres 32 litres
sensitivity 87 dB @ 70 Hz 88 dB @ 55 Hz 90 dB @ 50 Hz
range 60 ÷ 120 Hz 45 ÷ 120 Hz 45 ÷ 120 Hz
BASS-REFLEX(small size)
volume 10 litres 28 litres 37 litres
sensitivity 91 dB @ 68 Hz 93 dB @ 55 Hz 95 dB @ 60 Hz
range 52 ÷ 120 Hz 37 ÷ 120 Hz 42 ÷ 120 Hz
reflex tube Ø 74 x 200 mm Ø 74 x 170 mm Ø 94 x 200 mm
BASS-REFLEX(large size)
volume 14 litres 38 litres 52 litres
sensitivity 91 dB @ 53 Hz 92 dB @ 48 Hz 94 dB @ 50 Hz
range 45 ÷ 120 Hz 31 ÷ 120 Hz 35 ÷ 120 Hz
reflex tube Ø 74 x 210 mm Ø 74 x 170 mm Ø 94 x 180 mm
Loudspeaker data MT 25 MW 165
external diameter - mm 49 166
nominal impedance Zn ohm 4 4
max power Pm watt 250 240
nominal power Pn watt 100 120
sensitivity (2,83 V/1m) - dB 92 92
frequency range BW hertz 2.5K ÷ 20K 50 ÷ 6K
resonance frequency Fs hertz 1400 67
mechanical Q factor Qms - 1.30 4.38
electrical Q factor Qes - 1.52 0.71
total Q factor Qts - 0.72 0.61
moving mass Mms g - 12.9
compliance Cms mm/n - 0.44
emission diameter D mm 30 128
equivalent volume Vas litres - 10.2
force factor BxL n/A - 5.13
voice coil resistance Re ohm 3.4 3.4
voice coil inductance Le mH 0.03 0.36
linear excursion Xmax mm - ± 3.5
voice coil diameter - mm 26 26
cut out diameter - mm 43 142
Subwoofer data HDS 808 HDS 810 HDS 812
external diameter - mm 212 263 309
nominal impedance Zn ohm 4 4 4
max power Pm watt 400 500 700
nominal power Pn watt 200 250 350
sensitivity (2,83 V/1m) - dB 90 90 92
frequency range BW hertz 40 ÷ 400 30 ÷ 300 25 ÷ 250
resonance frequency Fs hertz 44 27 27
mechanical Q factor Qms - 12.28 5.19 5.42
electrical Q factor Qes - 0.52 0.53 0.48
total Q factor Qts - 0.49 0.48 0.44
moving mass Mms g 72.4 114.4 123.9
compliance Cms mm/n 0.18 0.30 0.28
emission diameter D mm 164 210 257
equivalent volume Vas litres 11 51 105
force factor BxL n/A 11.3 11.1 12.2
voice coil resistance Re ohm 3.3 3.3 3.3
voice coil inductance Le mH 1.6 1.7 1.3
linear excursion Xmax mm ± 7.7 ± 10.7 ± 5.6
voice coil diameter - mm 50 50 60
cut out diameter - mm 180 227 273
MarineOnda 60 è un elegante altoparlante due vie progettato per il settore
nautico. La sua struttura impermeabile lo rende adatto all’uso anche
in ambienti umidi come saune, piscine ecc. Il cestello integrale è rea-
lizzato in materiale plastico resistente ai raggi UV ed all’acqua salata.
Onda 60 is an elegant design two-way loudspeaker, developed
for nautical sector. The waterproof structure makes it suitable for
damp rooms like sauna, swimming-pool etc. The complete basket
is produced by UV rays and salt water resistant plastic material.
OnDA 60163 mm coaxial speaker 4 ohm nominal impedance
120 watt peak power 40 watt nominal power
90 dB (1 m / 2.83 V) sensitivity 60 ÷ 20000 hertz range
75 hertz resonance frequency 26 mm voice coil diameter
cono in polipropilene• polypropylene cone•sospensione in gomma• rubber surround•protezione centrale in gomma• rubber voice coil protection•trecciole rivestite e isolate• covered and insulated wires•impermeabile, protezione IP 54• waterproof, IP 54 protection•
Coral Electronic sr l _ 10098 Rivoli _ Torino _ Italy _ www.coralelectronic.com
Ci riserviamo il diritto di modificazioni senza preavviso. Decliniamo ogni responsabilità per eventuali errori o imprecisioni. We reserve the right to change specifications without notice. We decline every liability for any mistake or inaccuracy of this catalogue.
1399